Full Text Searchable PDF User Manual
1
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
IMPORTANT INSTRUCTIONS
PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE
Fireplace System Blower
MODEL #: GFB100
Compatible Fireplace Systems:
VFF-PH(20D)(20DB)(20D-C)(CPD-2T)
VFF-PH(26D)(26D-T)(IMD-2H)
VFF-PH(32DR)(32DR-H)(FSDR-2C)
IMGFB - 2015-04-06
WARNING:
IF THE INFORMATION IN THIS MANUAL IS NOT FOL-
LOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
WARNING:
THIS PRODUCT IS ONLY FOR USE WITH MODELS SPECI-
FIED IN THIS MANUAL BY THE MANFACTURER. ANY OTHER USAGE OR
INSTALLATION NOT SPECIFIED IN THIS MANUAL IS PROHIBITED.
Questions, problems, missing parts?
Before returning to your retailer, call
our customer service department at 1-877-447-4768,
8:30 a.m. – 4:30
p.m.,
CST, Monday – Friday or email us at customerservice@ghpgroupinc.com.
2
WARNING: This appliance is equipped with a three-prong (grounding) plug for
your protection against shock hazard and must be plugged directly into a properly
grounded three-prong receptacle.
1. Read all instructions before using this appliance.
2. If possible always unplug this appliance when not in use.
3. Do not operate any heater with a damaged cord or plug or after the appli-
ance malfunctions, has been dropped or damaged in any manner.
4. Under no circumstances should this appliance be modified. Parts having to
be removed for servicing must be replaced prior to operating this appliance
again.
5. Do not use outdoors.
6. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. Never locate this appliance where it may fall into a bath-
tub or other water container.
7. Do not run cord under carpeting. Do not cover cord with throw rugs, run-
ners or the like. Arrange cord away from traffic areas and where it will not
be tripped over.
8. To disconnect this appliance, turn controls to the off position, then remove
plug from outlet.
9. Connect to properly grounded outlets only.
10. This appliance, when installed must be electrically grounded in accordance
with local codes, with the current USA installations, or in the absence of lo-
cal codes, the National Electric Code, ANSI/NFPA No. 70.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock, fire or damage the appliance.
12. To prevent possible fire, do not block air intakes or exhaust in any manner.
13. Use this appliance only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock or injury
to persons.
14. Installation and repair should be done by a qualified service person. The
appliance should be inspected before use and at least annually by a pro-
fessional service person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc. It is imperative that
control compartments, burners and circulating air passageways of the ap-
pliance be kept clean.
SAFETY INFORMATION SAVE THESE INSTRUCTIONS
3
PACKAGE CONTENTS
REF #
PART #
DESCRIPTION
QUANTITY
A
XB001-01
Power Cord
1
B
XB002-01Q
Blower
1
C
XB003-01
Temperature Sensor
1
D
XB004-01Q
Connect Wire
1
E
PF06-0400-A
Rocker Switch
1
F
M4.2×8
Screw
10
G
VL057-03
Cable Tie
2
Parts List
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and diagram under. If any part is missing or dam-
aged, do not attempt to assemble, install or operate the product. Contact our
Technical Service Department at 1-814-643-1775.
A
C
B
D
E
F
G
• A Phillips head screwdriver is needed for installation.
4
ASSEMBLY INSTRUCTIONS
1.
Remove Blower Access Panel.
FF
2.
Mount Blower (B) onto bottom of
Fireplace Top using 4 screws (F).
3.
Attach Power Cord (A) to Blower
Access Panel.
4.
Attach Temperature Sensor (C) to
the Combustion Top using 2 sheet
metal screws.
1
2
3
Access Panel
Screws
Power Cord
Access Panel
WARNING:
This appliance is equipped with a three-prong (grounding) plug
for your protection against shock hazard and must be plugged directly into a
properly grounded three-prong receptacle.
Firebox must be disconnected from gas supply and removed from mantel
before installing fan accessory. Contact a qualified service person to do this.
BLOWER INSTALLATION (OPTIONAL)
4
Sheet
Metal
Screws
Senser
Bracket
Combustion Top
Mounting Holes
5
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
5.
Important: Insert the wires marked
with AUTO, OFF and MAN into line
slot on the right corner. Keep wires
close to the bottom.
5
6.
Insert two wires’ female plugs
marked with T1 and T2 (black and
yellow) into two male ports on
Temperature Sensor.
7.
Insert the female plug on the white
power supply wire (marked with
P1), into the corresponding male
port (marked with P1).
6
7
8.
Insert the female plug (marked
with P2) into the corresponding
male port, which is on the black
power supply wire (marked
with P2).
8
6
ASSEMBLY INSTRUCTIONS
9.
Insert the blower link (male plug)
into the power link (female port).
9
10.
Important
: Bind wires with cable
ties (G), and attach cable ties (G)
in holes on back of Outer Casing.
Attach one in hole near the top and
one in hole near the bottom.
10
11.
Insert AUTO, OFF, MAN wires
through the Rocker Switch
opening.
11
12
Fixed
Hole
G
E
12. Connect AUTO, OFF, MAN wires
to the three corresponding male
ports on the Rocker Switch (E).
Match the "Auto" wire to the
symbol " " and the "Man" wire
to the symbol " " on the rocker
switch (E).
7
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
13. Push Rocker Switch (E) into
Control Panel and secure.
13
14. Check that all wires are secure
and reattach Blower Access Panel
to Outer Casing. Capture the
Green Ground wire between the
Access Plate and Outer Casing
with the upper right screw.
E
1
1
2
2
3
3
4
4
A
A
B
B
C
C
D
D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dandowning
4/12/2013
DWG NO
Power Cord Attachment
TITLE
SIZE
C
SCALE
REV
Green Ground
Wire
14
Screw
Outer
Casing
Access Panel
Power Cord
8
OPERATING INSTRUCTIONS
Using Rocker Switch, turn blower on and check for operation. Turn on Rocker
Switch to the desired position. In the MAN position it will remain constantly on.
AUTO position will be controlled by the Temperature Sensor. To stop the opera-
tion turn Rocker Switch to the OFF position.
t
WHITE
GREEN
BLUE
BLACK
BLA
CK
AUTO OFF MAN
1
2
3
4
5
~120V
60Hz
1. Power Cord
2. Bushing Strain Relief
3. Blower
4. Temperature Sensor
5. Rocker Switch
FAN
Electrical Wiring Diagram
NOTE: If any of the original wire as supplied with the appliance must be replaced, it
must be replaced with a wire of at least an equal temperature rating.
CAUTION: Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation. Verify proper operation
after servicing.
9
MAINTENANCE OF MOTORS
Always disconnect the appliance from the main power supply and allow it to
cool before any servicing operation. The motor used on the flame blower is pre-
lubricated for extended bearing life and requires no further lubrication. However,
periodic cleaning/vacuuming of the appliance around the air intake and exhaust,
as well as the blower is recommended. For heavy or continuous use, periodic
cleaning must be done more frequently. If the heater blows alternating cold and
warm air, check the blower for free movement and for debris restricting air flow.
If the blower does not move freely, the unit must be turned off and the blower
replaced immediately in order to prevent further damage to the unit.
WARNING
: Make sure all power to the appliance is turned OFF
before proceeding.
Printed in China
Troubleshooting
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Blower is not
spinning.
Blower is mak-
ing a loud noise.
1. There is no power to
the blower.
2. Blower is set to
AUTO " ".
3. Blower motor is bad.
1. Blower housing or
blades are dirty.
2. Blower rotation is
blocked.
3. Defective blower.
1. Clean blower and blower
housing.
2. Verify wiring is not in blower
path.
3. Replace blower.
1. Verify blower is plugged in and
set to MAN " " or
AUTO " ".
2. Allow 5-10 minutes for blower
to engage.
3. Replace blower.
10
33
This limited warranty is extended to the original retail purchaser of this heater and warrants against any
2
2
two
two
years
years
11
34
GHP Group, Inc.
6440 W Howard St
Niles, IL 60714-3302
Tel: (877) 447-4768
www.ghpgroupinc.com
GHP Group, Inc.
6440 W Howard St
Niles, IL 60714-3302