GFW MADRID WOODEN OTTOMAN BED 3FT Assembly Instructions Manual - User Manual

Full Text Searchable PDF User Manual

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

Size: 3FT L 2015 X W 995 X H 1140
Colour : WHITE,OAK

PLEASE READ

this sheet prior to assembly to familiarise yourself with the various stages of construction.

Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of
the packaging until you are certain that you have all the necessary parts for the assembly.

CAUTION

: There are small components used in the construction of this unit. These loose items should be kept away

from young children whilst assembling your unit to avoid the danger of choking hazards.

2632

Page 1 of 16

Tools Required

Thank you for purchasing the MADRID WOODEN OTTOMAN BED 3FT. Please read
the instructions carefully to ensure safe operation of the product.

IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

2632

Page 2 of 16

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

INFORMATION

•

This product is intended for a maximum person’s weight of 110kg . Do

not exceed this weight.

•

Due to the size of this product we recommend that it is assembled in the room

intended for use

•

When you are ready to start, make sure that you have the right tools, plenty of

space and a clean, dry area for assembly.

•

Unwrap all packaging materials and place the components on top of the carton

box or on a clean floor to prevent it from scratching

•

Check the pack and make sure you have all the parts listed

•

Ensure that this product is fully assembled and secured as illustrated before use.

•

Check all screws or bolts are tightened and inspect regularly

•

This product should only be used on firm, level ground

•

Please dismantle for transportation

•

Tools not included

WARNINGS

•

Keep small parts out of reach of children

•

Make sure the legs remain in contact with the ground

•

DO NOT use power tools to construct this product

•

DO NOT tighten screws until fully assembled

•

DO NOT over tighten screws or bolts

•

DO NOT use this product if parts are missing, damaged or worn

•

DO NOT stand on the product

•

This bed uses a pressured mechanism, always use caution when operating.

•

DO NOT remain on the bed whil

st the lifting mechanism is in use.

•

Only use the storage compartment when the frame is fully raised in the up

position.

•

Please pay particular attention when children or animals are present to ensure

that no accidental entrapment occurs whilst operating this product.

•

Keep hand and fingers clear of the mechanism when opening and closing the

bed for use.

•

Incorrect installation could lead to injury, take care following instruction.

•

Take care when adjusting positions to avoid trapping of body parts.

CARE INFORMATION

•

Never use scourers, abrasives or chemical cleaners.

•

To clean wipe with a sponge and warm soapy water. Do not use solvent based

cleaners or detergents as they can bleach or damage the product.

Please check the pack contents before assembling the product. If any components are missing, please contact your
retailer. The

ﬁ

ngs pack contains small items that should be kept away from small children.

2632
Page 3 of 16

(P13)

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

(P3)

(P9)

(P8)

(P11)

(P12)

(P8)

(P9)

(P2)

(P4)

(P5)

(P7)

(P6)

(P10)

(P1)

SIDE TUBE
2PCS
Carton No: 3

HINGE
2PCS
Carton No: 3

PISTON
2PCS

Carton No:

2632
Page 4 of 16

FRONT TUBE
1PC
Carton No: 3

CENTRE TUBE
1PC
Carton No: 3

BACK TUBE
1PC
Carton No: 3

LEFT

RIGHT

HEADBOARD
1PC
Carton No:1

FOOTBOARD
1PC
Carton No: 2

SIDE RAIL
2PCS

Carton No:

Parts

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

HOLDING TUBE
2PCS
Carton No: 3

WOODEN SLAT
13PCS
Carton No: 3

P13

HOLDING BLOCK
1PC
Carton No: 2

MATTRESS STOPPER
2PCS
Carton No: 2

P10

P11

P12

2632

Page 5 of 16

Parts

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

NON-WOVEN FABRIC
1PC
carton no:2

P14

2632
Page 6 of 16

Ref

Qty

Dimensions

H11

100

120

110

JCBC SCREW M6 X 80MM

JCBC SCREW M6 X 45MM

JCBC SCREW M6 X 15MM

BARREL NUT M6 X 16MM

DOWEL M10 X 30MM

Fixings (to scale)

WOOD BUTTON 8MM

(Not to scale)

Ref

Qty

Dimension

H10

PLASTIC END CAP

BELT

CORNER BRACKET

ALLEN KEY M4

CAUTION: There are many small components used in the construction of this product. Please keep these
componants away from young children whilst assembling this product.

If you keep the fittings in a bowl during assembly you will be less likely to lose them

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

2632

Page 7 of 16

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

Hints and Tips

To operate the ottoman, always use 2 hands at arm's length and only where illustration on this
product. You must ensure the mattress is on the bed frame before lifting the mechanism.

Failure

to do so may result in injury.

To ensure your safety please do not stand too close in case the frame bounces up. The weight of
the mattress loaded on the frame will keep the frame in a lower position until it is pulled upwards
by the user.

If removing the mattress, make sure the frame is secured so it does not flip open. When lifting the
bed frame, remove pillows and covers.

PLEASE NOTE

- It takes a lot of force to make the initial movement of the ottoman –

THIS IS A

DESIGN FEATURE OF THE PRODUCT SO THAT IT DOES NOT FALL SHUT

- and the nearer

to being closed the ottoman is, the easier it is to move. When the ottoman is almost shut, it will
close completely under its own weight.

When lowering the slat unit for the first time, take care to make sure it does not rub unevenly on
the inside face of the Side Rail. If it does, the bed has been assembled slightly out of square. This
can be rectified by moving the Footboard of the bed slightly to the left or right whilst leaving the
headboard

of the bed frame stationary.

Tip for difficulty with compression:

If you are experiencing difficulty with the initial compression try fitting one piston at a time
(following the Assembly Instructions) then press down on the side of the frame with the piston
fitted - this acts like a big lever (The weight of the mattress can be used to supplement the load
exerted). Effectively you are doubling the amount of force applied, because you have halved the
resistance offered by the pistons. It can take slightly more effort than you might feel comfortable
applying to the bed frame at first.

2632
Page 8 of 16

Do not attempt to move the bed whilst the frame is in the upright positon

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

2632

Page 9 of 16

2 people are required to fit the frame safety.

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

2632
Page 10 of 16

Lay out all 4 sides on a soft surface i.e. Rug, Carpet or Packaging Carton

STEP 1

STEP 1 X 2

Parts
Required

(H2)
JCBC SCREW
M6 x 45MM - 4pcs

(H3)
JCBC SCREW
M6 x 15MM - 8pcs

(H6)
M4 Allen Key - 1pc

2632
Page 11 of 16

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

(P3)
Side Rail - 2pcs

(P8)
Hinge - 2pcs

(P9)
Piston - 2pcs

(P12)
Holding Tube - 2pcs

(H6)

(H3)

(H6)

(P8)

(A)

(B)

(C)

(P8)

(P3)

(P12)

(P9)

(H2)

STEP 2

Parts
Required

STEP 3

Parts
Required

(H2)
JCBC SCREW
M6 x 45MM
- 2pcs

(H3)
JCBC SCREW
M6 x15MM
- 8pcs
(H6)
M4 Allen Key
- 1pc

(H8)
Corner Bracket
- 4pcs

(P3)

(P1)

2632

Page 12 of 16

(H6)

(H8)

(H3)

(H2)

(P2)

(P11)

(H6)

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

(P1)
Headboard
- 1pc
(P2)
Footboard
- 1pc
(P3)
Side rail
- 2pcs
(P11)
Holding Block
- 1pc

(p3)

(p1)

(H5)

(H4)

(p3)

(p1)

(p3)

(p2)

(H1)

(H11)

Screw Driver

(H4)

(H1)

(H1)
JCBC SCREW
M6 x 80MM
- 8pcs

(H5)
DOWEL
M10 x 30MM
- 16pcs

(H11)
Wood Button
- 8pcs

(H4)
BARREL NUT
M6 x 16MM
- 8pcs

(P1)
Headboard
- 1pc

(P2)
Footboard
- 1pc

(P3)
Side rail
- 2pcs

STEP 5

Parts
Required

2632
Page 13 of 16

(H3)
JCBC SCREW
M6 x15MM
- 6pcs

(H6)
M4 Allen Key
- 1pc

(P14)
Non-Woven Fabric
- 1pc

STEP 4

Parts
Required

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

(P4)
Front tube - 1pc
(P5)
Back tube - 1pc
(P6)
Centre tube - 1pc
(P7)
Side tube
- 2pcs
(P10)
Mattress stopper
- 2pcs

(H3)
JCBC SCREW
M6 x 15MM
- 12pcs

M4 Allen Key
-1pc
(H10) Belt
- 1pc

(P7)
side tube
- 2pcs

(P8) hinge
- 2pcs

(P4)

(P5)

(P6)

(P7)

(H10)

(H3)

(H6)

Bracket

( II )

(H6)

(H3)

(P10)

( III )

(H6)

(P6)

( I )

(H6)

(P14)

( I )

(H3)

(H6)

( II )

STEP 7

Parts
Required

2632
Page 14 of 16

(H9)
Plastic End Cap
- 26pcs

(P6) centre tube
-1pc

(P7) side tube
-2pcs

(P13)
Wooden Slat
- 13pcs

(P13) Wooden Slat
- 13pcs

(H9)
Plastic End Cap
- 26pcs

STEP 6

Parts
Required

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

(H9)

(P13)

1st

2 rd

(P7)

(P6)

(P13)

2632
Page 15 of 16

Complete Assembly

Your bed frame is now completely assembled but the ottoman will not operate correctly unless a mattress
is placed on the slat frame and will not stay shut unless the mattress remains in position. To position
the mattress on the slat frame, simply place the mattress on top of the slate frame whilst it is in
the up (open) position.

Lift with the strap (H10) and close with the strap. The strap should always be accessible. Take care
not to lean over the bed when lifting, if the mattress is thin and light, the frame may rise quickly. The

metal frame.

PLEASE NOTE - It take a lot of force to make the initial movement of the ottoman-THIS IS A
DESIGN FEATURE OF THE PRODUCT SO THAT IT DOES NOT FALL SHUT - and the nearer
to being closed the ottoman is, the easier it is to move. When the ottoman is almost shut, it will
close completely under its own weight.

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the end of connectors are tight and secure.

Keep instructions for future reference

2632
Page 16 of 16

MADRID WOODEN OTTOMAN BED 3FT ASSEMBLY INSTRUCTIONS

Ask a Question ?