GENUS Spectra Instruction Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

INSECT LIGHT TRAP SYSTEM

Instruction Manual

Covers Models:

Genus

Spectra & Genus

Spectra Compact

2/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

3/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

Item No.

Description

Front Screen

Lamp Holder

Control Board

Lamp

Lamp Clip

Table Stand

SPECTRA

SPECTRA
COMPACT

4/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

Grounding Instructions

THE UNIT IS EQUIPPED WITH AN APPROPRIATE 3-CONDUCTOR
CABLE AND 3-PRONG GROUNDING TYPE PLUG TO FIT THE
PROPER GROUNDING TYPE RECEPTACLE.
TO REDUCE THE RISK OF AN ELECTRIC SHOCK, THE PLUG
MUST BE PLUGGED INTO AN APPROPRIATE OUTLET THAT IS
PROPERLY INSTALLED AND GROUNDED [SEE DIAGRAM
BELOW]:

CONSULT A SUITABLY QUALIFIED ELECTRICIAN IF THE
GROUNDING INSTRUCTIONS ARE NOT COMPLETELY
UNDERSTOOD OR IF IN DOUBT AS TO WHETHER PROPER
GROUNDING EXISTS.

EXTENSION CABLES ARE NOT TO BE USED WITH THIS UNIT.

SAVE THESE INSTRUCTIONS

SPECTRA

5/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

Safety Instructions

CAUTION:

THE UNIT IS INTENDED FOR COMMERCIAL INDOOR USE ONLY AND
NOT TO BE USED WHERE IT MAY BE EXPOSED TO WATER, INCLUDING
ROOFED, BUT OPEN PORCHES OR IN WET LOCATIONS [E.G. ABOVE
COOKERS OR IN STEAM ROOMS].
THE UNIT IS NOT CONSTRUCTED FOR USE OUTDOORS AND TO AVOID
THE RISK OF FIRE OR ELECTRIC SHOCK IS THEREFORE NOT
SUITABLE FOR USE IN BARNS, STABLES AND SIMILAR LOCATIONS.

WARNING: SHOCK HAZARD. DO NOT OPEN WHILST CONNECTED TO
THE ELECTRICAL SUPPLY. NO USER SERVICEABLE PARTS INSIDE.
REPLACING THE CONTROL BOARD AND LAMPS MAY BE PERFORMED
BY THE USER. ALL OTHER REPAIRS AND MAINTENANCE MUST BE
PERFORMED BY QUALIFIED PERSONNEL ONLY.
TO MAXIMISE EFFICIENCY AND SAFETY, REPLACE CONTROL BOARD
CONTAINING INSECTS AS NEEDED.
STORE THE UNIT INDOORS WHEN NOT IN USE

THE UNIT MUST BE KEPT OUT OF REACH OF CHILDREN
THIS  UNIT  IS  NOT  INTENDED  FOR  USE  BY  PERSONS  (INCLUDING
CHILDREN)  WITH  REDUCED  PHYSICAL,  SENSORY  OR  MENTAL
CAPABILITIES,  OR  LACK  OF  EXPERIENCE  AND  KNOWLEDGE,  UNLESS
THEY

HAVE

BEEN

GIVEN

SUPERVISION

INSTRUCTION

CONCERNING USE OF THE UNIT BY A PERSON RESPONSIBLE FOR
THEIR SAFETY. CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT
THEY DO NOT PLAY WITH THE UNIT.
TO MAXIMISE SAFETY DISCONNECT THE UNIT FROM THE
ELECTRICITY SUPPLY WHEN NOT IN USE, BEFORE SERVICING, WHEN
CHANGING LAMPS AND CLEANING. REFER TO SERVICING
INSTRUCTIONS FOR METHOD AND FREQUENCY OF SERVICE.
DO NOT ABUSE THE POWER CABLE - NEVER CARRY THE UNIT BY THE
CABLE OR PULL IT FROM THE RECEPTACLE. KEEP THE CABLE FROM
HEAT, OIL, AND SHARP EDGES.
IF CABLE IS DAMAGED DO NOT USE. HAVE THE CABLE REPLACED BY
A QUALIFIED ELECTRICIAN.
DO NOT INSERT FOREIGN OBJECTS INTO THIS UNIT.
THE UNIT IS NOT TO BE USED IN LOCATIONS WHERE FLAMMABLE
VAPOUR OR EXPLOSIVE DUST IS LIKELY TO EXIST.
TO PROVIDE CONTINUED PROTECTION AGAINST THE RISK OF
ELECTRIC SHOCK, CONNECT TO PROPERLY GROUNDED OUTLETS
ONLY.

6/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

INTRODUCTION

Please read these instructions, follow them carefully and keep them for future
reference. The unit, when properly installed and maintained, will operate
safely and reliably for many years.

TYPE OF UNIT

The

Genus

Spectra

range consists of 2 models; a 2 lamp unit, a 1 lamp unit.

Both models use the same Control boards. Lamp types are PL36W UV-A .

UNPACKING

Each unit is carefully packed before leaving the production factory to ensure
arrival in perfect working order. Please be sure to remove all packing from
around and within the unit before installation.

LOCATIONS
1.

The extent to which insects are attracted to

Genus

Spectra

depends

largely on the intensity of other light available, whether daylight, or artificial
light, keep the unit switched on 24 hours.

Mount the unit within 1-1.5m (3-

5’) of the floor whenever possible.

Note. If mounting vertically, ensure lamp holders are at the top of the unit.

To comply with current Health and Safety legislation, ensure that safe and
appropriate access to the unit for maintenance and cleaning is available.

Place the unit as far as possible from windows (to minimise competition
from sunlight) and any other competing light sources.

Do not place the unit directly over exposed foods, food preparation
surfaces or packing lines.

Do not hang the unit over sources of heat or steam since this may
damage the insulation of the electric cables.

Place the unit out of reach of children whenever possible.

CONNECTION TO THE ELECTRICITY SUPPLY

The unit must be installed by a qualified electrician observing the following
instructions.

Check the input voltage on the unit label is correct for your electrical
supply.

Ensure that the circuit is fused at 3A maximum.

Connect the unit to the electricity supply by the cable provided which is
terminated in a plug connector. If this connector is incompatible with the
installation it must be cut off, rendered unusable, and disposed of.

Connection to the unit must be made using a cable type H05RN-F for
European models or cable type 3x18AWG SJT for North American
models. The cable supplied is of this type.

Connect the cable to the electricity supply ensuring that the colour code is
strictly followed [see table]:

7/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

Once connected, the cable should be mechanically secured to the wall using
proprietary cable clips.

CHANGING THE ELECTRICAL SUPPLY POWER CABLE

If the power cable is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.

INSTALLATION & FIXING

The unit can be wall mounted horizontal, vertical and across corner.

Temporarily fix the paper template to the selected position on the wall.
Ensure the holes to be drilled are level. Mark holes through, then remove
template.

For concrete walls, drill 3/16” (4.8mm) dia mounting holes.

Insert the four plastic anchors provided into holes and tap flush.
Insert the self tapping screws provided to within 1/8

” (3.2mm) of the wall.

For plasterboard walls use the aluminium anchors and machine screws
provided. For wood panel walls, locate wall studs and use only the self
tapping screws provided.

Hang the unit on the keyhole slots in the wall plate.

The unit can be table mounted using the Swivel stand located on the base

NOTE: Ensure that unit

can be both switched off and electrically isolated by

disconnection, for cleaning and maintenance.

LIVE

EARTH

NEUTRAL

BLACK OR
BROWN

GREEN OR
GREEN/YELLOW

WHITE OR BLUE

Corner Vertical
Wall Mount Holes

Corner Horizontal
Wall Mount Holes

Plastic Anchors

Aluminium Anchors

Use Self Tapping Screws for Plastic Anchors.
Machine Screws in Aluminium Anchors.

FIXING DETAILS

8/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

LAMP REPLACEMENT

Even though the amount of visible light emitted from the lamps does not
appear to change, the output of UV light diminishes with time. To maintain
efficiency, lamps must be replaced annually. Do not use UV-B or UV-C lamps.
The replacement lamps are available from your local distributor. To replace
the lamps, follow the procedure below:

Isolate/disconnect the unit from the electrical supply before handling.
Removing lamps from the unit prior to disconnection may cause the
circuitry of the unit to switch to safety mode. See reset instructions.
Open the front screen by lifting up and open to its full extent.
Lamps may be warm; it is advisable to wait a few minutes until cool.

Press the red button on the quick release lamp holder and pull the lamp
out and away making sure to carefully disengage from the lamp clip at the
opposite end. See diagram.

To install new lamps, position the lamp base flush against lamp holder so
the 4 pins are aligned with the slots and click securely into place. Push the
lamp into the clip at the opposite end.

Close the screen and reconnect the electrical supply.

WARNING: LAMPS CONTAIN MERCURY. DISPOSE OF ACCORDING TO
LOCAL, STATE OR FEDERAL LAW. SEE

WWW.LAMPRECYCLE.ORG

Lamp Holder

Lamp Clip

Control Board Tabs

Lamp

Control Board

9/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

CONTROL BOARD REPLACEMENT:

The

Genus

Spectra

fly trap uses the universal control board which is

available from your local distributor.

1. Prepare the replacement universal control boards [see following

diagram].

Genus

Spectra

: Two halves of the complete universal control board are

used. Tear off and discard section 4. Use one half of each board in the
upper and lower sections.

Genus

Spectra Compact

: Only one half of the complete universal

control board is used in. Tear off and discard section 4. Use one half of
the board and keep the remaining half for future use.

To replace the control board, follow the procedure below:

Isolate unit from electrical supply before handling.

Open the front screen by lifting up and open to its full extent.

Remove the control board by gripping the tab at the base of the board,
lifting up and off the plate.

Take the replacement control board and refit ensuring it locates behind
the tabs of the plate. Remove the release paper.

Close the screen and reconnect the electrical supply.

10/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

IMPORTANT SERVICING INSTRUCTIONS

For proper operation the interior and exterior surfaces of this unit should be
cleaned once per month or as needed. Excessive grease and food particles
will reduce its effectiveness as well as create an unsanitary condition.

For the best results the control boards should be replaced monthly. If there
is high insect activity control boards may need to be replaced more
frequently.
The units are easier to clean if maintained often.

Isolate unit from electrical supply before handling.

Wipe the unit with a damp cloth.

Change the control board every month or as needed.

Change the lamps every 12 months.

Reconnect electrical supply.

NOTE:  ISOLATE/DISCONNECT  THE  UNIT  FROM  THE  ELECTRICAL
SUPPLY BEFORE SERVICING.
REMOVING  LAMPS  FROM  THE  UNIT  PRIOR  TO  DISCONNECTION  MAY
CAUSE THE INTERNAL CIRCUITRY TO SWITCH TO SAFETY MODE.

LAMP MAINTENANCE

If either or both lamps glow dark purple (indicating a burned out lamp):
Follow the procedure for replacing lamps.

If both lamps are not glowing (no illumination at all):
Follow the procedure for resetting the lamp circuit.

The electronic circuit in the unit has a safety mode which temporarily shuts
down the unit when an electrical surge occurs; this feature protects service
personnel and the integrity of the unit.
Units in shut down safety mode may appear to be defective or may give the
false impression that the lamps are burned out.

11/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

Common causes;

1. Lamps are replaced without first disconnecting the unit from the electrical
supply.
2. Unit is exposed to extreme wet conditions.
3. Electrical supply power surge occurred in the building.

The unit must be reset to resume normal operation.

RESETTING THE LAMP CIRCUIT

If lamps do not light after replacement, reset the circuit as follows:
Isolate/disconnect the unit from the electrical supply.
Wait for 15 seconds, a faint glimmer may occur in either or both lamps
indicating the circuit has reset.
Reconnect the unit to the electrical supply.

ACTION IN CASE OF FAILURE

In the unlikely event of failure, should the lamps fail to light please have the
supply circuit and fuses checked by a qualified electrician.
If the lamps and electrical supply are in order but the unit still does not
function, please contact the local distributor.
Your local distributor will be able to supply any parts and replacement UV
lamps.

SAFETY

All

Genus

Spectra

units are certified to European Safety Standards

EN60335-1 and EN60335-2-59 recognised by BSI, KEMA, VDE, NEMKO,
DEMKO and SEV, Australian Safety Standards; OCEI, and North American
Standards; UL153, CSA C22.2-189 etc.
These standards institutions are recognised throughout the world for setting
the strictest controls over safety and efficiency.

12/12: ACC673-044 Revision: 5.0

Unit 29 Navigation Drive, Hurst Business Park, Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911 Email: sales@b-one.com Web: www.b-one.com

For Technical Support call the main number, fax or email: technical@b-one.com

Manufactured in the UK by:

29 Navigation Drive, Hurst Business Park,

Brierley Hill, West Midlands, DY5 1UT, United Kingdom

Tel: +44 (0)138 447 2900 Fax: +44 (0)138 447 2911

www.b-one.com / www.biting-insects.com

For technical support email technical@b-one.com

Ask a Question ?