PDF User Manual

  1. Home
  2. Manuals
  3. GENI MOVING HEAD OBY-5 User Manual

GENI MOVING HEAD OBY-5 User Manual

Made by: GENI
Type: User Manual
Category: Flood Light
Pages: 19
Size: 3.57 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

WWW.BEGLEC.COM

Exclusive Distribution:

 


background image

 


background image

1

 


background image

Description of the appearance

2

 


background image

Inspection

Carefully unpack the carton, and make sure if any damage or loss 
caused by transportation.

Contact your Geni dealer to assure your right by telephone or 
facsimile immediately if damage has occurred or if something is 
missing.

Packing List:

A. OBY-5 Moving Head
B.Operating Manual
C.
D.GOBO
E. Lamps (

Optional

)

Bracket

3

 


background image

Safety instructions

This appliance must be earthed (grounded).

Disconnect power before removing covers or servicing.

Keep case closed while operating.

OBY-5 contains no user serviceable parts. Refer servicing to 
qualified technicians only.

Lamp and components become hot during operation. Allow time to 
cool before handling.

Keep flammable material at least one meter away from unit.

Do not operate in wet conditions or near liquids.

Keep air vents clear to avoid overheating.

Lamp produces hazardous UV light. Do not look directly at lamp 
when lit.

Replace any blown or damaged fuses only with those of identical 
values.

4

 


background image

  Lamp Installation

5

When replacing the lamp, please wait 15 minutes after powering down to allow the 
unit to cool down! Always disconnect from main power prior to lamp replacement.

Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, 
clean the lamp with alcohol and wipe it with a lint free cloth before installation.

Warning!

2

S3

3,4

5

N

 

 

 

1

1

S1

2

S2

1.Keep projector-head upward .Unscrew 
   thumbscrews (S1) to detach the top 
   cover.

2. Unscrew screws (S2) to remove lamp 
    cover and expose lamp compartment.

3. If installing a new lamp, loosen both   
    screws on the double ended lamp to 
    allow for the lamp to slide into the 
    lamp socket slots. Lower lamp 
    evenly.

4. If replacing a lamp, loosen both lamp 
    screws (S3) to relieve tension from 
    lamp socket slots so you can slide the 
    lamp freely, upwards and out of lamp 
    socket. Raise lamp evenly to remove.

5. Before you tighten the lamp end 
    screws, rotate the bulb until the nipple 
    on the envelope (N) of the bulb is facing 
    upwards as illustrated.

6. If you are replacing the lamp, you may 
    want to log the fixture hours in order to 
    track the lamps use. Navigate to the 
    (LPti)on the menu display to obtain this 
    information. 

 


background image

a

a

d

OBY-5 can be set on the flat stage floor directly or use clamp to mount on 
any kinds of trusses for fitting the mobility of various venues.

Mount two attached brackets(a) on the bottom (See Figure ), and 
collocate the appropriate clamps(b) to rig with trusses. Must use the 
safety ropes that can hold the ten times as heavy as the fixture through 
the eye bolts(c) on the bottom of the base and trusses; then join the 
safety ropes with screw-on carabines(d).

Rigging:

6

 


background image

Linking

Use 3-pin XLR data cables to link the controller to DMX lighting 
equipment.

3-pin XLR connectors are follows:

Building a serial DMX-chain:

Connect the DMX output of the first fixture with the DMX input of the 
next fixture. And execute all the setups following the above-
mentioned instruction.
Flip the DIP SWITCH #3 of last fixture to  ON  position for terminal 
confirmation.

1

2

3

1

2

3

1:Ground 
2:Signal(-) 
3.Signal(+)

1:Ground 
2:Signal(-) 
3.Signal(+)

DMX-output 

XLR mounting-socket:

DMX-input 

XLR mounting-plug:

Connection with the mains

Connect the device to the mains with the power-plug.

The occupation of the connection-cables is as follows:

The earth has to be connected! In general, lighting effects should not
 be connected to dimming-packs.

7

 

 

 

 

 

 

 

 

 

 

 

 

 


background image

Instructions for  gobo replacement

Pl ea se cho os e the sui tab le go bo di men sion s of thi s fixtur e. (App en di x A)

3.Push GOBO & the spring ring out with the 
   fingers carefully.  (*Caution: Avoid falling 
   the spring ring into the fixture.)

2.Turn the open (circle) of the GOBO wheel to  
   "U"  shape gap in order to extract the rotating 
   GOBO easily. 

Rotating GOBO wheel

1.Open the top cover (*Refer to the steps of lamp installation.), and 
    loosen the screws with appropriate tools then extract  A . (See the 
    figures below.)

4.Insert the new GOBO and the spring ring (*Press the spring ring 
   tight with the appropriate tools in order to keep GOBO compact), 
   put  A  back and screw up the top cover.

Fixed GOBO wheel

The instructions are the same as changing the rotating GOBO; only 
winkle the spring ring out with appropriate flat screw driver before 
push GOBO out.

DANGER!
Install the gobos with the device switched
off only.

 

Unplug from mains before!

!

A

8

 


background image

DMX Channel chart

0-255

Gradual adjustment of the dimmer intensity from 0 to 100 %

Channel 1 - Dimmer intensity

Open/white
Steel Blue
Orange
Green Blue
Bright Blue
Bright Pink
Red
Deep Blue
Yellow
Dark Pink
Moss Green
Light Blue
Color wheel rotation slow to fast

13   
27   
41   
55   
69   
83   
97   
111   
125   
139   
153   
167   
255   

0

14
28
42
56
70
84
98

112
126
140
154
168

Channel 3 - Color wheel 1

Function of the control channels - 16 bit protocol

9

Channel 2 - Shutter, Strobe

 


background image

Open/white
Steel Blue
Rose Pink
Yellow
Pale Blue
C.T Orange
Pale Blue- C.T Orange
Steel Blue-Orange
Green-
Rose Pink-Moss Green
Rose Pink-
Yellow-Moss Green-Orange-Steel Blue
Color wheel rotation slow to fast

13   
27   
41   
55   
69   
83   
97   
111   
125   
139   
153   
167   
255   

0

14
28
42
56
70
84
98

112
126
140
154
168

Yellow

Yellow-Steel Blue-Green

Channel 4 - Color wheel 2

Channel 5 - Fixed gobo wheel 

Channel 6 - Rotating gobo wheel 

Channel 7 - indexing &  Rotating gobo  rotation

Rotating gobo angle 

zero to 360 degrees.  

adjustment from 

 

Forwards gobo rotation from fast to slow
Backwards gobo rotation from slow to fast

127   
191   
255   

0

128
192

10

 


background image

11

Channel 8- Prism-wheel

Open position
Triple prism static 
Triple prism  f

orwards rotation from fast to slow

Triple prism  b

ackwards rotation from slow to fast

Triple prism static 

1  
7   
132  
253   
255 

0
2
8

133
254

Channel 9- Iris

Closed

Min. Diameter to max. diameter
Iris-in from slow to fast
Iris-out  from fast to slow

Open

159   
207  
253   
255 

0

1

160
208

Iris-in

Iris-out

Channel 10- Focus

Focus adjustment from far to near

255 

0

Channel 11- Pan reguration

CH-11 

 

 The 

head

 of the unit is allowed to turn horizontally from 

             zero to 570 degrees.

253

CH-11 

 

 The 

head

 of the unit is allowed to turn horizontally from 

             zero to 570 degrees.

254 

254 -255

 


background image

Channel 16- Lamp switch

Standby
Lamp "on" 3 seconds later
Standby
Lamp "off" 3 seconds later
Standby

47 
95 
159 
207
255 

0

48
96

160
208

Channel 12 Tilt reguration

The 

head

 of the unit is allowed to turn vertically from 

zero to 270 degrees

Channel 13 Pan fine-tune  

While rotating horizontally the 

head

 is allowed to be 

fine tuned from zero to 2.2 degrees.

Channel 14 Tilt fine-tune  

While rotating vertically the 

head

 is allowed to be

 fine tuned from zero to 1 degree.

12

Channel 15 - Control 

CH 12

 


background image

13

 Channels arrangement

 


background image

Control Board

14

 


background image

15

Maintenance

Refer maintenance to qualified technicians. Please disconnect power 
and signal wire before maintaining fixtures.

In order to preserve OBY-5 in good condition, keep the routine 
maintenance by following date.

The steps are as follows:

The dichroic colour-filters, the metal gobo-wheel, the internal lenses 
and cooling fans should be cleaned with soft brush monthly.

The interior of the fixture should be cleaned at least half-yearly using 
a vacuum-cleaner or an air-jet.

Caution:

 Be careful not to damage the interior mechanical structures 

or circuits when using the air-jet.

To ensure a proper function and smooth rotation of the gobo-wheel, 
we recommend lubrication in six-month intervals.

Caution:

 Avoid the damage of interior structures when fixtures 

rotated, do not use excess lubrication.

Due to emit fog frequently, the optical lens and gobos would be oily; 
thus luminosity would be weak. We recommend using moist cloth or a 
trace of detergents to wipe them every two weeks. (Prohibit using the 
detergents consisted of alcohol and solvents.)

 


background image

Replacing the Fuse

If the fixture does not function, that may be the fuse was burned out. It 
may be time to replace the fuse of same type and specification for 
eliminating this fault.

Remove the electric power and flip the switch to " off "  position before 
replacing the fuse.

Replace the fuse as follows:

Step 1: Unscrew the screw of the fuse holder on the housing  

counterclockwise with appropriate tools.

Step 2: Remove the broken fuse and then replace the new fuse.

Step 3: Reinsert and tighten the screw on the fuse-holder.

Step 4: Turn the power on for test.

Please contact with the dealer if the fixture still cannot work or the fuse 
burns out again.

Appendix A  

31 mm

31 mm

25 mm

GOBO Size

16

 


background image

17

Product Specifications

Physical

Dimension(L

×

W

×

H):       400

×

380

×

540mm

Weight:                              26kg

AC supply

AC input:                           Certified power cord with plug or without plug
Voltage:                             220V, 230, 240V 50/60Hz: 100V,120V 50/60Hz
Fuse:                                 AC 230V: 7A/250V      AC 100V~120V:15A/250V
Power Consumption:      800W

Control and programming

Signal pinout:                   pin 1 shield, pin 2 (-), pin 3 (+)
Setting and addressing: LED control panel
Protocol:                           USITT DMX-512
Pan/tilt resolution:           8 or 16 bit
DMX channels:                14-16
Signal input:                     3-pin XLR male
Signal output:                   3-pin XLR female

Source

Lamp:                                575W discharge
Base:                                 SFC10-4
Approved models:           Philips MSI-575/HR (1000 hr; 6000K)

                                           Philips MSI-575/2    (1000 hr; 6500K)

Control:                             Automatic and DMX remote on/off

Electromechanical effects

Color wheel 1:                 11 dichroic colors+white
Color wheel 2:                 11 dichroic colors+white
Fixed gobo wheel:           9 replaceable gobos+white
Rotating gobo wheel:      6 replaceable gobos+white
Gobo rotation:                  adjustable speed and position direction
Dimmer:                            0-100% linear dimmer
Strobe:                              1-7Hz fast flashing
Rotating 3-facet prism:   in/out variable speed and direction
Focus:                               2m-infinity
Iris:                                    Mini 4 -Max 15

°

°

Pan:                                   0 ~570

°

°

Tilt:                                     0 ~270

°

°

Wheel control:                  auto-electronic reset

Gobos

Metal gobo:                        Diameter:31 mm
                                           Maximum image diameter:25 mm
                                           Metal type:white iron

Glass gobo:                      Diameter:31 mm
                                           Maximum image diameter:25 mm
                                           Glass type:heat-resistant and intensify glass
                                           Glass coating:dichroic