Full Text Searchable PDF User Manual
User's manual
GPS Radar Detector GENEVO GPS+
Main functions of Genevo GPS+?
Genevo GPS+ was designed to detect built-in radars via GPS module and it is possible to connect it
wirelessly with built-in radar antenna Genevo HD+. Genevo GPS+ is designed to protect the driver
from speeding fines. GPS+ communicates with driver in English language and its main functions
are detection of stationary radars, red light cameras and section speed cameras. In combination
with Genevo HD+ you can detect even microwave radars (X / K / Ka narrow bands) and laser guns.
Notifications:
Text warning and voice alert appears on Genevo GPS+ during radar alert. Strength of the signal
and beeps expresses the intensity of the received signal. Signal strength has ten levels. GPS alerts
are reported by voice. For example “Speed Camera”.
Control:
1) Left button MENU / ON-OFF
Short press: You will enter into setup menu. During radar alert you will mute the volume. The next
alert will be reported again in the standard volume.
Long press: Turn ON / OFF Genevo GPS+.
2) Right button SENSITIVITY / ADD YOUR OWN GPS POINT
Short press: You can change volume of Genevo GPS+.
Long ress: During normal operation: Add your own GPS point. During alert: If you hold it during an
alert you will mark the place of false radar reporting so at a given point detector will be
suppressed during the next passage. If you suppress a false alert, detector will not detect radars in
radius of about 150 meters. Hold button during the "suppressed" radar alert and this listing will be
canceled. After next passage radar alert will be signaled normally.
Menu:
Press
left button
for enter into menu.
Press
left button
to go from one item to the next.
To complete this change, simply wait a few seconds without pressing a button. The unit will
display “Seting Completed” to confirm your selection.
Items in the menu are as follows:
Brightness:
Bright -> Dim -> Smart Dark -> Full Dark.
Sensitivity: (only if Genevo HD+ is connected): Highway / City / Auto City
Setting the speed in Auto City (item is present only if the sensitivity is set to Auto City): Through
Left button
you are selecting between speeds for editing (number indicates the speed below which
the detector will not respond to alerts. Right number indicates the speed below which the
detector will detect alerts like in City mode).
Right button
change the specific speed. For example
if detector is set up to “20” and “50” the detector will not alert on radars till you reach 20 km/h
speed. In the speed range from 20 to 50 km/h the detector will only respond to stronger radar
signals. Maximum sensitivity will be reached at the speeds above 50 km/h.
Setting City and Auto City sensitivity (entry is present only if the detector sensitivity is set to other
than Highway): Via
Left button
you can select radar band for editing. To change the signal level on
which the detector will start responding to radar signals use
Right button
.
The level of
suppression can be selected in the range 0-9. For example, when setting is X2 K2 and Ka2 the level
of detection in all bands are slightly decreased.
Display Mode
: Speed/Time, Speed/Voltage, Battery Voltage, Time, Speed, Compass
Auto Mute: On / Off: If it´s activated, after two seconds of ongoing alert the volume will be
reduced.
The minimum speed for signaling radar: Off, 10 km / h, 20 km / h, 30km / h ......... .. 130 km / h
X-Band: On / Off
K-Band: Wide / Narrow / Instant Only / Off
Ka-Band: Wide / Narrow / Off
Laser: On / Off
Startup sound: On / Off
GPS connect announce: On / Off
GPS warning distance: Normal (approx. 250m) / Farther (approx. 375m) / Farest (approx. 500m)
Setting local time
:
You can change time zone
Language: Český jazyk / Deutsch / English
Factory reset: For reset press
Right button
.
Delete all user points:
For deleting all user points press
Right button
.
Operating frequency:
GPS: SiRF STAR IV
With Genevo HD+ combination:
Ka narrow: 34,0GHz, 34,3GHz
(±120MHz)
Ka wide: 33.4 GHz ~ 36.0 GHz
K narrow: 24.125GHz (±70MHz)
K wide: 24.125GHz (±150MHz)
X band: 10.525GHz (±50MHz)
Laser: 904nm
Technical parameters:
Operating temperature:
-20 – +85 °C
Oprating voltage: 11 – 16 V
Energy consumption: 140mA
normal, 200mA max. (12V)
Dimensions: 68 * 108 * 28 mm
Database Updates:
Database update is recommended to check once in three months. Download the new database is
performed according to the instructions
while at
you can register and receive notifications of new and updated database to
your email.
Your Dealer:
Manual REV: 2014-11-26