GENESIS MOVE LED-MS20 R User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

GENESIS MOVE

LED-MS20 R

User Guide

Professional Entertainment Technology

TABLE OF CONTENTS

1. Safety

Instruction

2. Technical

Specification

3. How To Set The Unit

4. How To Control The Unit

5. Troubleshooting

6. Fixture

Cleaning

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there is no flammable materials close to the unit while operating as it is fire

hazard.

Use safety cable when fixes this unit. Don’t handle the unit by taking its head only, but

always by taking its base.

Maximum ambient temperature is ta: 40

℃

. Don’t operate it where the temperature is

higher than this.

Unit surface temperature may reach up to 85

℃

. Don’t touch the housing bare-hand during

its operation. Turn off the power and allow about 15 minutes for the unit to cool down

before replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

Do not touch any wire during operation as high voltage might be causing electric shock.

Warning

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

Do not open the unit within five minutes after switching off.

Please read carefully the instruction, which includes important information

about the installation, usage and maintenance.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

any repairs yourself. In the unlikely event your unit may require service, please contact

your nearest dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit

is firmly fixed to avoid vibration and slipping while operating. And make sure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the

weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

2. Technical Specification

•

The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together

in master/slave connection, as many as required and run by built-in program chase

sequences automatically or by sound activation through an internal microphone to create

an intelligent effect.

•

It can be operated by DMX 512 control or can be used as an individual unit without a

controller.

•

Features different preprogrammed chase patterns.

•

Please use a cable when connecting units together.

•

Accurate focusable optics system and ultra smooth stepping motors, Fan cooled.

•

Pan: 540 deg. Tilt: 270 deg.

•

Voltage

：

AC 120V~60Hz/230V~50Hz

•

Power consumption: 55W

•

Dimension: 248x 228 x 330 mm

•

Light Source: 1×20W LED

•

Weight: 5.6 kg

3. How To Set The Unit

3.1 Main Function

To select any of the given functions, press the

MENU

button up to when the required one is

showing on the display. Select the function by

ENTER

button and the display will blink. Use

DOWN

and

button to change the mode. Once the required mode has been selected,

press the

ENTER

button to setup or it will automatically return to the main functions without

any change after idling 8 seconds. To go back to the functions without any change press the

MENU

button. The main functions are showing below:

DMX 512 Address Setting

Press the

MENU

button up to when the

is showing on the display. Pressing

ENTER

button and the display will blink. Use

DOWN

and

button to change the DMX512 address.

Once the address has been selected, press the

ENTER

button to setup or automatically

return to the main functions without any change after 8 seconds. To go back to the functions

without any change press the

MENU

button again.

Show Mode

Press the

MENU

button up to when the

is showing on the display. Pressing

ENTER

button and the display will blink. Use

DOWN

and

button to select the

(show 1)

(show 2) or

(show 3) or

(show 4) mode. Once the mode has

been selected, press the

ENTER

button to setup or automatically return to the main

functions without any change after 8 seconds. To go back to the functions without any

change press the

MENU

button again.

Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.

Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.

Show 3 mode - Fixture is placed on the speaker, The spot is always projecting

to the audience’s direction; i.e in front of the stage. Pan movement angel (left to right to

left): 160°. Tilt movement angel: 90° (60° above horizon; 30° below horizon.)

Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in

front of the stage. Pan movement angel (left to right to left):160°. Tilt movement angel:

90° (vertically, front 75°; back 15°)

Slave Mode

Press the

MENU

button up to when the

is showing on the display. Pressing

ENTER

button and the display will blink. Use

DOWN

and

button to select the

(normal) or

(2 light show) mode. Once the mode has been selected, press the

ENTER

button to setup or automatically return to the main functions without any change

after 8 seconds. To go back to the functions without any change press the

MENU

button

again.

Sound Mode

Press the

MENU

button until the

is showing on the display. Pressing

ENTER

button

and the display will blink. Use

DOWN

and

button to select the

(sound on) or

(sound off) mode. Once the mode has been selected, press the

ENTER

button to

setup or automatically return to the main functions without any change after 8 seconds. To

go back to the functions without any change press the

MENU

button again.

Blackout Mode

Press the

MENU

button up to when the

is showing on the display. Pressing

ENTER

button and the display will blink. Use

DOWN

and

button to select the

(yes blackout) or

(no blackout) mode. Once the mode has been selected, press the

ENTER

button to setup or automatically return to the main functions without any change

after 8 seconds. To go back to the functions without any change press the

MENU

button

again.

Pan Inversion

Press the

MENU

button up to when the

is showing on the display. Pressing

ENTER

button and the display will blink. Use

DOWN

and

button to select the

(normal)

(pan inversion) mode. Once the mode has been selected, press the

ENTER

button to setup or automatically return to the main functions without any change after 8

seconds. To go back to the functions without any change press the

MENU

button again.

Tilt Inversion

Press the

MENU

button up to when the

is showing on the display. Pressing

ENTER

button and the display will blink. Use

DOWN

and

button to select the

(normal)

(tilt inversion) mode. Once the mode has been selected, press the

ENTER

button to setup or automatically return to the main functions without any change after 8

seconds. To go back to the functions without any change press the

MENU

button again.

Led Display

Press the

MENU

button up to when the

is showing on the display. Pressing

ENTER

button and the display will blink. Use

DOWN

and

button to select the

(Led on) or

(Led off) mode. Once the mode has been selected, press the

ENTER

button to setup or automatically return to the main functions without any change after 8

seconds. To go back to the functions without any change press the

MENU

button again.

Display Inversion

It is good for you to install the unit on the floor or under ceiling. Press the

MENU

button up to

when the

is blinking on the display. Use the

ENTER

button to change to the mode

(display normal), It will automatically store after 8 seconds. Or press the

ENTER

button again return to the mode

(display inversion). To go back to the functions

press the

MENU

button.

Display normal mode for the fixture putting on the floor.

Display inversion mode for the fixture fixing under ceiling.

Focus Adjust

Press the

MENU

button up to when the

is blinking on the display. Pressing

ENTER

button to change orientation of the light, then you can turn the plastic lens manually to adjust

the focus of the unit. To go back to the functions press the

MENU

button again.

Self-Test

Press the

MENU

button up to when the

is blinking on the display. Pressing

ENTER

button and the unit will run self-test by built-in program. To go back to the functions press the

MENU

button again.

Temperature Test

Press the

MENU

button up to when the

is blinking on the display. Pressing

ENTER

button and the display will show the temperature of the unit. To go back to the functions

press the

MENU

button again.

Fixture Hours

Press the

MENU

button up to when the

is blinking on the display. Pressing

ENTER

button and the display will show the number of working hours of the unit. To go back to the

functions press the

MENU

button again.

Software version

Press the

MENU

button up to when the

is blinking on the display. Pressing

ENTER

button and the display will show the version of software of the unit. To go back to the

functions press the

MENU

button again.

Reset

Press the

MENU

button up to when the

is blinking on the display. Pressing

ENTER

button and all channels of the unit will return to their standard position. To go back to the

functions without any change press the

MENU

button again.

3.2 Home Position Adjust

In the main functions, hold

Enter

button for at least 3 seconds into offset mode, use

DOWN

and

button up to chose

, pressing

ENTER

button and the display will

blink. Use

DOWN

and

button to adjust the home position of the tilt or gobo. Once the

position has been selected, press the

ENTER

button to setup, hold the

MENU

button for

about 3 seconds or wait for 8 seconds to back to the main functions without any change.

4. How To Control The Unit

You can operate the unit in three ways:

1. By master/slave built-in preprogram function

2. By easy controller

3. By universal DMX controller

No need to turn the unit off when you change the DMX address, as new DMX address

setting will be effected at once. Every time you turn the unit on, it will show

on the

display and move all the motors to their ‘home’ position and you may hear some noises for

about 20 seconds. After that the unit will be ready to receive DMX signal or run the built in

programs.

4.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the other units to

give an automatic, sound activated, synchronized light show. This function is good when you

want an instant show. You have to set the first unit in master mode

and select

(show 1) or

(show 2) or

(show 3) or

(show 4) mode. Its

DMX input jack will have nothing plugged into it, and Its master LED will be constantly on

and sound LED will flash to the music. The other units will have to set in slave mode

and select

(normal) or

(2 light show) mode, Their DMX cables plugged into

the DMX input jacks (daisy chain) and the slave led lights will constantly on.

2-light show

(slave mode),

means the unit works normally and

means

2-light show. In order to create a great light show, you can set

on the second unit to

get contrast movement to each other, even if you have two units only.

4.2 Easy Controller

The easy remote control is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit, you will find that the remote control on the first unit will

control all the other units functions press the MENU button again.

Stand By

Blackout the unit

Function

1. Sync. Strobe

2. Async strobe

3. Sound Strobe

Show

1-4

1. Press to select color

2. Hold to select gobo

Mode

Sound (LED OFF)

Show (LED

Slow Blinking)

LED ON

4.3 DMX Controller

An universal DMX controller to control the units, you have to set DMX address from 1 to 512

channel so that the units can receive DMX signal.

Press the

MENU

button up to when the

is showing on the display. Pressing

ENTER

button and the display will blink. Use

DOWN

and

button to change the

DMX512 address. Once the address has been selected, press and keep

ENTER

button pressed up to when the display stops blinking or storing automatically 8

seconds later. To go back to the functions without any change press the

MENU

button again. If you use please refer to the following diagram to address your

DMX512 channel for the first 4 units

：

10-

4.4 DMX 512 Configuration

4.5 DMX512 Connection

The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.

11-

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm

1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it

in the DMX-output of the last unit.

3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to

the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is

a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded

connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit,

when one of the units’ power is disconnected.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5. Troubleshooting

Following are a few common problems that may occur during operation. Here are

some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the unit or the previous one.

12-

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may

cause damage or interference to DMX interface circuit.

C. Some units don’t respond to the easy controller

1. You may have a break in the DMX cabling. Check the LED for the response of the

master/ slave mode signal.

2. Wrong DMX address in the unit. Set the proper address.

D. No response to the sound

1. Make sure the unit does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition

6. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater

accumulation of dirt on the unit’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

13-

EC Declaration of Conformity

We declare that our products (lighting equipments) comply with the

following specification and bears CE mark in accordance with the

provision of the Electromagnetic Compatibility (EMC) Directive

89/336/EEC.

EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

Innovation, Quality, Performance

Ask a Question ?