Full Text Searchable PDF User Manual
Built-in oven
Installation instructions
NZ AU
BI453 and BI603 models
Important!
To avoid hazard, follow these instructions carefully before installing or using this product.
Please make this information available to the person installing the product as it could reduce
your installation costs.
This oven is to be installed and connected to the electricity supply only by an authorised person.
Installation must comply with your local building and electricity regulations.
Failure to install the oven correctly could invalidate any warranty or liability claims.
Before you install the oven, please make sure that
A suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned
to comply with the local wiring rules and regulations. The switch must be of an approved
type installed in the fixed wiring and provide a 3 mm air gap contact separation in all poles in
accordance with the local wiring rules.
In Australia and New Zealand, a switch of the approved type with a 3 mm air gap must be installed
in the active (phase) conductor of the fixed wiring.
The location of the oven connection socket (if fitted) is outside the cavity if the product is flush to
the rear wall.
The electrician allows at least 1.5 m free length of connection cable within the cavity for ease of
installation and servicing of the product.
The mains cable should not touch any hot metal parts.
Note: the oven has a recess at the bottom rear to allow for the cable entry. The mains cable must
enter the cavity in this recessed area.
The cavity is completely sealed with no gaps.
This allows the cooling air to vent correctly, under
the oven and through the oven frame. If you do not seal the cavity, the surrounding cabinetry may
overheat and become damaged.
The benchtop and oven cavity are square and level, and are the required dimensions.
The height from the floor suits the user.
The oven door/s can open fully without obstruction.
When you install the oven
For ovens with cooktops, make sure that the controls connect to the correct heating elements.
Do not seal the oven or cooktop into the cabinetry with silicone or glue. This makes future
servicing difficult. Fisher & Paykel will not cover the costs of removing the oven or cooktop, or of
damage caused by this removal.
Fit the washers to the screws (supplied) and use them to secure the oven to the cabinetry. Do not
over-tighten the screws. You could damage the oven frame enamel.
Do not stand on the door, or place heavy objects on it.
Safety and warnings
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
1
Contents
Product and cabinetry dimensions
2
Installing the oven
6
Installing the cooktop
7
Important!
SAVE THESE INSTRUCTIONS
2
Product and cabinetry dimensions
Single oven models
A
B
C
E
D
F
G
H
J
K
L
Product and cabinetry dimensions
(mm)
BI453
models
BI603
models
A
overall height of product
450
595
B
overall width of product
595
595
C
overall depth of product
(without handle)
562
562
D
height of chassis
433
578
E
width of chassis
550
550
F
depth of chassis
542
542
G
depth of oven frame and control panel
(excl. knobs)
20
20
H
depth of oven door
(open) (measured from front of oven frame)
320
465
I
minimum inside width of cavity
560
560
I
I
overall width of cavity
600
600
J
inside height of cavity
438
583
J
I
overall height of cavity
455
600
K
minimum inside depth of cavity
550
550
L
flush fitting cabinetry clearance
20
20
Note: If installing a cooktop above the oven ensure adequate clearance is provided for the cooktop as per the
cooktop manufacturer’s instructions.
I
Installation diagrams for illustration purposes only
I
I
J
I
2.5 mm
16-20 mm
Ensure the cavity is completely sealed with no gaps
L
3
Product and cabinetry dimensions
Double oven models
Product and cabinetry dimensions
(mm)
BI603
2
models
BI603ED
BI603 1.5
models
A
overall height of product
1077
932
B
overall width of product
595
595
C
overall depth of product
(without handle)
562
562
D
height of chassis
1060
915
E
width of chassis
550
550
F
depth of chassis
542
542
G
depth of oven frame and control panel
(excl. knobs)
20
20
H
depth of oven doors
(open) (measured from front of oven frame)
465/465
465/320
I
minimum inside width of cavity
560
560
I
I
overall width of cavity
600
600
J
inside height of cavity
1065
920
J
I
overall height of cavity
1082
937
K
minimum inside depth of cavity
550
550
L
flush fitting cabinetry clearance
20
20
M
minimum clearance from floor to bottom of cavity
380
525
A
B
C
D
E
F
G
H
I
J
K
L
I
I
J
I
M
Ensure the cavity is completely sealed with no gaps
4
Product and cabinetry dimensions
Product and cabinetry dimensions
(mm)
BI603 CTE
models
A
minimum inside width of cavity
560
A
I
overall width of cavity
600
B
inside height of cavity
583
B
I
overall height of cavity
600
C
minimum inside depth of cavity
550
D
flush fitting cabinetry clearance
20
E
minimum clearance from benchtop surface to
top surface of oven chassis
55
Built-in oven/cooktop
combination
BENCHTOP
OVEN
Please refer to cooktop
installation instructions
p/n 599100
Dimensions as
per single oven
model BI603
B
C
D
A
E
E
B
A
I
B
I
Ensure the cavity is completely sealed with no gaps
5
Built-in oven/microwave
combination model
Product and cabinetry dimensions
B
C
D
H
J
A
E
F
G
H
K
L
M
I
Product and cabinetry dimensions
(mm)
B
I603 X
C
models
A
overall height of product
932
B
overall width of product
595
C
depth of microwave
(excl.frame and control panel)
455
D
depth of microwave frame and control panel
30
E
width of microwave chassis
558
F
depth of oven chassis
542
G
depth of oven frame and control panel
(excl. knobs)
20
H
depth of oven door
(open) (measured from front of oven frame)
465
I
depth of microwave door
(open)
440
J
minimum inside width of cavity
560
J
I
overall width of cavity
600
K
minimum inside height of cavity
935
L
minimum inside depth of cavity
550
M
flush fitting cabinetry clearance
20
J
I
Ensure the cavity is completely sealed with no gaps
545
6
Installing the oven
O
MM
1
2
3
4
5
6
7
Installing the cooktop
O
MM
1
2
3
4
5
6
Please refer to cooktop
installation instructions
p/n 599100
8
Copyright © Fisher & Paykel 2005. All rights reserved.
The product specifications in this booklet apply to
the specific products and models described at the
date of issue. Under our policy of continuous product
improvement, these specifications may change at any
time. You should therefore check with your Dealer to
ensure this booklet correctly describes the product
currently available.
www.fisherpaykel.com
NZ AU
Built-in oven installation instructions
Published: 08/2005
Part No. 542511 A