Enviroflex ENVIROMAC MAC1 Owner's Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

THE ENVIROMAC



MOBILE AIR CLEANER

MAC1

(107.1020)

OWNER’S MANUAL

In Canada:

Enviroflex



International Inc.

17 Brownridge Road, Unit 8

Halton Hills, Ontario

L7G OC6

Phone: (905) 636-1177

Fax: (905) 636-1178

Web Site:

www.enviroflex.com

Email:

info@enviroflex.com

In USA

Enviroflex



International Inc.

1051 Clinton Street

Buffalo, New York

U.S.A 14206-2823

Phone: (716) 883-2319

Fax: (716) 892-2139

Web Site:

www.enviroflex.com

Email:

info@enviroflex.com

April 26, 2012

ABOUT THE PRODUCT

PRINCIPLE OF OPERATION

The ENVIROMAC



Portable Air Cleaner is a

media type Air Cleaner operating on a two-stage
filtration  principle.  After  the  contaminant  is
picked  up  at  the  hood  of  the  Flexible  Arm  it  is
then drawn through the arm and through the fan
assembly and discharged to the inside part of the
high  efficient  washable  filter.  The  filtered  air  is
discharged  out  the  2  doors.  The  2  doors  contain
charcoal, which eliminates most gases that might
be  in  the  filtered  air  stream.  The  high  efficient
washable filter collects particulate only and does
not  filter gases,  which is  the sole purpose of the
charcoal door filters.

MAJOR COMPONENTS

The ENVIROMAC



Portable Air Cleaner is a

self-contained unit comprised of a flexible arm
(for source capture), fan and motor assembly,
high efficient washable filter, (2) carbon door
filters, complete cabinet housing and an
electrical compartment which also includes a
contactor overload.

A) HIGH EFFICIENCY HIGH EFFICIENT
WASHABLE FILTER

This  filter  is  a  high  efficiency  high  efficient
washable  filter.  The  suction  will  deteriorate  at
the  hood  as  the  filter  loads  up  with  particulate.
Eventually  the  filter  will  have  to  be cleaned. To
commence  cleaning  the  filter,  you  must  remove
the  door  at  the  front  of  the  machine  which  is
where the switch and nameplate are located. This
door  is  removed  by  removing  the  (2)  plastic
knobs  near  the  bottom  of  the  door  and  then
pulling  the  door  out  on  an  angle  so  the  door  is
free  from  the  (2)  welded  bolts.  Then  pull  down
on  the  door  to  let  it  slide  down  from  the  top  of
the door. You then remove the filter by lowering
the scissor jack with a ratchet. Then slide out the
cartridge  filter.  You  then  invert  the  filter  upside
down and utilize the existing gasket on the filter

to make a seal and take an air hose with about 80
P.S.I.  and  blow  the  filter  from  the  outside  to
remove all of the particulate that is on the inside
of  the  filter.  You  can  now  put  the  cleaned  filter
back  into  the  machine  and  tighten  the  filter  by
raising  the  scissor  jack.  Make  sure  the  filter  is
resting  on the back of the filter cradle butted up
against the tab locators. Make sure that the top of
the filter fits inside the top plate that has a 1” lip
on  it.  Make  sure the scissor jack is  high enough
to  allow  an  airtight  seal  on  the  top  of  the  filter
gasket. Caution should be taken not to apply too
much  pressure  to  the  filter  or  you  could  squash
the filter if too much pressure is applied. Always
blow  the  outside  of  the  filter  with  the  gasket  of
the filter either on the floor or a container to give
you  a  good  seal  so  that  the  dirt  does  not  escape
under the seal. Never blow from the inside as the
contaminant  will  blow  all  over  the  surrounding
area  and  will  also  force  the  very fine particulate
into  the  media.  Once  the  filter  is  installed  you
should  start  up  the  machine  and  feed  2  cups  of
Precoat  in  a  fine  mist  at  the  intake  of  the  hood.
The  Precoat  increases  the  filter  efficiency  of  the
washable  filter  and  acts  as  a  prefilter.  Once  you
complete  the  Precoat  process  you  can  now
commence welding.

B) CHARCOAL FILTERS

Both doors contain the charcoal filters. They
should be replaced 1 or twice a year in a normal
welding environment.

C) ELECTRICAL COMPARTMENT

The unit operates off 120 volts single phase
utilizing a 20-amp service outlet. The motor
draws about 17.5 amps under full load
conditions. There is a contactor and an overload
inside this compartment and the overload is set at
about 20% above the 17.5 amps. This will
automatically shut off power to the motor in the
event of an overload. This gives full protection to
the motor. The unit has a spring activated on/off
dual switch on the front of the panel. There are
facilities to put in an optional halogen light in the
hood of the arm. This requires a 120 Volt to 24-

volt step down transformer for this option. The
halogen light will run off of 24 volts AC.

C) CABINET

The cabinet is built of 14-gauge steel. There are
2 doors on the unit and the discharge of the clean
air is through these 2 doors.

D) BLOWER AND MOTOR SECTION

The motor is a 1.5 HP TEFC, 120/1/60, 3600
RPM. The fan is a high-pressure fan fabricated
out of 14 gauge metal.

E) ADDITIONAL EQUIPMENT FEATURES

The standard unit comes equipped with the
Snorkvac™ 10 Ft. flexible arm. The 3 articulated
joint sections could be adjusted to suit the
operator as to the ease of movement of the 4
different articulations. There is an optional 14 Ft.
Snorkvac™ flexible fume arm.

MAINTENANCE SCHEDULE

The filter should be cleaned or replaced when
there is inadequate suction at the hood. The
charcoal door filters should be replaced once or
twice a year. The arm has friction discs with
washers, which can be adjusted to suit the
operator. The unique design of the arm
minimizes any problems related to sagging, burn
holes in the hose and ease of arm movement.
This is a major problem with conventional less
expensive arms.

Thank you for purchasing your new
ENVIROMAC



Portable Air Cleaner. The air

in your work area will be much healthier to
breathe.

ENVIROFLEX



FOR A HEALTHIER WORK ENVIRONMENT

IN U.S.A.

ENVIROFLEX INTERNATIONAL INC.

1051 CLINTON ST.

BUFFALO NY, USA 14206-2823

TEL. (716) 883-2319 FAX (716) 892-2139

TOLL FREE 1-866-ENV-FLEX

Internet: http://www.enviroflex.com

Email: Info@enviroflex.com

IN CANADA

ENVIROFLEX INTERNATIONAL INC.

17 BROWNRIDGE RD. UNIT 8

HALTON HILLS, ONTARIO, CANADA, L7G 0C6

TEL. (905) 636-1177 FAX (905) 636-1178

TOLL FREE 1-877-ENV-FLEX

Internet: http://www.enviroflex.com

Email: info@enviroflex.com

ENVIROMAC



WARRANTY

The

ENVIROMAC



PORTABLE AIR CLEANER

carries a 1-year warranty.

-Parts are replaced at no cost. Labor charges are extra.
The Cartridge filter and carbon filters are guaranteed for a period of (30) days. The Company’s responsibility and obligation
under the guarantee is limited to the repair or exchange of any defective parts, which have been returned prepaid, to the
factory or an authorized service depot, and which prove to be defective through normal use. Only prepaid returns will be
accepted unless previously authorized to be returned freight collect. Goods repaired under warranty will be returned
prepaid. If in the company’s judgment the repair is not covered by the warranty, parts will be billed with a small labor charge
and returned collect.
The conditions of the Guarantee are:
1) The unit must have been operated within its listed capacity.
2) The unit must not have been moved from the site of its original installation.
3) The WARRANTY CARD must be returned within (10) days of installation. (Failing this, the company will guarantee the

unit for a period of 12 months from the date of manufacture according to the Company’s records.)

Please return warranty card to one of the following addresses:

In Canada:
Enviroflex International Inc.
17 Brownridge Road, Unit 8,
Halton Hills, Ontario
L7G 0C6
Phone: 905-636-1177
Fax: 905-636-1178

In U.S.A.:
Enviroflex International Inc.
1051 Clinton St.
Buffalo, N.Y.
14206-2823
Phone: 716-883-2319
Fax: 716-892-2139

ENVIROFLEX



FOR A HEALTHIER WORK ENVIRONMENT

IN U.S.A.

ENVIROFLEX INTERNATIONAL INC.

1051 CLINTON ST.

BUFFALO NY, USA 14206-2823

TEL. (716) 883-2319 FAX (716) 892-2139

TOLL FREE 1-866-ENV-FLEX

Internet: http://www.enviroflex.com

Email: Info@enviroflex.com

IN CANADA

ENVIROFLEX INTERNATIONAL INC.

17 BROWNRIDGE RD. UNIT 8

HALTON HILLS, ONTARIO, CANADA, L7G 0C6

TEL. (905) 636-1177 FAX (905) 636-1178

TOLL FREE 1-877-ENV-FLEX

Internet: http://www.enviroflex.com

Email: info@enviroflex.com

ENVIROMAC



Return Business Reply Card. Retain Warranty Card.

Owner’s Name_________________________________________________________________________

Address______________________________________________________________________________

City____________________________State/Province_______________Zip/Postal Code______________

Contact Name______________________________ Contact Email Address_______________________

Installing Contractor’s Name______________________________________________________________

Model No.______________________Serial No.___________________Date of Installation____________

Reasons for Buying:

1) Improved Air Quality

2) Welding Smoke Removal

3) Other____________________________

Where did you hear about

1) Newspaper or Magazine?

this unit?

2) Telephone Directory

3) Trade Directory

3) Enviroflex



Distributor

4) Friend

5) Another company

6) Trade Show

7) Other___________________________

ENVIROFLEX®

ATERIAL

AFETY

ATA

HEET

I. PRODUCT IDENTIFICATION

Trade Name: Envirocoat



Chemical Name: Amorphous siliceous mineral-silicate Formula: Sodium-potassium-aluminum-silicate of

variable composition

II. PRODUCT INGREDIENTS

Ingredient Name: Perlite, Expanded milled may contain Crystalline Silica Quartz less than 1.0% %: 100
Permissible Exposure: 5mg/m

TWA Respirable dust re: OSHA PEL

III. PHYSICAL DATA

Appearance and Odor: White/off white powder; odorless Boiling Point: N/A Evaporation Rate: N/A Vapor Pressure: N/A
Specific Gravity (water=1): 2.35 Water Solubility (%): Slight Melting Point: N/A Vapor Density: (Aim1): N/A; %
% Volatile by Volume: N/A

IV. FIRE AND EXPLOSION DATA

Flash Point (Method): Nonflammable Unusual Fire or Explosion Hazards: None Flammable Limits: N/A

Extinguishing Media: N/A Special Fire-Fighting Procedures: None Auto-ignition Temperature: N/A

NFPA Flammable/Combustible Liquid Classification: N/A

V. HEALTH HAZARDS A. Summary/Risks

Summary: OSHA considers Perlite a nuisance dust and recommends a PEL of 5 mg/m

TWA respirable dust. Inhalation over long

periods of high amounts of any nuisance dust may overload lung clearance mechanism and make the lungs more vulnerable to

respiratory disease.

Medical Conditions Which May Be Aggravated: Pre-existing upper respiratory and lung disease (such as bronchitis, emphysema,
asthma, or others).

Target Organ(s): Lungs Primary Entry Route(s): Inhalation Acute Health Effect: Transitory upper respiratory irritant.

Chronic Health Effects: See Summary. Follow the safe handling practices shown on the product bag label.

V. HEALTH HAZARDS B. Signs/Symptoms of Overexposure

Inhalation: Coughing, irritation of nose and throat; congestion may occur upon overexposure Skin Absorption: N/A

Skin Contact: N/A Ingestion: Not hazardous. Generally regarded as safe by the FDA. Eyes: Temporary irritation and/or inflammation.

V. HEALTH HAZARDS C. First Aid/Emergency Procedures

Inhalation: Remove from dusty area; drink water to clear throat; blow nose to evacuate dust. Skin Contact: N/A

Skin Absorption: N/A Ingestion: Not hazardous, generally recognized as safe by the FDA Eyes: Do not rub eyes. Flush eyes with
copious amounts of water to remove any dust particles. Consult a physician if irritation persists.

Vl. REACTIVITY DATA

Stability: Material is stable. Hazardous polymerization will not occur. Chemical Incompatibilities: Hydrofluoric acid

Conditions to Avoid: None in designed use. Avoid contact with hydrofluoric acid. Hazardous Decomposition Products: Reacts with
Hydrofluoric acid to form toxic silicon tetra fluoride gas.

Vll. SPILL OR LEAK PROCEDURES

Procedures for Spill/Leak: Vacuum clean or wet sweep; avoid dusting; use a dust suppressant when sweeping.

Waste Management:

Not considered as hazardous waste by RCRA (40 CFR Part 261). Place waste and spillage in closed containers.

Dispose in approved landfill. RQ-N/A

VIII. SPECIAL PROTECTION INFORMATION

Goggles: Normally not required. You may use safety eyewear to protect from dusts. Gloves: Normally not required. You may use

gloves to protect overly sensitive skin. Respirator: Even though Perlite is a nuisance dust, we recommend the use of NIOSH approved

respirators to protect against silicosis producing dusts. Ventilation: Use adequate exhaust ventilation and/or dust collection to keep
dust levels below PEL.

Special Considerations for Repair/Maintenance of Contaminated Equipment: Insure proper respiratory protection.

IX. SPECIAL PRECAUTIONS

Storage Segregation Hazard Classes: N/A

***ALWAYS SEGREGATE MATERIALS BY MAJOR HAZARD CLASS***

Special Handling/Storage: Store in dry place. Repair all broken bags immediately. Avoid creating dust. Maintain good housekeeping

practice. Special Workplace Engineering Controls: Adequate ventilation and appropriate local exhaust where needed to keep dust

levels below PEL. Other: Comply with all Federal, State and local regulations.

As of the date of preparation of this document, the foregoing information is believed to be accurate and is provided in good

faith to comply with applicable Federal and State law(s). However, no warranty or representation with respect to such

information is intended or given.

In U.S.A.:

Enviroflex International Inc.

In Canada:

Enviroflex International Inc.

1051 Clinton St.

17 Brownridge Road, Unit #8

Buffalo, NY, U.S.A. 14206-2823

Halton Hills, Ontario, Canada L7G OC6

Phone :(716) 883-2319 Fax:(716) 892-2139

Phone:(905) 636-1177 Fax:(905) 636-1177

Effective:

November 14, 2008

Section 2A

Country:

Canada

Page 1 of 1

ENVIROFLEX



FOR A HEALTHIER WORK ENVIRONMENT

IN U.S.A.

ENVIROFLEX INTERNATIONAL INC.

1051 CLINTON ST.

BUFFALO NY, USA 14206-2823

TEL. (716) 883-2319 FAX (716) 892-2139

TOLL FREE 1-866-ENV-FLEX

Internet: http://www.enviroflex.com

Email: Info@enviroflex.com

IN CANADA

ENVIROFLEX INTERNATIONAL INC.

17 BROWNRIDGE RD. UNIT 8

HALTON HILLS, ONTARIO, CANADA, L7G 0C6

TEL. (905) 636-1177 FAX (905) 636-1178

TOLL FREE 1-877-ENV-FLEX

Internet: http://www.enviroflex.com

Email: info@enviroflex.com

Precoat Instructions for ENVIROMAC



Filter

Prior To Initial Use

The cartridge filter has to be pre-coated with 2 cups of Precoat prior to initial use. The
precoat should be fed into the pickup hood at the end of the Snorkvac™ Arm. After pre-
coating the filter let the fan operate for two (2) minutes to allow the Precoat to settle on the
inside of the filter.

After Initial Precoat

The suction will deteriorate as the filter loads up with particulate. When it is time to clean the
filter you remove the filter, turn it upside down, blow it out on the outside with compressed
air  then  insert  back  into  the  machine  and  precoat  the  unit  the  same  as  the  initial  precoat
instructions.

The  filter  can  be  cleaned  with  water  as  the  media  does  not  retain  any  moisture.  However,
getting  rid  of  the  water  and  particulate  could  be  a  problem  as  people  are  concerned  with
dumping hazardous particulate down a drain.

You can dispose of the particulate in a bag if the filter was cleaned with compressed air.

Date:  November 14, 2008

Section 2B

ENVIROFLEX



FOR A HEALTHIER WORK ENVIRONMENT

IN U.S.A.

ENVIROFLEX INTERNATIONAL INC.

1051 CLINTON ST.

BUFFALO NY, USA 14206-2823

TEL. (716) 883-2319 FAX (716) 892-2139

TOLL FREE 1-866-ENV-FLEX

Internet: http://www.enviroflex.com

Email: Info@enviroflex.com

IN CANADA

ENVIROFLEX INTERNATIONAL INC.

17 BROWNRIDGE RD. UNIT 8

HALTON HILLS, ONTARIO, CANADA, L7G 0C6

TEL. (905) 636-1177 FAX (905) 636-1178

TOLL FREE 1-877-ENV-FLEX

Internet: http://www.enviroflex.com

Email: info@enviroflex.com

Washable Filters

Field Applications:

Filtration of welding fumes, plasma & laser cutting, dump
stations, product recovery & general pollution control problem
applications.

The  material  is  100%  polyester,  which  is  especially  suitable  for  the  extraction  of  welding
smoke.

This material is characterised by uniform parallel pleats on the dust side. This gives the filter
the maximum square footage with a uniform pleat distance. Conventional pleating doesn’t
have  this  uniform  pleating  thus  increasing  the  pressure  drop  due  to  overlapping  the  pleats
and  minimizing  the  square  footage  of  the  filter.  The  end  result  is  that  the  washable  filter
does not plug up as quick and there is more airflow through the washable filter.

The  material  has  a  thickness  of  0.022"  and  is  used  in  filter  cartridges  and  can  be
automatically  cleaned  by  pulsing  the  filter  with  compressed  air.  The  filter  can  also  be
washed with a detergent, as it does not retain any moisture.

Specifications:

Colour:

Available in black and white.

Weight:

Approximately 275 grams per square meter(8oz. per

square yard)

BIA Classification:

U.S.G. (see pages 3 and 4)

Air Permeability:

650 m³/hr. at 20MM W.G. (25cfm @ ½" W.G.

)

Temperature Resistance:

Standard 80º C (176º F). Please note when ordering to
state a higher temperature if it exceeds the standard
temperature rating.

Efficiency:

99.2%

Clean Off Behaviour:

Good

Date: November 14, 2008

Section 2

Page 1 of 4

ENVIROFLEX



FOR A HEALTHIER WORK ENVIRONMENT

IN U.S.A.

ENVIROFLEX INTERNATIONAL INC.

1051 CLINTON ST.

BUFFALO NY, USA 14206-2823

TEL. (716) 883-2319 FAX (716) 892-2139

TOLL FREE 1-866-ENV-FLEX

Internet: http://www.enviroflex.com

Email: Info@enviroflex.com

IN CANADA

ENVIROFLEX INTERNATIONAL INC.

17 BROWNRIDGE RD. UNIT 8

HALTON HILLS, ONTARIO, CANADA, L7G 0C6

TEL. (905) 636-1177 FAX (905) 636-1178

TOLL FREE 1-877-ENV-FLEX

Internet: http://www.enviroflex.com

Email: info@enviroflex.com

Test Results

Test Basis:

ZH1/487 ABS 2 is a European test regarding filter
efficiencies of filter fabrics for dust extraction installations.

Test Sample

Filter Fabric

2.1

Built-up:

Filter Fabric, single Layer

2.2

Type Name:

Open pleat washable

2.3

Material Name:

Polyester washable

2.4

Approved Category: U.S.G.

Manufacturer’s Data of the Filter Fabric

3.1

Materials and Type

Polyester Fabric

3.2

Surface Weight:

280 gr/m²(8.25 oz./sq. yd.)

3.3

Air Permeability:

700 m³/m

/ hr at 200 Pascal (38 CFM @ 0.8" W.G.)

3.4

Dust Side:

Parallel Lined (25 CFM per square foot @ 0.5" W.G.)

3.5

Colour:

Black or White

Penetration Test of the Filter Fabric

4.1

Filtration Speed:

0.056 m/s (11 ft./min)

4.2

Quartz dust

Concentration:

200 +/- 20 mg/m³ (.087 grains/ft³)

4.3

Requirements

Category-G-Maximum Penetration Degree is 0.5%

Date: November 14, 2008

Section 2

Page 2 of 4

ENVIROFLEX



FOR A HEALTHIER WORK ENVIRONMENT

IN U.S.A.

ENVIROFLEX INTERNATIONAL INC.

1051 CLINTON ST.

BUFFALO NY, USA 14206-2823

TEL. (716) 883-2319 FAX (716) 892-2139

TOLL FREE 1-866-ENV-FLEX

Internet: http://www.enviroflex.com

Email: Info@enviroflex.com

IN CANADA

ENVIROFLEX INTERNATIONAL INC.

17 BROWNRIDGE RD. UNIT 8

HALTON HILLS, ONTARIO, CANADA, L7G 0C6

TEL. (905) 636-1177 FAX (905) 636-1178

TOLL FREE 1-877-ENV-FLEX

Internet: http://www.enviroflex.com

Email: info@enviroflex.com

4.4

Test Results

Average Penetration Degree 0.13% (tests)

Standard aberration:

0.05%

At a filtration speed of 0.056 m/s the average penetration degree is 0.5%. The test
requirements for the filter fabric efficiency for the category U.S.G. are successful.

Pressure Drop

5.1

Filtration Speed:

0.056 m/s (11 ft./min.)

5.2

Filter Load

200 m³/m²/hr. (10.9 ft³/ft²/min.)

5.3

Test Results

Average Pressure Drop:

79 pa (6 tests on clean material) (0.3" W.G.)

Air Permeability Test:

506 m³/m²/hr (27.66 ft³/ft²/min.)

The air permeability of the filter material is ascertained at a differential pressure of
200 Pa. (0.8" W.G)

Surface Weight Test:

273 g/m² (8.05 oz.yd.²

Notes:

The requirements are fulfilled.

CLAR

CLARIFICATION OF EUROPEAN STANDARD ZH1/487

IFICATION OF EUROPEAN STANDARD ZH1/487

The BIA is a government agency, which directs the setting up of rules and standards in order
to meet certain safety and quality standards in Europe.  One of those is the AH1/487 ABS 2
test  procedure  for  different  filtering  media  used  in  dust  collection  equipment.  The  test  is
carried out on small media samples, and the test dust is standardized. The approach velocity
on the media during the test is standardized on 11 F.P.M. (11:1 A/C ratio). During the test, a
quantity of approximately 0.078 Gr/cu.ft. of dust is fed to the media, and the penetration is
measured.  In  this  way  a  certain  penetration  is  determined  which  rates  the  media  in
preclassified  levels,  the  so  called  U.S.G.  or  C.  The  U  media's  are  the  lowest  efficiency
medias;  the  C  medias  are  the  highest  efficiencies.    The  maximum  allowable  penetration
degrees for the different classifications are:

Date

November 14, 2008

Section 2

Page 3 of 4

ENVIROFLEX



FOR A HEALTHIER WORK ENVIRONMENT

IN U.S.A.

ENVIROFLEX INTERNATIONAL INC.

1051 CLINTON ST.

BUFFALO NY, USA 14206-2823

TEL. (716) 883-2319 FAX (716) 892-2139

TOLL FREE 1-866-ENV-FLEX

Internet: http://www.enviroflex.com

Email: Info@enviroflex.com

IN CANADA

ENVIROFLEX INTERNATIONAL INC.

17 BROWNRIDGE RD. UNIT 8

HALTON HILLS, ONTARIO, CANADA, L7G 0C6

TEL. (905) 636-1177 FAX (905) 636-1178

TOLL FREE 1-877-ENV-FLEX

Internet: http://www.enviroflex.com

Email: info@enviroflex.com

U:   5%        S:   1%    G:  0.5%    C:  0.1%

In  point  4.3  the  applications  categories  are  described  above  are  specified  for  the  media
tested.  In  case  of  the  "open  pleat  washable"  this  media  has  obtained  the  G  (U&S
automatically)  level  by  performing  with  a  penetration  degree  less  than  0.5%.  In  Europe,
there are certain listings, which prescribes certain classified filter medias for certain types of
dust.  Outside Europe, such listings are not available yet.  In point 5.4 the air permeability is
mentioned  as  value  provided  by  the  manufacturer  of  the  media.  The  value  is  given  in
m³/m²/hr. at a pressure drop of 20MM W.G. (approximately 0.8 inches of water). The actual
measured air permeability during the test was 506 m³/m²/hr. (27.66 CFM/Sq.Ft./Min.) point
8 in the test results.

For  Welding  fume,  generally  the  "open  pleat  washable"  can  be  used  very  successfully.
However,  special  treatment  on  the  media  utilizing  a  Precoat  should  be  applied  during
commissioning of the filter unit. By using this special silicone based Precoat a much better
reverse jet-pulse cleanability of the media is obtained.

Regarding  washing  of  the  "open  pleat  washable"  polyester  medias,  we  recommend  a
medium  pressure  cleaner  using  warm  water  (max.60  deg.  C)  with  Precipiclean



. The

nozzle of the cleaner should be approximately 20 inches away from the filter in order not to
damage the media.

Date: November 14, 2008

Section 2

Page 4 of 4



6” Bench Mount Model

No Description Qty Arm

model

103.1028

(10ft. Arm)

Part

Number

Joint 1

1 103.1028.1

2 Joint

1 103.1028.2

3 Joint

1 103.1028.3

4 Joint

1 103.1028.4

5 Joint

1 103.1028.5

6 Joint

1 103.1028.6

7 Joint

1 103.1028.7

8 Joint

1 103.1028.8

Friction insert I
70

103.1028.9

Friction insert II
60

103.1028.10

12 Tube I 160

103.1028.11

13 Tube II 160

103.1028.12

Reinforcing
element I 160

103.1028.13

Reinforcing
element II 160

103.1028.14

21 Spring II, l=190

103.1028.15

Outer sleeve
160

103.1028.16

23 Inner

sleeve

160

1 103.1028.17

25 Orifice

160

1 103.1028.18

26 Axis

1 103.1028.19

27 Axis

1 103.1028.20

28 Lever

1 103.1028.21

29 Sleeve

2 103.1028.22

30 Support

plate

1 103.1028.23

Screw with
mushroom head
M10x30-4.8

103.1028.24

32 Nut

M10-5-C

8 103.1028.25

33a

Regular washer
10.5

103.1028.26

Spring washer
Z10.2

103.1028.27

Screw with
mushroom head
M8x30-4.8

103.1028.28

36 Nut

M8-5-C

9 103.1028.29

Regular washer
8.2

103.1028.30

Spring washer
Z8.2

103.1028.31

Spring washer
Z6.1

103.1028.32

42 Nut

M6-5-C

2 103.1028.33

Self-locking nut
M14x1.5-5-B

103.1028.34

Disk spring DI
60x14.5x3

103.1028.35

Disk spring DI
50x14.5x2.2

103.1028.36

Steel cable

3.5, l=450

103.1028.37

Bow rope clamp
5

103.1028.38

Screw M8x25-
3.6-C

103.1028.39

Self-locking nut
M8-5-B

103.1028.40

Clamping eye

10.5

103.1028.41

Screw
M14x1.5x60-
8.8-B

103.1028.42

Screw
M14x1.5x55-
8.8-B

103.1028.43

60 Hood



315/160

103.1028.44

61 Handle

160

1 103.1028.45

62 Light kit dome

103.1028.46

Shutter of inlet
160

103.1028.47

64 Wire seal GH6

103.1028.48

65 Protecting

plate

1 103.1028.49

Screw WP
M4x16

103.1028.50

67 Plug

1 103.1028.51

68 Plug

1 103.1028.52

Regular washer
15 (for wood
construction)

103.1028.53

Screw with
mushroom head
M6x16-4.8

103.1028.54

Lubricating
nipple C M8x1

103.1028.55

74 Wing nut M6

103.1028.56

Internal
wrenching
screw M8x20-
8.8

103.1028.57

Steel rivet

3.2x8

103.1028.58

79b

Steel rivet

3.2x8

103.1028.59

80 Handle

1 103.1028.60

Flexible hose
ST-160,
l=535mm (21”)

103.1028.61

Gear clamp
OST-160

103.1028.62

Flexible hose
ST-160
l=640mm (25”)

103.1028.63

Flexible hose
ST-160
l=430mm (17”)

103.1028.64

Joint’s wheel
160

103.1028.65

P2 Connector

4 103.1028.66

P3 Screw

M8x20

12 103.1028.67

Self-locking nut
M8

103.1028.68

Regular washer
8.4 C

103.1028.69

Friction insert



30x8x6

103.1028.70

Reinforcing
element IV

103.1028.71

Disk spring
12.5x6.2x1

103.1028.72

6” Bench Mount Model

Description

Qty

Arm model

103.1028

(10ft. Arm)

Part Number

Joint 1

103.1028.1

Joint 2

103.1028.2

Joint 3

103.1028.3

Joint 4

103.1028.4

Joint 5

103.1028.5

Joint 6

103.1028.6

Joint 7

103.1028.7

Joint 8

103.1028.8

Friction insert I
70

103.1028.9

Friction insert II
60

103.1028.10

Tube I 160

103.1028.12

Tube II 160

103.1028.13

Reinforcing
element I 160

103.1028.14

Reinforcing
element II 160

103.1028.15

Spring II, l=190

103.1028.21

Outer sleeve
160

103.1028.22

Inner sleeve 160

103.1028.23

Orifice 160

103.1028.25

Axis I

103.1028.26

Axis II

103.1028.27

Lever

103.1028.28

Sleeve

103.1028.29

Support plate

103.1028.30

Screw with
mushroom head
M10x30-4.8

103.1028.31

Nut M10-5-C

103.1028.32

33a

Regular washer
10.5

103.1028.33a

Spring washer
Z10.2

103.1028.34

Screw with
mushroom head
M8x30-4.8

103.1028.35

Nut M8-5-C

103.1028.36

Regular washer
8.2

103.1028.37

Spring washer
Z8.2

103.1028.38

Spring washer
Z6.1

103.1028.41

Nut M6-5-C

103.1028.42

Self-locking nut
M14x1.5-5-B

103.1028.46

Disk spring DI
60x14.5x3

103.1028.47

Disk spring DI
50x14.5x2.2

103.1028.48

Steel cable



3.5, l=450

103.1028.51

Bow rope clamp
5

103.1028.52

Screw M8x25-
3.6-C

103.1028.53

Self-locking nut
M8-5-B

103.1028.54

Clamping eye



10.5

103.1028.55

Screw
M14x1.5x60-
8.8-B

103.1028.57

Screw
M14x1.5x55-
8.8-B

103.1028.58

Hood

315/160

103.1028.60

Handle 160

103.1028.61

Light kit dome

103.1028.62

Shutter of inlet
160

103.1028.63

Wire seal GH6

103.1028.64

Protecting plate

103.1028.65

Screw WP
M4x16

103.1028.66

Plug I

103.1028.67

Plug II

103.1028.68

Regular washer
15 (for wood
construction)

103.1028.69

Screw with
mushroom head
M6x16-4.8

103.1028.70

Lubricating
nipple C M8x1

103.1028.73

Wing nut M6

103.1028.74

Internal
wrenching
screw M8x20-
8.8

103.1028.75

Steel rivet



3.2x8

103.1028.79

79b

Steel rivet



3.2x8

103.1028.79b

Handle

103.1028.80

Flexible hose
ST-160,
l=535mm (21”)

103.1028.81

Gear clamp
OST-160

103.1028.82

Flexible hose
ST-160
l=640mm (25”)

103.1028.84

Flexible hose
ST-160
l=430mm (17”)

103.1028.85

Joint’s wheel
160

103.1028.P1

Connector I

103.1028.P2

Screw M8x20

103.1028.P3

Self-locking nut
M8

103.1028.P4

Regular washer
8.4 C

103.1028.P5

Friction insert

30x8x6

103.1028.P7

Reinforcing
element IV

103.1028.P8

Disk spring
12.5x6.2x1

103.1028.P9

Drawing 19. (6” arm) Damper – both Wall Mounted and bench mount.

33a

Drawing 13. (6” arm) Socket of SNORKVAC™ arm – Bench Mount.

51+55

Drawing 12. (6” arm) SNORKVAC™ bench mount arm

85 84