PDF User Manual

  1. Home
  2. Manuals
  3. EUROM B950I User Manual

EUROM B950I User Manual

B1000i\ B2000i\ B3000i

Made by: EUROM
Type: User Manual
Category: Inverter
Pages: 19
Size: 1.84 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

 
 

User manual 

 
 
 

 

 

B950I, B1000i, B2000i, B3000i 

 

 

 

 

 


background image

 

 

 

Page 20 

 
 

 

Always read the user manual thoroughly before using the generator.  

 

 

Never use the generator in a closed room/area. Exhaust may cause suffocation.  

 

 

 

The exhaust pipe becomes very hot during operation. Do not touch the exhaust pipe after use. 

 

 

Only use approved cables. 

 

 

Fuel is very flammable, be careful when filling with gasoline. Do not fill when you are close to open 

fire, lighted cigarettes, sparks or similar. Always clean up spilled gasoline.  

 

 

Standby power generators for buildings must only be connected by an authorised electrician, who 
must comply with the regulations in question. Incorrect connection can make the power/electricity 

run back to the generator. This can cause an electric shock if a person gets in contact with the 

generator. After the power has been restored the generator may explode, burn or cause a burn in 
the electric system.  

 

 

Always inspect all connections before you start the machine. This can prevent an accident. 

 

 

Always place the generator 1 meter away from buildings or other equipment during operation.  

 

 

Only use the generator on a horizontal surface. 

 

 

Draw attention to how the generator is to be stopped and understand all its functions. Never leave 

the use of the generator to persons who has not received any instruction about the operation.  

 

 

Keep children away from the generator during operation. 

 

 

Using the generator with wet hands may lead to electric shock.  

 

 

Never use the generator in rain or snow. Always make sure that the generator does not become 
wet.  

 

NOTE

 

If you are going to use the generator in thin statums of air, higher than 1500 meter above water 
surface you shall contact your dealer for guidance.   

 

   

  
  

 


background image

 

 

 

Page 21 

    
   
    

1. Contents 

 
1. Contents

...........................................................................................................................................21 

2. Identification of components

...............................................................................................................22 

3. Automatic current control (SMART)

.....................................................................................................22 

4. Before start - Oil

................................................................................................................................23 

4.1. Before start - gasoline

.................................................................................................................24 

4.2. Before start - air filter

...................................................................................................................24 

5. Start

.................................................................................................................................................25 

6. Operation of the generator

.................................................................................................................27 

6.1. Alternating current

......................................................................................................................27 

6.2. Indicators

...................................................................................................................................28 

6.3. Direct current

..............................................................................................................................28 

6.4 Oil warning

..................................................................................................................................30 

6.5 Stop

...........................................................................................................................................30 

7.  Maintenance

....................................................................................................................................31 

7.1 Changing oil

................................................................................................................................31 

7.2 Air filter

.......................................................................................................................................32 

7.3 Spark plug

..................................................................................................................................33 

8. Transport and storage

........................................................................................................................33 

9. Specifications

....................................................................................................................................35 

10. Trouble shooting

..............................................................................................................................36 

 

 
 
 

 

 
 

 
 

 

 
 

 

 

 

Spare parts

 

 

Part list and explosive drawings for the specific product, please contact your 

dealer.  

If you help find part numbers yourself, it will ease the service. 

 

For purchase of spare parts, please contact your dealer. 

 


background image

 

 

 

Page 22 

 2. Identification of components 

 

 
 

 

 
 

 
 

 

 
 

 

 
 

 
 

 

 
 

 

 
 

 
 

 

3. Automatic current control (SMART) 

 

The engine speed is automatically adjusted, when the current is disconnected. The same way the speed goes 
up when you connect the current. This ensures the fuel consumption being held at a minimum. 

 

Warning -  

The automatic regulation does not work effectively if an even electric current is needed.  

 

Warning -  

When the generator is to produce a heavy, even current you shall place the switch in 

                    the OFF position in order to reduce changes in the current. 

 

Warning -  

When you work with DC (Direct Current), always place the switch in the 

OFF

 position. 

 

 

 
 

 
 

 

 
 

 

 

 

 

 

Choker 

Cover 

Starter 

Engine switch 

Control panel 

Fuel cap 

Fuel cap cent 

lever 

Cover for 
fuse 

Muffler 

DC 
receptable 

Smart contact 

Smart-Throttle switch 

Over load indicator 

Ground 
terminal 

Oil indicator 

AC  

DC circuit 
protector 

Switch 

 


background image

 

 

 

Page 23 

4. Before start - Oil 

 

NOTE 

-

 

Always inspect the generator on a horizontal surface with a turned-off engine. 

-

 

The in-built alarm system will automatically stop the engine before the oil level drops under the 
approved level. In order to avoid unpredicted disconnection you shall check the oil level regularly. 

-

 

Using the generator with too little oil can cause severe damages to the wear parts of the engine. 

 

 

 
 

Use full-synthetic premium 4-stroke oil, which meets the demands in question.(API)  

Loosen the screws that tighten the plate on the backside of the generator and remove the plate. Check the oil 
level by removing the oil stick, clean it with a dry clean cloth. Insert the oil stick without screwing it in. See the 

oil level on the stick. Fill with oil if necessary. 

Oil capacity: 0,25/0,40 L. 
 

 

 

 

 
 

 

 
 

 
 

 

   
  

  

 
 

 
 

 

 

 

 

 

Oliepind 

Fill oil until here 

Screw 

Left maintenance 

cover 

 

Air cleaner 

cover 

Oil stick 

Oil filler hole 

 


background image

 

 

 

Page 24 

4.1. Before start - gasoline  

 

 

Use regular unleaded 95 octane gasoline.   

 

Avoid getting dust, dirt or water in the tank.  

 

After filling, fasten the tank cover securely.  

 

Only fill fuel to the indicated marking (see figure below). 

 

 
 

 

  
 

 

 

 

 
 

 

 
 

 

 
 

 
4.2. Before start - air filter 

 
Check that the air filter is clean and in good shape.  

 

PROCEDURE 

Loosen the screws that fasten the plate on the backside of the generator and remove the plate. On the top of 

the air filter a tap is placed, press this down and the air filter is loosened.  

Check the filter and clean it, replace if necessary. 
  

 

 

WARNING 

Never use the generator without an air filter. This will result in dirt being drawn into the carburettor of the 

engine. 

NOTE 

- By transport you always turn the upper part of the gasoline cover to the ”OFF” position.  

 

 

Fill untill 
here

 

Fuel cap 

Fuel cap 

 


background image

 

 

 

Page 25 

5. Start 

 

WARNING 

Disconnect all machines connected to the generator before starting. 

 
 

WARNING 

Before use the generator must be grounded. Connect the ground take off on the generator with a frame 

connection e.g. an earth auger. 
 
 

Turn the upper part of the fuel cover clockwise to the ”ON” position. 

 
 

 

 
 

 

 
 

 

 

Turn the ignition switch to the ”ON” position. 

 

 
 

 

 
 

 
 

 

 
 

 

 

Gasoline cover 

Ignition switch 

 


background image

 

 

 

Page 26 

 

Place the choke of the machine in open position. To the right. 

 

 

 

Pull slowly in the starting cord of the engine until you feel resistance. Then you pull one heavy long draw. 

Never let the starting cord run back by itself, always follow it with your hand. 

  

 

 

Close the choke by placing it in the right position while the engine is warming up. 

 

   

Starting cord 

Choke 

 


background image

 

 

 

Page 27 

 

6. Operation of the generator 

 

WARNING 

In order to prevent electric shock, the generator must be grounded. This is done by connecting the frame 
take off of the generator with a frame connections e.g. an earth auger. 

 

NOTE 

-

 

Do not exceed the voltage limit stated for a regular plug. 

-

 

Do not connect the generator to a closed system in e.g. a house. This may cause damages on both 
the circuit and the generator.  

-

 

Do not make any amendments to the generator. 

-

 

Do not connect more generators in a parallel connection.  

-

 

Do not extend the exhaustion on the generator.  

-

 

By using an extension cord you shall use a heavy and flexible cable.  

-

 

Maximum length of extension cords:  

-

 

1.5 mm

2

 = 60 meters 

-

 

2.5 mm

2

 = 100 meters 

-

 

During operation you must not place the generator close to any other electrical cables.   

-

 

The DC exit can be used together with the AC exit, but draw attention to the current intensity being 
able to vary if the load is too high. 

 

 
6.1. Alternating current 

 

PROCEDURE 

1.

 

Start the generator and note that the green light in the panel goes green.  

2.

 

Make sure that the apparatus you want to use has been turned off. 

3.

 

Insert the plug into the generator.  

4.

 

Turn the apparatus on*. 

   

  

 

NOTE 

-

 

Continued overload of the generator (indicated by a red light) can damage the generator and shorten 
the life of the engine.  

-

 

Always inspect that the receiver apparatus works and is in good shape before use.  

-

 

If the apparatus starts performing irregularly or if the engine suddenly stops during operation you shall 

stop the generator and disrupt the current by removing the plug from the generator. 

 
 

 

 


background image

 

 

 

Page 28 

 
6.2. Indicators 

 

-

 

The running indicator will be lit during regular running (green light). 

-

 

If the generator is overloaded the green light will turn itself off and the red indicator for overload will be 

lit. At the same time the current for the apparatus will be disconnected. In this case you must stop the 

generator and inspect it for the source of the overload. 

 

 

When starting the generator it may occur that both the green as well as the red indicator is lit. The red 

indicator should turn itself off in a few seconds. If not you must stop the generator and inspect it for the 
source of the overload. You can also contact your dealer. 

 
 

When starting if the green indicator is not lit, but the red indicator is, you must stop the generator and retry.   

 

 
 

 
 

 

 
 

 

 
 

 

6.3. Direct current 

 

6.3.1

 

Connect the charging cables on the DC take-off on the generator to the correct poles as shown 

on the drawing. 

 
 

 

 
 

 
 

 

 
 

6.3.2

 

Start the generator.  

The take off for alternating current can be used with the direct current take-off.   

Oilalarm 

NOTE: Avoid 12 volt charging 
directly to batteries as this may 
cause overheating of the 
battery. Texas recommend only 
to use a 230 volt battery 
charger. Charging of batteries 
should only be done in 
ventilated places due to risk of 
sparkling gasses.

 

Current out 

green light 

Overload 

red light 

 


background image

 

 

 

Page 29 

 

 

 

WARNING 

-

 

In order to prevent the possibility of a spark close to the battery, you must first connect the charging 
cable to the generator and thereafter to the battery.  

When dismounting, start by dismounting the battery.  

-

 

When charging batteries which are still mounted in cars, it is important that the frame cable has been 
removed from the pole of the battery. After charging the frame cable is mounted on the correct pole. 

-

 

This procedure prevents the risk of a short circuit between generator and the chassis of the car. 

 

 

NOTE 

-

 

Do not try to start a car while the generator is connected to the battery of the car. The generator may 

be damaged.  

-

 

Always check that the generator has been correctly connected to the battery. 

 
 

WARNING 

Always respect the indicated instructions for use of battery 

 

NOTE 

12 V take-off on the generator must only be used for charging 12 V automobile batteries. 

By use of direct current take off the automatic current control must be turned off. 

 


background image

 

 

 

Page 30 

 

6.4 Oil warning 

 
There is an inbuilt oil alarm on the generator. This means that if the generator is lacking oil during operation 

the generator will stop automatically. At the same time the oil lamp in the panel will be lit. 

 

6.5 Stop 

 

 

 

 

 

 
 

 
 

 

 
 

 

 
 

 

 
 

 
 

 

 

NOTE 

In case of emergency the generator can be turned off on the ON/OFF switch on the side of the generator. 

Turn the apparatus off and remove the plug from the generator.  

Turn the generator off on the ON/OFF switch on the side of the generator.  

Turn the upper part of the gasoline cover anti-clockwise to the ”OFF” position. 

 

 

Oil alarm 

Engine Switch 

Fuel cap 

 


background image

 

 

 

Page 31 

 

7.  Maintenance 

 
 

 
 

 
 

 

Part 

 

Every use 

 

1. month 

 

or 

 

10 hours 

 

every 3. 

month. 

 

or 

 

50 hours   

 

every 6. 

month. 

 

or 

 

100 hours 

 

every year  

 

or 

 

300 hours 

Check 

 

 

 

 

Oil 

Replace 

 

 

 

Check 

 

 

 

 

Air filter 

Clean 

 

 

X1 

 

 

Sparking plug 

Clean – adjust 

 

 

 

 

Sparking plug – 

spark screen 

Clean 

 

 

 

 

Gasoline- tank / 

filter 

Clean 

 

 

 

 

Gasoline hose 

Check 

Every 2nd year (replace if necessary) 

 
 

Check should be carried out more often if the generator is being used in dusty areas. 

 

7.1 Changing oil 

 
 

 

 

 

NOTE 

-

 

The purpose of the maintenance is to keep the generator in its best possible shape. 

-

 

Repairs should always be carried out by an authorized Texas Power Line dealer. 

WARNING 

The ignition switch and upper part of the gasoline cover of the generator must always be in the OFF position 

when changing oil.   

NOTE 

-

 

Replace oil while the oil is still warm this gives a complete and quick oil change. 

 


background image

 

 

 

Page 32 

 

PROCEDURE 

-

 

Unfasten the screws that fasten the plate on the back side of the generator and remove the plate.  

-

 

Remove the oil stick. 

-

 

Pour the used oil into a can. 

-

 

Fill with the recommended oil and check the oil level. 

-

 

Put the plate back in its place and fasten the screws safely.   

 
 

 

 
 

 

 
 

 
 

 

 

NOTE 

Always get rid of the used oil in the best way so that you save the environment as much as possible. 

 

 

7.2 Air filter 

 

 

 

 
 

 

 
 

 

WARNING 

Never use gasoline or other flammable fluids to clean the air filter. 

PROCEDURE 

-

 

Unfasten the screws that fasten the plate on the back side of the generator and remove the plate.    

-

 

On the top of the air filter a tap is placed, press this down and the air filter is loosened.   

-

 

Wash the air filter thoroughly in mild soapy water. Rinse with warm water. Let the air filter dry 

thoroughly . 

-

 

Soften the filter in pure engine oil and squeeze the filter for redundant oil.  

-

 

Put the filter back in its place in the holder and in the machine. 

-

 

Put the plate back in its place and fasten with screws. 

 

 

 

Cover screw 

Left cover 

Max. level 

Oil stick 

Drain tap

 

Air filter box 

Air cleaner 

Air cleaner body 

Screw 

Insert here

 

 


background image

 

 

 

Page 33 

 

7.3 Spark plug 

 
Recommended spark plugs: NGK CR5HSB / DENSO U16FSR-UB  

 

 

 
 

 

 
 

 
 

 

 

 

8. Transport and storage 

 

 

 

PROCEDURE 

-

 

Remove the cover at the top of the generator. 

-

 

Remove the sparking plug cover. 

-

 

Remove dirt around the sparking plug.  

-

 

Use a sparking plug wrench to unfasten the sparking plug.  

-

 

Check the sparking plug, replace if the isolation has cracked.  

-

 

Clean the sparking plug with a steel brush if you want to reuse it.  

-

 

Measure the electrode distance, be careful not to damage the sparking plug.  

-

 

The distance should be 0,6 mm – 0,7 mm. 

-

 

Insert the sparking plug carefully and fasten it with a sparking plug wrench.  

-

 

Normally you have to fasten a new sparking plug by 

½

 turn by the means of the sparking plug wrench. 

-

 

You only have to fasten a used sparking plug by 

1/8

 – 

¼

 turn.  

-

 

Mount the sparking plug cover . 

-

 

Put the cover back on the generator. 

NOTE 

By transport the generator must be placed in normal standing position and the upper part of the gasoline cover 
is turned anti-clockwise to the ”OFF” position. 

WARNING 

-

 

Never overfill the fuel tank. 

-

 

Never use the generator while it is onboard a vehicle, only operate the generator in an open and 

ventilated area.  

-

 

By transport you must avoid direct sun light. If the generator is exposed for direct sun light for many 
hours, gasoline steams may evaporate and self-ignite.  

-

 

By transport on uneven roads for longer periods of time you should drain all gasoline.  

-

 

Always draw attention to the storage area being free for dust and damps.  

-

 

Drain all fuel from the generator before storage. 

 

 

 

Cover 

Handle 

Wrench 

Cap 

 


background image

 

 

 

Page 34 

 

PROCEDURE - GASOLINE 

-

 

Drain all gasoline from the tank into a container. 

-

 

Turn the ignition switch of the generator to the ON position. 

-

 

Loosen the delivery screw of the carburettor and drain all the fuel of the carburettor into a tank. 

-

 

Remove the sparking plug cover and pull the starting cable 3-4 times. Thereby the fuel is drained in 
the gasoline pump. 

-

 

Turn the ignition switch of the generator to the OFF position 

-

 

Fasten all screws securely 

 

 

 
 

 

 
 

PROCEDURE - OIL 

-

 

Change the oil on the generator.  

-

 

Remove the sparking plug and pour app. one spoonful of pure engine oil into the cylinder.  

-

 

Pull the starting cable 3 - 4 times, so that the oil is allocated. Put the sparking plug back in its place.  

-

 

Pull the starting cable of the generator slowly until you feel resistance.  

-

 

Now the generator is ready to be stored. 

 

 

 
 

 

 

 

Starting cord 

 


background image

 

 

 

Page 35 

 

9. Specifications 

 

Dimension and weight 

 

B1000i 

B2000i 

L x B x H 

450 x 240 x 380 mm 

549x291x405 mm 

Dry weight 

14 kg 

22 kg 

 

Engine 

Model 

KG55 

KG105 

Engine 

4-stroke, OHV 

Stroke volume (drilling x stroke 
length) 

55 cc (43,5 x 36,0mm) 

64 cc (56,0 x 40,0 mm) 

Compression 

8,5 : 1 

Engine speed 

rev/min (with automatic regulation switched off) 

Cooling 

Air 

Ignition 

Transistors 

Oil capacity SAE 30 

0,25 Liter 

0,40 Liter 

Fuel tank capacity 

2,1 Liter 

4,1 Liter 

Noise level at 7 metres distance 

64 dB(a)  

59 dB(a) 

 

Generator 

Model 

B1000i 

B2000i 

Volt(V) 

230 

Frequency(Hz) 

50 

Ampere(A) 

3,9 

7,0 

Effect (KVA) 

0,9 

1,6 

AC ud 

Max effect (KVA) 

2,0 

DC out 

Only for charge of car batteries. 

Max load effect: 8A 

 

 

 
 

 
 

 

 


background image

 

 

 

Page 36 

10. Trouble shooting 

 

Engine does not start: 
 
 
 

 

     No 

 
          Yes 

 

 

     No 

 
 
          Yes 
 
                                                    No 
 
 
          Yes 
 
                                                    No 
 
 

 

                                                         No 

 
 
 
 

 

 

 

 

 

 

 

 

 

          No 

Enough fuel in tank

Is the generator turned on

 ? 

Fill fuel into tank 

Enough oil

Turn on the generator.

 

Fill with oil

 

Spark from spark plug

Replace spark plug

 

Still no spark ?

 

Contact your dealer  

 


background image

 

 

 

Page 37 

 

 

Connected tool/apparatus does not work.  
 
 
 
    Yes                 No 
  
 

 

 

    Yes 

 
                 

                No 

 
 

   No 

 
 
    Yes 
 
 
 
 
No power from DC outlet 
 
 

 

                      No 

sl 
 
    Yes 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

”output” lamp lights 

”alarm” indicator lights 

Check that tool/appatus works 

 
Contact your 
dealer  
 

Replace tool/apparatus.  

 

Is automatic safety on

 ? 

Turn it on 

Contact your dealer