Full Text Searchable PDF User Manual
Important Information and
Customer Assistance
Introduction
A1 English
Important Information
•
Federal Laws Governing the Use of Radar Detectors
It is not against federal law to receive radar transmissions with your Cobra radar/
laser detector. The Communications Act of 1924 guarantees your right to receive
radio transmissions on any frequency. Local laws that contravene this Act, while
illegal, may be enforced by your local law enforcement officials until and unless
they are prohibited from doing so by federal court action.
Safety Alert
Use of this product is not intended to, and does not, ensure that motorists or
passengers will not be involved in traffic accidents. It is only intended to alert
the motorist that an emergency vehicle equipped with a Cobra Safety Alert
transmitter is within range as defined by that product. Please call local fire
and police departments to learn if coverage exists in your area.
Safe Driving
Motorists, as well as operators of emergency or service vehicles, are expected to
exercise all due caution while using this product, and to obey all applicable traffic laws.
Security of Your Vehicle
Before leaving your vehicle, always remember to conceal your radar detector
in order to reduce the possibility of break-in and theft.
Customer Assistance
•
Should you encounter any problems with this product, or not understand its many features,
please refer to this owner’s manual. If you require further assistance after reading this
manual, Cobra Electronics offers the following customer assistance services:
For Assistance in the U.S.A.
Automated Help Desk
English only. 24 hours a day, 7 days a week 773-889-3087 (phone).
Customer Assistance Operators
English and Spanish. 8:00 a.m. to 5:30 p.m. Central Time
Mon. through Fri. (except holidays) 773-889-3087 (phone).
Questions
English and Spanish. Faxes can be received at 773-622-2269 (fax).
Technical Assistance
English only. www.cobra.com (on-line: Frequently Asked
Questions). English and Spanish. productinfo@cobra.com (e-mail).
For Assistance Outside the U.S.A.
Contact Your Local Dealer
©2010 Cobra Electronics Corporation
6500 West Cortland Street
Chicago, Illinois 60707 USA
www.cobra.com
Customer Assistance
XRS 9370
14 BAND
™
HIGH-PERFORMANCE
DIGITAL RADAR/LASER
DETECTOR WITH XTREME RANGE
SUPERHETERODYNE
®
TECHNOLOGY
Nothing
Comes Close to a Cobra
®
English
Operating Instructions
Printed in China
Part No. 480-662-P
Version A
Nothing
Comes Close to a Cobra
®
English
For more information or to
order any of our products,
please visit our website:
www.cobra.com
CB Radios
microTALK
®
Radios
Radar/Laser Detectors
Safety Alert
®
Traffic Warning Systems
Truck-Specific Navigation Systems
HighGear
®
Accessories
CobraMarine VHF Radios
Power Inverters
LED Lights
Jumpstarters
Accessories
The Cobra line of quality products includes:
™
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page F1
X K Ka V S
L
This booklet describes the simple steps for mounting and setting up your detector. It also provides helpful
information about how radar and laser guns are used and how you can interpret the alerts you receive.
Controls, Indicators and Connections
•
Accessories Order Info and
Trademark Acknowledgement
Nothing
Comes Close to a Cobra
®
25
Customer Assistance
Display and Product Features
Introduction
Nothing
Comes Close to a Cobra
®
A3
Xtreme Range
Superheterodyne
®
Technology
With super-fast sweep circuitry,
XRS provides extra detection range
and the best possible advance warning
to even the fastest radar guns
Detection and Separate Alerts For:
Radar signals (X, K, Ka and Ku bands,
with signal strength indicated), Laser
signals, Safety Alert signals, VG-2
signals, Spectre I & IV+ signals
LaserEye
®
For 360° detection of laser signals
Instant-On Ready
Detects radar guns with “instant-on”
(very fast) speed monitoring capabilities
Pop Detection
Detects the latest super-fast instant-on
single pulse radar guns
Tone Alerts
With adjustable volume
UltraBright™ Data Display
Easy-to-read with adjustable brightness
City or Highway
Modes to reduce false alerts
Alert Programming
Easy setting of radar bands to be monitored
Safety Alert
®
Traffic warning system distinguishes
important safety alerts from other
K band signals
Manual Mute or Auto Mute
A mute function of audio alerts
IntelliMute
®
A mute function reduces false audio alerts
by sensing engine RPMs
IntelliMute
®
Pro
Prevents detection by radar detector detectors
(RDDs) when traveling at slower speeds
Mounting
Mounts easily on windshield or dashboard
Product Features
•
Congratulations! You’ve made a smart choice by purchasing a high
performance radar/laser detector from Cobra. Just look at some of the
sophisticated features and capabilities your new unit includes:
Display
•
Controls, Indicators
and Connections
Introduction
A2 English
12V DC
Power Jack
On-Off/ Volume Control
Allows you to adjust the
volume of the tone alerts.
Audio Jack
City Button
For City or Highway
modes to reduce
false alerts. (Also
turns Ku alerts On
and Off.*)
LaserEye
For 360° detection
of laser signals.
Windshield Bracket
Release Button
Speaker
* Press and hold for four seconds
to access these functions.
WARNING
Modifications or parts substitutions not approved
by Cobra Electronics Corporation may violate
FCC Rules and void your authority to operate
this equipment.
IntelliMute
Indicator
Radar, VG-2,
Spectre I & IV+ and
Safety Indicators
X K Ka
V
S
c
X K
Ka V S
c
X K Ka
V
S
c
NOTE: In This Manual
When steady,
the display will
be shown:
When blinking,
the display will
be shown:
X & K will light
simultaneously
when indicating
Ku detection:
Signal
Strength,
Pop, Laser,
City/Highway and
IntelliMute Pro
Mode Indicators
Signal Strength: 1 (weakest) to 5 (strongest)
Dim Button
Allows you to adjust
the UltraBright Data
Display brightness for
easy reading. (Also
turns VG-2 and
Spectre I & IV+ alerts
On and Off.*)
IntelliMute Button
Engine RPM sensing
mute function which
reduces false alerts.
Button turns IntelliMute
On and Off. (Also enters
IntelliMute setting mode.*)
Mute Button
For manual mute or
auto mute of audio
alerts.
Ordering From U.S.A.
Call 773-889-3087 for pricing or visit www.cobra.com.
For Credit Card Orders
Call 773-889-3087 [Press one from the main menu] 8:00 a.m. to 5:30 p.m. Central Time,
Monday through Friday.
Make Check or Money Order Payable To
Cobra Electronics, Attn: Accessories Dept.,
6500 West Cortland Street, Chicago, IL 60707 U.S.A.
To Order Online
Please visit our website: www.cobra.com.
Item #
Description
420-030-N-001
Straight 12V Power Cord
420-026-N-001
Coiled 12V Power Cord
545-159-N-001
Windshield Mounting Bracket
CLP-2B
Dual Port Power Adapter
Trademark Acknowledgement
•
Cobra
®
, DigiView
®
, EasySet
®
, Extra Sensory Detection
®
, IntelliMute
®
, IntelliMute Pro
®
,
IntelliShield
®
, LaserEye
®
, Nothing Comes Close to a Cobra
®
, Safety Alert
®
Traffic Warning
System, Strobe Alert
®
, VG-2 Alert
®
, Xtreme Range Superheterodyne
®
and the snake design
are registered trademarks of Cobra Electronics Corporation, USA.
Cobra Electronics Corporation™, 14 Band™, 15 Band™, Extreme Bright DataGrafix™,
IntelliLink™, Revolution™ Series, SmartPower™, Spectre Alert™, Super-Xtreme Range
Superheterodyne™, S-XRS™, UltraBright™, and Voice Alert™ are trademarks of Cobra
Electronics Corporation, USA.
Opticom™ is a trademark of 3M Corporation. Instaclear
®
for Ford is a registered
trademark of Ford Motor Company, Inc. Electriclear
®
for GM is a registered trademark of
General Motors Corporation. LTI Laser™ and LTI 20-20™ are trademarks of Laser
Technology, Inc. Kustom Laser™, Kustom Laser 340™ and ProLaser II™ are trademarks
of Kustom Signals, Inc. SpeedLaser™ is a trademark of Laser Atlanta. Bee III™ and Pop™
are a trademarks of MPH Industries. Stalker™ LIDAR is a trademark of Applied Concepts,
Inc. Spectre I™ and Spectre IV™ are trademarks of Stealth Micro Systems Pty. Ltd.
Interceptor VG-2™ is a trademark of TechniSonic Industries LTD. Tomar
®
is a registered
trademark of TOMAR Electronics, Inc.
Windshield
Bracket
Mount
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page A2
Nothing
Comes Close to a Cobra
®
1
Contents
Introduction
Introduction
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Controls, Indicators and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Your Detector
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Auxiliary Audio Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Highway/City Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
UltraBright Data Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Muting an Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Auto Mute Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
IntelliMute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
IntelliMute Pro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
VG-2 and Spectre I & IV+ Alert Settings . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pop Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Radar Alert Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Signals Detected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Audio Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Visual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Instant-On Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Responding to Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Understanding Radar and Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Warranty
Limited 1-Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Customer Assistance
Product Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Accessories Order Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Trademark Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page 1
Nothing
Comes Close to a Cobra
®
Installation
Your Detector
3
Installation
Your Detector
English
2
Installation
•
Where to Mount Your Unit
You will get optimum performance from your detector if you
Mount
it at a
point approximately in the center of the vehicle, as low as possible on the
front windshield without obstructing the unit’s view of the road either to
the front or rear. Make sure unit is level with the road. You can also mount
it directly on the dashboard.
The unit’s lens must not be blocked and the LaserEye should have a clear view
out the back window to allow 360° detection.
Radar and laser signals pass through glass but not through other materials
and objects. Objects that can block or weaken incoming signals include:
■
Windshield wiper blades
■
Mirrored sun screens
■
Dark tinting at the top of the windshield
■
Heated windshields currently available on some vehicles
(Instaclear for Ford, Electriclear for GM.) Consult your dealer
to see if you have this option.
1.
Attach the rubber
cups to the bracket.
2.
Make sure the rubber cups and your windshield are clean.
3.
Push the bracket firmly
onto the windshield.
4.
Attach the detector to
the bracket. Check the
angle of the unit.
5.
To adjust the angle if
necessary, gently push or
pull on the bracket to bend
it. DO NOT use the detector
to bend the bracket.
6.
Plug the power cord
into the detector.
7.
Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
8.
You can temporarily remove the detector whenever you
wish by pressing the bracket release button and sliding
it off the bracket.
Windshield Mounting
The LaserEye Should Have a Clear View
Windshield Mounting
Dashboard Mounting
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page 2
To Turn On the Unit and Adjust the Audio Volume
Rotate the
On-Off/
Volume
control
clockwise (away
from you).
Tone
Visual Display
Three beeps
h
appears in the display
indicating that the power
is On
Getting Started
Getting Started
•
Your Detector
Nothing
Comes Close to a Cobra
®
5
Installation
Your Detector
English
4
1.
Place the detector on the dashboard to find a location
where the unit has a clear, level view of the road.
The angle can NOT be adjusted after mounting.
2.
Remove the paper backing
from one side of the hook-
and-loop fastener.
3.
Attach the pad to the
dashboard at your chosen
location and remove the
other paper backing.
4.
Attach the detector to the
hook-and-loop fastener.
You can remove and
reattach the unit as
often as you like.
6.
Plug the power cord
into the detector.
7.
Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
Dashboard Mounting
Power On
X K Ka V S
h
On-Off/
Volume Control
Rotate clockwise
(away from you)
NOTE
In some vehicles, power is supplied to the cigarette lighter even while the
ignition is Off. If this is the case with your vehicle, you should turn Off
or unplug your detector when parking for lengthy periods.
Auxiliary Audio Jack
•
The Auxiliary Audio Jack can be used to connect external speakers in
environments with high ambient noise levels. The internal speaker will
be disconnected. (This uses a mini stereo audio connector.)
Auxiliary
Audio Jack
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page 4
Settings
Your Detector
Nothing
Comes Close to a Cobra
®
7
UltraBright Data Display Brightness
You can choose from three settings for
Brightness
of the display.
You can cycle through the settings by repeatedly pushing the
Dim
button.
The factory setting is Bright.
Settings
Your Detector
English
Settings
•
When changing the
Settings
on your detector, please keep in mind:
■
Buttons can have multiple functions.
■
All settings will be stored in memory when the power is
turned Off and recalled when the power is turned back On.
Highway/City Mode
Setting your detector to
City
mode delays all X band audio alerts until
the signal strength reaches Level 3. (A single beep will sound when the
signal is first detected.) This will reduce false alerts while you are driving
in, or near, urban areas where there are many sources for conflicting
X band signals such as microwave towers and automatic door openers.
To change settings, follow the procedure listed below, which indicates
what you will see and hear as you complete each step. The factory setting
is
Highway
mode.
6
Dim Button
Press and release
Bright
Dark
Dim
Press and
release
Dim
button
City Button
Press and
release
City Mode
X K Ka V S
c
Highway Mode
X K Ka V S
h
To Change From Highway Mode to City Mode
Press and release
the
City
button.
Tone
Visual Display
One beep
c
appears in the display
To Change From City Mode Back to Highway Mode
Press and release
the
City
button again.
Tone
Visual Display
Two beeps
h
appears in the display
To Change the Brightness to Dim
Press and release
the
Dim
button
once.
Tone
Visual Display
One beep
Display dims
To Change the Brightness to Dark
Press and release
the
Dim
button
again.
Tone
Visual Display
One beep
Display remains dim
(no visual alerts will be seen)
To Change the Brightness to Bright
Press and release
the
Dim
button a
third time.
Tone
Visual Display
Two beeps
Display returns
to full brightness
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page 6
Settings
Your Detector
Nothing
Comes Close to a Cobra
®
9
Settings
Your Detector
English
Muting an Alert
Your detector allows you to quickly turn Off an audio
Alert
by momentarily
pressing the
Mute
button. If you press the
Mute
button a second time
during the Alert, the audio Alert will be turned back on.
Auto Mute Mode
Auto Mute
will automatically reduce the audio volume of all alerts
after four seconds for as long as the signal is detected. The factory
setting for Auto Mute is on.
8
IntelliMute
IntelliMute
is a unique feature that allows you to avoid alerts you don’t need
to hear because you are stopped or moving slowly. By sensing the “revs”
(RPMs) of your engine, IntelliMute knows when you are at low speed and
automatically mutes audio radar alerts.
Before IntelliMute will work, you must set an activation point for your engine’s
revs (see page 10). Whenever the revs are below that point, IntelliMute will
begin muting. The activation point will be stored in memory and recalled
each time the power is turned on. The factory setting is IntelliMute Off.
NOTE
IntelliMute may not work with some vehicles because it cannot sense
the engine’s revs. In such cases, you can reduce unwanted audio alerts
by using Auto Mute and City mode when appropriate.
Mute Button
Press and release
To Turn Auto Mute Off
Press and release
the
Mute
button
while no alert
is occurring.
Tone
Visual Display
One beep
None
To Turn Auto Mute On
Press and release
the
Mute
button
again while no
alert is occurring.
Tone
Visual Display
Two beeps
None
To Turn IntelliMute On
Press and release
the
IntelliMute
button.
Tone
Visual Display
Two beeps
Dot appears next to the large
character on the right
To Turn IntelliMute Off
Press and release
the
IntelliMute
button again.
Tone
Visual Display
One beep
None
IntelliMute Button
Press and release
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page 8
Settings
Your Detector
Nothing
Comes Close to a Cobra
®
11
Settings
Your Detector
English
What to Remember While Using IntelliMute
IntelliMute
works with both City and Auto Mute modes.
Whenever your engine revs are below the activation point, the dot next
to the large character on the right side of the display will remain lit.
Above the activation point, the dot will blink twice every two seconds.
If, for any reason, the unit stops sensing your engine’s revs,
IntelliMute will indicate an error and automatically turn Off.
The rev point you set will be stored in the unit’s memory when
power is turned Off and recalled each time the power is turned On.
NOTE
The rev point must be reset if you use your detector in a different vehicle.
NOTE
When initially choosing your IntelliMute activation point, a setting
of approximately 300 to 600 RPMs above idle is recommended.
You can reset the activation point at any time to fit your individual
preferences and driving style.
Setting the IntelliMute Activation Point
Your detector must be installed in your vehicle.
CAUTION
Do not attempt to set the rev point while driving.
Your vehicle should be parked and idling.
IntelliMute must be turned on before setting the activation point. You will
hear a series of beeps as you follow the steps on the next page.
10
Below Activation Point
X K Ka
V
S
c
Above Activation Point
X K Ka
V
S
c
To Set the IntelliMute Activation Point
Press and hold
the
IntelliMute
button for two
seconds.
Tone
Visual Display
Two beeps
None
Rev your engine to
the level you wish
to set (recommend
slightly above idle)
and hold revs steady
for two seconds.
None
Three bars will
flash in succession
At the desired
rev level, press
and release the
IntelliMute
button.
Three beeps
All three bars flash
three times
Tone
Visual Display
Four beeps
E
appears
X K Ka V S
E
1
2
3
1
2
3
NOTE
If the unit is unable to sense usable pulses within
three seconds or if you do not set a rev point within
20 seconds of beginning these steps, IntelliMute will
indicate an error and automatically turn Off.
IntelliMute Button
Press and release
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page 10
Pop Alert
The Pop Mode Radar Gun is a single-pulse Doppler radar that is a feature
of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses
a single, short-time pulse to measure the target vehicle’s speed.
The Pop mode receiver senses Pop singles beyond the effective range of
Pop radar guns. As the Pop mode receiver is so sensitive, you should limit
the use of Pop Detect mode to highway and rural driving.
Pop Alert
will alert you to Pop radar signals. During the alert, the unit
continues to detect other signals. The factory setting is Pop Detect Off.
Your Detector
Settings
Settings
Your Detector
To Turn VG-2 and Spectre I & IV+ Alerts On and Off
While no signal is being
detected, press and
hold the
Dim
button
for four seconds.
Tone
Visual Display
On = Two beeps
Off = One beep
V
will blink twice in the display
V
will blink once in the display
Dim Button
Press and hold
for four seconds
VG-2 and Spectre I & IV+ Alert Settings
Police use radar detector detectors (RDDs) to spot users of radar detectors.
Your detector is able to identify signals from
VG-2
,
Spectre I
and
Spectre IV+
RDDs and can provide alerts when any of these or similar devices are in use
near your vehicle.
Your detector
can
be spotted by Spectre IV+ RDDs, but is invisible to VG-2 and
Spectre I RDDs. You can choose whether you want to be alerted to VG-2 and
Spectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I & IV+
alerts is Off.
On/Off Indicator
X K Ka
V
S
c
Nothing
Comes Close to a Cobra
®
13
English
12
IntelliMute Pro
IntelliMute Pro
prevents detection by radar detector detectors (RDDs) such as
VG-2, Spectre I and Spectre IV+ when traveling at slower speeds. It is intended
for use by experienced users only.
When IntelliMute Pro is turned On, and engine RPMs are below the IntelliMute
activation point, your detector’s radar detection circuits are turned Off to prevent
detection by RDDs.
Before IntelliMute Pro can be turned On, you must have turned On and Set the
IntelliMute activation point. (See pages 9 through 11.)
To Turn IntelliMute Pro On
While no signal
is being detected,
press and hold
both
the
IntelliMute
and
City
buttons for
four seconds.
Tone
Visual Display
Two beeps
c or h will blink
To Turn IntelliMute Pro Off
Press and hold
both
the
IntelliMute
and
City
buttons for
four seconds.
Tone
Visual Display
One beep
c or h will show steady
IntelliMute Pro On
X K Ka
V
S
c
IntelliMute Button
City Button
Press and hold both
buttons simultaneously
To Turn Pop Alert On and Off
While no signal is
being detected, press
and hold both the
Dim
and
City
buttons
for four seconds.
Tone
Visual Display
Pop On = Two beeps
P
will blink twice in the display
Pop Off = One beep
P
will blink once in the display
CAUTION
When IntelliMute Pro is On,
NO
radar signals will be detected and
NO
alerts will be given at RPMs
below
the IntelliMute activation point.
XRS9370_MANL:9492-XRS9330 8/17/10 3:44 PM Page 12
Detection
Your Detector
Nothing
Comes Close to a Cobra
®
15
Detection
•
Signals Detected
The tables on the following pages show you the types of
Signals
your
detector will detect, as well as the visual alerts it provides for each of them.
Audio Alerts
A distinctly different
Alert
tone is used for each type of signal detected
(including separate tones for each laser signal). For X, K, Ka and Ku band
radar signals, the tones will repeat faster as you approach the signal
source. The repeat rate of the tones gives you useful information about
the signal detected. (See responding to alerts on page 18.)
Visual Display
An indication of the type of signal detected will appear in the UltraBright
data
Display
. During X, K, Ka and Ku alerts, a number will also appear,
indicating the strength of the signal detected. (1 = weakest, 5 = strongest)
During pop alerts, the letter
P
will
appear; and during laser alerts,
the letter
L
will appear, instead of
the signal strength indication.
During VG-2 or Spectre I or IV+
alerts, the letter
V
will appear.
It will be steady during VG-2
and blink during Spectre I or IV+.
During Safety Alert the letter
S
will appear.
Settings
Your Detector
X Signal Detected
X
K Ka V S
2
X
K
Ka V S
3
X K
Ka
V S
5
X K
Ka V S
4
Laser Signal Detected
X K Ka V S
L
VG-2 Alert Signal
Detected
X K Ka
V
S
c
K Signal Detected
Ka Signal Detected
Ku Signal Detected
Safety Alert Signal Detected
X K Ka V
S
c
Spectre I or IV+ Alert
Signal Detected
X K Ka
V
S
c
14 English
To Turn Ku Band On and Off
While no signal is
being detected, press
and hold the
City
button for four
seconds.
Tone
Visual Display
Ku On = Two beeps
X
and
K
will blink twice in the display
To Turn K Band On and Off
While no signal is
being detected, press
and hold both the
Mute
and
City
buttons
for four seconds.
Tone
Visual Display
K On = Two beeps
K
will blink twice in the display
K Off = One beep
K
will blink once in the display
Ku Off = One beep
X
and
K
will blink once in the display
Radar Alert Settings
The detector allows you to choose whether it will show
alerts on the X, K and
Ku bands
. The factory settings are: X Band and K Band On; Ku Band Off.
To Turn X Band On and Off
While no signal is
being detected, press
and hold both the
Dim
and
Mute
buttons
for four seconds.
Tone
Visual Display
X On = Two beeps
X
will blink twice in the display
POP Signal Detected
X K Ka V S
P
X Off = One beep
X
will blink once in the display
XRS9370_MANL:9492-XRS9330 8/17/10 3:45 PM Page 14
Detection
Your Detector
Nothing
Comes Close to a Cobra
®
17
Detection
Your Detector
English
16
Radar Signals and Visual Displays
Type of Signal
Visual Display
X Band Radar
X
and Signal Strength
K Band Radar
K
and Signal Strength
Ka Band Radar
Ka
and Signal Strength
Ku Band Radar
X K
and Signal Strength
Pop Radar
P
is Steady
Laser Signal Detected
X K Ka V S
L
Laser Signals and Visual Displays
Type of Signal
Visual Display
LTI 20-20*
L
is Steady
LTI Laser*
L
is Steady
Kustom Signals Laser 340*
L
is Steady
Kustom Signals Laser*
L
is Steady
Stalker LIDAR*
L
is Steady
Laser Atlanta SpeedLaser/Kustom Signals-ProLaser II*
L
is Steady
* Your detector provides 360° detection of these signals.
Safety Alert Signals and Visual Displays
Type of Signal
Visual Display
Emergency Vehicles
S
is Steady
Road Hazards
S
is Steady
Trains
S
is Steady
Safety Alert Signal Detected
X K Ka V
S
c
VG-2 and Spectre I or IV+ Alert Signals and Visual Displays
Type of Signal
Visual Display
Interceptor VG-2
V
is Steady
Spectre I or IV+
V
Blinks
VG-2 Alert Signal Detected
X K Ka
V
S
c
Spectre I or IV+ Alert Signal Detected
X K Ka
V
S
c
NOTE
Beep rate changes with different laser alerts.
NOTE
There are different tones for each Safety Alert.
NOTE
There are different tones for each alert.
X Signal Detected
X
K Ka V S
2
X
K
Ka V S
3
X K
Ka
V S
5
X K
Ka V S
4
K Signal Detected
Ka Signal Detected
Ku Signal Detected
POP Alert Signal Detected
X K Ka V S
P
XRS9370_MANL:9492-XRS9330 8/17/10 3:45 PM Page 16
Description
Interpretation
Recommended
Response
Tone repeats slowly at
first, then speeds up
rapidly.
Probably police radar.
FULL ALERT
Tone sounds one
time only.
Probably a false alarm,
but possibly pulsed radar,
VG-2, or Spectre I or IV+
nearby.
Exercise caution
Tone instantly begins
repeating rapidly.
Radar, VG-2 or Spectre I
or IV+ nearby has been
activated suddenly.
FULL ALERT
Tone repeats slowly as you
approach a hill or bridge,
then speeds up sharply as
you reach it.
Probably police
radar beyond the
hill or bridge.
FULL ALERT
Tone repeats slowly
for a short period.
Probably a false alarm.
Exercise caution
Any type of laser alert.
Laser alerts are
never false alarms.
FULL ALERT
Any Safety Alert.
You are nearing an
emergency vehicle,
railroad crossing,
or road hazard
(construction,
accident, etc.).
Exercise caution
Understanding Radar and Laser
Your Detector
Nothing
Comes Close to a Cobra
®
19
Understanding Radar and Laser
•
Radar Speed Monitoring Systems
Three band frequencies have been approved by the Federal Communications
Commission (FCC) for use by speed monitoring radar equipment:
X band
10.525 GHz
K band
24.150 GHz
Ka band
33.400 – 36.00 GHz
Your detector detects signals in all three radar bands, plus Ku band (13.435 GHz),
which is an approved frequency used in parts of Europe and Asia.
VG-2 and Spectre I & IV+
VG-2
and
Spectre I & IV+
are radar detector detectors (RDDs) that work by
detecting low-level signals emitted by most radar detectors. Your detector
does not emit signals that can be spotted by VG-2 and Spectre I RDDs.
However, your detector
can
be spotted by Spectre IV+ RDDs. Your unit
detects signals from these or similar devices and will alert you when such
a device is in use near your vehicle.
Safety Alert Traffic Warning System
FCC-approved
Safety Alert
transmitters emit microwave radar signals that
indicate the presence of a safety-related concern. Depending on the frequency
of the signal emitted, it can indicate a speeding emergency vehicle or train,
or a stationary road hazard.
Because these microwave signals are within the K band frequency, most
conventional radar detectors will detect Safety Alert signals as standard
K band radar. Your detector, however, is designed to differentiate between
standard K band and Safety Alert signals, and give separate alerts for each.
Safety Alert technology is relatively new. Safety Alert transmitters can
be found in limited numbers in all 50 states, but the number is growing.
Depending on your location, you may not receive these alerts regularly
and may often encounter emergency vehicles, trains and road hazards
without being alerted. As the number of transmitters increases,
these alerts will become more common.
When you receive such an alert, please watch for emergency vehicles ahead
of you, on cross streets and behind you. If you see an emergency vehicle
approaching, please pull over to the right side of the road and allow it to pass.
Detection
Your Detector
English
Instant-On Detection
Your detector is designed to detect
Instant-On
speed monitoring signals,
which can suddenly appear at full strength.
NOTE
You should take appropriate action immediately
whenever an instant-on alert is given.
Responding to Alerts
18
XRS9370_MANL:9492-XRS9330 8/17/10 3:45 PM Page 18
Nothing
Comes Close to a Cobra
®
21
Understanding Radar and Laser
and Maintenance
Your Detector
English
LIDAR (Laser)
The correct name for the technology that most people refer to as
laser is actually
LIDAR
, which stands for Light Detection and Ranging.
LIDAR operates much like radar. Its signal spreads out like a radar signal, though
not as widely. Unlike radar, LIDAR must have a clear line of sight to its target
vehicle throughout the entire measurement interval. Obstructions such as sign
posts, utility poles, tree branches, etc., will prevent valid speed measurement.
Some common questions about LIDAR include:
■
Does weather have any affect on LIDAR?
Yes. Rain, snow, smoke, fog or airborne dust particles will reduce the
effective range of LIDAR and can, if dense enough, prevent its operation.
■
Can LIDAR operate through glass?
Yes. Newer LIDAR guns can obtain readings through most types of glass.
However, the laser pulse also can be received through glass to trigger
an alarm by your detector.
■
Can LIDAR operate while in motion?
No. Because LIDAR operates by line of sight, the person using it cannot
drive the vehicle, aim and operate the gun all at the same time.
■
Is LIDAR legal to use?
Yes. It is legal in all 50 states.
Maintenance
•
Maintenance of Your Radar Detector
Your detector is designed and built to give you years of trouble-free performance
without the need for service. No routine
Maintenance
is required.
If your unit does not appear to be operating properly, please follow these
troubleshooting steps:
■
Make sure the power cord is properly connected.
■
Make sure the socket of your vehicle’s cigarette lighter is clean and
free of corrosion.
■
Make sure the power cord’s cigarette lighter adapter is firmly seated
in your cigarette lighter.
■
Check the power cord fuse. (Unscrew the ribbed end cap of the
cigarette lighter adapter and examine the fuse. If required, replace
it with a 2-amp fuse only.)
20
Specifications
Your Detector
Specifications
•
Band and Frequencies
Band
Frequencies
X Band
10.525
± 0.050
GHz
K Band
24.125
± 0.125
GHz
Ka Band
34.700
± 1.300
GHz
Ku Band
13.435
± 0.035
GHz
VG-2
11.500
± 0.250
GHz
Laser
910± 50nm
100
PPS
910± 50nm
125
PPS
910± 50nm
130
PPS
910± 50nm
200
PPS
910± 50nm
238
PPS
910± 50nm
340
PPS
Spectre I
13.300
± 0.200
GHz
Spectre IV/IV+
Not Disclosed
Safety Alert
24.070
± 0.010
GHz
Traffic Warning
24.110
± 0.010
GHz
System
24.190
± 0.010
GHz
24.230
± 0.010
GHz
This radar detector is covered by one or more of the following U.S. patents:
5,497,148; 5,594,432; 5,612,685; 6,078,279; 6,094,148. Additional patents
may be listed inside the product or pending.
XRS9370_MANL:9492-XRS9330 8/17/10 3:45 PM Page 20
Product Service
Customer Assistance
Nothing
Comes Close to a Cobra
®
23
Warranty
English
22
Limited 1-Year Warranty
•
For Products Purchased in the U.S.A.
Cobra Electronics Corporation warrants that its Cobra Radar/Laser Detectors,
and the com po nent parts thereof, will be free of defects in workmanship and
materials for a period of one year from the date of first consumer purchase.
This war ran ty may be enforced by the first consumer pur chas er, pro vid ed that
the product is utilized within the U.S.A.
Cobra will, without charge, repair or replace, at its option, de fec tive
Radar/Laser Detectors, products or com po nent parts upon de liv ery to the
Cobra Factory Service Department, ac com pa nied by proof of the date of first
consumer pur chase, such as a du pli cat ed copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for
warranty service, but the return charges will be at Cobra’s expense, if the
product is repaired or replaced under warranty.
This warranty gives you specific rights, and you may also have other rights
which vary from state to state.
Exclusions: This limited warranty does not apply:
1.
To any product dam aged by accident.
2.
In the event of misuse or abuse of the product or as a result
of un au tho rized alterations or repairs.
3.
If the serial number has been altered, defaced or re moved.
4.
If the owner of the product resides outside the U.S.A.
All implied warranties, including war ran ties of mer chant abil i ty and fitness for
a par tic u lar purpose are limited in duration to the length of this warranty.
Cobra shall not be liable for any incidental, con se quen tial or oth er dam ag es;
including, without lim i ta tion, damages re sult ing from loss of use or cost of
in stal la tion.
Some states do not allow limitations on how long an implied warranty lasts
and/or do not allow the ex clu sion or limitation of incidental or con se quen tial
dam ag es, so the above lim itations may not apply to you.
Warranty
Product Service
•
For any questions about operating or installing this new Cobra product, or if
parts are missing…
PLEASE CALL COBRA FIRST…
do not return this
product to the store. See customer assistance on page A1.
If this product should require factory service, please call Cobra first at
773-889-3087 BEFORE sending the product. This will ensure the fastest
turnaround time on any repair.
If Cobra asks that the product be sent to its factory, the following must be
furnished to have the product serviced and returned:
1.
Send the complete unit, including power cord. (It is not necessary
to include the mounting bracket.)
2.
For warranty repair, enclose some form of proof-of-purchase,
such as a photocopy or carbon copy of a sales receipt. If you
send the original receipt, it cannot be returned.
3.
Enclose a typed or clearly written description of the problem
you are having with your unit, plus the name and address where
you want the unit returned.
4.
Pack the unit securely to prevent damage during transit. If possible,
use the original packing materials.
5.
Ship prepaid and insured using a traceable carrier such as United Parcel
Service (UPS), Federal Express or Insured Priority mail with delivery
confirmation. Ship to: Cobra Factory Service, Cobra Electronics
Corporation, 6500 West Cortland Street, Chicago, IL 60707 U.S.A.
6.
Please allow three to four weeks before contacting us about the status
of your service. Call 773-889-3087 for assistance. If your unit is under
warranty, it will either be repaired or replaced upon receipt, depending
on the model. If your unit is out of warranty, you will receive a letter
informing you of the repair or replacement charge.
XRS9370_MANL:9492-XRS9330 8/17/10 3:45 PM Page 22
Optional Accessories
English
Optional Accessories
•
You can find quality Cobra products and accessories
at your local Cobra dealer, or in the U.S.A., you can
order directly from Cobra. See ordering info on page 25.
24
Windshield Mounting Bracket
Includes suction cups
Item # 545-159-N-001
Straight 12V DC Power Cord
Includes plug and fuse
Item # 420-030-N-001
Coiled 12V DC Power Cord
Includes plug and fuse
Item # 420-026-N-001
Dual Port Power Adapter
Includes adjustable plug
(up to 90°) and fuse
Item # CLP-2B
Customer Assistance
XRS9370_MANL:9492-XRS9330 8/17/10 3:45 PM Page 24