Full Text Searchable PDF User Manual
REVISON 2:09/26/2012
REVISON 0:01/08/2010
PAGE 1 OF 6
460231(B1&B2)
TWIN/TWIN BUNK BED
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com
REVISON 1:07/16/2012
AR
RIGHT UPPER BED
END
1PC
G
BED SLAT
12PCS
BL
LEFT UPPER BED
END
1PC
H
SQUARE TRESTLE
BAR
1PC
C
LOWER BED END
2PCS
I
FLAT TRESTLE BAR
3PCS
D
BED RAILWITHOUT
HOLE
2PCS
J
LEFT LADDER STILE
1PC
D1
BED RAILWITH
HOLE
2PCS
K
RIGHT LADDER
STILE
1PC
E
LONG GUARDRAIL
2PCS
L
LADDER STEP
4PCS
F
SHORT
GUARDRAIL
2PCS
1
LONG BOLT
24PCS
5
LONG WOOD SCREW 24PCS
2
BARREL NUT
24PCS
6
METAL PIN
4PCS
3
SHORT BOLT
14PCS
7
ALLEN WRENCH
1PC
4
ALLEN CAP SCREW
8PCS
8
WOOD DOWEL
16PCS
9
SHORT WOOD
SCREW
2PCS
www.coastercompany.com
PAGE 2 OF 6
ITEM :
460231 (B1&B2)
HARDWARE IDENTIFICATION
PARTS IDENTIFICATION
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequencs as numbered to assure fast & easy assembly.
!
Warning!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact
the store immediately.
2. This product is for home use only and not intended for commercial establishment
ITEM :
460231(B1&B2)
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
Insert wood dowels to both ends of bed rail without hole.
Align and fasten bed rails to lower bed end using long bolt
and barrel nut and tighten with Allen wrench
Align and fasten bed slats to bed rail using long wood
screw and tighten with screw driver ( not included).
STEP 3
STEP 4
3.1 Align and fasten flat trestle bar to bed rail with hole and
long guardrail by using short bolt and tighten with Allen
wrench.
3.2 Align and fasten short guardrails to square trestle bar
using barrel nut and long bolt and tighten with Allen wrench
3.3 Align and fasten square trestle bar to bed rail with hole
using short bolt and tighten with Allen wrench
3.4 Align and fasten flat trestle bar to short guardrail and
bed rail with hole using short bolt and tighten with Allen
wrench.
Insert wood dowel to both ends of bed rails with holes.
Align and fasten guardrails and bed rail with hole to
upper left and right bed end using long bolt and tighten
with Allen wrench.
www.coastercompany.com
PAGE 3 OF 6
ITEM :
460231 (B1&B2)
ASSEMBLY INSTRUCTIONS
STEP 5
STEP 6
Align and fasten bed slats to bed rail with hole by using long
wood screw and tighten with screw driver( not included).
Align and fasten ladder stiles to ladder step using Allen
cap screw and tighten with Allen wrench.
STEP 7
STEP 8
Insert metal pin to the top of lower bed ends, then align and
place the upper bed end onto the pin.
Align and fasten the ladder to bed rail using short wood
screw and tighten with screw driver( not included).
www.coastercompany.com
PAGE 4 OF 6
1
Follow the information on the warning attached to the upper bunk end structure and on the carton. Do
not remove this label.
2
Always use the recommended size mattress or mattress support or both to help prevent the likelihood of
entrapment or falls.
3
Surface of mattress must be at least five inches (127mm) below the upper edge of guardrails.
4
Do not allow children less than six years of age to use the upper bunk.
5
Prohibit more than one person on upper bunk.
6
Periodically check and ensure that the guardrail, ladder and other components are in their proper
position, free from damage, and that all connectors are tight.
7
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8
Always use the ladder for entering and leaving the upper bunk.
9
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10
Use of a night light may provide added safety precaution for a child using upper bunk.
11
If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12
Always use guardrails or both long sides of the upper bunk.
13
The use of water or sleep flotation mattress is prohibited.
14
Keep these instructions for future reference.
STRANGULATION HAZARD:
15
Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
example, but not limited to hooks, belts, and jump ropes.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress which is 37 ½” – 38 ½” in width and 74” – 75” in length. The total thickness of
mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 6”
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS:
Replacement parts, including additional guardrails may be obtained from any COASTER Furniture
Dealer.
SAFETY WARNING
Coaster puts your child’s safety as a Top Priority. Our bunk beds have been tested by an independent laboratory
and are certified to be in compliance with ASTMF-1427, “Standard Consumer Safety Specification for Bunk
Beds” and U.S. Government specifications 16 Code of Federal Regulations, parts 1213 and 1513.
PAGE 5 OF 6
www.coastercompany.com
1. When using beds as bunk beds, the ladder MUST be securely
attached to the upper bunk rail at all times.
2. When using the beds as two (2) separate floor-standing beds,
the ladder MUST be stored in a separate location where children
cannot use the ladder in any manner.
3. DO NOT use, nor permit children to use, the ladder in any
manner whatsoever, other than to access the top unit when
used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
4. Any misuse or unauthorized use of the ladder could result in
serious or fatal injury.
5. Failure to follow the above WARNING, and/or failure to follow
assembly instructions completely, will void any and all liability
of COASTER COMPANY OF AMERICA for damages and injury to
persons and property.
www.coastercompany.com | 877- COASTER (262-7838)
PAGE 6 OF 6
www.coastercompany.com