Full Text Searchable PDF User Manual
1
Assembly & Operating Instructions
for
Magnetic Stepper
1
COMPLETE BIKE ASSEMBLY
2
PARTS LIST
NO
DESCRIPTION
Q’TY
NO
DESCRIPTION
Q’TY
1
Main Frame
1
48
Washer 19 x 8
4
2
Foot Tube
2
49
Screw M8 x 10L
4
3
Stabilizer
1
50
Cap
2
4
Handlebar Post
1
51
Φ
25 C Clip
2
5
Pulley I
1
52
O-Ring
4
6
Pulley II
1
53
Sensor plate
1
7
Magnetic System
1
54
Magnet
1
8
Bearing Housing
2
55
Screw
φ
8 x 33.5L
8
9
Belt I
1
56
Screw M6 x 12L
8
10
Belt II
1
57
Screw M8 x 10L
4
11
Bearing Hub
2
58
Washer 19 x 8
4
12
Spacer
φ
25 x 28 x 8.5L
8
59
M5 Nylock nut
3
13
Screw M8 x 45L
8
60
Handpulse sensor wire
1
14
Washer 19 x 8 x 1.5T
8
61
Screw M5 x 50L
1
15
M8 Nylock Nut
1
62
Sensor wire I
1
16
Axle
1
63
Sensor wire II
1
17
Key 6 x 6 x 15L
1
64
Screw 4 x 12
2
18
Screw M8 x 12L
1
65
Screw 4 x 25
2
19
Washer 12 x 16 x 1T
1
66
Handpulse sensor
2
20
Nut 3/8 x 26t x 3T
4
67
Motor sensor wire
1
21
Nut 3/8 x 26t
2
68
Screw M5 x 40L
1
22
Spring
φ
20 x 16 x 2 x 40L
1
69
Screw M5 x 12L
4
23
Idle Wheel II
1
70
Foam Grip
2
24
Nut 3/8 x 26t
2
71
Meter
1
25
Spring
φ
20 x 16 x 2 x 70L
1
72
Top Cover
1
26
Idle Wheel I
1
73
Bushing
φ
76
1
27
C Clip #19
4
74
Left Cover
1
28
Rubber stopper
2
75
Right Cover
1
29
C clip #13
4
76
Screw M5 x 12L
2
30
M8 Nylock Nut
2
77
Screw 4 x 12
2
31
Moving wheel
2
78
Screw 4 x 16
3
32
Screw M8 x 35L
2
79
Screw 4 x 12
4
33
Cap
2
80
Rubber stopper
2
34
Spacer
φ
19 x 12 x 60.5L
4
81
35mm Plug
2
35
Chain
2
82
Tension cable
1
36
Chain-Spring connector
2
83
Tension Gear box
1
37
Spring
2
84
Screw M5 x 10L
2
38
Spring connector
2
85
Foam grip
2
39
Screw M10 x 55L
2
86
Handrail – top (Right + Left)
1
40
M10 Nylock Nut
2
87
Handrail – bttom (Right + Left)
1
41
Spacer
φ
16 x 10 x 40L
2
88
AC Adaptor
1
42
Pedal fixing plate
2
43
Screw M12 x 85L
4
TOOL
44
M12 Nylock nut
4
Allen Key 6mm
1
45
Screw M6 x 20L
8
Allen Key 5mm
2
46
Rubber stopper
2
Screw driver
1
47
Pedal
2
3
ASSEMBLY
INSTRUCTIONS
STEP 1.
ASSEMBLING THE STABILIZER (3) UNTO MAIN
FRAME BY SCREN (49) & WASHER (48).
STEP 2.
SLIDE THE TOP COVER (72) INTO HANDLEBAR
POST (4). CONNECT THE SENSOR WIRE (67) &
(63) TOGETHER. SLIDE HANDLEBAR POST ONTO
MAIN FRAME. FIXING THEM TOGETHER BY
SCRENS (57) & WASHERS (58) SLIDE TOP COVER
TO BOTTOM POSITION.
4
STEP 3.
ASSEMBLING THE HANDRAIL ONTO THE FRAME
BY SCREWS (55) ,(56) & (64).
STEP 4.
CONNECTING THE SENSOR WIRES (60) & (63)
ONTO COMUTER. FIXING COMPUTER ONTO
HANDLEBAR POST BY SCREWS (69).
5
EXERCISE MONITER INSTRUCTION MANUAL BC-51126
FRONT VIEW
MANUAL
FAT BURN
VALLEY
INTERVALS
SACN
TIME
RPM
COUNT
CAL
PULSE
KEY GUIDE
ENTER/MODE:
1.
Press this button to enter the function setting from Time, Distance, Calorie, and pulse limit.
2.
Press this button to confirm the setting values.
UP : 1. Press this button to select the program form Manual and Program 1 to Program 6.
2. Increase the setting value of Time, Distance, Calories, and Pulse Limit.
3. Increase the resistance level.
DOWN : 1. Press this button to select the program form Manual and Program 6 to Program 1.
2. Decrease the setting value of Time, Distance, Calories, and Pulse Limit.
3. Decrease the resistance level.
6
START/STOP:
1. Press this button to start or stop exercising.
2. Hold this button for 2 seconds can enter initial mode and reset value to zero.
POWER UP
1.
Before all, you should connect the connection cables with monitor together.
2.
If the power source is coming form ADAPTOR (6V 1A), plug in the ADAPTOR.
When stop exercising, please remember to unplug the ADAPTOR. (6V 1A)
3.
After power up, all LCD segments will light up for 2 seconds & CPU will be reset the resistance
into level 0. And then the system goes into the initial mode.
FUNCTIONS AND OPERATIONS
· AUTO ON/OFF
The monitor will wake up automatically if the exercise machine is in motion. If stop exercising for over 4
minutes, monitor will turn off and reset all function values to zero.
SCAN
While at “start” operation,
Press the MODE button until mark appear on the position of Scan. Monitor will display the following
function and each function will keep 5 seconds on the main screen. Time–Speed-Distance–Calorie–Pulse.
TIME
Press the MODE button until the mark appearance on the position of TIME. Monitor will display the
Time function on the main screen.
Count up:
Without setting the time value, the monitor will count up the time from 00:00~99:59.
Count down:
Setting the exercise time from 1:00~99:00 minutes, the monitor will count down from your setting values.
Once reach setting value, monitor will alarm.
RPM
Press the MODE button until the mark appearance on the position of RPM. Monitor will display the
current RPM on the main screen. The monitor will display the current RPM from 0 ~ 999 rpm/min
COUNT
Press the MODE button until the mark appearance on the position of COUNT. Monitor will accumulate
the distance trip.
7
CALORIE
Press the MODE button until the mark appear on the position of Calorie.
Count up:
Without setting the calorie value, the monitor will count up the calorie from 0.1~999.0.
Count down:
Setting the exercise calorie from 1.0~999.0, the monitor will count down from your setting values. Once
reach setting value, monitor will alarm.
PULSE (Target Heart Rate)
Pulse Limit:
Setting the value of pulse limit between 90 to 220, the monitor will measure your heartbeats. Once reach
setting value, monitor will produce beep sounds to remind you.
NOTE:
1.
If no pulse signal input within 16 seconds, the display will indicate “P”.
2.
In the stop mode, the monitor can not measure heart rate.
OPERATION:
This system contains one manual and 6 programs. You can preset the workout time and system will divide the
time by 10 intervals. If you don’t preset workout time, system will count up the workout time in one-second
increment.
DETAIL OPERATION OF MANUAL AND PROGRAM 1
st
– PROGRAM 6
th
:
1. Setting the value of Time and/or Distance and/or Calories and/or Pulse
a.
Press the UP or DOWN button to choose desired program from Manual. Program 1 to program 6.
b.
Press the ENTER button to confirm your desired program.
c.
The time window will flash.
d.
Press the UP or DOWN button to set up your workout time.
e.
Press the ENTER to confirm your setting value.
f.
The distance window will flash.
g.
Press the UP or DOWN button to set up the distance value.
h.
Press the ENTER to confirm your setting value
i.
The Calorie window will flash
j.
Press the UP or DOWN button to set up the calorie value.
k.
Press the ENTER to confirm your setting value
l.
The Pulse window will flash
m.
Press the UP or DOWN button to set up the pulse value
n.
Press the ENTER to confirm your setting value
o.
Press start to begin the exercise.
8
2. Without setting the value of time, distance, calories and pulse
a.
Press the UP or DOWN button to choose desired program from Manual. Program 1 to program 6.
b.
Press the ENTER button to confirm your desired program.
c.
Press start to begin the exercise.
Note: Program 6 is a very unique program, it allows the monitor to adjust the workout resistance according to
your heart rate automatically. If your present heart rate is greater than your target heart rate, CPU will decrease the
workout resistance automatically. If your present heart rate is smaller than your target heart rate, CPU will increase
workout resistance.
