Full Text Searchable PDF User Manual
CX-A6 Amplifier
Installation & User Guide
V9.0
Cloud Electronics Limited
140 Staniforth Road, Sheffield, S9 3HF England
Tel + 44 (0) 114 244 7051
Fax + 44 (0) 114 242 5462
info@cloud.co.uk
Web site http://www.cloud.co.uk
CX-A6
I
NSTALLATION AND OPERATION MANUAL
1
15-01-09 V9
Model CX-A6 Multi-Channel Amplifier
Installation and operation manual
Contents
Section
Page
1
Safety Notes ............................................................................... 2
2
General Description ................................................................... 2
3
Installation .................................................................................. 2
4
Input Facilities ............................................................................ 2
5
Output Details ............................................................................ 4
6
100V Line operation ................................................................... 4
7
Configuring the CX-A6 for 100V Line operation ......................... 5
8
Bridged Mode Operation ............................................................ 5
9
Status Indicators ......................................................................... 5
10
VCA Modules ............................................................................. 6
11
Remote Level Plate Connections ............................................... 6
12
Bose
Equalisation Modules ...................................................... 7
13
Installing Optional Modules ........................................................ 7
14
Field Servicing ............................................................................ 8
15
General Specifications ............................................................... 9
16
Technical Specifications ............................................................. 9
CX-A6
I
NSTALLATION AND OPERATION MANUAL
2
15-01-09 V9
1
Safety Notes
•
Do not expose the unit to water or moisture
•
Do not expose the unit to naked flames.
•
Do not block or restrict any air vent
•
Do not operate the unit in ambient temperatures above 35
o
C
•
Do not touch any part or terminal carrying the hazardous live symbol ( ) )
while power is supplied to the unit.
•
Do not perform any internal adjustments unless you are qualified to do so and
fully understand the hazards associated with mains operated equipment.
•
The unit has no user serviceable parts. Refer any servicing to qualified service
personnel.
•
If the moulded plug is cut off the lead for any reason, the discarded plug is a
potential hazard and should be disposed of in a responsible manner.
For more detailed information refer to the rear of the manual.
2
General Description
The CX-A6 is a six-channel power amplifier with a maximum output of 120 watts into
loads of 4 ohms per channel. The unit features extremely low distortion and low noise
together with a high slew rate. Full circuit protection is provided and the load is
disconnected if the heat sink overheats or any DC is detected at the output. A five-second
switch-on delay operates to avoid any switching thumps or other extraneous signals
reaching the speaker system.
All six input amplifiers are balanced and connect via 3 pin XLR type connectors with
adjacent level controls, all mounted on the rear panel. Input signal routing switches are
provided and allow the unit to operate in many configurations whilst retaining simple input
connections. The CX-A6 amplifier can be used with up to three optional plug-in two
channel VCA modules to provide remote level control. Each plug-in module can operate
as two individual attenuators or can be linked to operate as a stereo pair with one remote
level control.
3
Installation
The CX-A6 is suitable for mounting in a standard 19" equipment rack and occupies two
units of rack space. Sufficient ventilation must be provided for the unit. The amplifier
draws cool air through the front panel and exhausts through the right side and care must
be taken not to obstruct the airflow otherwise the unit may intermittently turn off due to the
built-in thermal protection. Applications that require long, sustained operation at high
power levels should allow a 1U space above and below the unit. The unit is 325mm deep
but a depth of 400mm should be allowed to clear the connectors.
4
Input Facilities
All six inputs are balanced and use 3 pin XLR type connectors. All inputs are wired to the
standard convention of pin 1 ground, pin 2 in-phase, pin 3 reverse phase, with the shell of
the connector connected to the chassis. If the unit is operating in a location which has a
high level of electrical or magnetic disturbance or is close to a TV or radio transmitter, we
suggest that the input cable screen be connected to the shell of a metal XLR type
connector. If the signal is from an unbalanced source, connect pin 3 to pin 1 (ground)
inside the XLR type connector and use pin 2 as hot.
Each input has a level control adjacent to the respective XLR type connector. Input
switching is provided on input channels 2 to 5 allowing a wide variety of input routing
configurations. See the schematic diagrams showing details of various routing
possibilities. With all input switches depressed, the unit operates as six independent
amplifiers. Three stereo pairs, driven from one stereo source and six channels driven
from one mono source are also possible together with a combination of the two by
suitably configuring the input routing switches.
CX-A6
I
NSTALLATION AND OPERATION MANUAL
3
15-01-09 V9
1
2
3
4
5
6
1
2
1
3
2
4
1
5
2
6
INPUT 1
1
2
3
4
5
6
POWER
AMPLIFIER
LEVEL
CONTROL
SOURCE
SWITCHES
INPUT
AMPLFIER
FROM MONO SOURCE
SIX CHANNELS DRIVEN FROM ONE MONO SOURCE
1
2
3
4
5
6
1
2
1
3
2
4
1
5
2
6
INPUT 1
1
2
3
4
5
6
POWER
AMPLIFIER
LEVEL
CONTROL
SOURCE
SWITCHES
INPUT
AMPLFIER
FROM STEREO SOURCE
THREE STEREO PAIRS DRIVEN
FROM ONE STEREO SOURCE
INPUT 2
CX-A6
I
NSTALLATION AND OPERATION MANUAL
4
15-01-09 V9
5
Output Details
Six 2-pole plug-in screw terminal type connectors (5mm pitch) are provided on the rear
panel for the four speaker outputs; these can accommodate flexible leads up to 2.50mm².
The plugs for these connectors are provided in the accessory pack. If you require
replacement plugs the Cloud part number is TP955188.
Do not make any connections to the unit with the power cable attached.
It is good practice to distance the output wiring from the input wiring and keep the
speaker wires twisted until they are terminated to reduce any cross-talk to a minimum
level.
6
100V Line operation
Connecting a CXL-100T 100W 100V-line module across an output of the CX-A6 will
obtain a 100W 100V-line output from that channel. The CXL-100T has to be mounted
externally of the amplifier. A 2U 19" rack panel (CXL-800) is available that accommodates
up to eight CXL-100T transformer modules.
Using at least 1.5 mm² cable, wire the output of the amplifier to the 2 pole connector and
connect to the CXL-100T ‘AMPLIFIER’ terminations observing polarity. The 70V/100V-line
output uses the 3 pole connector; for 70V speakers, use the 0V (-) and 70V (+)
terminations and for 100V speakers use the 0V (-) and 100V (+) terminations. The
speaker cable must be at least 0.75mm², double insulated. With long distances it may
advantageous to use thicker cable. The CXL-100Tprovides a fully balanced output signal
which is isolated from the amplifier.
The following page contains important information on configuring the CX-A6’s 65Hz filters
1
2
3
4
5
6
1
2
1
3
2
4
1
5
2
6
INPUT 1
1
2
3
4
5
6
POWER
AMPLIFIER
LEVEL
CONTROL
SOURCE
SWITCHES
INPUT
AMPLFIER
SIX CHANNELS OPERATING AS INDEPENDENT AMPLIFIERS
INPUT 2
INPUT 3
INPUT 4
INPUT 5
INPUT 6
CX-A6
I
NSTALLATION AND OPERATION MANUAL
5
15-01-09 V9
7
Configuring the CX-A6 for 100V-line Operation
When a CXL-100 is connected to a channel of the CX-A6, that channel must have its
65Hz high-pass filter operational. Without this filter operational, the presence of high
input levels at frequencies below 50Hz may result in transformer saturation causing the
amplifiers VI limiter to operate. The filter can be switched on by moving the relevant
jumper to the ‘IN’ position.
Jumpers J1-6 are associated with the channels of the CX-A6 as follows:
J1
= Zone 1
J2
= Zone 2
J3
= Zone 3
J4
= Zone 4
J5
= Zone 5
J6
= Zone 6
Diagram to Show Location of J1-6 on the CX-A6 PCB
8
Bridged Mode Operation
The unit can operate in Bridged Mode using any two channels. The inputs must be wired
together by linking the input signal at the XLR connectors of the two relevant channels,
wiring the "second" input out of phase (i.e. pin 1 ground, pin 3 in-phase, pin 2 reverse
phase). The input level controls of the two channels should both to be set to the fully
clockwise position.
The output load should then be connected between the terminals marked “CHx” (where
“x” represents the channel number) of the output connectors of the relevant channels.
There is no connection to the terminals marked “0V” of the relevant channels.
You must ensure that the positive wire is connected to the terminal marked “CHx” of the
“first” channel used. The negative wire is connected to the terminal marked “CHx” of the
“second” channel used, i.e. the channel with its input connected out of phase.
Thus for example it is possible to configure four of the available channels as two bridged
outputs allowing a stereo input to be delivered to two 240 watt 8 ohm outputs.
9
Status Indicators
The front panel of the CX-A6 has an array of LED’s that indicate the status of all six
channels. The lower green LED illuminates when a signal exceeding 500mW is detected,
the yellow 'peak' LED will illuminate when the amplifier output is close to clipping and the
top red LED indicates that the protection relay has disconnected the load. Please note
that it is normal for all six red LED's to illuminate for approximately five seconds when the
unit is switched on, indicating operation of the switch-on delay circuitry. The lower green
LED indicates that the power is switched on.
CX-A6
I
NSTALLATION AND OPERATION MANUAL
6
15-01-09 V9
10
VCA Modules
A two-channel VCA module is available as a plug-in option for the CX-A6 (see section 13
for installation details) and can be used with either one or two control plates. The unit can
operate two channels independently or switched to provide stereo attenuation via one
control plate. For independent operation, the switch should be in the 'solo' position (in),
with the remote level controls connected to both 3 pin connectors. For stereo operation,
position the switch in the link position (out) and connect the level control to the left
connector only. The RL-1 remote control plate is compatible with domestic electrical
accessories and can be mounted onto a standard British flush or surface mounted 25mm
deep back box. Two-core cable with overall screen should be used to connect the remote
level control to the module mounted inside the CX-A6. The circuitry uses the industry
standard 'Thats 2150A' VCA providing very low distortion and up to 90dB attenuation. The
VCA module can be wired to provide muting by using an auxiliary relay connected to a
fire alarm control panel.
Note:
A VCA module cannot be installed to channels that already have a Bose
equalisation module installed.
11
Remote Level Plate Connections
REAR VIEW OF CX-A6 AMPLIFIER
1 2 3
USE 2 CORE SCREENED CABLE
CONNECT SCREEN TO TERMINAL 1
REAR VIEW OF LEVEL CONTROL PLATE
LINK
REMOTE LEVEL
CLIP
PROTECT
OFF
ON
SOLO
1
2
1+2
1
2
SOURCE
1
2
3
1
2
3
1
2
CX-A6
I
NSTALLATION AND OPERATION MANUAL
7
15-01-09 V9
12
Bose
Equalisation Modules
Each channel on the CX-A6 can have Bose
equalisation so that its output will be
compensated correctly for a wide range of Bose
speakers.
Available Equalisation Modules:
-
Bose
®
Speaker models: M8, M16, M32, MA12, 402, 502A, 502B, 502BEX,
802, MB4, MB24, LT3202, LT4402, LT9402, LT9702
Bose
equalisation modules must be fitted to a stereo
EQ card adapter, Cloud part CA340166.The adapter is
a stereo fitting, so will cover two adjacent channels of
the amplifier. An equalisation module is required for
each channel that is to be equalised, and it is possible
to equalise a single channel using this module.
Note:
•
An EQ card adapter module cannot be installed to a
pair of channels with a VCA module installed.
13 Installing Optional Modules
There are three optional modules for the CX-A6, the VCA-2, the CA340166 Stereo EQ
card adapter for Bose
equalisation modules, and Bose
equalisation modules.
Components supplied with the various modules are listed below: -
VCA-2:
Two 40mm M3 hex spacers, one plastic insert & two 3-pin screw terminal plugs.
CA340166 Stereo EQ card adapter:
Two 25mm M3 hex spacers.
Bose
equalisation modules:
No additional components.
The CX-A6 connectors to install the VCA modules are to the rear of the amplifier on the
input PCB clearly marked on the PCB as ‘CON X TO VCA MODULE’ where ‘X’ is 1,2 or 3
see below: -
CON 1
= Channel 1&2
CON 2
= Channel 3&4
CON 3
= Channel 5&6
Follow the instructions below carefully when installing modules. Incorrect installation can
cause damage.
1. Turn the power off and remove mains cable.
2. Remove the top panel.
3. Select the CX-A6 connector you wish to install the module to (see notes above) and
remove the jumpers from it.
4. When installing a VCA-2, remove the relevant rear panel blanking plate.
5. When installing a VCA-2, push the plastic plug into the rear panel ‘clip protect’ hole.
6. Two M3 fixing screws can be found adjacent to the CX-A6 connector. Remove and
retain these two screws then fix the M3 hex spacers in their place.
7. Push the 10-way plug onto the CX-A6 connector with the plug aligned so the cable
approaches it from the rear of the chassis and check that the connector mates with all
10 pins (orientation diagrams can be seen on the following page).
8. When installing a VCA-2,
position the 3-pin sockets and switch of the VCA through the
cut-outs in the rear panel.
CX-A6
I
NSTALLATION AND OPERATION MANUAL
8
15-01-09 V9
9. Align the two holes in the module over the top of the two spacers.
10. Secure the module with the two M3x6 screws (removed earlier).
11. When installing a Bose
equalisation module to a stereo EQ adapter, remove the
adapter jumper link for the channel to be equalised and fit the Bose® EQ module to the
appropriate connector
12. When installing a Bose
equalisation module, configure the relevant 65Hz filter to ‘IN’
and connect a CXL-100T 100V line transformer (see section 6)
13. Fit the top panel.
Bose
Equalisation Module Orientation (Side View) VCA Module Orientation (Side View)
14
Field Servicing
The CX-A6 is ruggedly built and uses proven reliable circuitry. It requires no more than
the occasional removal of any dust that may have built up inside the unit as a result of the
forced cooling. In the unlikely event of failure, the power amplifier module (2 channels)
can be replaced without special tools and is available as a tested replacement complete
with heat sink. Proceed as follows to replace the power module:
Disconnect all the leads and connectors from the rear of the unit.
Ensure that the mains supply lead has been disconnected.
Remove the CX-A6 from the equipment rack.
Remove the top panel.
The power amplifier modules are arranged as three dual channel units.
Locate the faulty unit and remove both the 7 way power cable & the 10 way ribbon
connector.
Remove the four fixing screws from the bottom of the unit to release the module.
Now fit the replacement unit by proceeding in reverse order.
No setting up is required and the unit should operate normally.
CX-A6
I
NSTALLATION AND OPERATION MANUAL
9
15-01-09 V9
15
General Specifications
Inputs
Balanced via 3 pin XLR type connector.
Outputs
2 pin plug-in screw terminal type connectors for flexible cables
up to 2.5mm²
Protection
VI limiting, DC offset, Thermal and Switch-on Delay
Status Indicators
LED indicators on each channel for Signal, Peak & Protect
Cooling
Force cooled using a two speed DC fan.
Dimensions
482.6mm x 88.0mm (2U) x 325.0mm deep (+ connectors)
Weight
10kg net
16
Technical Specifications
Rated output
120 watts/4 ohm load 85 watts/8 ohm load
Bridged Output
240 watts/8 ohm load
Frequency Response
±1dB 10Hz to 50kHz
THD
<0.005% 1kHz <0.05% 20Hz/20kHz 8 1dB below rated
output
VCA Module THD
<0.03% 20Hz/20kHz
Input Sensitivity
0dBu (775mV)
Input Impedance
10k balanced / 5k unbalanced
Noise
>90dB below rated output
Slew Rate
35V/µS (power amplifier)
Power Input
230V ±5% (115V ±5% available)
Fuse rating
230V - T5A H 115V - T10A H
This product conforms to the following European EMC Standards
:
BS EN 55103-1:1997
BS EN 55103-2:1997
This product has been tested for use in commercial and light industrial environments. If the equipment
is used in controlled EMC environments, the urban outdoors, heavy industrial environments or close to
railways, transmitters, overhead power lines etc. the performance of the unit may be degraded.
The product conforms to the following European electrical safety standard.
BS EN 60065:1998
CX-A6
I
NSTALLATION AND OPERATION MANUAL
10
15-01-09 V9
Safety Considerations and Information
The unit must be earthed. Ensure that the mains power supply provides an effective earth
connection using a three wire termination.
When the mains switch is in the off ‘O’ position the live and neutral conductors of the mains
transformer are disconnected, however some parts of the product will still remain connected to
the live and neutral mains conductors
CAUTION
– Installation
Do not expose the unit to water or moisture
Do not expose the unit to naked flames.
Do not block or restrict any air vent
Do not operate the unit in ambient temperatures above 35
o
C
CAUTION
– Hazardous Live
Do not touch any part or terminal carrying the hazardous live symbol ( )
while power is supplied to the unit as it can result in electric shock.
Terminals to which the hazardous live symbol refers require installation by qualified personnel
CAUTION
- Mains Fuse
Replace the mains fuse only with the same type and rating as marked on the rear panel. The
fuse body size is 20mm x 5mm.
CAUTION – Servicing
The unit contains no user serviceable parts. Refer servicing to qualified service personnel. Do
not perform servicing unless you are qualified to do so.
Disconnect the power cable from the unit before removing the top and do not make any internal
adjustments with the unit switched on.
Only reassemble the unit using bolts/screws identical to the original parts
Bose
is a registered trademark of The Bose Corporation
In the interest of continuing improvements cloud electronics limited reserves the right to alter
specifications without prior notice.
Cloud Electronics Limited 140 Staniforth Road Sheffield S9 3HF England
Telephone +44(0) 114 244 7051 Fax +44(0) 114 242 5462 E-mail: Info@cloud.co.uk