PDF User Manual

WATER

HOPPER

closer to nature

®

 perfect prep

™

 machine

INSTRUCTIONS FOR USE

START / STOP

BUTTON

SETTING

DIAL

WARNING

LIGHTS

ACTION

BUTTONS

DISPENSER

OUTLET

DISPENSER

OUTLET

WATER

TANK

WATER

FILTER

BOTTLE

STAND

WARNING LIGHTS

ACTION BUTTONS

CHANGE

FILTER

CLEANING

MODE

FILTER

VOLUME

RESET

DE-CALC/

DE-SCALE

WATER TANK

HOT

WATER LEVEL

LOW

DE-CALC/

DE-SCALE

CLEANING

MODE

FOR DOMESTIC USE ONLY - NOT INTENDED FOR COMMERCIAL USE
NOTE:  SET UP YOUR UNIT IN A COOL PLACE IN YOUR KITCHEN OUT OF DIRECT SUNLIGHT

Mayborn ANZ Pty Ltd. 
(ABN 66 154 703 134)

Mayborn Group is a business 
name of Mayborn ANZ Pty Ltd. 

 

1. SET UP AND

     CLEANING

2

3

4

Place a container under the 

dispenser outlet to capture the 

water used to clean the system (at 

least 1 litre capacity).

Plug in the unit, the tank empty 

warning light will illuminate.

With the water hopper in place 

(but not the filter) fill the hopper 

with 1 litre of freshly boiled 

HOT

 

WATER

 

- 

Wait for the tank empty warning 

light to go out. The water tank hot 

light will illuminate.

5

6

7

8

Press the cleaning mode button and 

hold for 2 seconds. The cleaning 

mode light will illuminate.

Wait whilst the boiled water is 

emptied from the tank, through the 

dispenser, into the container that you 

placed under the outlet in step 1.

The tank empty warning light will 

illuminate once the water has 

flushed through the system.

Discard the water captured in your 

container and replace it under the 

dispenser.

9a

9b

10

11

12

Remove the water hopper and 

fit the filter*.

Replace in the water tank.

Fill the hopper with 

COLD WATER.

Wait for the tank empty warning 

light to go out. 

Press the start/stop button. A red 

light will flash.

13

14

15

The appliance will dispense an 

amount of hot water.

Press the start/stop button again. 

A green light will flash and an 

amount of water will be dispensed 

to finish the cycle.

Press the filter volume reset button 

for 2 seconds to clear the memory.

Discard dispensed water.

Your system is now ready to use.

Before first use you need to run a cleaning cycle – which should take approximately 10 minutes. You should

clean your unit as part of the set up and again whenever you replace your filter. For hygiene and safety

reasons you should always clean your unit if it has been unused or in storage for longer than 2 weeks.

*Handling the filter cartridge by the top only: 
• Remove the filter cartridge from packaging
• Remove sticker from the top of filter
• Fill a bowl with cold drinking water
• Fully submerge the cartridge in the water
• Gently agitate until the bubbles cease

1

FILTER

VOLUME

RESET

 

2. USAGE

Before each use you must ensure that your water tank is above the minimum fill mark.

Water to fill the unit must come from the cold tap.

Check the water level and top up if 

necessary with 

COLD WATER

. When 

filling the tank, you must always fill the 

hopper and as the water passes through 

the filter you can regularly top it up.

1

Turn the dial to select the feed 

size you require (120ml – 330ml).

2

Position your sterilised bottle 

under the dispenser. Adjust bottle 

stand if necessary. (Bottle neck 

should sit close to the outlet).

3

Press the start/stop button. A red 

light will flash and a volume of 

HOT

 

WATER

 is dispensed into 

your bottle.

4

5

The light will change to solid red 

and there will be a double beep 

to indicate the end of the first 

stage. You will need to make up 

your feed within 2 minutes.

Carefully remove the bottle from 

the stand and measure the 

correct number of formula 

scoops into the bottle.

6

7

Screw the sterilised milk storage 

lid onto the bottle and ensure 

that the lid is tight. Be careful 

when handling hot liquid.

Shake well until the formula 

powder has dissolved.

8

9

Remove the milk storage lid and 

replace your bottle onto the 

bottle stand.

10

11

Always check that the amount 

dispensed is consistent with the 

size of feed you have selected on 

the dial. Add the sterilised teat, 

screw ring and hood and shake.

12

13

For your child’s safety always 

check food temperature before 

feeding by testing on a sensitive 

part of your skin.

Your bottle is now ready to serve. 

Make sure you discard any 

unwanted feed as per the formula 

manufacturers recommendation.

Press the start/stop button again. 

The red light will go out and the 

green light will flash. If this button 

is not pressed within 2 minutes of 

the hot water being dispensed a 

long beep will sound. If the alarm 

sounds you should discard the feed 

and repeat the process from step 1.

Wait whilst the remainder of 

water is dispensed. Once 

completed, there will be a

double beep and the green

light will change to solid.

If at any point you need to stop the perfect prep™ machine you can 
do so by pressing the start/stop button. The pump may continue to 
run for a few seconds and the green light will illuminate to show that 
the process has ended. It will not be possible to restart the machine 
for 20 seconds. Should you have to stop the perfect prep™ machine 
please discard of any feed.

HOW TO STOP THE PERFECT PREP™ MACHINE

For a cool tank keep the unit out of direct sunlight and away from 
sources of heat. Fill with 

COLD WATER

 from the fridge. Regularly top 

up with 

COLD/COOLED WATER

.

HINTS AND TIPS