Clone+ SRF150 User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

U S E R M A N U A L

1.3 Requirements

The following are required to install and use the Clone+™ devices:

digital satellite, cable or terrestrial receivers of Conax, Cryptoworks, Irdeto MediaGuard,

Viaccess-coded pay-tv.

a working

installation*

connected to each of the digital satellite, cable or terrestrial

receivers,

valid subscriber card.

The integral parts of the complete set-up are (for satellite installation):

satellite dish,

full band converter,

coaxial cable for connections.

1.4 Other electronic equipment

Devices which emit radio transmission in their wireless communication may

disrupt the performance of the Clone+™ devices.

1.5 Important notes

Use only the designated power adapter and accessories approved by PYCH International

Electronics Sp. z o.o.. Using any other unsuitable power adapters and accessories which are

not approved by PYCH International Electronics Sp. z o.o. may result in damaging the unit

or severe injury.

a working installation is herewith defined as an installation in which all the devices have been

installed properly.

•

1. Safety and usage information

The Clone+™ devices have been designed according to the safety standards. Before using

this unit, make sure to read the safety and usage information as well as the User Manual.

1.1 Small children and animals

The Clone+™ devices contain small parts which may cause choking or serious injuries if

swallowed. Keep this unit out of the reach of small children or animals.

1.2 Precautions

Keep the Clone+™ device away from rain, moisture and humidity.

Keep the Clone+™ device away from direct sunlight, heat-generating equipment or

strong magnetic field or its emitters or generators.

It is advised not to use the Clone+™ device during the storm. It is recommended

to unplug the device from the mains to eliminate the risk of the electrical shock or

short-circuit.

Do not clean the Clone+™ device with water, liquids or aerosols.

The voltage of the designated power adapter that comes with this unit is 230V AC/50-

60Hz.

Do not overload wall power outlets or extension cords, as this may result in the risk of

fire or electrical shock.

•

2. About Clone+™

2.1 How it works :

The Clone+™ SRF150 Access Server is a main unit which multiplies the privileges of the

subscriber card and sends them to the authorised wireless Clone+™ CRF150 Client Cards.

The Clone+™ CRF150 Client Cards are subordinate units which co-ordinate the

information exchange between the SmartCard reader module in the digital satellite, cable

or terrestrial receiver (or CI module) and the Clone+™ SRF150 Access Server.

2.2 Benefits to the user:

viewing the digital pay-tv simultaneously on 8 TV receivers (independent channels)

with paying only for one subscriber’s plan,

cost saving solution for the user (one subscriber’s plan serves up to 8 TV receivers).

2.3 Key features:

Dedicated for the digital tv platforms using the content encryption systems such as

Conax, CryptoWorks, Irdeto, MediaGuard, Viaccess,

8 active users,

unauthorised access protection,

works with all digital satellite, cable, terrestrial receivers and CI modules which are

Conax, CryptoWorks, Irdeto, MediaGuard, Viaccess compatible,

an extended system of LED indicators,

advanced Plug&Play technology,

•

fast and reliable performance,

software update via USB,

easy and fast installation.

2.4 Product specification:

transmission: RF 868 - 915MHz, BW 150kHz, GFSK, NRZ 38. Kbps,

variable transmitter power from -20 to 5 dBm,

range up to 150 meters (outdoors),

DC 12V-powered.

3. Contents

•

Note:

The

Clone+™

devices only re-send the subscriber card privileges and do not affect the

quality of the sound and vision whatsoever.

Wireless Access Server SRF150

Wireless Client Card CRF150

12V power adapter

User Manual

Mini CD

USB cable

. First steps

4.1 Installation of the SRF150 Access Server and authorisation of the CRF150 Client

Cards.

Step-by-step procedure:

Insert the valid subscriber card of the service provider into the server’s SmartCard slot.

Connect the power tip to the server SRF150 and then plug the power adapter into the

230V AC/50-60Hz mains socket.

Wait until the READY LED is ON (after about 3 seconds).

Remove the subscriber card from the server’s SmartCard slot.

Insert the CRF150 Client Card into the server’s SmartCard slot.

Wait until the UPGRADE LED is OFF on the CRF150 Client Card.

Remove the CRF150 Client Card from the server’s SmartCard slot - the Client Card is

now ready to use with digital receivers or CI modules.

Insert the valid subscriber card of the service provider into the server’s SmartCard slot.

Insert the CRF150 Client Card into the digital receiver or CI module.

Note:

To authorise another CRF150 Client Card, please repeat steps 5 to 7.

Insert the valid subscriber card of the service provider into the server’s

SmartCard slot.

Connect the power tip to the SRF150 server and then plug the power adapter

into the 230V AC/50-60Hz mains socket.

Wait until the READY LED is ON (after about 3 seconds).

Remove the subscriber card from the server’s SmartCard slot.

Insert the CRF150 Client Card into the server’s SmartCard slot.

Wait until the UPGRADE LED is OFF on the CRF150 Client Card.

Remove the CRF150 Client Card from the server’s SmartCard slot.

Insert the valid subscriber card of the service provider into the server’s

SmartCard slot.

Step-by-step procedure:

Authorise the CRF150 Client Cards according to .1, steps 1 to for first

valid subscriber card of the service provider.

Authorise the CRF150 Client Cards according to .1, steps 1 to for another

valid subscriber card of the service provider.

Insert valid subscriber cards of the service providers into the Twin Slot Interface’s

SmartCard slots.

Insert the Twin Slot Interface into the server’s SmartCard slot.

Insert the CRF150 Client Cards into the digital receivers or CI modules.

Insert valid subscriber cards of the service providers into the Twin Slot Interface’s

SmartCard slots.

Insert the Twin Slot Interface into the server’s SmartCard slot.

4.2 Installation of the SRF150 Access Server working with Twin Slot Interface

and authorisation of the CRF150 Client Cards.

Twin Slot Interface enables simultaneous work of subscriber cards of two

different service providers.

Insert the Twin Slot Interface as indicated

Card with

the chip this side

Status

LED

Description

No card in the slot.

0.3 second interval.

Invalid subscriber card or

subscriber card’s malfunction.

The red LED is ON for 2 seconds then it turns

OFF for 0.1 second. The cycle repeats.

Ready to use.

The unit is reading the subscriber

card.

Connection established with the

CRF150 Client Card.

The Link LED is ON when connecting with the

CRF150 Client Card and it goes OFF when the

communication was successful. The Signal

Level LED indicates the full, 3-stage level of

the CRF150 Client Card signal.

The signal level.

The Signal Level LED indicates the full, 3-

stage level of the CRF150 Client Card signal

when connected.

Authorising the CRF150 Client Card.

Software update.

The SRF150 server is connected to a PC via

USB cable.

The LED Indicators messages about the

SRF150 server status

Status

LED

Description

Authorising the

access to the

SRF150 server.

The Upgrade LED blinks for about seconds, stays ON for

0.5 second and goes OFF.

Calibration.

The process takes up to 20 seconds.

Connecting to the

SRF150 server.

The Link LED is ON when the CRF150 Client Card is ready

to connect to the SRF150 server and goes OFF when the

connection was successful.

Connection with

the SRF150 server

within 3 minutes

failed.

The signal level.

The Signal Level LED indicates the full, 3-stage level of the

SRF150 server signal when connected.

System update.

The Signal Level LED indicates the full, 3-stage level of the

SRF150 server signal when connected.

No access to the

SRF150 server.

The LED Indicators messages about the

SRF150 server status

the LED

is ON

the LED is

blinking

the LED

is OFF

5. Software Update

Step-by-step procedure:

Connect the SRF150 server to a PC via the USB cable.

Connect the power tip to the SRF150 server.

Plug the server’s power adapter into the 230V AC/50-60Hz mains socket.

Install the Clone+ Update application from the CD-ROM.

Start the Clone+ Update application and then press „Software Update”.

The software update will take about 3 seconds. The prompts will be displayed.

Unplug the power adapter from the 230V AC/50-60Hz mains socket.

Disconnect the USB cable from the SRF150 server.

Note:

After the software has been successfully updated, please follow the instructions in

4.1 - Installation of the SRF150 Access Server and authorisation of the CRF150 Client

Cards.

Connect the SRF150 server to a PC via the USB cable.

Connect the power tip to the SRF150 server.

Plug the server’s power adapter into the 230V AC/50-60Hz mains socket.

Start the Clone+ Update application and then press „Software Update”.

The software update will take about 3 seconds. The prompts will be displayed.

Install the Clone+ Update application from the CD-ROM.

Button

Clone+ Update v1.0.0.0

To install the Clone+ Update application, double-click on the file

setup.exe

When you are using Microsoft Windows 2000 or Microsoft Windows XP, double-clicking

on the file

setup.exe

may result in displaying a webpage in the Internet Explorer browser.

If this happens, start the installation wizard by double-clicking on the file

Clone+ Update.

manifest.

When you are using Microsoft Windows NT, Microsoft Windows Server 2008, Microsoft

Windows Vista or Microsoft Windows, you have to be logged in as „administrator” to be

able to run

setup.exe

After starting the installation wizard, it will advise the user to download and install the

latest version of the application. Next, the installation wizard will inform the user about

the installation of the drivers. Follow the instructions of the installation wizard. After the

installation has been successful, the Clone+ Update will run. To run the Clone+ Update

application again, go to:

Menu Start => Programs => PYCH International Electronics => Clone+ Update

Note:

If the installation wizard detects that the .NET Framework 2.0 component is not

installed, the wizard will automatically download and install the missing component.

Disconnect the USB cable from the SRF150 server.

Unplug the power adapter from the 230V AC/50-60Hz mains socket.

6. Restoring the factory settings

Step-by-step procedure:

Connect the power tip to the server.

Plug the server’s power adapter into the 230V AC/50-60Hz mains socket.

Wait until all the LED indicators are ON (after about 15 minutes).

Note:

After restoring the factory settings of the unit, please follow the instructions in

4.1 - Installation of the SRF150 Access Server and authorisation of the CRF150 Client

Cards.

. Usage and maintenance

Correct disposal of this product:

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be

disposed with other household wastes at the end of its working life. To prevent possible

harm to the environment or human health from uncontrolled waste disposal, please

separate this from other types of wastes and recycle it responsibly to promote the

sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product,

or their local government office, for details of where and how they can take this item for

environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the

purchase contract. This product should not be mixed with other commercial wastes for

disposal.

Manufacturer

conforms to the following product specifications:

Safety: EN 60950,

EMC: EN 30189,

Radio: EN 300220.

We herewith declare that the above mentioned product

complies with the requirements of the following directives:

R&TTE 99/05/EC,

3/023/ECC,

89/336/ECC.

•

D E C L A R AT I O N O F C O N F O R M I T Y R & T T E

Grzegorz Pych

President of the Board

Warszawa

1.09.2009

www.cardsplitter.nu

Clone+™ Home Edition 150: SRF150

Wireless SmartCard Splitter of Digital PayTV Subscription

erewith declare that:

Clone+

www.cardsplitter.nu

Ask a Question ?