ClimateMaster ATA11U03 Installation Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

ATA11U03

Non-Programmable

Heat Pump Thermostat

Installation Manual

97B0082N06

Revised: 16 September, 2013

FOR INSTALLER

AND OWNER ONLY

Table of Contents

Safety Considerations

General 3
Package Contents

Installation Considerations

Power 3
Wiring 3
Thermostat Location

Installation 4
Configuration

5-8

Entering and Exiting Configuration Mode

Configuration Options

Exiting Configuration Mode

System Start-Up and Checkout

Installer Test Mode

Terminating Installer Test

Checklist

Operation

Mode Selection

Fan Selection

Fan Display

Set Temperature Selection

Display Lighting

Remote Sensor Temperature Display

Timers 10
Five-Minute Compressor Timeguard

Minimum On Timer

Cycle Timer

Troubleshooting

Space Temperature Sensor Failure

Memory Failure

Equipment Outputs

Wiring Diagrams

Thermostat Configuration Record

Revision History

W A T E R - S O U R C E H E A T P U M P S

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

This Page Intentionally Left Blank

T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

General

Safety Considerations

Read and follow manufacturer instructions carefully.
Follow all local electrical codes during installation. All
wiring must conform to local and national electrical
codes. Improper wiring or installation may damage
thermostat.

Recognize safety information. This is the safety alert
symbol . When the safety alert symbol is present on
equipment or in the instruction manual, be alert to the
potential for personal injury.

Understand the signal words

DANGER, WARNING,

and

CAUTION

. These words are used with the safety

alert symbol.

DANGER

identifies the most serious

hazards which will result in severe personal injury or
death.

WARNING

signifies a hazard which could result

in personal injury or death.

CAUTION

is used to identify

unsafe practices which would result in minor personal
injury or property damage.

General

Non-programmable heat pump thermostats are wall-
mounted, low-voltage thermostats that maintain
room temperature by con trolling the operation of
heat pump systems. A variety of features are provided
including sepa rate heating and cooling set points, auto
changeover, keypad lockout, back lighting, and built-in
installer test.

Figure 1: Non-Programmable Heat Pump Thermostat

This Installation Instruction covers installation,
configuration, and start up of the non-programmable heat
pump thermostat.

This manual is intended for installer and owner only.

Package Contents

1 - Thermostat
1 - Backplate (mounting base with terminal strips)
2 - Screws and anchors
3 - User Operating Manual (review with end user)

Installation Considerations
Power

- 24 volt AC (50/60 Hz) power via the Rc/Rh and C

terminals. Rc and Rh terminals are connected via factory-
installed jumper wire.

Wiring

Requires 6 conductor thermostat cable for 2 fan

speed units. The wire length should be no more than 250
ft (76 m). Use 22 AWG (American Wire Gage) for normal
wiring applications. Continuous wire lengths over 100 ft
(30.5 m) should use 20 AWG or larger.
Reconfigure if unit is only 1 fan speed, see option 40.

Note: This thermostat has battery compartment but is

non-operational and must be wired.

Thermostat Location

—

The thermostat should be mounted:
• approximately 5 ft (1.5 m) from the floor
• in the conditioned space, preferably on an inside wall

on a section of wall without pipes or ductwork

The thermostat should NOT be mounted:
• close to a window, on an outside wall, or next to a

door leading to the outside

• where exposed to direct light and heat or any other

temperature-radi ating object which may cause a false
reading

• close to or in direct airflow from supply registers or

return air grille in areas with poor air circulation.

W A T E R - S O U R C E H E A T P U M P S

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

Installation -

To install the thermostat, perform the

following procedure:
1. Turn off all power to equipment.

Installation

�

CAUTION!

�

ENVIRONMENTAL HAZARD!

Failure to follow this

caution may result in environmental damage. Mercury is a

hazardous waste. Federal regulations require that mercury

be disposed of properly.

2. If an existing thermostat is being replaced:

a.  Remove existing thermostat from wall.
b.  Record the wire color and old termi nal marking.
c.  Disconnect wires from existing thermostat, one

at a time. Be careful not to allow wires to fall back
into the wall.

d. Recycle old thermostats that contain Mercury.

Figure 2: Backplate Mounting

2.A

New Installation -

a. Optional - install 2x4 box horizontal.

b. Run new wiring, must meet all NEC and local

codes.

c. Note each wire color and connection at unit.

3. Press the thumb release at the top of the thermostat

and pull apart carefully to separate back-plate from

the thermostat.

4. Pull thermostat wires through large hole in

backplate. Level back-plate against wall (for
appearance only, the thermostat does not need be
leveled for proper operation) and mark wall through
two mounting holes. See Fig. 2.

5. For direct mounting to wall, drill two 3/16-in.

mounting holes in the wall where marked, use
anchors provided.

6. Secure backplate to box or wall with two screws

provided. Make sure all wires extend through hole in
backplate.

7. Adjust length and routing of each wire to reach

proper connector block and terminal on backplate
with 1/4-in. (6 mm) of extra wire. Strip only 1/4-in. of

insulation from each wire to prevent adjacent wires
from shorting together when connected.

8. Match and connect equipment wires to proper

terminals of the connector blocks (see Fig. 3).

9. Push any excess wire into wall and against backplate.

Seal hole in wall to prevent air leaks. Leaks can affect
operation.

10. Attach thermostat to backplate by inserting tab on

bottom edge and hinging up until top snap secures.

11. Turn ON power to unit.

When power is applied, all display icons are lit for 2
seconds to test the display. Following this, the equipment
type for which the thermostat is configured is displayed
for an additional 2 seconds.

�

CAUTION!

�

Failure to follow this caution may result in equipment

damage or improper operation. Improper wiring or

installation may damage the thermostat. Check to make

sure wiring is correct before proceeding with installation or

turning on unit.

Figure 3: Terminal Strip (wiring diagram - see figure 7)

�

WARNING!

�

WARNING!

Electrical shock can cause personal injury and

death. Before installing thermostat, shut off all power to

this equipment during installation. There may be more than

one power disconnect. Tag all disconnect loca tions to alert

others not to restore power until work is completed.

T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

Configuration

Configuration options enable the installer to configure
the thermostat for a particular installation. These
configuration options are stored to the internal
memory so they are retained through a power outage.
The availability of some configuration options will be
dependent upon other conditions in the thermostat.

Table 1: Configuration Options Summary

Entering and Exiting Configuration Mode

- Press and

hold the fan button for about 10 seconds. After the 10
second period the Option number “02” will appear
flashing in the space temperature location. The value of
the configuration setting will be displayed in the set point
location.

The parameter that is changeable will be determined by
the flashing area. The up or down buttons can be used

to select a new value. The mode button can be used to
toggle/move the selection between the configuration
option number and the configuration value. To exit the
installer configuration screen, press the fan button. If
no button is pressed for three minutes, the installer
configuration screen will time out and the thermostat will
return to normal operation.

All changes to the installer configuration are saved as
they are made. There is no provision to exit the installer
configuration and cancel the change. The installer will
have to manually change a configuration back to its
original value to “undo” a change.

Configuration Options

OPTION 02 — REMOTE SENSOR SELECTION

— A

remote sensor 17B0008N05 (for inside duet), or ASW06
(for wall) can be connected to the S1 and S2 screw
terminals to sense either remote space, return air,
outdoor air, or supply air temperature.

Selection: rA, Od, SA, rS
rA* — Sense return air temperature

* Display only, not used for temperature control.

Od*— Sense outdoor air temperature
SA*— Sense supply air temperature
rS — Sense remote space temperature
Default: rS

Note: Option 02 cannot be changed from the rS setting

if Option 05 is set to either r or Lr.

OPTION 03 — ENGLISH/METRIC

— This configuration

selects be-tween Fahrenheit (F) and Celsius (C) operation.

Selection: F, C
Default: F

OPTION 05 — SPACE TEMPERATURE SENSING

—

This selection determines which sensor the control
will use for measuring space temperature. Space
temperature can be sensed in one of three ways: the
local sensor (L) located on the thermostat, the remote
sensor (r), or the average of local and remote sensors (Lr).

Selection: L, r, Lr (Do not use)
L — Local sensor: The onboard thermistor is the
control point for the temperature control algorithm.
r — Remote space sensor: The remote space
temperature is the control point for the temperature
control algorithm.

NOTE: This selection is only available if Option 02

indicates that the S1, S2 terminals are sensing a

remote space temperature.

Default: r

�

WARNING!

�

WARNING!

User should not reconfigure installer set up.

Equipment damage could occur.

�

NOTICE

�

Wall thermostat requires configurating for on board sensing.

Installer must configure 05 to L unless remote sensor

is used.

Option

Number

Configuration

Default

Remote Sensor Selection

English/Metric

Space Temperature Sensing

Equipment DDC Controller

Deadband between Heating and Cooling Set Points

Space Temperature Display Adjustment (Offset)

Auto Mode Availability

Maximum Cycles Per Hour

Backlight Configuration

Outdoor Air Temperature Adjustment (Offset)

Keypad Lockout

Minimum Cooling Set Point

Maximum Heating Set Point

Temperature Display

Fan Speeds Selection

W A T E R - S O U R C E H E A T P U M P S

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

OPTION 07 — EQUIPMENT DDC CONTROLLER

—

This selection should be set to ON when control is to be
used with ClimateMaster heat pump units, the DXM or
CXM will take care of the timeguard and cycle timers. The
minimum on time is still controlled by the thermostat. Off
setting could delay compressor start by 12 minutes.

Selection: OF(F), ON
OF — Timeguard and cycle timers are enabled
ON — Timeguard and cycle timers are disabled
Default: OF (off)

OPTION 11 — DEADBAND BETWEEN HEATING

AND COOLING SET POINTS

— This selection allows

the installer to choose how much differential will exist
between the heating and cooling set points.

Selection: 1 to 10 (F or C)
Default: 5

OPTION 13 — SPACE TEMPERATURE DISPLAY

ADJUSTMENT (OFFSET)

— This configuration is

the number of degrees to be added to the displayed
temperature to calibrate or deliberately miscalibrate
the measured space temperature. This selection is not
available to the installer if Option 39 is set to SP (set
point display).

Selection: –5 to 5 F (always in F) Default: 0

OPTION 15 — AUTO MODE AVAILABILITY

— The

ON selection will allow automatic changeover between
heating and cooling as demand requires a mode
selection. OF maintains either heating or cooling mode
selection only.

Selection: ON, OF(F)
ON — Auto mode
OF — Manual mode
Default: ON

OPTION 16 — MAX CYCLES PER HOUR

— The

maximum cycle rate is limited by internal timers to the
selected number of cycles per hour. Selection of a higher
number causes faster cycling resulting in more constant
room temperature.

Selection: 4, 6, 8
4 — The Y1 output will be energized at most twice
per hour. When an output is energized, it will not be
energized again for 15 minutes.
6 — The Y1 output will be energized at most four
times per hour. When an output is energized, it will
not be energized again for 10 minutes.
8 — The Y1 output will be energized at most six times
per hour. When an output is energized, it will not be

energized again for 8 minutes.
Default: 4

OPTION 18 — BACKLIGHT CONFIGURATION

—

When set to OF (off), the backlight will be lit for 10
seconds after a button is pressed. After 10 seconds of no
button presses, the backlight turns off.

When ON is enabled, the backlight will normally be
on and dim in appearance. The backlight brightness
becomes brighter when a button is pressed. After 10
seconds of no button presses, the backlight will return to
the dimmer level until another button press occurs.

Selection: OF(F), ON
Default: ON with 24 vac power; for batteries only,
default is OFF.

OPTION 20 — OUTDOOR AIR TEMPERATURE

DISPLAY ADJUSTMENT (OFFSET)

— This selection

is not available unless Option 02 is set to Od (outdoor
air temperature) and a valid sensor is connected to S1
and S2 terminals. It allows the calibration, or deliberate
mis-calibration of the outdoor air temperature sensor
reading.

Selection: –5 to 5 (number of degrees F added to the
outdoor air temperature reading to “calibrate” the
temperature sensor)
Default: 0

OPTION 21 — KEYPAD LOCKOUT WITH PASSCODE

— The thermostat is shipped with the keypad fully
accessible. This option allows the installer to limit access
to the keypad.

Selection: OF(F), 1, cd
OF — When set to OF, the user has full access to the
keypad
1 — The user will only have access to modify the set
points (within the set point limits of Option 26 and
Option 27). The padlock icon will be displayed until
the user presses and holds the up and down buttons
simultaneously for five seconds to unlock the keypad.
Once the keypad is unlocked, the user has full access
to the thermostat functionality. The keypad returns
to the locked condition after no buttons have been
pressed for two minutes.
cd — The entire keypad is locked and the padlock
icon is displayed. When the user presses a button
the backlight turns on to maximum brightness for 10
seconds and a “--” is displayed in the temperature
setting. The user must enter the unlock code and
press the mode button to unlock the thermostat.
The padlock icon will then turn off and the user will

Configuration

T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

have full access to the thermostat functionality. The
thermostat will lock after no buttons have been
pressed for two minutes.

If the option value is set to “cd”, the mode, up and
down buttons will work as follows:
1. Pressing the mode button once will display the

flashing Option number (21).

2. Pressing the mode button again and the option

value will flash OF, 1 or cd.

3. Pressing the mode button a third time will display

the keypad lock icon and the code entry values
(see Fig. 4). The up and down buttons will allow
the selection of a code value between 00 to 199.

4. Pressing the mode key again will return the focus

to the Option number (21) .

Default: OF (off)

OPTION 26 — MINIMUM COOLING SET POINT

— This parameter establishes the minimum cooling
set point that the user is allowed to set. Otherwise,
the equipment type allows both heating and cooling
operation, so the minimum is 60 F plus Option 11
(deadband) and the maximum is 90 F.

Selection: minimum = 60 F + deadband, maximum
= 90 F
Default: 60 F (based on the adjustable deadband
default = 5)

OPTION 27 — MAXIMUM HEATING SET POINT

—

This parameter establishes the maximum heating set
point that the user is allowed to set. The equipment

type allows both heating and cooling operations, so the
minimum is 50 F plus Option 11 (deadband) and the
maximum is 90 F.

Selection: minimum = 50 F, maximum = 90 F –
deadband
Default: 85 F (based on adjustable deadband default = 5)

OPTION 39 — TEMPERATURE DISPLAY

— This

configuration allows the installer to select either the
set point temperature or the space temperature to be
displayed on the large temperature display digits.

When the option St is chosen, the space temperature, as
defined by Option 05, is displayed using the traditional
space temperature digits on the LCD display. The current
set temperature is displayed using the normal set-point
display digits.

When SP is chosen, the current set point temperature is
displayed using the traditional space temperature digits
on the LCD display. The normal set point display digits
remain blank. Space temperature is not be displayed, but
if a problem occurs with the actual space temperature
sensor, the characters “- -” will be displayed instead of
the set temperature to indicate that the temperature
sensor has an error.

NOTE: The “Actual Temp” icon is not to be

displayed when the sensor type is set to Set Point

display (SP).

Selection: St, SP
Default: St (Space Temperature)

OPTION 40 — FAN SPEEDS

— This configuration

allows the installer to select the number of fan speeds
the system with operate with. When set to 1, the single
speed fan only will be available (LO). When set to 2, both
fan speeds will be available (LO & HI).

Selection: 1, 2
Default: 2
Check unit submittal for fan speeds available. Set
accordingly.

OPTION 99 — RESET TO FACTORY DEFAULTS

— This

configuration allows the installer to return the thermostat
to its “out of the box” settings. Not recommended
to use.

IMPORTANT:

All configuration settings, mode, fan and

set point settings which have been manually entered will
be lost and will require resetting.

When this setting is first selected, 99 will be displayed in
the space temperature location and an initial value of 10

Configuration

Figure 4: Selection of Code Value

W A T E R - S O U R C E H E A T P U M P S

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

will be displayed in the set-point location.
To initiate factory defaults, the installer then presses the
mode button until the 10 is flashing. The installer then
presses and holds the down button. While the down
button is held, the 10 will count down from 10 to zero at
a rate of 2 counts per second (5 seconds total). When the
value reaches zero, all display segments are turned on for
five seconds and the factory defaults are restored. If at
any time during the countdown the installer releases the
down button, the countdown terminates and the display
returns to the starting value of 10.

Exiting Configuration Mode

- To exit the configuration

mode, press the fan button.

SYSTEM START-UP AND CHECKOUT
Installer Test Mode

— This thermostat has a built-

in installer test capability. It allows easy operation of
equipment without delays or set point adjustments to
force heating or cooling. To enter installer test mode,
press and hold the fan button for 15 seconds (after 10
seconds installer configuration is entered; a continuous
15 seconds and installer test is entered). At the start of
installer test, the mode is Off, the fan is “fan auto” and
the set point display displays “InS.”

NOTE: Unit must be powered up and CXM/DXM

in test mode to disable unit timers or compressor

not energized for more than 5 minutes.

The mode button is used to change the system operating
mode to test the heating and cooling equipment. Auto
mode is not available during installer test.

When the mode is set to heat, “H” is displayed, heating
is energized for 180 seconds. During the installer test
operation, the “on” icon is displayed.

At the end of the equipment test cycle the mode returns to
OFF.

The LCD display counts down the time remaining
(in seconds, from 180 to 0) for each stage when the
equipment is energized. See Fig. 5.

The same procedure is repeated for the cool mode. “C”
is displayed when cooling is active.

The test of a heating or cooling cycle can be terminated
before the timer counts down to zero by pressing the
mode button.

Pressing the fan button alternates the fan selection
between fan auto and fan on and the fan output follows
accordingly. There is no timer associated with the installer
testing of the fan operation.

Terminating Installer Test

— After 15 minutes of no

button presses by the installer, installer test is terminated.

Pressing the up button, down button, or cycling
thermostat power at any time during installer test
terminates the installer test and returns the thermostat to
normal operation.

Figure 5: Installer Test Mode

Checklist

— The following installer checklist should be

performed after completing installation:
1. Run equipment through several heating and cooling

cycles to ensure proper operation. To operate the
thermostat in its normal operating mode, consult the
User Operating Manual.

2. If the equipment is to be left in operation, the

set points and operating mode must be properly
selected.

3. Put away tools and instruments and clean up debris.
4. Review and leave this manual and User Operating

Manual with owner.

T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

OPERATION

Mode Selection

— The mode button allows the user to

display the off, heat, cool, auto icons. Pressing the mode
button cycles through the available modes based on the
equipment selection from Option 15. Available choices
are listed in Table 2.

Table 2: Mode Selection

Fan Selection

— The thermostat offers two continuous

(ON) or two cycling (AUTO) and two fan speeds high (HI)
or low (LO). Pressing the fan button cycles through the
following displays fan on LO, fan on HI, auto fan LO, auto
fan HI.

Fan Display

— If Option 39 is set to display set point

(SP), then the two-speed fan setting remains on the
display. If the current fan speed is not shown on the
display, the first press of the fan button will display the
current selection. The fan selection can only be changed
by a fan button press when the current selection is shown
on the display. See Fig. 6.

If Option 39 is set to display the space temperature (St),
then the two-speed fan setting (LO or HI) remains on the
display for three seconds after the last press of the fan
button.

Figure 6: Current Fan Selection Display

Set Temperature Selection

— If auto mode is not

active and off mode is not active, pressing the up or
down button causes the set point corresponding to the
current system mode to be updated. If the up or down
button is held, the set point value will be scrolled. The
set point change also takes into account that Option 11
(deadband) is preserved along with ensuring that Option
26 (minimum cooling set point) and Option 27 (maximum
heating set point) are taken into account to enforce set
point limits.

If auto mode is active, pressing the up or down button
causes the set point corresponding to the current
operating mode to be updated. To move between the
heat and cool set points, press the mode button to
toggle between set points. Once the desired set point
has been adjusted, press the mode button to return to
auto mode.

If off mode is active, the up and down buttons are
ignored for changing set point(s).

When changing the set points, the following restrictions
are in place. The cool set point cannot be increased
above 90 degrees F (32 C) or decreased below Option
26, the minimum cooling set point. The heat set point
cannot be decreased below 50 F (10 C) or increased
above Option 27, the maximum heating set point.

When Option 39 is set to SP (set point), the set point
adjustment is displayed in the large space temperature
digits.

Display Lighting

— The display has two levels of

lighting, high level and low level. High level lighting
comes on for 10 seconds when buttons are being
pressed. The low level can be selected (see Option 18)
for continuous backlight.

Remote Sensor Temperature Display

— Pressing

the up and down buttons simultaneously displays the
temperature of the sensor connected to the S1 and S2
terminals for five seconds, then the thermostat returns to
normal operation.

If the sensor is invalid, then the display shows “--” in the
large temperature display digits.

OPTION 15

AVAILABLE MODES

Off, Heat Cool, Auto

Off

Off, Heat, Cool

W A T E R - S O U R C E H E A T P U M P S

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

Timers

— There are several timers which influence the

thermostat’s operation that are listed below. If any of the
timers is preventing the equipment from turning on, the
“on” icon will flash.

Five-Minute Compressor Timeguard

— This timer

prevents the Y1 output from turning on unless it has been
off for 5 minutes. (Option 07 set to OF)

After a power cycle, a randomized delay will be added
to end of the timeguard timer to prevent multiple units
from hitting the power grid all at the same time. The
randomization timer will be between zero and five
minutes. If a demand exists, compressor outputs will
energize between 5 and 10 minutes after the power
cycle. It can be defeated by simultaneously pressing the
fan and up keys.

Minimum On Timer

— Once the equipment has been

turned on, it must remain on for 3 minutes. A change in
mode or set point will cancel this timer.

Cycle Timer

— The number of equipment cycles per hour

is determined by configuration Option 16. Based on the
selection of 4, 6 or 8 cycles per hour, this timer is set to
15, 10 or 8 minutes. This much time must elapse from the
start of one cycle before another cycle can start, imposing
the cycles per hour limits. It can be defeated for one cycle
by simultaneously pressing the fan and up keys.

TROUBLESHOOTING

There are three system error messages that may appear
on the thermostat screen indicating a problem with
the thermostat’s operation. See text below for possible
system error messages and their meaning.

Space Temperature Sensor Failure

— If the room

temperature sensor fails, the temperature display will
show “--” (two dashes). If the space temperature is
the average of both the local and remote sensors (as
configured in Option 5), and one of the sensors fails, the
thermostat provides control to the valid sensor only. The
display will alternate every 10 seconds between “--” for
the invalid sensor and the reading from the valid sensor.

Memory Failure

— If there is an internal memory failure,

the temperature display will show “E4,” the thermostat
needs to be replaced.

WIRING DIAGRAMS

System wiring diagram is shown for typical ClimateMaster
heat pump unit. See Fig. 7.

O is Energized for cooling
G is low speed fan
G2 is hi speed fan

Figure 7: Typical Wiring Diagram - Heat Pump

W OR W1
C
G
H (DXM ONLY)

O
Y or Y1

NOTE 1

NOTE 2

S2
S1

THERMOSTAT

HEAT PUMP

CXM/DXM

HEAT PUMP

REMOTE

SENSOR

(Optional)

T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

THERMOSTAT CONFIGURATION RECORD

INSTALLER:

PART NUMBER:

DATE:

HOLE IN WALL SEALED:

MODE SETTINGS:

MODE (Off, Heat, Cool, Auto):

HEATING SET POINT:

COOLING SET POINT:

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring

obligations.

Thermostat Configuration Record

CONFIGURATION DESCRIPTION

USER OPTIONS

SETTING

Option 02

_____ Remote Sensor Selection

Option 03

_____ English/Metric

Option 05

_____ Space Temperature Sensing

Option 07

_____ Equipment DDC Controller

_____ Deadband between Heating and Cooling Set

Option 11

Points

_____ Space Temperature Display Adjustment

Option 13

(Offset)

Option 15

_____ Auto Mode Availability

Option 16

_____ Maximum Cycles Per Hour

Option 18

_____ Backlight Configuration

_____ Outdoor Air Temperature Display Adjustment

Option 20

(Offset)

Option 21

_____ Keypad Lockout

Option 26

_____ Minimum Cooling Set Point

Option 27

_____ Maximum Heating Set Point

Option 39

_____ Temperature Display

Option 40

_____ Fan Speeds Available (1 or 2)

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring

obligations.

W A T E R - S O U R C E H E A T P U M P S

ATA11U03

R e v. : 0 9 / 1 6 / 1 3

Revision History

Date:

Item:

Action:

09/16/13

Warning and Table, page 5

Updated

08/27/13

First Published

We work continually to improve our products. As a result, the design and specifications of each product at the time of order may be changed without

notice and may not be as described herein. Please contact our Customer Service Department at 1-405-745-6000 for specific information on the

current design and specifications. Statements and other information contained herein are not express warranties and do not form the basis of any

bargain between the parties, but are merely our opinion or commendation of its products.
We are a proud supporter of the Geothermal Exchange Organization - GEO. For more information visit geoexchange.org

Rev.: 16 September, 2013

*97B0082N06*

97B0082N06

Ask a Question ?