PDF User Manual

CLIMATE KING 

User

’

s Manual and

 

Operating

 

Instructions

PREMIUM

  

QUALITY

 

FAN HEATERS

 

READ INSTRUCTIONS CAREFULLY: 

Read and follow all instructions.

Place instructions in a safe place for future reference. Do not allow anyone
who has not read these instructions to assemble, turn on, adjust or operate
the heater.

IMPORTANT
DO NOT EXPECT THESE HEATERS TO PRODUCE SUPERHOT AIR

This unit is designed to raise the ambient temperature of an entire room, the
temperature of the air coming out of the front of the heater will be warmer than the
general temperature of the room, but there may not be a significant increase due
to

 the large volume of air passing over the element. The unit achieves 

a hot room by passing large amounts of air over the elements several times.

 For the same reason, the element is hot during operation, but does not glow visibly.
 The room temperature depends on room size, insulation and the ambient temperature,
 which will increase as the room gets warmer.

SERVICE WARRANTY

Cottage Stores LLP guarantees the product free from defects in materials
and workmanship for a period of twelve months after purchase. Proof of purchase
will be required.
Should this unit be operated under conditions other than those
recommended, at voltages other than the voltage indicated on the unit, or
any attempts made to service or modify the unit, then the warranty will be

rendered void.
The product you buy may sometimes differ slightly from illustrations. This
warranty is in addition to, and does not affect, your statutory rights. If you
have any problems with this product, please 

in the first instance call the

retailer from whom you purchased it.

Climate King
Cottage Stores LLP
7 Harris Drive
Rugby CV22 6DX
United Kingdom

Keep box and packaging until the end of the warranty period

Model:

HCK­BX5

;

HCK­BX9

;

HCK­BX15

;

HCK­BX22

Instruction Manual

OWNER and OPERATORS  RESPONSIBILITY

It is the responsibility of the owner and the operator to read, understand and
comply with the following:
You must check all electrical products, before use, to ensure that they are safe.
You must inspect power cables, plugs, sockets and any other connectors for wear
or damage. You must ensure that the risk of electric shock is minimised by the
installation of appropriate safety devices. A Residual Current Circuit Breaker
(RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current Device (RCD) is used. It is particularly
important to use an RCD with portable products that are plugged into a supply
which is not protected by an RCCB. If in any doubt consult a qualified electrician.
You must also read and understand the following instructions concerning
electrical safety.
 The Electricity at Work Act 1989 requires that all portable electrical
appliances, if used on business premises, are tested by a qualified electrician,
using a Portable Appliance Tester (PAT), at least once a year.
. The Health & Safety at Work Act 1974 makes owners of electrical
appliances responsible for the safe condition of those appliances and the safety
of the appliance operators. If in any doubt about electrical safety, contact a
qualified electrician.
 Ensure that the insulation on all cables and on the appliance is safe before
connecting it to the power supply. See 5.1.1. and 51.2. and use a Portable
Appliance Tester.
. Ensure that cables are always protected against short circuit and overload.
. Regularly inspect power supply cables and plugs for wear or damage and
check all connections to ensure that none are loose.
. Important: Ensure that the voltage marked on the appliance matches the
power supply
to be used and that the plug is fitted with the correct fuse .
 

DO NOT 

pull or carry the appliance by the power cable.

 

DO NOT 

pull the plug from the socket by the cable.

 

DO NOT 

use worn or damaged cables, plugs or connectors. Immediately

have any faulty item repaired or replaced by a qualified electrician.

Model:

HCK­BX5

;

HCK­BX9

;

HCK­BX15

;

HCK­BX22

Instruction Manual

1. Introduction

1.1

This heater is an electric heater with ventilator/fan motor

.It is suitable for

household, warehouse, work-shop or

greenhouse. It

 

includes

a thermostat and a non-self-reset thermostat. The thermostat

 senses

the air inlet temperature

and controls the room temperature. Non-self-reset thermostat will switch off the heater

to 

 

avoid

overheating to ensure

safety

 

 

.

1.2

When using the heater for the first time, you may notice a slight emission of smoke. This is quite normal and it stops

after a short time. The heating element is made of stainless steel and was coated with protection oil

 in

production. The

smoke is caused by the

 residue

when heated.

2. Technical specifications

Model

HCK­BX5

HCK­BX9

HCK­BX15

HCK­BX22

Waterproof Class

IP24

IP24

IP24

IP24

VOTAGE

400V

400V

400V

400V

required power

5000W

9000W

15000W

22000W

current

7.2A

13.0A

21.67A

31.8A

Required Fuse

16A

16A

32A

63A

Setting

30/2500/5000W

52/4500/9000W

90/5000/10000/1500

0W

110/11000/22000W

Size of heater ( mm)

270x255x400

300x355x490

410x360x550

450X410X600

N.W.

6.5kgs

9.6kgs

14.5KGS

21.8KGS

2.1

Housing of steel plate and coated by heat-resistant powder .

2.2

Electrical connection

models

 

 

 

 

 

leads.

 

cable

 

separate

 

with

 

supplied

 

are

 

HCK-BX22

 

and

 

BX15

 

HCK-

 

Models

 

 

cables

 

in

 

built

 

have

 

HCK-BX9

 

and

 

HCK-BX5

 

:

.

Detail please see 5 point

3. Description of Control Panel

HCK­BX5

HCK­BX9

HCK­BX15

HCK­BX22

3.1 Left Knob:

Selector

3.2 Right Knob:

Thermostat dial

4. Special safety regulations

4.1

Warning: In order to avoid overheating , please DO NOT COVER heater during using .

4.2

When using electrical appliance basic precautions should always be followed including below :

4.2.1

The fan heater is not suitable for use outdoors in damp weather, in bathrooms or in other wet or damp environments.

4.2.2

Please note that the fan heater can become very hot and should, therefore, be placed at a safe distance from

flammable objects such as furniture, curtains and similar.

4.2.3

Do not cover the fa

heater

n

 

 

or

 

use it where industrial powders or dust can contaminate the 

atmosphere

 

.

4.2.4

Do not place the fan heater immediately under a wall socket.

4.2.5

Do not connect the fan heater using an on/off timer or other equipment which can automatically switch the device on.

4.2.6

The fan heater must not be placed in rooms where flammable liquids or gases are used or stored.

4.2.7

If an extension cord is used, it must be as short as possible and always be fully extended.

4.2.8

You must not connect other appliances to the same mains socket as the fan heater.

4.2.9

Heater can’t be used in bath-room, shower stall and Pool directly.

4.2.10

If the cord of heater was damaged ,it must be repaired by manufacturer or maintenance point

4.2.11

Make sure heater is always under surveillance and keep children and animals away from it;

4.2.12

Do not place the appliance on moving vehicles or some where easy to be tipped over .

4.2.13

When you don’t use the appliance for a long time, unplug the appliance .Don’t leave the heater for a considerable

amount of time when in use. Pull the plug straight out ,never remove the plug by pulling on the cord .

4.2.14

Keep the heater far from curtain or places where the air inlet can easily be blocked.

4.2.15

The power coupler is waterproof when not in use. In order to prevent possible electric shock or leakage

CLIMATE KING PREMIUM 

3­PHASE 

BOX HEATER

S

 

 

current ,never use the appliance with wet hand or operate the appliance when there is water on the power cord.

4.2.16

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact you

local government for information regarding the collection systems available. If electrical appliance are disposed of in

landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health

and well-being.

4.2.17

This appliance is not intended for use by person (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.

5. Instruction

if

extension

 

an

 

using

 

 

 

s

coupler

)

 

)

 

only

 

HCK-BX22

 

and

 

HCK-BX15

 

(

Figure 1

1. Five pins connector 380V/415V 50Hz

2. Power cord

3. Five pins plug 380V/415V 50Hz IPX4
5.1

Th

Users

 

 

supplied

 

the

use 

 

 

 

should

 

models

 

HCK-BX22

 

and

 

HCK-BX15

 

the

 

of

 

 

 

plug.

 

and

 

cable

 

in

 

 

built

 

the

 

using

 

socket

 

power

 

a

 

into

 

straight

 

plugged

 

be

 

can

 

HCK-BX9

 

and

 

HCK-BX5

 

 

e

power coupler as sho

 

w in the figur

.

e

Any

used

 

coupler

 

.

should match with the appliance and earthing pro

tocol

. The coupler should be VDE approved

 

.

 

For

the specificat

ion

for each model please see below :

 

 

 

Model

Type of Power cord

Plug Curren

 

t

HCK­BX15

 
 

H07RN-F 4G2.5mm2

 

 

32A

HCK­BX22

H07RN-F 4G4.0mm2

63A

5.2

When you connect the power connector with the appliance , open the lid

 in the direction of the arrowhead

Figure2

5.3 Before you

 turn

on the appliance make sure that the selector switch and the thermostat are switch

ed

OFF,

so

that when you connect the plug with power supply , there will be no spark

s

induced between the plug and the socket outlet

. 

This

can extend the work life of the plug

.

Then connect the plug to the power

 to 

operate the appliance . During the operation

if spark

s

detected at

 the 

connection, shut off the appliance and connect again.

5.4

After use

, first 

shut down the appliance ,

then 

pull out the plug , then

 remove

the position pin and remov

any

e

coupler.

are

 

 

6. Using Instructions

6.

Inspect

1

6.2

Position the fan heater so that it stands upright on a firm surface and at a safe distance from wet environments and

flammable objects.

6.3

Connect the fan heater to the mains.

6.4

Set the thermostat knob to the MAX and let the heater operate with full power .

6.5

The fan heater will switch on when the heating selector is set to one of the

power settings.

6.6

Once the room reaches the required temperature,

the 

heating element will stop but

 the 

fan

will continue

.Once the

temperature decrease

s

, the heating element will be

re­commence

working

 automatically

.

6.7

The fan heater now starts and stops automatically and thus keeps the room temperature constant.

6.8

Before

 turning 

off , please turn the thermostat to OFF position and turn the Selector to Fan or off , let the appliance

cool down for two minutes .

6.9

Time-delay thermostat cut-off

:­

if you forgot to turn the thermostat to OFF position before

 turning off

heater ,

Thermostat cut-off

 

and Fan will

 operate

when the temperature of front grill of heater is near 50°C.

When temperature reduced to about

 

40°C The thermostat cut-off and fan will stop working. It will cool

 the 

heater

( models BX9,BX15 & BX22

)

6.10

After using , turn off the heater

 then

, pull out the plug .

6.11

If Overheating occurs 

the Non-self-reset thermostat will

 

shut down the appliance . Remove the plug from the

socket and let the appliance cool down ,then use a steel pin to

 

touch the Non-self-reset thermostat button.

When you hear a clear click it means the electric circuit is

 reset

,put the plug back into the socket and switch the

heater on. Please see the figure manual “RESET” button as below:

damaged.

 

not

 

is

 

it

 

ensure

 

to

 

heater

 

 

 

the

7. Cleaning and Maintenance

7.1

Before cleaning the appliance ,disconnect it from the socket and let it cool down . The enclosure is easily to get

dirty ,wipe it often with soft sponge.For every dirty parts, wipe with a sponge dipped in <50°C water and mild

detergent,then dry the heater enclosure with clean cloth.Be careful not to let the water enter the appliance. Don’t

splash water onto the heater,never use solvent like gasoline, isoamyl acetate toluene etc. to clean the heater,in order to

protect the enclosure.

7.2

Clean the cord and plug ,dry and pack it in a plastic bag.

7.3

When you store the heater ,let it cool down first ,keep it dry . Then cover it with a plastic bag, put in a packing box and

store it in a dry ,ventilated place.

8. Trouble shooting:

You can solve many common problems easily ,saving you the cost of a possible service call. Try the suggestions below to

see if you can solve the problem before calling the service centre.

Problem

Possible cause

Treatment

The heater does not

operate,even when it is

plugged in and the

switch,thermostat are

switched on .

The plug is loose,bad connection

Pull out the plug, check the connection of

the plug and socket. Then connect

again.

No power in socket outlet

Insert the plug in a proper socket

The heating element glowing

The input voltage is too high or too low

Use power supply according to the rating

on the label

The air inlet grill is blocked

Keep the heater far way from articles like

curtain,plastic bag, paper and other

things which can cover the inlet or can

be easily cover on the air inlet

The appliance do not heat

up, only ventilator worked

The switch was not put at heating setting Turn the switch to heat setting

The thermostat operated

Turn the thermostat and listen if there is

open/close

sound

. If there is no click and

the thermostat is not damaged, the

heater will automatic switch on when the

appliance cooled down

The Non-self resetting cut-out operated

(only for the device with this function)

Disconnect the power , h

o

ld

a pin

and

insert it in the reset hole on the control

panel ,press down the reset button and

connect the circuit

Abnormal noise

The appliance is not stands upright

Put the heater on a level surface

Disposal

Environmental Protection

Waste electrical production should not be disposed of with household waste. Please recycle where facilities

exist. Check with your Local Authority or retailer for recycling advice.