Climate Caddy ACC-HTR09 User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

48V Heater and Fan

PERMANENT MOUNT
USER MANUAL

Visit us on the web
by scanning or go to:

www.climatecaddy.com

Thank you for choosing Climate Caddy for
your electric cart heating and cooling
needs!

By purchasing Climate Caddy you have received new,
patent pending heating and cooling technology that we
hope you will love.

We truly appreciate your business! Please let us know if we
can help in any way. Your feedback is important to us as
we constantly look for ways to improve our products.

Best Regards,

Climate Caddy Team

844-233-4121

TABLE OF CONTENTS

Page 3

– Case Contents

Page 5

– Yamaha Installation Instructions

Page 9

– E-Z-GO Installation Instructions

Page 12

– Club Car Installation Instructions

Page 15

– Mount Instructions

Page 16

– Operating Guide

Page 18

– Warnings, Maintenance & Troubleshooting

Page 19

– Battery Reference Guide

Page 22

– Warranty Information

SAFETY

Only operate the Climate Caddy while module is attached to its base and
securely mounted in the vehicle.

Do not block the Climate Caddy air intake.

Remove jewelry before hooking up to the battery to make sure that metal
jewelry such as bracelets and rings do not come in contact with battery
terminals and cause shorting.

Climate Caddy is made to be used
on 48 Volt Golf Carts only. Do not
attempt to hookup to a non-48 Volt
Cart as damage to the Climate
Caddy may occur.

Disclaimer: Many things can affect the driving range of the 48 volt
electric Golf Cart including ambient temperature, terrain, driving
conditions, payload, driving habits, battery age and tire pressure.

A Golf Cart Enclosure is recommended for maximum heater
performance and efficiency. Operating the Climate Caddy heater modes
without an Enclosure will further reduce Golf Cart driving range.

YAMAHA INSTALLATION INSTRUCTIONS

1. Remove Golf Cart Seat, Rubber Mat, and Dash Cup Holder

panel.

2. Run fish line and fish harness through channel opening.

a. Feed fish line through battery compartment channel opening

as shown.

b. Tape Wiring Harness (I) connectors along the fish line 3 places

so that connectors do not overlap as shown. This will allow
enough clearance for harness to pass through opening.

c. Pull on fish line to feed harness through channel opening.

d. Remove tape from harness.

3. Route Wiring harness along channel into key switch area as shown.

Note: Use tape to hold harness in channel.

4. Connect Accessory Switched Power Adapter (H) to back of key

switch and orange wires as shown.

5. Reinstall Rubber Mat.

6. Install Velcro Ties (J) using existing bolts 2 places as shown.

Note: The Velcro ties are intended to hold harness and
connectors when not in use. If only one Climate Caddy will
be installed, then the extra harness and connector can be
doubled back and stored under the rubber mat.

7. Connect Wiring Harness (I) to battery terminals.

a. Connect the red wire to positive battery terminal as per

battery reference guide on page 19.

b. Connect the black wire to negative battery terminal as per

battery reference guide on page 19.

c. Use cable ties to dress wire appropriately.

Note: Battery diagrams are representative and may not match
actual configuration. Always confirm correct terminals before
hooking up the Climate Caddy.

8. Reinstall Golf Cart Seat.

9. Install preferred Climate Caddy Mount to chosen location.

Note: To install
into an existing
cup holder, use
the Cup Mount.
Use the Tripod
Mount to install
directly onto the
dash.

10. Continue to page 15

for mount installation
instructions.

EZ-GO INSTALLATION INSTRUCTIONS

1. Remove Golf Cart Seat and Rubber Mat.

2. Run fish line and fish harness through channel opening.

a. Feed fish line through battery compartment channel opening as

shown.

b. Tape Wiring Harness (I) connectors along the fish line 3 places

so that connectors do not overlap as shown. This will allow
enough clearance for harness to pass through opening.

c. Pull on fish line to feed harness

through channel opening.

d. Remove tape from harness.

3. Route Wiring harness along channel to

front of vehicle as shown.

Note: The two orange wires with blue
connectors will not be used for this install.
Double back the orange wires into the
channel and secure with cable tie to store.

4. Reinstall Rubber Mat.

5. Install Velcro Ties (J) using existing bolts 2 places as shown.

Note: The Velcro ties are intended to hold harness and
connectors when not in use. If only one Climate Caddy will be
installed, then the extra harness and connector can be doubled
back and stored under the rubber mat.

6. Connect Wiring Harness (I) to battery terminals.

e. Connect the red wire to positive battery terminal as per

battery reference guide on page 19.

Connect the black wire to negative battery terminal as
per battery reference guide on page 10.

g. Use cable ties to dress wire appropriately.

Note: Diagrams are
representative and may
not match actual
configuration. Always
confirm correct
terminals before
hooking up the Climate
Caddy.

Install E-Z-GO Switched Power Adapter (M) as shown.

8. Reinstall Golf Cart Seat.

9. Install preferred Climate Caddy Mount to chosen location.

Note: To install into an existing cup holder, use the Cup Mount.
Use the Tripod Mount to install directly onto the dash.

10. Continue to page 15 for mount installation instructions.

CLUB CAR INSTRUCTIONS

1. Remove Golf Cart Seat and Rubber Mat.

2. Unscrew the Front Dash panel and let it hang loosely as shown

in step 7.

3. Feed Wiring Harness (I) through battery compartment opening.

4. Route Wiring harness along channel to front of vehicle as shown.

5. Reinstall Rubber Mat.

6. Connect Wiring Harness (I) to battery terminals.

a. Connect the red wire to positive battery terminal as per

battery reference guide on page 19.

b. Connect the black wire to negative battery terminal as

per battery reference guide on page 19.

c. Use cable ties to dress wire appropriately.

Note: Diagrams
are representative
and may not
match actual
configuration.
Always confirm
correct terminals
before hooking
up the Climate
Caddy.

Attach
Switched
Power as
shown.

8. Reinstall Golf Cart Seat.

9. Reinstall Front Dash Panel while installing Velcro Ties (J) using

existing bolts 2 places as shown.

Note: The Velcro ties are intended to hold harness and
connectors when not in use. If only one Climate Caddy will be
installed, then the extra connector can be doubled back and
stored under the rubber mat.

10. Install preferred Climate Caddy Mount to chosen location.

Note: To install into an existing cup holder, use the Cup Mount.
Use the Tripod Mount to install directly onto the dash.

IF USING THE CUP MOUNT (B)

Depress locks on side of Cup
Mount & rotate Bottom to
disengage teeth.

Place Cup Mount assembly in
dash cup holder. Insert screw
(F) with washer (G) & nut plate
(D) through the cup holder’s
drain hole (Do not tighten).

Push down Cup Mount Top
Piece to set the cup mount
depth. The Lip seal will
conform to the varying dash
surface to ensure there are no
gaps. Tighten screw (F).

Snap the Climate Caddy
Module onto the Cup Mount
Clip.

IF USING THE TRIPOD MOUNT (C)

a. Place the Tripod Mount onto the chosen mounting location and secure

with Self Tapping Screws (E) 3 Places.

Note: After placing the first

screw, rotate the Mount Clip to access each screw hole as shown.

b. Attach Climate

Caddy to Mount
Clip.

c. Plug Harness into

Climate Caddy.

Note: If using the
optional USB
accessory, you
will need to plug it
into the Climate
Caddy harness.

OPERATING INSTRUCTIONS

The Climate Caddy has four modes of operation with a color coded LED
indicator:

1. Normal

“Air Only” Flow (Blue LED)

Maximum “Air Only” Flow (Blue LED)

3. Normal Heat (Orange LED)

4. Maximum Heat (Red LED) with 45 Second Hot Boost*

*When in mode 4, the Climate Caddy will run at maximum heat and air
for 45 seconds and then automatically switch back to mode 3 to
conserve battery. To reset the power boost, turn knob to mode 3 and
back to mode 4.

Bi-level vent system

The three center fins can be moved to adjust the air flow direction.
Rotating the fins to their maximum upward position will partially close the
front vent and send air out the side vents, towards the floor. The side
vents are also ideal for warming your hands.

Electronic Eye

The Electronic Eye monitors the Golf Cart passenger compartment and
automatically turns off the Climate Caddy after 30 seconds of no
occupants being detected.

When in heater modes 3 & 4, the LED indicator will turn blue after 30
seconds to indicate the Climate Caddy is powering off.

When in air only modes 1 & 2, the fan speed will slow after 30 second to
indicate the Climate Caddy is powering off.

The heater will automatically resume when the Electronic Eye detects a
passenger at the last chosen mode.

Battery Fail-Safe Sensor

The Climate Caddy will automatically power off after the total battery
charge drops below a preset voltage. This prevents on course battery
drain should you start play without a full battery charge.

Note:

Turn the control knob slowly to allow the Climate Caddy’s

Power Management Technology to smoothly transition between
operating modes. This will ensure maximum efficiency with
minimum battery drain.

WARNINGS:

• Do not drop or submerge the Climate Caddy in water or liquid.

• Do not block the Climate Caddy air intake.

• Shorting across battery terminals may cause battery explosion.

MAINTENANCE:

• Periodically check Electronic Eye lens for smudges or debris and gently
wipe clean with a microfiber cloth. Contamination of the Electronic Eye
lens can impede its ability to accurately detect occupants in the vehicle
cabin.

• Regularly check and maintenance the Golf Cart batteries as instructed
in your Golf Cart owner

’s manual.

READ ALL WARNINGS AND

SAFETY PRECAUTIONS IN GOLF CART MANUAL BEFORE
SERVICING VEHICLE.

TROUBLESHOOTING:

• Make sure the Golf Cart batteries are fully charged. The Battery Fail
Safe Sensor prevents the Climate Caddy from powering on if the total
battery charge drops below a preset voltage. Many factors can affect the
battery charge including age, condition, ambient temperature, and
electrolyte levels.

Note: One or more bad batteries with low-voltage can cause the fail-
safe sensor to activate and prevent the Climate Caddy from
powering on.

BATTERY REFERENCE GUIDE

To correctly power the Climate Caddy, attach the Red Wire to the 48V
output terminal having a red wire leading away from the battery pack,
and the Black Wire to the 48V ground output terminal having a black wire
leading away from the battery pack.

Note: Diagrams are representative and may not match actual
configuration. Always confirm correct terminals before hooking up
the Climate Caddy.

Climate Caddy Two Year Limited Warranty

TSI Products, Inc./Climate Caddy Products are warranted to the original retail
purchaser, to be free from defects in materials and workmanship except as otherwise
provided herein. This warranty is not transferrable and is effective from the date of
the original purchase date.

This Warranty Covers:

1. During the first year from the original retail purchase date, TSI Products/Climate

Caddy will, at its option repair or replace defective components, including labor
and cost of shipment to original consumer.

2. After the first year from original retail purchase date, up to the term of the

warranty, TSI Products/Climate Caddy will repair or replace defective
components with an identical or reasonably equivalent new component for a
$255.00 service charge which includes labor and cost of shipment to the
original consumer.

The Warranty Does Not Cover:

1. Cost of shipping the product to TSI Products/Climate Caddy.

2. Normal wear, scratches or fading of the product.

3. Damage caused by abuse, misuse, neglecting to follow use procedures, failure

to follow installation procedures (See instructions in product package) or
product modifications made by consumer.

4. Damage to home or vehicle electrical system or components caused by

inadequate wiring to the product plug-in point.

5. Damage to any object placed close (see instructions on product package) to the

air output of the heater.

6. Damage caused by dropping of heater.

7. Product sold outside the USA.

8. Consequential damages, incidental damages or expenses, including damages

to property. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so above limitation or exclusion may not apply to you.

Procedures for Warranty service:

1. Contact TSI Products/Climate Caddy (844-233-4121) for a return authorization

number. Write this number on the carton being returned to TSI
Products/Climate Caddy.

Attach, to the product itself, a tag showing your name, address, phone number,
description of the problem and proof of retail purchase date. Enclose a
cashier’s check, check, Visa or MasterCard information or money order for
applicable service charges.

Package the product carefully to ensure that no damage occurs during return
shipment. Return the product, postage prepaid, to TSI Products/Climate Caddy.

Implied Warranty:

This warranty is limited to the provisions clearly stated herein. Any implied
warranties, warranties of merchantability, warranties of fitness for a particular
use are excluded.

If any provision of this warranty is prohibited by federal, state, or local law, that
provision shall not be applicable.

Visit www.ClimateCaddy.com to learn more about our growing lineup of
accessories including:

Portable Mount Kit

A portable mounting solution that adjust to fit any sized cup
holder. Includes a convenient Carrying Case and the
Monarch Cord Keeper, a lay-flat wiring harness.

Part# SCC7701

Dual USB Power Accessory

Recharge your Cell Phone and other mobile devices. Easily
attaches to the Climate Caddy Cup-Base.

Part# SCC7705

Phone Holder Accessory

Safely store your Cell Phone and other mobile devices.
Snaps onto the Climate Caddy and accommodates a wide
range of phone sizes and styles.

Part# SCC7706

Ask a Question ?