Cli-mate CLI-AP30 Installation & Operating Instructions Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

CLI-AP30 | Installation & Operating Instructions

Air

Purification

System

Congratulations on your purchase of a
Cli~Mate Air Purification System

This Air Purifier improves the quality of the air in your home by helping to eliminate airborne matter such as allergens,
microbes and unpleasant odours.

Note: Please read through the instructions carefully before using or installing the product and ensure that the
manual is kept in a safe place for future reference.

The system must be properly installed and located in accordance with the installation instructions before it is used.

During the set up of this product if you have any questions / comments / issues DO NOT RETURN TO STORE.
FOR SERVICE AND TECHNICAL ADVICE ON THIS PRODUCT, FREE CALL 1300 764 325.

Electrical Requirements:
Australia / New Zealand 240V / 230V 50Hz
Due to manufacturing alterations product may
vary slightly from the pictured.

CUSTOMER HOTLINE: 1300 764 325

www.cli-mate.com.au/warranty-and-registration
Aquaport Corporation Pty Ltd
PO Box 81 Findon SA 5023 Australia
Telephone: 08 8354 0711
Facsimile: 08 8354 0722
Email: aquaport@aquaport.com.au
Web: www.cli-mate.com.au
Social: /climatebrand @climatebrand

INSTALLATION AND OPERATING INSTRUCTIONS

SAFETY PRECAUTIONS

Read all instructions carefully.
• All components need to be installed in accordance with the user

manual instructions for correct performance of unit.

• This appliance should be used in conjunction with a safety switch.
• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.

• Do not operate any appliance with a damaged cord or plug or after

the appliance malfunctions, or has been damaged in any manner.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.

• Children should be supervised to ensure that they do not play with

the appliance.

• Do not use appliance for other than intended use.
• Do not disassemble, repair or re-form the unit, it may cause injury,

fire or other malfunctions. A qualified service agent must make all
service adjustments. Removing any part or attempting to service
the dryer will void the warranty.

• Unplug from outlet when not in use and before cleaning. Never

plug in or unplug unit with wet hands.

• Do not use unit outdoors or expose to greasy or damp

environments.

• Keep the rear air inlet and outlet is free from air blocking

materials such as clothing, plastic bags or papers. Air flow is
required for the unit to operate effectively.

• Place unit on a flat location at least 30cm from wall or other

appliances.

• When the unit is in operation, keep all body parts, jewellery, hair

and loose clothing away from the openings

• Unit must be placed on a stable flat surface to reduce possible

excessive vibration and noise.

• Keep the dryer away from fire, flammable gas, combustible

products or vapours, and corrosive substances.

• Do not operate the unit without filters
• When transporting the air purifier, always hold the handles on the

side of the unit

• Do not remove the lid of the unit when it is in operation.
• To protect against fire, electric shock and personal injury, do not

immerse cord, plugs, or appliance in water or other liquid.

• Do not place on or near a hot gas, electric burner or heating

appliance.

• Check voltage to be sure that the voltage indicated on the

nameplate agrees with your voltage.

INSTALLATION AND OPERATING INSTRUCTIONS

PRODUCT FEATURES

Filters

The 3 layer filter contains a pre-filter, a HEPA filter and an activated
carbon filter.

• The pre-filter traps larger particles such as dust, pet hair and

large-sized allergens.

• The HEPA filter (Grade H12) removes 99.5% of particles as

small as 0.3 microns and greater from the air. It is capable of
removing smoke, dust, pollen, pet dander, mold spores, bacteria
and allergens in the air.

• The Activated carbon filter absorbs common household odours,

VOCs, cigarette odours, chemical fumes and smoke.

Ionizer

In addition to the filters, this air purifier generates negatively
charged oxygen molecules (different than ozone) which attach to
particles in the air which makes it easier for the air purifier to trap.
Airborne particles are attracted to the negative ions in an effect
similar to static electricity.

UV TiO2 Photocatalyst

This air purifier also utilises safe and advanced UV TiO2
Photocatalyst technology as a way of sterilising the air.

This air purification method involves a broad-spectrum UV-C light
reacting with a thin film of Titanium Dioxide which produces highly
reactive electrons. These combine with airborne microbes.
Once combined, a chemical reaction takes place between the
super-charged ion and the pollutant which effectively breaks
down the microbes.

INSTALLATION AND OPERATING INSTRUCTIONS

COMPONENT IDENTIFICATION

1. Display panel

2. Control buttons

3. Air outlet cover

4. Hidden handles

5. Remote control

6. Air inlet

7. Ionizer

8. Pre-filter, HEPA and active carbon filter

9. UV TiO2 photocatalyst filter

10. Back cover

INSTALLATION AND OPERATING INSTRUCTIONS

CONTROL PANEL/BUTTONS

1. Speed options

Allows selection for desired speed setting- turbo, high, low and
sleep. Default setting at low speed

Filter timer reset button

Press and hold for 3 seconds to reset filter timer

2. Power button

Turns unit on/off

3. Timer options

To set automatic off timer at 1, 4 or 8 hour settings

REMOTE CONTROL

I. On/off

II. Child-safety lock

III. Auto-mode

IV. Speed options

V. Sleep mode

VI. Off timer options

Note:

• Avoid storing the remote control in

direct sunlight

• The battery for this remote control is

for initial use only and will need to be
changed

• When replacing battery, always use a

3V lithium coin battery

• When the unit will not be used for an

extended period, remove the battery
from the remote to prevent battery
fluid leakage

INSTALLATION AND OPERATING INSTRUCTIONS

DISPLAY PANEL

1. Power Indicator

Illuminates blue when power is ON

Filter Change

Indicator Light will flash blue when filter

needs to be changed

Child-Lock

Function Indicator Illuminates Green when

Child Safety Lock is ON

2. Fan Speed

Indicator

Turbo speed

High speed

Low speed

Sleep (Ultra-quiet mode)

3. Timer Indicator

1 hour

4 hours

8 hours

4. Automatic

Mode Indicator

Red - Poor air quality

Purple - Moderate air quality

Blue - Good air quality

Remote Control Signal Receiver

INSTALLATION AND OPERATING INSTRUCTIONS

OPERATION INSTRUCTIONS

1. Plug unit into power socket, unit will beep and control panel

lights will illuminate blue before extinguishing. POWER light

will be lit green. Unit is now in standby mode.

2. Press POWER button

to turn unit on. The unit will beep and

the fan will start running. The air outlet cover will automatically
open and display panel lights will illuminate indicating current
settings.

Note:

The purification default setting is at LOW speed mode.

3. To select speed,

press until LED Light is on desired speed-

LOW, HIGH, TURBO, SLEEP.

Note:

To select SLEEP mode on the remote control, press

button.

4. To set automatic off timer, press

until LED light is on

desired time 1/4/8 hours. Unit will automatically switch off
once selected time duration has lapsed.

5. To select AUTO-MODE, press

on the remote control. The

auto-mode icon on the display panel will light up. The icon

colour will change indicating the current air quality. The fan
speed of the unit will change automatically depending on the
air quality as detected by the dust and odour sensors.

PRODUCT SPECIFICATIONS

Air Purifier

Model Code

CLI-AP30

Dimensions (mm)

H679 x W394 x D153

Coverage area

Up to 25m

Power consumption

55 watts

Net weight

7.2 kg

Gross weight

8.4 kg

Germicidal UV-C light

8W/253.7nm

Air flow

176m

Air change per hour

30m

x 6

Clean air delivery rate

105cfm (smoke)

Ozone release rate

Less than 0.05PPM

Noise level in Turbo Mode

<58dB

Noise level in Sleep Mode

<28dB

Replacement filter

CLI-RF-AP30

INSTALLATION AND OPERATING INSTRUCTIONS

6. To activate CHILD-LOCK function, press

on the remote

control. ‘CHILD LOCK’ light on the unit will be lit when this
feature is activated. This function will lock the control buttons
on the unit and remote control

Note:

To deactivate the CHILD LOCK function, hold the

button on the remote control for 3 seconds until the CHILD LOCK
LED light on the unit extinguishes.

During the set up of this product if you have any questions /
comments / issues DO NOT RETURN TO STORE FOR SERVICE
AND TECHNICAL ADVICE ON THIS PRODUCT FREE CALL
1300 764 325

Good air quality Moderate air quality Poor air quality

Indicator
light

Blue

Purple

Red

Operating
speed

Sleep

Low

High

INSTALLATION AND OPERATING INSTRUCTIONS

CLEANING AND MAINTENANCE

Before carrying out any maintenance or cleaning of the unit, make
sure that the power to the unit is turned off and power cord is
unplugged from the power socket.

External cleaning of unit:

• Do not clean unit with any abrasive cleaning agents or solvents

• Do not apply any water directly to the unit of cleaning

• Only use a soft clean cloth for all cleaning purposes

• Clean the air inlet and outlet with a dry cloth, soft brush or

vacuum cleaner

CLEANING THE PRE-FILTER

It is recommended that the Pre-filters (the removable white layer)
are cleaned every 1-2 weeks of unit operation, depending on the
air quality of the room

To clean the Pre-filter:

1. The removable Pre-filter is attached by Velcro. Gently peel away

the Pre-filter.

2. Fill the sink with lukewarm water and gently hand wash the

Pre-filter under the water for 2-3 minutes or until it is
completely clean.

3. Rinse the Pre-Filter with clean tap water.

4. Use a towel to remove any excess water from the Pre-Filter

5. Allow the Pre-filter to dry for 12-24 hours

6. When the Pre-filter is completely dry, re-attach and place back

into the air purifier. Note: When placing the filters back into the
air purifier, ensure that the white belts are facing outwards and
that the Pre-filters are facing towards the air inlet

INSTALLATION AND OPERATING INSTRUCTIONS

CLEANING THE HEPA AND ACTIVATED CARBON FILTER

It is recommended that the HEPA and activated carbon filters are
cleaned every 100-500 hours of unit operation, depending on the
air quality of the room.

To clean the HEPA and Activated Carbon Filter:

1. Turn off unit and disconnect the power.

2. Place both hands at the bottom corners of the rear cover, and

pull out.

3. Pull out the 4 filters by the white belt attached

4. Gently peel away the Pre-filter layers

5. Run a vacuum cleaner with a nozzle or brush attachment on

low power setting along the HEPA (white side) and Activated
Carbon (black side) filters to pick up the dust and various
particles.

6. Re-attach Pre-filter layers and place back into the air purifier.

Note: When placing the filters back into the air purifier, ensure
that the white belts are facing outwards and that the Pre-Filters
are facing towards the air inlet

REPLACING FILTER

When the lifespan of the 3-layer filter reaches it end, the POWER

light will flash blue, indicating that it needs to be changed.

Discard the old filter and replace with a new one. It is not reusable.

The lifespan and duration of the filter depends on the air quality
and surrounding environment. The higher level of pollutants, the
shorter the filter lifespan. It is advisable to change the filter at
least every 8 months or 1500 hours of unit operation.

Cli~Mate Replacement Filter Product Code: CLI-RF-AP30.

HOW TO REPLACE THE FILTER

1. Turn off unit and disconnect the power.

2. OPEN THE REAR COVER: Place both hands at the bottom

corners of the rear cover, and pull out.

3. REMOVE THE FILTER: Pull out the filters by the white belt

attached and discard.

4. INSTALL NEW FILTER: Replace with new filters. Ensure that

that the white belt is facing outwards and that the Pre-Filter is
facing towards the air inlet.

5. Reattach the rear cover.

6. Hold down Speed

button on the unit to reset the unit.

INSTALLATION AND OPERATING INSTRUCTIONS

TROUBLE SHOOTING

BEFORE YOU CALL FOR SERVICE PLEASE REVIEW THE TROUBLE SHOOTING TIPS FIRST.

Problem

Possible Causes

What To Do

No Power

1. Unit is not plugged into wall socket.

1. Check connection to wall socket.

Unit overheating

1. Air ventilation around unit

not sufficient

2. Air inlet or air outlet is being obstructed

or blocked by foreign objects

3. Internal malfunction

1. There must be at least 30cm between unit and wall

or other appliances

2. Ensure there are no object obstructing the air inlet or

air outlet

3. Return unit to service agent. Call customer care

The unit is not effective

1. Filters may be heavily soiled and due for

replacement

1. Replace filter

Excessive/loud noise

1. Unit is on an uneven surface

2. Foreign objects have fallen into the unit

3. Faulty internals

1. Ensure the unit is placed on a level surface

2. Ensure that no foreign objects have fallen into the unit

via the air outlet.

3. Call customer care

INSTALLATION AND OPERATING INSTRUCTIONS

Problem

Possible Causes

What To Do

The remote control does
not work

1. Battery could be dead, depleted or not

correctly installed

2. Remote is not pointed directly at the unit

3. Remote control distance is out of range

1. Replace battery. Ensure the battery is correctly installed

2. Aim the remote at the small square in the middle of the

control display

3. Remote effective distance approx. 5m

Odour coming from
the air outlet

1. Filter may be heavily soiled and due for

replacement

1. Replace filter

INSTALLATION AND OPERATING INSTRUCTIONS

Your Aquaport 12 Month Repair or Replacement Warranty

Aquaport warrants this appliance to the first purchaser and subject
to the stated conditions:
Warranty covers any defects in material or workmanship in the
manufactured product within the first twelve months from the date
of purchase.
To make a warranty claim you must call Aquaport on toll free number
1300 764 325 for instructions. If a product is found to be faulty there
is a 90 day return policy from the date of purchase.
For warranty claims outside of 90 days from date of purchase, product
will be repaired or replaced at our discretion. Repair or replacement
costs of the product will be covered under warranty by Aquaport.
Goods presented for repair may be replaced by refurbished goods of
the same type rather than being repaired. Refurbished parts may be
used to repair the goods.
Warranty does not cover filters which are consumable unless proven to
have defects in material or workmanship in the manufactured product.
Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if goods fail to be of acceptable quality and the
failure does not amount to a major failure.

Conditions of this Warranty:

1. This product has been fully installed in accordance

with the user manual installation instructions.

2. The warranty extends only to repairing or replacing

any component that proves to be defective in material

or workmanship.

3. The warranty does not cover defects occasioned by

misuse, alterations, accidents, or used for other than the

intended purpose.

4. The warranty does not cover damage to the product

caused by accident, fire, or floods.

5. Proof of purchase is required for warranty claims.

Please keep purchase receipt in a safe place.

To enable us to register your warranty and provide service should a
problem occur, we recommend you register your warranty online at:

www.cli-mate.com.au/warranty-and-registration

Aquaport Corporation Pty Ltd

5 John Street Flinders Park,
South Australia 5025

Customer Care 1300 764 325

INSTALLATION AND OPERATING INSTRUCTIONS

CUSTOMER HOTLINE: 1300 764 325

Aquaport Corporation Pty Ltd

PO Box 81 Findon SA 5023 Australia

Telephone: 08 8354 0711

Facsimile: 08 8354 0722

Email: aquaport@aquaport.com.au

Web: www.cli-mate.com.au

Social: /climatebrand @climatebrand

Ask a Question ?