Cli-mate CLI-AP20 Installation & Operating Instructions Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

CLI-AP20 | Installation & Operating Instructions

Air

Purification

System

Congratulations on your purchase of a
Cli~Mate Air Purification System

This Air Purifier improves the quality of the air in your home by helping to eliminate airborne matter such as
allergens and unpleasant odours.

Note: Please read through the instructions carefully before using or installing the product and ensure that the
manual is kept in a safe place for future reference.

The system must be properly installed and located in accordance with the installation instructions before it is used.

During the set up of this product if you have any questions / comments / issues DO NOT RETURN TO STORE.
FOR SERVICE AND TECHNICAL ADVICE ON THIS PRODUCT, FREE CALL 1300 764 325.

Electrical Requirements:
Australia / New Zealand 240V / 230V 50Hz
Due to manufacturing alterations product may
vary slightly from the pictured.

CUSTOMER HOTLINE: 1300 764 325

www.cli-mate.com.au/warranty-and-registration
Aquaport Corporation Pty Ltd
PO Box 81 Findon SA 5023 Australia
Telephone: 08 8354 0711
Facsimile: 08 8354 0722
Email: aquaport@aquaport.com.au
Web: www.cli-mate.com.au
Social: /climatebrand @climatebrand

INSTALLATION AND OPERATING INSTRUCTIONS

SAFETY PRECAUTIONS

Read all instructions carefully.
• All components need to be installed in accordance with the user

manual instructions for correct performance of unit.

• This appliance should be used in conjunction with a safety switch.
• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.

• Do not operate any appliance with a damaged cord or plug or after

the appliance malfunctions, or has been damaged in any manner.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.

• Children should be supervised to ensure that they do not play with

the appliance.

• Do not use appliance for other than intended use.
• Do not disassemble, repair or re-form the unit, it may cause injury,

fire or other malfunctions. A qualified service agent must make all
service adjustments. Removing any part or attempting to service
the dryer will void the warranty.

• Unplug from outlet when not in use and before cleaning. Never

plug in or unplug unit with wet hands.

• Do not use unit outdoors or expose to greasy or damp

environments.

• Keep the rear air inlet and outlet is free from air blocking

materials such as clothing, plastic bags or papers. Air flow is
required for the unit to operate effectively.

• Place unit on a flat location at least 30cm from wall or other

appliances.

• Unit must be placed on a stable flat surface to reduce possible

excessive vibration and noise.

• Keep the dryer away from fire, flammable gas, combustible

products or vapours, and corrosive substances.

• Do not wash or reuse the filters.
• Do not operate the unit without filters.
• To protect against fire, electric shock and personal injury, do not

immerse cord, plugs, or appliance in water or other liquid.

• Do not place on or near a hot gas, electric burner or heating

appliance.

• Check voltage to be sure that the voltage indicated on the

nameplate agrees with your voltage.

Air Purifier

Model Code

CLI-AP20

Product Dimensions

H394 x W310 x D139mm

Coverage area

Up to 20m

Power consumption

35 watts

Net weight / Gross Weight

3.5 kg / 4.2 kg

Air Change/ Hr

30m2 x 4.5

Air Flow /Hr

133m

Clean air Delivery rate

75cbm (smoke)

Power cord length

1.8m

Noise level in Turbo Mode

58dB

Noise level in Sleep Mode

28dB

Replacement Filter

CLI-RF-AP20

INSTALLATION AND OPERATING INSTRUCTIONS

OPERATION INSTRUCTIONS

1. Plug unit into power socket, unit will beep and control panel

lights will illuminate before extinguishing. Unit is now in
standby mode.

2. Press POWER button

to turn unit on. The unit will beep

and display panel lights will illuminate indicating current
settings.

Note:

The purification default setting is at LOW speed mode.

3. To select speed, press

until LED Light is on desired speed-

LOW, MEDIUM, HIGH, SLEEP respectively.

4. To set automatic off timer, press

until LED light is on

desired time 1/4/8 hours. Unit will automatically switch off
once selected time duration has lapsed

5. To select AUTO-MODE, press

and the AUTO led light will

be lit. The unit will now start purifying in a loop cycle on these
settings: HIGH speed for 2 hours MEDIUM speed for 2 hours
LOW speed for 2 hours.

6. To activate CHILD-LOCK function, hold down AUTO MODE

for 3 seconds or until CHILD LOCK light is lit.

Note:

To deactivate the CHILD LOCK function, hold down AUTO

MODE

for 3 seconds or until CHILD LOCK light extinguishes.

During the set up of this product if you have any
questions / comments / issues DO NOT RETURN TO STORE
FOR SERVICE AND TECHNICAL ADVICE ON THIS PRODUCT FREE
CALL 1300 764 325

DISPLAY PANEL

HIGH | MEDIUM | LOW | SLEEP

- Indicates the Fan speed

POWER

: Power Indicator:

Illuminates green when power

is turned ON.

Filter change indicator: Light will flash when the filter

needs to be changed.

AUTO:

Automatic Mode

Child Lock

Child safety lock

1hr | 4hr | 8hr:

Timer indicator

INSTALLATION AND OPERATING INSTRUCTIONS

COMPONENT IDENTIFICATION

POWER

Turns unit ON/OFF

SPEED

Allows selection for desired fan speed setting: SLEEP,
LOW, MEDIUM and HIGH

AUTO MODE

Operates in a loop cycle on these settings: HIGH speed
for 2 hours - MEDIUM speed for 2 hours - LOW speed for
2 hours

TIMER

To set automatic OFF timer at 1,4,8 hour settings

I. Front Cover
2. Air Inlet

3. Triple Layer Filter

(Initial Filter, HEPA filter and
active carbon filter)

4.  Display Panel
5.  Control Buttons
6. Handle
7.  Air Outlet
8.  Wall Mounts

CONTROL PANEL/BUTTONS

4 5

INSTALLATION AND OPERATING INSTRUCTIONS

FILTERS

The dual layer filter contains a pre-filter, a HEPA filter and an
activated carbon filter.

The pre-filter traps larger particles such as dust, pet hair and large-
sized allergens.

The HEPA filter (grade H12) removes 99.5% of particles as small
as 0.3 microns and greater from the air. It is capable of removing
smoke, dust, pollen, pet dander, mold spores, bacteria and
allergens in the air.

The Activated carbon filter absorbs common household odours,
VOCs, cigarette odours, chemical fumes and smoke.

CLEANING AND MAINTENANCE

Before carrying out any maintenance or cleaning of the unit, make
sure that the power to the unit is turned off and power cord is
unplugged from the power socket.

External cleaning of unit:

• Do not clean unit with any abrasive cleaning agents or solvents

• Do not apply any water directly onto the unit

• Only use a soft clean cloth for all cleaning purposes

• Clean the air inlet and outlet with a dry cloth, soft brush or

vacuum cleaner

CLEANING THE PRE-FILTER

It is recommended that the Pre-filter (the removable white layer) is
cleaned every 1-2 weeks of unit operation, depending on the air
quality of the room

To clean the Pre-filter:

1. The removable Pre-filter is attached by Velcro. Gently peel away

the Pre-filter.

2. Fill the sink with lukewarm water and gently hand wash the

Pre-filter under the water for 2-3 minutes or until it is completely
clean.

3. Rinse the Pre-filter with clean tap water.

INSTALLATION AND OPERATING INSTRUCTIONS

4. Use a towel to remove any excess water from the Pre-filter

5. Allow the Pre-filter to dry for 12-24 hours

6. When the Pre-filter is completely dry, re-attach and place back

into the air purifier. Note: When placing the filters back into the
air purifier, ensure that the white belts are facing outwards and
that the Pre-filters are facing towards the air inlet

CLEANING THE HEPA AND ACTIVATED CARBON FILTER

It is recommended that the HEPA and activated carbon filters are
cleaned every 100-500 hours of unit operation, depending on the
air quality of the room.

To clean the HEPA and Activated Carbon Filter:

1. Turn off unit and disconnect the power

2. Place both hands at the bottom corners of the front cover, and

pull out

3. Pull out the filter by the white belt attached

4. Gently peel away the Pre-filter layer

5. Run a vacuum cleaner with a nozzle or brush attachment on low

power setting along the HEPA (white side) and Activated Carbon
(black side) filters to pick up the dust and various particles.

6. Re-attach the Pre-filter layer and place back into the air purifier.

Note:

When placing the filters back into the air purifier, ensure

that the white belts are facing outwards

REPLACING FILTER

When the lifespan of the 3-layer filter reaches it end, the POWER
light will flash green indicating that it needs to be changed. Discard
the old filter and replace with a new one. It is not reusable.
Cli~Mate Replacement Filter Product Code: CLI-RF-AP20

The lifespan and duration of the dual layer filter depends on the air
quality and surrounding environment. The higher level of pollutants,
the shorter the filter lifespan. It is advisable to change the 3-layer
filter at least every 8 months or 1500 hours of unit operation.

HOW TO REPLACE THE FILTER

1. Turn off unit and disconnect the power.

2. OPEN THE FRONT COVER: Place both hands at the bottom

corner of the front cover, press down the buttons on the sides
while pulling out.

3. REMOVE THE FILTER: Pull out the filter by the white belt

attached and discard

4. INSTALL NEW FILTER: Replace with new filter. Ensure that

the white belt is facing outwards

5. Line up the top of the front cover first and then snap in the

lower part of the front cover. Ensure that the front cover is
firmly intact.

6. Hold down Speed

button on the unit to reset the

filter timer.

INSTALLATION AND OPERATING INSTRUCTIONS

TROUBLE SHOOTING

BEFORE YOU CALL FOR SERVICE PLEASE REVIEW THE TROUBLE SHOOTING TIPS FIRST.

Problem

Possible Causes

What To Do

No Power

1. Unit is not plugged into wall socket.

1. Check connection to wall socket.

Unit overheating

1. Air ventilation around unit

not sufficient

2. Air inlet or air outlet is being obstructed

or blocked by foreign objects

3. Internal malfunction

1. There must be at least 30cm between unit and wall

or other appliances

2. Ensure there are no object obstructing the air inlet or

air outlet

3. Return unit to service agent. Call customer care

The unit is not effective

1. Filters may be heavily soiled and due for

replacement

1. Replace filter

Excessive/loud noise

1. Unit is on an uneven surface

2. Foreign objects have fallen into the unit

3. Faulty internals

1. Ensure the unit is placed on a level surface

2. Ensure that no foreign objects have fallen into the unit

via the air outlet.

3. Call customer care

INSTALLATION AND OPERATING INSTRUCTIONS

Your Aquaport 12 Month Repair or Replacement Warranty

Aquaport warrants this appliance to the first purchaser and subject
to the stated conditions:
Warranty covers any defects in material or workmanship in the
manufactured product within the first twelve months from the date
of purchase.
To make a warranty claim you must call Aquaport on toll free number
1300 764 325 for instructions. If a product is found to be faulty there
is a 90 day return policy from the date of purchase.
For warranty claims outside of 90 days from date of purchase, product
will be repaired or replaced at our discretion. Repair or replacement
costs of the product will be covered under warranty by Aquaport.
Goods presented for repair may be replaced by refurbished goods of
the same type rather than being repaired. Refurbished parts may be
used to repair the goods.
Warranty does not cover filters which are consumable unless proven to
have defects in material or workmanship in the manufactured product.
Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if goods fail to be of acceptable quality and the
failure does not amount to a major failure.

Conditions of this Warranty:

1. This product has been fully installed in accordance

with the user manual installation instructions.

2. The warranty extends only to repairing or replacing

any component that proves to be defective in material

or workmanship.

3. The warranty does not cover defects occasioned by

misuse, alterations, accidents, or used for other than the

intended purpose.

4. The warranty does not cover damage to the product

caused by accident, fire, or floods.

5. Proof of purchase is required for warranty claims.

Please keep purchase receipt in a safe place.

To enable us to register your warranty and provide service should a
problem occur, we recommend you register your warranty online at:

www.cli-mate.com.au/warranty-and-registration

Aquaport Corporation Pty Ltd

5 John Street Flinders Park,
South Australia 5025

Customer Care 1300 764 325

INSTALLATION AND OPERATING INSTRUCTIONS

CUSTOMER HOTLINE: 1300 764 325

Aquaport Corporation Pty Ltd

PO Box 81 Findon SA 5023 Australia

Telephone: 08 8354 0711

Facsimile: 08 8354 0722

Email: aquaport@aquaport.com.au

Web: www.cli-mate.com.au

Social: /climatebrand @climatebrand

Ask a Question ?