Full Text Searchable PDF User Manual
D. No. 05A4 Version 1.0
Released on 02/06/2014
Page1 of 10
Uhlmann & Zacher GmbH
l Gutenbergstraße 2–4 l 97297 Waldbüttelbrunn l Tel.: +49 931 40672-0 l E-Mail: contact@UundZ.de l
http://www.UundZ.de
Quick Guide
Valid from Firmware 2.2.14
CX6110 Electronic Cylinder
Page2 of10
Quick Guide
Electronic Cylinder
Table of contents
1
General .......................................................................................... 3
1.1
Intended use ................................................................................................ 3
1.2
Safety and operation .................................................................................... 3
1.3
Disposal ...................................................................................................... 4
2
Product details ................................................................................. 5
2.1
CX6110 ...................................................................................................... 5
2.2
Scope of supply ........................................................................................... 5
3
Indicators ........................................................................................ 5
4
Assembly ........................................................................................ 6
4.1
General points to note ................................................................................. 6
4.2
Assembly ..................................................................................................... 6
5
Operation ....................................................................................... 7
6
Batteries .......................................................................................... 8
6.1
Changing batteries ...................................................................................... 8
6.2
Low-power opening ..................................................................................... 9
7
Technical data ............................................................................... 10
Page3 of10
Quick Guide
Electronic Cylinder
1
General
Uhlmann & Zacher GmbH
(U&Z) does not accept any
liability for the correctness
and completeness of the
information given here.
Information given in this operating manual is
subject to change without notice. In such a
case, all previous information becomes
invalid.
Uhlmann & Zacher GmbH does not accept
any liability for damage resulting from
erroneous or incomplete information.
Uhlmann & Zacher GmbH directs you to the
generally valid ESD protective measures.
1.1
Intended use
CX6110 cylinder is intended
for installation on building
doors. They should be fitted
with a corresponding lock
and fitting. Furthermore, the
CX6110 cylinder is only meant for locking
and unlocking doors.
Only the components approved by U&Z
should be used for installation. The CX6110
cylinder replaces a standard closing cylinder
and is not suitable for operating as a knob or
pressure device.
The CX 6110 cylinder is intended for
installation in DIN locks with Europrofil
cylinders.
All other uses are prohibited.
1.2
Safety and operation
No modifications of any kind
on the cylinder are permitted
except those described in the
manual.
Installation and battery
replacement may only be done by trained
personnel in accordance with this manual.
This manual should be handed over to the
user by the person installing the product.
The cylinders must only be lubricated using
the special resin-free oil.
The cylinders must not be exposed to paint or
acids.
The batteries must not be charged, opened
or heated.
Wrong polarity when inserting the batteries
can cause damage.
When changing the batteries, change both
batteries at the same time, even if one battery
appears to have adequate charge.
Page4 of10
Quick Guide
Electronic Cylinder
The cylinder must not be used in areas where
explosions can happen.
Only use the specified batteries.
If the batteries or the cylinder heat up above
the specified storage temperature, then this
can cause fire and explosion.
To avoid malfunctioning and damage, use
only original Uhlmann & Zacher parts and
accessories.
However, no liability can be accepted for
wrongly programmed cylinders. If there are
disruptions, such as access not possible for
injured persons, property damage or other
damages, Uhlmann & Zacher GmbH is not
responsible.
Unauthorised modifications and changes in
the product are not permitted.
The electronic cylinders must not be used for
locking emergency life-saving aids (e.g.
defibrillator, emergency medication, fire
extinguisher etc).
1.3
Disposal
To ensure environmentally
friendly recycling, the device,
as well as the packaging
must be disposed in an
ecologically friendly manner.
The packaging is recyclable and should not
be disposed of in the household waste but
recycled.
Batteries
Lithium batteries are
needed to make the
cylinder work. Improper
use of lithium batteries can
cause fires and explosions.
Defective or spent
accumulators and batteries must be recycled
according to the European Directives
2006/66/EG. Please keep up to date on the
local stipulations for segregation and
disposal of batteries. Correct disposal will
protect the environment and people from
negative consequences.
Page 5 of 10
Quick Guide
Electronic Cylinder
2
Product details
2.1
CX6110
CX6110:
Clex prime electronic cylinder,
standard length from 30/30 mm, special
lengths from 26/35 mm, version for internal
and external building locking doors
(depending on the execution), cylinder casing
nickel-coated brass, for transponder-keys incl.
forend screws and batteries
CX6111:
Clex prime electronic cylinder, basic
version, like CX6110, but without date/ clock
time and events memory
2.2
Scope of supply
Electronic cylinder
CX6110
2x Battery CR2, 3V
Forend screw
3
Indicators
Operation
Audible signal
Explanation of icons
Rest mode
Audible signals:
= long, deep tone
O = short, high tone
Begin programme mode
O
End programme mode
O
Transponder key not authorised
Battery warning
O O O O O
After battery change:
Page 6 of 10
Quick Guide
Electronic Cylinder
4
Assembly
4.1
General points to note
Internal and external handle must be
screwed on to the door panel such that the
cylinder can be pushed into the PC hole of
the lock without using force. Ideally, the
central axis of the cylinder is at an angle of
roughly 90 degrees to the door panel. The
knob must be in contact with the internal
door furniture, so there should be a distance
of at least 1 mm between knob and door
panel. (A)
The stud dimensions of the lock must be at
least 55 mm. (B)
90°
min. 1mm
min. 55mm
4.2
Assembly
1.
If present, remove the forend screw and
disassemble the existing cylinder.
2.
Push in CX6110 and fasten with forend
screw. (A+B)
Important:
Immediately after
assembly, make sure that the
components move freely.
A
B
A
B
Page 7 of 10
Quick Guide
Electronic Cylinder
5
Operation
1.
Insert authorised transponder key into the
electronic cylinder. (A)
2.
After reading the transponder key, the
electronic cylinder engages. (B)
3.
Turn transponder key and perform the
closing sequence. (C)
A
B
C
Page 8 of 10
Quick Guide
Electronic Cylinder
6
Batteries
6.1
Changing batteries
1.
Push in locking pins using a pointed object
and at the same time pull out the sleeve. (A)
2.
Changing batteries (ensure correct polarity).
(B)
3.
Push in locking pins and push the sleeve on
to the knob, until the locking pins latch into the
designated recesses in the sleeve. (C)
+
-
+
-
Important:
Ensure the correct
alignment of the sleeve
(pressure spring on the
negative pole of the battery).
A
B
C
Page 9 of 10
Quick Guide
Electronic Cylinder
6.2
Low-power opening
Using the service device CX6510, key adapter cable CX6540 and service key CX6530, the
electronic cylinder CX 6110 can be powered externally. Hence, the CX 6110 can be opened even
if the batteries are spent.
Important:
Always ensure that the battery in the service unit is full.
1.
Connect key adapter with service device and
cylinder.
2.
Execute the menu item
Service opening /
ESC Low power opening
in the service unit.
3.
When prompted, hold the service key to the
front side of the service unit.
4.
The electronic cylinder connects; the closing
sequence can be performed.
Page 10 of 10
Quick Guide
Electronic Cylinder
7
Technical data
Product designation
Clex prime electronic cylinder
Product number
CX6110
Dimensions
Dimension of the cylinder for Europrofil locks conforming to DIN
18252
Cylinder lengths
From 26/35 mm or 30/30 mm to 70/70 mm in 5-mm steps
Length of the knob
40.0 mm
Diameter of the knob
40.0 mm
Power supply
Battery, 2 pieces, Type CR2 Lithium 3 V
Battery life cycle
Up to 50,000 operations or up to 4 years of product life in
installed state without operations
Low-Power-opening
Always possible with the Clex service device
Operating temperature
-20 °C to +65 °C
Storage temperature
-20 °C to +65 °C
Installation location
Internal and building locking doors (knob inside the building area),
depending on the product version
Standards
DIN EN 50081-1 – Issue: 1993-03
DIN EN 50082-2 – Issue: 1997-11
RL 2004/108/EG