Full Text Searchable PDF User Manual
Statement of Responsibilities
This document is for use by experienced and trained Qualified Cleveland Range, LLC Authorized Service
Representatives who are familiar with both the safety procedures, and equipment they service.
Cleveland Range, LLC assumes no liability for any death, injury, equipment damage, or property damage
resulting from use of, improper use of, or failure to use the information contained in this document.
Cleveland Range, LLC has made every effort to provide accurate information in this document, but
cannot guarantee that this document does not contain unintentional errors and omissions.
The information in this document may be subject to technical and technological changes, revisions, or
updates.
Cleveland Range, LLC assumes no liability or responsibility regarding errata, changes, revisions, or
updates.
Qualified Cleveland Range, LLC Authorized Service Representatives are obligated to follow industry
standard safety procedures, including, but not limited to, OSHA regulations, and disconnect / lock out /
tag out procedures for all utilities including steam, and disconnect / lock out / tag out procedures for gas,
electric, and steam powered equipment and / or appliances
All utilities (gas, electric, water and steam) should be turned OFF to the equipment and locked out of
operation according to OSHA approved practices during any servicing of Cleveland Range equipment
Qualified Cleveland Range, LLC Authorized Service Representatives are obligated to maintain up-to-date
knowledge, skills, materials and equipment.
Cleveland Range, LLC
1333 East 179th St., Cleveland, Ohio, U.S.A. 44110
Ph: 1-216-481-4900 Fx: 1-216-481-3782 Visit our Web Site at
www.clevelandrange.com
CLEVELAND RANGE
SEQUENCE OF OPERATIONS
Steam Coil Boiler Base
1. To turn the unit on, depress the red on/off rocker switch.
x
115 VAC is sent to the upper cabinets and terminal block in control box.
x
115 VAC is sent to normally open drain valve closing it.
x
115 VAC is sent to L1 and L2 of the water level board.
2. With the water level board energized and no water in the boiler
x
115 VAC is sent from the WF terminal to the fill solenoid.
x
The fill solenoid opens and the boiler fills through the drain valve.
x
The water fills to the low probe shorting it to ground
x
115 VAC is sent from the HTR terminal through the normally closed contacts of the
highlimit pressure switch to contacts of the ice cube relay and the amber reset switch,
energizing the amber light.
3. When the momentary amber switch is depressed 115 VAC is sent to the coil of the ice cube
relay closing it.
x
The relay latches itself through a jumper to the coil.
x
If either the high-pressure switch or the low water cut off float switch opens, the
latch circuit opens.
x
When the contacts close the amber light will energize and the process may begin
again.
x
The relay contacts close sending 115 VAC through the normally closed contacts of the
operating pressure switch to the coil of the supply steam solenoid. .
4. With 115 VAC to the coil of the supply steam solenoid.
x
The solenoid opens.
x
Steam is sent to the coil in the boiler.
5. The water in the boiler is heated to steam.
x
As steam is generated and pressure builds the air is pushed out through the steamtrap.
x
When steam goes through the steam trap and heats it to 192 degrees it closes.
6. Pressure builds in the boiler to the set point .
x
The operating pressure switch opens and the heat circuit is de-energized.
x
When the pressure drops below the set point the heat circuit is energized and the heat
process begins again.
7. Water continues to fill until the high probe is grounded.
x
When the high probe is grounded the WF terminal on the water level board is de-
energized.
x
The fill solenoid closes until the high probe is ungrounded for 05 seconds.
x
If the water level drops below the high probe for more than 20 seconds the WF
terminal is energized and the water fill circuit begins again.
8. When the unit is turned off, by depressing the red rocker switch,
x
115 VAC is removed from the heat circuit.
x
115 VAC is removed from the drain circuit and the normally open drain valve opens
allowing the unit to drain.
x
115 VAC is sent to the 3-minute timer.
x
The three-minute timer will energize the fill solenoid for 3 minutes while the steamer
drains.
CLEVELAND RANGE
SEQUENCE OF OPERATIONS
Steam Coil Boiler Base
With Secondary Low Water Cut Off Switch
1. To turn the unit on, depress the red on/off rocker switch.
x
115 VAC is sent to the upper cabinets and terminal block in control box.
x
115 VAC is sent to normally open drain valve closing it.
x
115 VAC is sent to L1 and L2 of the water level board.
x
115 VAC is sent to the open contacts of the low water cut-off float switch.
2. With the water level board energized and no water in the boiler
x
115 VAC is sent from the WF terminal to the fill solenoid.
x
The fill solenoid opens and the boiler fills through the drain valve.
x
The water fills to the low probe shorting it to ground
x
115 VAC is sent from the HTR terminal through the normally closed contacts of the
operating pressure switch to coil of the contactor(s).
x
The rising water also raises the float on the low water cut-off switch closing it.
x
115 VAC is sent through the normally closed contact of the high-pressure switch to the
amber reset switch, energizing the amber light.
3. When the momentary amber switch is depressed 115 VAC is sent to the ice cube relay
closing it.
x
The relay latches itself through a jumper to the coil.
x
If either the high-pressure switch or the low water cut off switch opens, the latch
circuit opens.
x
When the contact close the amber light will energize and the process may begin
again.
x
The relay contacts close sending 115 VAC to the coil of the supply steam solenoid.
4. With 115 VAC to the coil of the supply steam solenoid
x
The steam solenoid opens.
x
Supply steam is sent through the steam coil.
5. The water in the boiler is heated to steam.
x
As steam is generated and pressure builds the air is pushed out through the steamtrap.
x
When steam goes through the steam trap and heats it to 192 degrees it closes.
6. Pressure builds in the boiler to the set point .
x
The operating pressure switch opens and the heat circuit is de-energized.
x
When the pressure drops below the set point the heat circuit is energized and the heat
process begins again.
7. Water continues to fill until the high probe is grounded.
x
When the high probe is grounded the WF terminal on the water level board is de-
energized.
x
The fill solenoid closes until the high probe is ungrounded for 05 seconds.
x
If the water level drops below the high probe for more than 20 seconds the WF
terminal is energized and the water fill circuit begins again.
8. When the unit is turned off, by depressing the red rocker switch,
x
115 VAC is removed from the heat circuit.
x
115 VAC is removed from the drain circuit and the normally open drain valve opens
allowing the unit to drain.
x
115 VAC is sent to the 3-minute timer.
x
The three-minute timer will energize the fill solenoid for 3 minutes while the steamer
drains.
Replace the
on/off rocker
switch
Yes
Connect power
to steamer.
No
Is the red light on
in the power
switch?
Is there power to
the steamer?
Is there water in
the sight glass?
Yes
See
Steamer won't
fill.
No
PROBLEM:
Steam Coil Boiler
won't build
pressure
No
Boiler won't build
pressure
Is the Amber light
on in the reset
switch?
Is there 120 VAC
between
terminals L2 and
HTR on the water
board?
Is there 120 VAC
between terminals
L2 and HTR on the
water board with a
jumper between
Low and C?
Is there 120 VAC
to terminal 6 on
the latching relay?
Repair
or Replace the
probe circuit.
Replace the
water board
Replace the
Reset switch
Yes
After depressing
the reset switch,
does the Amber
light go off?
Does this boiler
have the optional
Secondary Low
Water Cut Out?
With the High
Limit pressure
switch
temporarily
bypassed, does
the Amber light go
off when the reset
switch is
depressed?
Yes
No
No
Yes
No
Replace
the high limit
pressure
switch
With the SLW CO
switch
temporarily
bypassed, does
the Amber light go
off with the reset
switch depressed?
No
Yes
Yes
Replace the
SLWCO switch
With a jumper
from terminal 5 to
9 on the latching
relay, does the
Amber light go out
with the reset
switch depressed?
No
No
Replace the
latching relay.
Yes
Yes
Is there 120 VAC
to the coil of the
steam solenoid?
No
Yes
Replace the
latching relay
No
Yes
Is there 120 VAC
to the coilof the
steam solenoid
with the operating
pressure switch
temporarily
bypassed?
No
Replace the
latching relay
Replace
the operating
pressure
switch
Does the Steam
solenoid open?
Yes
Is there an steam
at the steam coil?
Yes
With
Elements heating
the water, the
Boiler is making
steam. Check for
leaks.
Is there a lot of
steam coming out
the drain?
Replace the
steam trap for
the boiler.
No
Supply steam
to the steamer.
No
Replace the
steam solenoid
No
No
Yes
Yes
Is the steam trap
for Incoming
steam opening to
remove air and
water from coil?
Yes
Yes
Yes
Replace the
steam trap for
the coil
No
Boiler
won't fill.
Yes
No
No
Yes
No
Yes
Yes
No
No
Yes
No
Yes
Yes
No
No
Yes
No
No
Yes
Yes
Yes
No
PROBLEM:
Steam Coil
Boiler won't fill
Yes
Is there power to
the steamer?
Is there water to
the steamer?
Supply power
to the steamer.
Supply cold
water to the
steamer.
Replace the
on/off rocker
switch .
Is there 120 VAC
between the L1
and L2 on the
water board?
Is there
120 VAC between
L2 and W F on the
water board?
Replace the
wiring to the fill
solenoid.
Is there
120 VAC across
the coil of the fill
solenoid?
Replace the fill
solenoid
Yes
Is
water leaving the
fill solenoid?
Replace wiring
to drain
solenoid.
Does
the steamer have
the optional
intermittent
blowdown timer?
Replace the
wiring to the
intermittent
blowdown
timer .
Is
there 120 VAC
between terminals
2&3 on the timer?
Replace the
intermittent
blowdown
timer.
Is there
120 VAC across
the coil of the
drain valve?
Is water draining
from the
generator?
If water
is leaving the fill
solenoid and not
draining from the
generator where is it
going? check for
leaks..
Remove
the wire from the HI
terminal on the water
board. Is there 120
VAC between L2 and
WF?
Replace the
water board
Is there
debris on the HI
probe extension?
Replace the
wire to the Hi
probe.
Clean or
replace the
probes
extension.
Replace the
drain valve.
No
PROBLEM:
Steam Coil
Boiler Over
Pressurizes
(15# Safety
valve opens)
Boiler over
pressurizes
Does operating
pressure switch
open at proper
setting (check
service manual for
that steamer)?
Replace
operating
pressure
switch
No
Does the steam
solenoid stay open
with operating
pressure switch
open?
Yes
Replace steam
solenoid
Does the pressure
in the gauge
continue to rise
with no voltage to
contactor coil?
No
Replace the
weeper valve.
Does the 15#
safety valve open
with little or no
pressure on the
gauge after it has
been replaced?
No
Replace the
safety valve.
No
Scale is blocking the
plumbing to the gauge.
Delime the boiler.
PROBLEM:
Steam Coil Boiler Stops Producing Steam
Boiler stops
steaming
Does the amber
light in the reset
switch come on?
Is the temperature
sensitive dot
(surrounded by a
yellow circle) on
the water board
white?
Replace
the water board. It has
reached a temperature of
over 180
degrees.
Yes
No
No
Does boiler have
the optional
Secondary Low
Water Cut Out?
Yes
Are the probes
covered with
scale?
No
Delime boiler
Is high pressure
switch opening
prematurely?
Replace high
pressure switch
Replace the
water board
Yes
No
Yes
No
Will Boiler stop
making steam
with SLW CO
temporarily
bypassed?
Yes
Yes
Does SLW CO
open and close as
float is moved up
and down?
No
Install delay
timer for
SLWCO
Yes
Replace
Secondary Low
Water Cut Out
switch.
No
Yes
Replace
operating
pressure
switch.
Does steam coil
leak?
Yes
Yes
Replace steam
coil
Yes
No
PROBLEM: Steam Coil Boiler Overfills
Boiler over fills
With the HI probe
emersed in water
is there 120 VAC
between terminals
L2 and W F on the
water board.?
Replace the fill
solenoid
With a jumper
across terminals
HI and C on the
waterboard, is
there 120 VAC
between L2 and
WF?
Replace ;the
water board
Yes
The probe
circuit is open.
Check continuity of the
probe wire and
probe.
No
No
With the wire
removed from
terminal 1on the 3
minute timer, is
there 120 VAC to
the fill solenoid?
Yes
Yes
Replace 3
minute timer
No