Cleco 116 Operation & Service Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Operation & Service Manual

823067

3/02

116 & 136GL - 115 R.A. Series Right
Angle Grinders

Throttle:

Extended

Standard

Handle:

Lever

Front

Rear

Side

Exhaust Terminations:

XXX

116, 136

Grinder:

Series:

Right Angle

Wheel Type:

Model:

RPM:
115

Collet

Type 27

Type 1 Wheel

5/16

1/4

3/16

Terminations:

115

6mm

3/8

5/8-11

3/8-24

4 In.

4 1/2 In.

5 In.

Guard:

NORTH AMERICA

For additional product information visit our website at http://www.clecotools.com

EUROPE

CooperTools
P.O. Box 1410
Lexington, SC 29071

Cooper Power Tools GmbH & Co.
Postfach 30
D-73461 Westhausen

Safety Recommendations

For your safety and the safety of others, read and understand the
safety recommendations before operating any grinder.

Always wear protective equipment and clothing.

Caution: Faceshields do not provide unlimited protection against
flying particles and are not to be considered as eye protection. ANSI
Z87.1 states that separate eyewear shall be used. For additional
information on eye protection, refer to Federal OSHA Regulations,
29 CFR, Section 1910.133, Eye and Face Protection, and ANSI
Z87.1, Occupational and Educational Eye and Face Protection. This
standard is available from the American National Standards Insti-
tute, Inc., 11 West 42nd Street, New York, NY 10036.

Hearing protection is recommended in high noise areas (above 85
dBA). Close proximity of additional tools, reflective surfaces, proc-
ess noises, and resonant structures can substantially contribute to
the sound level experienced by the operator. Proper hearing conser-
vation measures, including annual audiograms and training in the
use and fit of hearing protection devices may be necessary. For
additional information on hearing protection, refer to Federal OSHA
Regulations, 29 CFR, Section 1910.95, Occupational Noise Expo-
sure, and American National Standards Institute, ANSI S12.6,
Hearing Protectors.

• Gloves and other protective clothing should be worn as
required, unless they create a greater hazard.

• Do not wear loose fitting clothing, or clothing that may
restrict movement, become entangled or in any way
interfere with the safe operation of the grinder.

Grinding or other use of this tool may produce hazardous fumes and/
or dust. To avoid adverse health effects utilize adequate ventilation
and/or a respirator. Respirators should be selected, fitted, used and
maintained in accordance with Occupational Safety and Health
Administration and other applicable regulations. Read the material
safety data sheet on any materials involved in the grinding process.

Cleco grinders are designed to operate on 90 psig (6.2 bar) max. air
pressure. If the tool is properly sized and applied, higher air pressure
is unnecessary. Excessive air pressure increases the loads and
stresses on the tool parts and may result in breakage. Installation of

202409

WARNING AND

INSTRUCTION LABEL

OVER

CAUTION

Personal hearing protection is

recommended when operating

or working near this tool.

WARNING

Impact resistant eye protection

must be worn while operating

or working near this tool.

Read Operating Instructions carefully. Follow

the Safety Recommendations for your safety

and the safety of others.

Hearing protection is recommended in high noise

areas (above 85 dBA). Close proximity of other

tools, reflective surfaces, process noises, and

resonant structures can substantially contribute

to the sound level experienced by the user.

WARNING

Repetitive work motions and/or vibration

can cause injury to hands and arms.

Use minimum hand grip force consistent with

proper control and safe operation.

Keep body and hands warm and dry.

Avoid anything that inhibits blood circulation.

Avoid continuous vibration exposure.

Keep wrists straight.

Avoid repeated bending of wrists and hands.

Do not remove this tag until

the operator of this tool has

read these safety precautions.

202101 & 869974
WARNING TAGS

Cleco

MODEL

SERIAL NO.

CAUTION

TACHOMETER

203185

CAUTION LABEL

869491

WARNING LABEL

a filter-regulator-lubricator in the air supply line is highly recom-
mended.

Before the tool is connected to air supply, check throttle for proper
operation, i.e., throttle moves freely and returns to closed position.
Being careful not to endanger adjacent personnel, clear air hose of
accumulated dust and moisture. Use protective barriers where
necessary - hot sparks can burn. Barriers also help reduce noise
levels. Before removing tool from service or changing accessories,
make sure air line is shut off and drained of air. This will prevent tool
from operating if throttle is accidently engaged. Do not use tool to
drain residual air from air line, instead use of a self-relieving valve
located near tool is highly recommended.

The speed rating and warning information on the tool should be
maintained or replaced for legibility in the event of damage.
Before installing an accessory or a grinding wheel, after all tool
repairs, and whenever a grinder is issued for use, check the free
speed of the tool with a tachometer to make sure actual free speed
at 90 psig does not exceed rated free speed stamped on tool.
Grinders in use on the job must be checked at least once every 20
hours of operation, or once a week, whichever is most frequent.
Guard (if wheel type grinder) must be securely attached to the
grinder with the bolt, nut and lockwasher in place and torqued to 300
in. lbs.

INSPECT GRINDING WHEEL OR ACCESSORY
Fragments from a grinding wheel, mounted wheel or carbide
burr that breaks or comes apart while rotating can cause
serious injury or even death. Inspect grinding wheel or accessory.
Check the maximum safe RPM marked on wheel, accessory or
package. Never use wheels or accessories rated at or below actual
tool speed. Cracked, dropped, faulty, or bent accessories are
dangerous. Suspect accessories should not be used and should be
disposed of. Look for cracks, chips, water stains, or signs of abuse
or improper storage. Causes of grinding wheel failures have been
traced to such factors as:

• Dropping, bumping, or abuse (careless handling of the

grinder)

• Improper mounting
• Imbalance
• Improper shipment or storage, or age
• Mismatched speed ratings
• Exposure to water, solvents, high humidity, freezing, and
extreme temperatures

WARNING

Impact resistant eye protection
must be worn while operating
or working near this tool.

CAUTION

Personal hearing protection is
recommended when operating
or working near this tool.

WARNING

Wear respirator where
necessary.

WARNING

Fragments from an abrasive wheel
can cause serious injury or death.
Do not operate without proper
wheel guard in place.

Safety Recommendations

Wheels or accessories known to have been subjected to any of
the conditions above can burst violently and should be de-
stroyed rather than risk their use by someone who may not
notice that they are damaged.

Do not operate 116/136 RA grinder without a wheel guard if used
with Type 1 (straight) or Type 27 (depressed center) wheels.
Guard must not be modified, and any guard damaged or bent must
be replaced. Grinder must be used such that opening in guard is
away from operator.

CHECK FLANGE
A Type 1 wheel grinder's flanges must be relieved, free
of nicks that might cause stress concentrations on the
wheel which can cause cracks. Blotters must be used
and be as large in diameter as the flanges. Diameters
of driving and outer flange must be equal and measure
at least 1/3 dia. of the wheel. If flanges are less than
1/3 dia. of wheel, do not use grinder or select proper
wheel. Spindle end nut must be tightened firmly against
outer flange to insure necessary friction against blotters
to drive wheel. Caution: Overtightening can cause
wheel breakage. Type 1 breakage can also occur if:

• Outer flange is left off
• Outer flange is reversed
• A washer is used in place of either flange
• Outer and driving flange are different diameters
• Blotters are not used
• Wheel is side loaded (Grind on periphery only!)

Check spindle and driving flange on grinders used with Type 27
(depressed center) wheels. Spindles must not be bent and threads
must be free of any damage that might keep a wheel from being
centrally mounted or seated properly against the driving flange. The
spindle end nut should be tightened to prevent wheel slippage and
satisfactorly transfer the driving torque of the spindle to the wheel
through the adapter assembly.

COLLET EQUIPPED TOOLS
The collet should be checked to assure it is in good operating
condition and is secure to the tool. Accessories should be inserted
to full depth of the collet. Avoid excessive overhang and/or
excessive down force that can result in vibration, or a bent
spindle. Possible loss or ejection of accessory can result. Collet
equipped 116/136 RA grinders are intended for use with small
carbide burrs and mounted wheels only. Do not use these tools for
Type 1 or Type 27 wheel grinding. If your application calls for a Type
1 or Type 27 wheel, consult your Cleco representative for a wheel
grinder equipped with the proper wheel guard.

BEGINNING GRINDING OPERATION
Before using or after mounting a wheel or accessory, tool must be
run for one minute in a protected enclosure to check the integrity of
the wheel or accessory. During this time or any other time, no one
should stand in front or in line of the wheel or accessory. When
starting work with a cold wheel, apply it gradually to the workpiece
until it becomes warm. Do not continue to use a grinder if:

• It is not equipped with proper wheel guard
• It starts to vibrate
• You sense changes in tool speed or an unusual increase
in noise that would indicate tool is running at excessive
speed
• You notice excessive end play in spindle
• You hear any unusual sound from grinder

RETURN THE TOOL TO THE TOOL CRIB FOR SERVICE IMME-
DIATELY!

Some individuals may be susceptible to disorders of the hands and
arms when performing tasks consisting of highly repetitive motions
and/or exposure to extended vibration. Cumulative trauma disorders
such as carpal tunnel syndrome and tendonitis may be caused or
aggravated by repetitious, forceful exertions of the hands and arms.
Vibration may contribute to a condition called Raynaud's Syndrome.
These disorders develop gradually over periods of weeks, months,
and years. It is presently unknown to what extent exposure to
vibrations or repetitive motions may contribute to the disorders.
Hereditary factors, vasculatory or circulatory problems, exposure to
cold and dampness, diet, smoking and work practices are thought to
contribute to the conditions. Tool operators should be aware of the
following warning signs and symptoms so that a problem can be
addressed before it becomes a debilitating injury.

Any user suffering prolonged symptoms of tingling, numbness,
blanching of fingers, clumsiness or weakened grip, nocturnal pain in
the hand, or any other disorder of the shoulders, arms, wrists, or
fingers is advised to consult a physician. If it is determined that the
symptoms are job related or aggravated by movements and pos-
tures dictated by the job design, it may be necessary for the employer
to take steps to prevent further occurrences. These steps might
include, but are not limited to, repositioning the workpiece or rede-
signing the workstation, reassigning workers to other jobs, rotating
jobs, changing work pace, and/or changing the type of tool used so
as to minimize stress on the operator. Some tasks may require more
than one type of tool to obtain the optimum operator/tool/task
relationship.

The proper selection of the correct type of grinder is an important
ergonomic consideration. Each application should be carefully con-
sidered and the tool chosen that will minimize the stresses on the
operator that can lead to the onset of cumulative trauma disorders.
Some tasks require more than one type of tool to obtain the optimum
operator/tool/task relationship. Cleco has a complete selection of
tools including vertical, straight, angle, and extended grinders that
make possible the correct ergonomic match of the operator, tool,
and task.

1/3 Dia.

of wheel

Relieved Flange

TYPE 1

Repetitive work motions and/or vibration
may cause injury to hands and arms.

Use minimum hand grip force consistent
with proper control and safe operation.
Keep body and hands warm and dry.
Avoid anything that inhibits blood circulation.
Avoid continuous vibration exposure.
Keep wrists straight.

WARNING

Avoid repeated bending of wrists and hands.

Extension

Neutral

Flexion

Radial Deviation

Neutral

Ulnar Deviation

Avoid

Safety Recommendations

The following suggestions will help reduce or moderate the effects of
repetitive work motions and/or extended vibration exposure:

• Use a minimum hand grip force consistent with proper
control and safe operation
• Keep body and hands warm and dry (cold weather is
reported to be a major factor contributing to Raynaud's
Syndrome)
• Avoid anything that inhibits blood circulation
- Smoking Tobacco (another contributing factor)
- Cold Temperatures
- Certain Drugs

• Tasks should be performed in such a manner that the
wrists are maintained in a neutral position, which is not
flexed, hyperextended, or turned side to side
• Stressful postures should be avoided - select a tool
appropriate for the job and work location
• Avoid highly repetitive movements of hands and wrists,
and continuous vibration exposure (after each period of
operation, exercise to increase blood circulation)
• Use quality accessories (the primary source of vibration
when using a grinder is an accessory that is out of

balance, out of round, untrue, or possibly any combina-

tion of all three; avoid excessive overhang of accessory
in collet)
• Use carbide burrs that are sharp, as dull burrs require
more force and effort to remove material
• Keep tool well maintained and replace worn parts (a
preventive maintanance program with scheduled inspec-
tions is highly recommended)

Work gloves with vibration reducing liners and wrist supports are
available from some manufacturers of industrial work gloves. Tool wraps
and grips are also available from a number of different manufacturers.
These gloves, wraps, and wrist supports are designed to reduce and
moderate the effects of extended vibration exposure and repetitive wrist
trauma. Since they vary widely in design, material, thickness, vibration
reduction, and wrist support qualities, it is recommended that the glove,
tool wrap, or wrist support manufacturer be consulted for items designed
for your specific application. WARNING! Proper fit of gloves is impor-
tant. Improperly fitted gloves may restrict blood flow to the fingers
and can substantially reduce grip strength.

USE QUALITY ABRASIVE WHEELS
The primary source of vibration when using a portable grinder is an
abrasive wheel that is out of balance, out of round, untrue, or possibly any
combination of all three.

The use of quality abrasive wheels which are well balanced, round, and
true is highly recommended as they have been found to significantly
reduce vibration. Some abrasive wheels lose their balance, roundness,
and trueness as they wear from use. Because of the abusive nature of
the vibration caused by out of balance, out of round, and untrue condition
of some abrasive wheels, it is felt that these wheels are more suseptible
to failure. Excessive vibration may signal eminent wheel failure. Out of
balance abrasive wheels are dangerous. Flat spotting of the abrasive

wheel, caused by grinding the wheel to a stop after the power has been
shut off can result in changes to the balance and shape of the wheel. Be
sure the grinding wheel has stopped before setting the tool down. Set the
tool in a tool rest or tool holder when not in use.

WIRE BRUSHES
If a grinder is used for wire brushing applications the same problems of
balance, roundness, and truth as experienced with abrasive wheels
prevail. Use quality wire brushes.

USE A PREVENTIVE MAINTENANCE PROGRAM
Tool abuse or poor maintenance procedures can amplify and contribute
to the vibration produced by the abrasive wheel. A preventive mainte-
nance program featuring scheduled periodic inspections and proper
maintenance is the best way to assure safety in your portable grinding
operations. A well managed program can, for example, detect such
things as speed variations due to wear, flanges or spindles that have
been damaged from abuse, or bad bearings damaged by foreign matter
or lack of lubrication. Problems such as these can affect the wheel
trueness when the grinder is running and contribute to the vibration.
Rotor blades that are worn or chipped can lock up the motor and damage
motor components. Rotor blades should be checked periodically and
replaced if they measure less than 3/16" (4.7mm) at either end.

Proper repair procedures and the use of original Cleco service parts and
bearings rather than substitutes will return the tool to factory specifica-
tions of precision and balance, and minimize vibration.

PROPER LUBRICATION
An automatic in-line filter-regulator-lubricator is recommended as it
increases tool life and keeps the tool in sustained operation. The in-line
lubricator should be regularly checked and filled with a good grade of
10W machine oil. Proper adjustment of in-line lubricator is performed by
placing a sheet of paper next to exhaust ports and holding throttle open
approximately 30 seconds. Lubricator is properly set when a light stain
of oil collects on paper. Excessive amounts of oil should be avoided.

STORAGE
In the event it becomes necessary to store tool for an extended period of
time (overnight, weekend, etc.), it should receive a generous amount of
lubrication at that time and run for several seconds to distribute oil before
disconnecting from air supply. This will reduce corrosion and displace
water that may be trapped in tool.

This information is a compilation of general safety practices obtained
from various sources available at the date of production. However, our
company does not represent that every acceptable safety practice is
offered herein, or that abnormal or unusual circumstances may not
warrant or require additional procedures. Your work may require addi-
tional specific safety procedures. Follow these procedures as required
by your company. For more information, see the latest edition of ANSI
B186.1, Safety Code for Portable Air Tools, and ANSI B7.1, Safety
Requirements for the Use, Care, and Protection of Abrasive Wheels,
available from the American National Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.

Replace if 3/16"
(4.7mm) or less
at either end.

Type 1
Driving
Flange

Wheel Blotters
Both Sides

Wheel Guard

Spindle
End Nut

4" TYPE 1 WHEEL with 3/8" Hole

4" TYPE 27 WHEEL with 3/8" Hole

Spindle
End Nut

Driving
Flange

Wheel
Blotter

Wheel Guard

Spacer(s) 864159

Wheel Thickness No. Required

1/8"

3/16"

1/4"

None

4-1/2" TYPE 27 WHEEL with 7/8" Hole

Spindle
End Nut

Driving
Flange

Wheel
Blotter

Wheel Guard

CONTOUR SANDING PAD

Pad Nut

Spindle
Adapter

5" Rubber
Pad

100mm TYPE 27 WHEEL with 16mm Hole

Spindle
End Nut

Driving
Flange

Wheel
Blotter

Wheel Guard

Relieved Flanges
1/3 Dia. of Wheel
Flange Dias. Equal
Clean, no nicks
or burrs

116 & 136GL- 115 R.A.

RIGHT ANGLE GRINDER AND

SANDER EQUIPMENT

TOOL

APPLICATION

4" Type 27

with 3/8" Hole

4- 1/2" Type 27

with 7/8" Hole

4- 1/2" Type 27

with 5/8" Thread

100mm Type 27

with

16mm Hole

4" Type 1 with

3/8" Hole

SPINDLE

3/8- 24

5/8- 11

3/8- 24

DRIVING

FLANGE

869496

202062

843846

203138

202223

OUTER

FLANGE

not applicable

865991

NUT

843422

202061

not applicable

203139

203409

WRENCH

849834
849844

849844
843356

849844

849834
843356

849837
849844

GUARD

889208

202063

203142

889208

TOOL

APPLICATION

5" Sanding Pad

SPINDLE

ADAPTER

3/8"- 24 to 5/8"- 11

869495

PAD

849848

PAD NUT

849259

WRENCH

849834

OPERATING INSTRUCTIONS

READ SAFETY RECOMMENDATIONS BEFORE
CONNECTING TOOL.

The 116 and 136 Series Right Angle Grinders are designed
to operate on 90 psig (6.2 bar) maximum air pressure, using
a 1/4" hose up to 8' in length for the 116 and a 5/16" hose for
the 136. If additional length is required, the next larger hose
size may be connected to the 8' whip hose.

LUBRICATION
An automatic in-line filter-lubricator is recommended as it
increases tool life and keeps the tool in sustained operation.
The in-line lubricator should be regularly checked and filled
with a good grade of 10W machine oil. Proper adjustment of
the in-line lubricator is performed by placing a sheet of paper
next to the exhaust ports and holding the throttle open
approximately 30 seconds. The lubricator is properly set
when a light stain of oil collects on the paper. Excessive
amounts of oil should be avoided. Application of the tool
should govern how frequently it is greased. It is recom-
mended that the right angle gears receive a generous
amount of NLGI 2-EP grease through the grease fittings
after 40 hours of operation.

STORAGE
In the event that it becomes necessary to store the tool for
an extended period of time (overnight, weekend, etc.), it
should receive a generous amount of lubrication at that time
and again when returned to service. The tool should be
stored in a clean and dry environment.

SERVICE INSTRUCTIONS

DISASSEMBLY
To disassemble the tool, unscrew the right angle head (left
hand threads). This will allow the removal of the motor unit
from the backhead.

To remove the pinion gear, No. 863893, insert a 3/16" Allen
wrench into the rotor. Hold the Allen wrench in a vise and
unscrew the pinion gear. Use a suitable driver to drive the
front rotor shaft out of the front rotor bearing. After removing
the cylinder and rotor blades, the rear rotor shaft may be
driven out of the rear rotor bearing.

To disassemble the right angle head, unscrew the spindle
bearing cap. This will permit the removal of the spindle
assembly. Remove the two wavy washers from the head.
Remove the upper spindle bearing, the retainer ring, and the
gear spacer from the spindle. Use a suitable gear puller and
remove the gear from the spindle and press the bearing off
the spindle, if necessary.

REASSEMBLY
The tool is reassembled in the reverse order of disassembly.
Wash all parts in a solvent and inspect for damage or wear.

It is recommended when replacing worn gears in the angle
head, that both gears be replaced. Do not attempt to mix
worn gears with new gears as it will only result in short gear
life. 881789 is the gear set. It is recommended that new rotor
blades be installed at each repair cycle. If not replaced, the
used ones must measure a minimum of 3/16" (4.7mm) at
both ends.

Replace bearings that are rough or have excessive end play.

Install the front rotor bearing in the front bearing plate and
measure the distance from the face of the bearing plate to
the inner race of the bearing with the bearing race loaded
rearward. Select or fit by sanding a rotor collar .001" (.025mm)
to .002" (.050mm) longer than this measurement. Install the
rotor blades, cylinder, rear bearing plate and rear bearing on
the rotor. After final assembly of the motor unit, the cylinder
should be held securely but not tightly between the two (2)
plates. The rotor should not rub either plate.

Insert the motor unit into the backhead and screw on the
EMPTY right angle head (left hand threads). NOTE: When
installing a motor into a rear exhaust backhead, the steel ball
located in the front plate must line up with the groove in the
backhead. Head positioning spacers are used to position the
right angle head in relationship to the throttle lever. Each
.005" added or subtracted will change the location of the
head approximately 30 degrees. This must be done prior to
setting the pinion height.

Measure the distance from the end of the pinion gear to the
opposite wall of the 1 3/8" bore in the right angle head. Add
pinion spacers to bring this dimension up to 1.120/1.124"
(28.448/28.550mm). Next, drive the lower spindle bearing
on the spindle (assemble all bearings by pressing or driving
on the inner race only). Insert the key in the spindle and press
on the gear. Assemble the gear spacer and retainer ring to
the spindle and press on the upper spindle bearing. Unscrew
the empty right angle head (left hand threads) and insert the
two wavy washers and the spindle assembly. Screw on
bearing cap without the bearing cap spacers. Screw the
exhaust deflector and the assembled right angle head on the
backhead. Adjust the bearing cap (this moves the gear up
and down) until the backlash is very small but still noticeable.
The gear mesh may be adjusted in this manner while running
the tool to obtain quiet running engagement. Gauge the
space beneath the cap and select and equivalent thickness
of the bearing cap spacers. Apply grade 271 Loctite to the
clean threads on the bearing cap and tighten to 75ft./lbs.
(101.7Nm) minimum against the spacers. After reassembly,
place a few drops of 10W machine oil in the air inlet before
installing the hose. This will ensure positive lubrication of all
motor parts as soon as the air is applied. CAUTION: After the
grinder is reassembled, be sure to check the free speed
(R.P.M.) for proper speed with a dependable tachometer
before returning the grinder to service.

Replace if 3/16"
(4.7mm) or less
at either end.

3/8- 24 863895
5/8- 11 204370

864120

Collet
Size Part No.
3/16"   865423
6mm   847811
1/4"    847811
5/16"   865501
3/8"

847805

847803

863898

844320

(Side Exhaust Only)

Side Exhaust
Type Tool

Part No.

Type 1 & 27

202243

Collet

202244

Front Exhaust
Type Tool Part No.
Type 1 & 27

202207

Collet

202208

Muffler
Model Part No.
116 202338
136 869452

847234

202464

RUBBER GRIP

SLEEVE

ONLY

881393

SUPPORT

HANDLE &

RUBBER

GRIP SLEEVE

Wrenches

Size

Part No.

9/16" x 11/16" 849837
5/8" x 3/4" 849844

881789

Pinion Spacer
Size    Part No.
.005"   864732
.010"   869561
.020"   869562

842086

863925

863892

863894

847810

Bearing Cap Spacer
Size

Part No.

.003"

864499

.010"

863897

202242

869491

844829

881789

Housing Spacer
Size

Part No.

.005"

863926

.010" 869559
.020"

869560

849834

OPTIONAL

PINION GEAR

GAGE

889286

843356

202207
202208
202242
202243
202244
202338
202464
204370
842086
843356
844320
844829
847234
847803
847805
847810
847811
849834
863892

* Number of Spacers Required is Variable

Front Exhaust Deflector
Front Exhaust Deflector
Bearing Cap (incl. 869491)
Side Exhaust Deflector
Side Exhaust Deflector
Muffler
Rubber Grip Sleeve
5/81 Spindle
Gear Key
5/16" Hex Wrench
"O"-Ring 1/6" X 1-5/16"
Gear Spac er
"O"-Ring 1-1/8'' X 1-1/4"
Nose Piece
3/8" Collet (Opt.)
Upper Spindle Bearing
1/4" Collet (Std.) 6mm (Opt.)
Spanner Wrench Type 27
Lower Spindle Bearing

863894
863895
863897
863898
863925
863926
864120
864499
864732
865423
865501
869452
869491
869559
869560
869561
869562
881393
881789
889286

Retainer Ring
3/84 Spindle
Bearing Cap Spacer (.010")
Right Angle Housing
Wavy Washer
Housing Spacer (.005")
Collet Spindle
Bearing Cap Spacer (.003")
Pinion Spacer (.005")
3/16" Collet (Opt.)
5/16" Coilet (Opt.)
Muffler
Warning Plate
Housing Spacer (.010")
Housing Spacer (.020")
Pinion Spacer (.010")
Pinion Spacer (.020")
Support Handle (incl. 202464)
Gear Set (Pinion & Driven Gear)
Pinion Gear Gage (Opt.)

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

1
1

1
2

*
*

1
1
1
1

*
*
*
*

1
1
1

Part No.

Name of Part

Qty.

116 & 136GL - 115 RIGHT ANGLE HEADS

202294
202285
812165
847518
847525

847528

864489
864493
865417

116 & 136GL 15 RIGHT ANGLE MOTOR

Part No.

Name of Part

Qty.

Front Bearing Plate
Rear Bearing Plate
Cylinder Pin
Front Bearing Plate
Rotor Collar .124"
Front Rotor Bearing
Rotor Collar .122"
Rotor Collar .126"
Rotor Collar .128"

1
1
2
1

*
*
*

4
1
4
1
1
1
1
1

* Only one rotor collar required.

Rotor Blade
Rear Rotor Bearing
Rotor Blade
Cylinder (includes one (1) pin)
Cylinder (includes one (1) pin) Rear
Bearing Plate
Rotor
Rotor

867816
869445
869449
869450
869451
869638
869780
869781

869445

812165

847528

812165

Rotor Blade

Model Part No.

116 867816
136 869449

Front Bearing Plate
Type Exhaust Part No.

Front

847518

Rear

202294

Rear Bearing Plate
Type Exhaust

Part No.

Front 869638
Rear

202285

Cylinder
Model Part No.
116

869450

136 869451

Rotor

Model Part No.

116 869780
136 869781

OPTIONAL ROTOR COLLAR

PART NO.

SIZE

864487

.120

864488

.121

864489

.122

864490

.123

847525

.124

864492

.125

864493

.126

865416

.127

865417

.128

202076

.129

202187

.130

202188

.131

Inlet Screen
"O"-Ring 7/16" X 5/8"
Toggle Pin
Throttle Pin Bushing
"O"-Ring 5/8" X 3/4"
Throttle Valve Spring
Throttle Lever Pin
"O"-Ring 9/16" X 11/16"
"O"-Ring 1/4" X 1/8"
Throttle Valve
"O"-Ring 5/64" X 13/64"
Exhaust Deflector
Throttle Valve Seat
Muffler Felt
Toggle Spring

202103
202104
202105
202106
202107
202110
202217
202221
202287
202288
203043
204145
204205
833188

The lock-off lever can be purchased as a subassembly using part no. 861992.

116 & 136GL 15 RIGHT ANGLE HANDLES

845409

869855

847808

ALL MODELS

847767

203043

869489

869845

844309

863880

202288

869850

863454

869844

202287

833188

833300

202104

Front/Side Exhaust

Backhead

Model No. Part No.
116G-115A 202107
136G-115A 202110

869712

846664

FRONT/SIDE EXHAUST MODELS

REAR EXHAUST MODEL

202105

202106

Rear Exhaust
136A-C

202221

136A

202217

136A-W

202217

Rear Exhaust
Extended Backhead
136A-C 204145
136A

204144

847272

202103

Model No.

116GL- 115A

Part No.

861991

Model No.

136GLR15A-C

136GL15A

136GLR15A-W

136GLRE15A-C

136GLRE15A

Part No.

861131
861995
861135
201627
201651

COMPLETE HANDLE - SUBASSEMBLIES

Inlet Bushing
Throttle Valve Pin

(incl. 869712)

Toggle
Lock-off Lever
Backhead (incl. 846664)
Backhead (incl. 846664)
Backhead (incl. 846664)
Backhead (incl. 846664)
Inlet Bushing (833300)
Throttle Valve
Inlet Screen
Backhead (incl. 846664)
Backhead (incl. 846664)
Throttle Valve Spring

833300
844309
845409
846664
847272
847767
847808
863454
863880
869489
869712
869844
869845
869850
869855

1
1
1
1
1
1
1
1
1
1
1
1
1
1

1
1
1
1
1
1
1
1
1
1
1
1
1
2
1

Part No.

Name of Part

Qty.

NOTES

CooperTools
670 Industrial Drive
Lexington, SC 29072
Phone: (803) 359-1200
Fax: (803) 359-2013
www.clecotools.com

Ask a Question ?