Clearwater Spas K1000 Manual - User Manual

Mode and function selection wheels, all-on or all-off one
touch activation key of last used settings, interactive
display icons and on-screen reminders and messages
make for a unique user interface� Control and get
direct feedback and seamless interaction with your spa
equipment

Larger, faster, and cooler touch screen display

Driven by a powerful 400 MHz processor, the k1000
keypad features an eye-catching 4�3 inch 256K color
LCD capacitive touchscreen display resting within a thin
and beautiful enclosure that houses its cutting-edge
electronics� The in�k1000 keypad fits perfectly on
the edge of any spa�

Keypad functions

Power

Touch the screen to turn on the keypad� 3 minutes after
the last pump is turned off, the screen will shut off if there
is no touch activity�

Then follow the instructions on the screen to access the
main screen�

Main screen

The main screen gives you access to your accessories
and water temperature� At the bottom of the screen
you will see any error or maintenance messages that
are present�

in.k1000 keypad layout

all-on or all-off key

(one touch activation)

direct to function

selection wheel

(settings and

additional options)

on-screen

system messages

and reminders

interactive display icons

(main spa functions)

mode selection

wheel (settings and

accessories)

Start or stop accessories

To start or stop an accessory, touch the associated icon�
Icons will become animated when their accessory is
turned on, and animation will stop when turned off�
Icons on the screen will reflect the speed or state of
the devices running on your spa� When an accessory has
more than two speeds press the button until it reaches
the desired speed�

Notifications

A notification area at the top right-hand side of the screen
shows the state of certain accessories installed in the spa�

Keypad functions

Notification icons

in.touch:

• Indicates that the in�touch module is detected

and connected to a Wi-Fi network�

• A red cross indicates that the in�touch module

is detected but isn't connected to a Wi-Fi network�

• An animated icon indicates that the in�touch

module is connecting to a Wi-Fi network�

For more information about the in�touch,
refer to the Wi-Fi section�

in.clear:

• The icon is green when the in�clear is

generating bromine�

• The icon is grey when the in�clear isn't

generating bromine�

• A red cross indicates that the in�clear is

turned off�

For more information about the in�clear,
refer to the in�clear functions section�

in.stream 2:

• The icon is green when the in�stream 2 is on�
• The icon is grey when the in�stream 2 is off�

For more information about the in�stream 2,
refer to the in�stream 2 functions section�

Water temperature

The temperature shown at the bottom of the screen shows
the current water temperature� Use the Up and Down
icon to set the desired temperature� The set point will
appear in blue� After 3 seconds without any change to the
set temperature value, the current water temperature will
reappear�

When the set value is lower than the current temperature
Cooling to xx�x will appear below� When the set value is
higher than the current temperature, Heating to xx�x will
be indicated under the value� Normally there is a short
delay before the heating starts, during which Heating
Suspended is indicated under the value�

Spa menu

From the home page you can access the following:
•

in�clear (if installed)

•

in�stream 2 (if installed)

•

spa menu

•

settings

To select an option, slide the left wheel up or down until
the desired icon menu is highlighted in the middle�

On the right side is a menu for access to the Display and
Contrast pages�

Keypad functions

Display page

Use this page to change the display orientation�

Contrast page

Use this page to change the display contrast�

Settings

In the Settings page you can access the following:
•

WaterCare

•

Maintenance

• Date & Time

•

Keypad

•

Electrical Config

•

Wi-Fi

•

About

To select an item, slide the right wheel until the desired
icon is highlighted in the middle or press on the menu
name�

Keypad functions

Water care

The Water Care page will help you set up your ideal
filtration and heating settings� Choose between

Away from

Home, Beginner, Energy Savings, Super Energy

and

Weekender,

depending on your need� Touch the Water

care name to choose your setting� A green checkmark will
appear on the selected icon to confirm your choice �

In Economy mode, the set point will be reduced by 20°F*,
which means that the heating system will not be engaged
unless the temperature falls to 20°F below the spa's set
temperature�

The filtration schedule shown on the screen will apply to
the main filtration pump, most likely pump 1� If your spa
uses a circulation pump configured to run 24 hours, the
screen will show you the purge setting instead of filtration�
The purges are pre-programmed for a fixed number of
minutes, therefore the duration will be set to N/A on the
screen, and only the start time can be modified�

* Default pack value

Water care modes

Away:

In this mode the spa will always be in economy;
the set point will be reduced by 20° F�

Beginner:

The spa will never be in economy mode and will be
filtering according to the pack's low level configuration�

Energy Savings:

The spa will be in economy mode during the peak hours
of the day and resume normal mode on the weekend�

Super Energy Savings:

The spa will always be in economy mode during peak
hours, every day of the week�

Weekender:

The spa will be in economy mode from Monday
to Friday, and will run normally on the weekend�

Keypad functions

Modifying schedules

To modify a Water Care category, touch the pen icon at
the right end of the desired watercare to open the selected
Water Care menu�

Touch the Economy tab to change the economy setting
and filter cycle tab for the filtration settings (or schedules)�
You can add economy or filtration schedules by touching
the « + » symbol �

To delete a schedule, touch the garbage can icon at the
right end of the desired line�

You can modify the programmed schedules by selecting
one and adjusting the schedule�

You have several possibilities for the schedule (Mon-Fri,
weekend, every day, or single days)� The schedules will
be repeated every week� The time and duration are set in
30 minute increments� Once you have set the schedule,
use the calendar icon to go back� Ensure that you have
selected the desired Water Care mode in the main Water
Care menu�

Maintenance

From the Maintenance page you can access the following:

• Error log

To acces the desired option simply touch the desired
menu item�

Error Log

In this section you can see errors that have been archived
by the system� Drag the list Up and Down to move through
the list� Errors are archived chronologically, from the most
recent at the top to the oldest at the bottom�

The Error log page shows the error code, the date
of the error, and the time� Touching the garbage can icon
will delete the Error log (with a confirmation)�

For more information, see the Error messages section�

Keypad functions

Date and time

Simply touch the item you want to change�

Set date

Here you can adjust the year, month and day�

Simply swipe up and down the column you want to
change, and select the desired value� When done,
touch the calendar icon at the right of the screen�

Set time

Here you can change the hour, minute and time format�

Simply swipe up and down the column you want to
change, and select the desired value� When done,
touch the calendar icon at the right of the screen�

Keypad settings

Here you can adjust the Temperature Units, Day/Night
contrast, and Display orientation and language�

Simply touch the item you want to change�

Temperature units

Choose the appropriate units to display temperatures�

Display page

Use this page to change the display orientation�

Keypad functions

Electrical configuration

Please do not make changes in this section unless you
are a qualified electrician.

In this section you can change the low-level configuration,
as well as modify the number of phases and the input
current�

Please note that if there are two spa packs in the system
(i�e� a SwimSpa installation), the master unit’s chosen
configuration must support a slave unit� If, after re-booting,
the chosen configuration does not support SwimSpa
installations, the in�k1000 will return (after about
45 seconds) to this configuration menu and prompt the
user to select a configuration number again�

Contrast page

Simply touch the item you want to change�

Language Select

Use this page to select the display language of the
in�k1000 keypad�

Keypad functions

About

This section shows information about the in�k1000
software number, and the revision numbers of the
different components of your system�

Wi-Fi

This menu is present if the in�touch module is present�
This page allows you to connect your in�touch module to a
Wi-Fi network or to change its network�

For more details about other in�touch connection methods
please see the in�touch techbook�

After a few seconds the available networks will appear on
the screen, as well as their signal strength�

Swipe Up or Down the list to select your network�
If the Wi-Fi network is password protected enter it when
prompted� Use Enter to validate the password�

If no password is required the in�touch will connect
automatically�

Once the in�touch module is connected to a
Wi-Fi network a green check mark will appear in
the Wi-Fi menu, and the network name will appear
in the

Settings

menu�

Keypad functions

Wipe screen

This message appears when too much water is detected
on the touch screen� Simply wipe away excess water�

in.stream 2 functions

This menu is available only if the in�stream 2 audio station
is detected in the spa accessories�

The audio page will allow you to control the active audio
source� Note that only the functions that apply to the
selected source will be available� From this page, you can
also access the following:

• in.stream 2 on/off

• speaker settings

• audio source selection

• disconnect bluetooth

To select an item, slide the right wheel until the desired
icon is highlighted in the middle�

For more information about the in�stream 2 audio station,
please refer to the in�stream 2 techbook�

Power

To turn the in�stream 2 on or off, tap the icon located in
the center of the screen�

Keypad functions

Speakers Settings

Move the sliders to adjust the Balance, Fader and
subwoofer settings�

The Fader and Subwoofer sliders will only appear in the
Speaker menu if the corresponding speakers are installed
on the in�stream 2�

Source Menu

To change the audio source, simply tap on the desired one�

Note that only the sources installed on the in�stream 2 will
be displayed in the source menu�

Disconnect Bluetooth

If a device with Bluetooth technology is connected to
the in�stream 2, you can disconnect it by pressing the
Disconnect button at the bottom of the screen�

Doing so will also prevent the in�stream 2 from
automatically reconnecting to this specific device until it
has been reconnected using the device itself�

in.clear functions

This menu is available only if the in�clear is detected in the
spa accessories�

The k1000 keypad can be used with the in�clear
sanitation system�

The

in.clear

menu allows you to configure your

maintenance settings and boost levels� The main

in.clear

menu shows the current status of the sanitation system,
whether it's on, and if it's generating bromine or not�

For more information about the in�clear, bromine levels,
and other settings, please refer to the in�clear user manual�

Keypad functions

in.clear on/off

Use the On/Off submenu to turn on or off the in�clear
sanitation system�

Bromicharge

™

level

The Bromicharge page allows you to see the current level
of sodium bromide in the water� Ideally, you should aim to
be near the center of the green area of the gauge�
Follow the instructions given on the screen to increase or
reduce the level�

Note that it may take a few moments to obtain a reading
from the in�clear, during which time the wait icon is
displayed on the gauge�

There are no settings to change on this page,
it is informative only�

Modify the Boost level

The Boost level is used to set amount of boost required�
As a rule, enter the number of bathers in the bath�
Boost mode is automatically activated 5 minutes after
starting a pump�

Modify the maintenance level

The maintenance level can be changed, and must be
tested with a bromine level tester� The tester should report
between 3-5 ppm� If the bromine level is within this range
for 3 consecutive days, your maintenance level is correctly
adjusted� If you adjust the Maintenance level by more
than 2, you will be asked to confirm this�

Code

Message

High Limit circuit has tripped!

FLO

No Flow condition for more than 2 hours

FLO

No Flow condition

A hardware error was detected (Relay stuck)

Spa temperature is too high

Temp probes or detection circuit are defective

AOH

Elevated internal temperature

FLC

The pressure switch is closed

SP in

Input voltage issue

RH NC

Comm� error between in�xm2 - in�therm

RH ID

in�xm2 and in�therm incompatible

SC ER

Error detected during the learning mode

in�xm2 Fuse # 1 is blown

in�xm2 Fuse # 2 is blown

in�xm2 Fuse # 3 is blown

ER1

SwimSpa config� : slave unit is missing

Hardware error was detected (Thermal fuse)

UPL

The spa pack does not have valid software�
Please insert valid in�stick to reprogram spa pack�

CFLO

No Flow condition

HIBr

Add fresh water to the spa

HiBr

Add fresh water to the spa

LoBr

Add BromiCharge to spa water

NoBr

Add BromiCharge to spa water

Comm

Verify cable connections

Supp

Connect power cord to 240 V source

The list below shows the different error messages that can appear on the home screen�

Refer to the troubleshooting and error codes section of the TechBook for your spa pack system�

Please note that if you are in a swim spa configuration, the message may be followed by "Master" or "Slave" to designate
from which pack the error is coming from�

Error messages

Keypad functions

Earliest support

Power

5�00

Main screen

5�00

Start or stop accessories

5�00

Notifications

5�00

Water temperature

5�00

Spa menu

5�00

Settings

5�00

Water care

5�00

Water care modes

5�00

Modifying schedules

5�00

Maintenance

Error log

5�00

Date and time

Set date

5�00

Set time

5�00

Keypad settings

Temperature unit

5�00

Display

5�00

Contrast

5�00

Language

English

5�00

Français

5�00

Español

5�00

Polski

5�00

Nederlands

5�00

Deutsch

5�00

Norsk

5�00

Svenska

5�00

Magyar

5�00

Italiano

5�00

Português

5�00

Electrical configuration

5�00

Wi-Fi

5�00

About

5�00

Wipe screen

6�00

in�stream 2 functions

5�00

in�clear functions

7�00

Support for AC Light output

8�00

Support for in�xe-2 and in�ye-2 packs

8�00

Feature matrix

The following table presents the features and/or options available for the in�k1000 keypad, and the earliest software version
at which this feature/option is available� All versions greater than the earliest version continue to support the feature�

Specifications

Specifications are subject to change without prior notice.

Part number

0607-005024

Model

IN�K1000-BK-GE1

Environmental

Operating temperature:

-4°F (-20°C) to 149°F (65°C)

Storage temperature:

-22°F (-30°C) to 185°F (85°C)

Water ingress protection:

IPX5

Mechanical

Weight:

1�05 lbs (0�48 kg)

Dimensions (W x H x D):

7,49" x 5,17" x 1,93"
(190 mm x 1031 mm x 49 mm)

Audio specifications

Audio source supported:

in�stream 2

Compatibility

in�yt, in�ye, in�yj, in�xe, or in�xm2 spa packs with appropriate software revision

in.k1000

full-featured color capacitive

touchscreen display keypad for spas

TechBook

Fun, simple, engaging

Truly interactive control

Larger, faster and cooler

K1000 manual 03.11.19

Ask a Question ?