Clearaudio statement phono User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

User manual

© clearaudio electronic GmbH, 2017/11

Made in Germany

statement phono

Dear Clearaudio-customer,

Thank you for choosing the

statement phono

preamplifier, a high quality product made in Germany

by Clearaudio.

To avoid misuse and achieve the best possible results with your

statement phono

preamplifier, ple

ase read the instruction and user manual carefully.

The design of the Clearaudio

statement phono

preamplifier revolutionizes the reproduction of vinyl

records to a standard barely imaginable.

The fully symmetrical circuit topology of the statement phono preamplifier together with the ability

to use either RIAA, or almost any other phono equalization curve makes the

statement phono

pre-

amplifier one of the most flexible and sophisticated phono preamplifiers in the entire audio world.

Hand selected and matched electronic parts such as extremely low noise resistors and non-magnetic

silver-glimmer capacitors contribute towards the phenomenal performance.

Fully symmetrical analogue circuit

Extremely low noise resistors and non-magnetic silver-glimmer capacitors

Remote control input load adjustment

RIAA and fully adjustable equalization curves

2 phono inputs

3 additional analogue inputs

Fully symmetrical accu power supply in separate, massive housing.

Double shielded case construction

We wish you a lot of pleasure with your new Clearaudio

statement phono

preamplifier!

Clearaudio electronic GmbH

This section must be read before any connection is made to the mains supply.

User manual

Warning

Do not expose the equipment to rain or moisture.

Do not handle the mains lead with wet hands.

No naked flame sources, such as lighted candles, should be placed on the equipment.

CE-MARKIERUNG

Copyright

Recording and playback of any material may require consent. For further information refer to the

following:

- Copyright Act 1956

- Dramatic and Musical Performers Act 1958

- Performers Protection Acts 1963 and 1972

- Any subsequent statutory enactments and orders

© clearaudio electronic GmbH, 2017/11

Contents

1. Packing overview ................................................ 4

2. Setup ................................................................... 4 - 5

3. Back view of the

statement phono

..................... 6

4. General information of the display modes .......... 7 - 10

5. Safety instructions .............................................. 10

6. Service ................................................................. 10

7. Technical specifications ...................................... 11 - 13

Warranty information .............................................. 14

User manual

Made in Germany

User manual

1. Packing overview

The Clearaudio

statement phono

is delivered in special packaging to ensure its safe transport.

Retain this original packaging for any future transportation. Please check the contents immediately

after unpacking:

•

Clearaudio

statement phono

preamplifier

•

External power supply

•

1 Power cord

•

2 Connection cords

•

User manual

•

Warranty card

•

Clearaudio

quality control card

To achieve the full performance of the

statement phono

preamplifier, please read the instruction and

user manual carefully.

The following pages will ensure the best performance and will help to avoid any misuse.

2. Set up

2.1. Placement of the

statement phono

The

statement phono

should be placed close to the turntable in order to use as short as possible

phono cables between the tonearm and the

statement phono

. The best connection between the

cartridge and the

statement phono

will be achieved with a direct-wired tonearm.

The

statement phono

should be placed as far away as possible from motors, transformers, power

amplifiers or any other source of hum-inducing magnetic fields.

2.2 Applying Power

The external power supply contains two separated power supplies, which provide four individual

supplies to each channel. Before applying power, check the voltage indication on the external power

supply is correct for the local AC power in your country. Connect both 15-pin D-Sub-connectors to

the

statement phono

and lock with the integrated screws, then connect the AC power cord and turn

on the AC power-switches on the power-supplies.

After 3-5 seconds the “Mute LED” turns off and the signal outputs are working.

Note:

Never disconnect the D-Sub connector from the

statement phono

if the power supply is still on.

Before you disconnect the D-Sub connector from the power supply or from the

statement phono

make sure, that the AC Power switch is in the OFF position! Only then you can disconnect the D-Sub

connectors.

For optimal audio performance we recommend that the statement phono is left continuously swit-

ched on stand by made to minimize thermal cycling of the components.

© clearaudio electronic GmbH, 2017/11

User manual

Made in Germany

2.3 Input and Output Connections

The quality of the interconnect cables are extremely important in realizing the full sonic potential

of the Clearaudio

statement phono

. Ideally the interconnect needs to be symmetrically designed,

not coaxial.

Inputs and outputs for left and right channels are marked accordingly on the rear panel.

If you are using the unbalanced RCA-Inputs, the ‘Input Select Switch’ must be in the “Unbalanced”

position, if using the XLR connector the switch must be set to “Balanced” it valids by balance+.

By Statement are everything other.

To achieve the best high fidelity performance you also can connect the

statement phono

directly to

your power amplifier. The automatic mute function will prevent any noise from reaching the louds

peakers if the statement phono is turned on or off while the power amplifiers are still turned on.

2.4. Minimizing Hum

Note:

You should minimize hum before listening to an LP record!

Also we recommend the use of phono cables with symmetrical design such as Clearaudio “Quint”

or “Sixstream”.

To minimize hum and other undesirable noise, if possible you should use the balanced inputs and

outputs.

Also always take care to ensure an effective ‘Ground’ connection to your turntable.

Please note:

Phonopreamplifier are devices with a high signal gain, because the voltage which is supplied by

the cartridge of the turntable is very low (in the range of a few µV). For this reason high frequency

interference signals are noticeable reinforced. A complete blocking of these interference signals in

the device would degrade the audio performance.

A result could be that high frequency interference, for example from the 230 V net or 115 V AC will

affect the sound quality.

The device should therefore not operate near to high frequency generating devices such as mobile

phones or modems or electricity networks for data transport (PLC).

3. Rear view of statement phono

User manual

Pin connections: Inputs and Outputs

XLR:

Power Supply

15-pin. D-Sub Connector:

Pin 1 = GND (Shield)

Pin 2 = Hot (+)

Pin 3 = Cold (-)

Pin 1, 9 = -18 V output class A buffer

Pin 2 = GND remote control

Pin 3, 5, 10, 13 = GND

Pin 4, 11 = -18 V phono preamps

Pin 6, 14 = +18 V phono preamps

Pin 7 = +15V remote control

Pin 8, 15 = +18 V output class A buffer

Pin 12 = remote

© clearaudio electronic GmbH, 2017/11

Pic. 1: Back view of the

statement phono

If you use a mobile phone near the

statement phono

, the audio

performance can be influenced!

User manual

Made in Germany

4. General information of display modes

The letters in the display will be highlighted in each menu step or in any location you are.

DANGER

overlimit

signal

sleep

mode

please

switch off

Input signal is too high >

please degrase phono gain

(54dB>34dB) or preampli-

fier gain (20dB>12dB)

If the unit is not in use or if

there is no music signal for 3

minutes, the unit will automati-

cally switch to stand by mode.

Any signal on chosed input will

switch on the unit automatically.

This screen appear, if the

unit leave without any

signal on chosed input

>10min. Please, switch off

the unit on power supply

MENU:

< INPUT

< control >>

< setting

< INPUT

< control

< setting >>

Turn the menu control to

choose the indicated menu

item.

Push the menu button to

select / enter.

The three main settings:

- input

- control

- setting

User manual

© clearaudio electronic GmbH, 2017/11

2100A

DO tl.PHONO1/2

< phono 2

< line 1

input

< phono 1

< line 2

< aux

2100B

DO tl.PHONO1/2

input

< aux

< phono 1

< phono 2

< line 1

< line 2

2100C

DO tl. LINE 1

< line 1

< line 2

< phono 1

< phono 2

input

< aux

2100D

DO tl. LINE 2

< line 1

< line 2

< phono 2

< phono 1

< aux

input

2100E

DO tl. AUX

input

< phono 1

< phono 2

< line 1

< line 2

< aux

Menu for set up of

phono input 1

(XLR – balanced)

Menu for set up of

phono input 2

(RCA Cinch – unbalanced)

Menu for set up of

line input 1

(XLR – balanced)

Menu for set up of

line input 2

(RCA Cinch – unbalanced)

Menu for set up of

aux input

(3,15 jack – unbalanced,

on front pael)

User manual

Made in Germany

2100F

DO tl.PHONO1/2 + EQ

input

< phono 1 EQ

< phono 2

< line 1

< line 2

< aux

Display indicates that the

“RIAA Equalization” is

switched on. Only possible

in phono 1/2 mode. For

more information please

see “RIAA Equalization”.

RIAA Equalizer (EQ) on:

+ 6 dB

- 6 dB

LOW

50 Hz

MID

6 kHz

HIGH

10 kHz

switch

on / off

RIAA curve usage described in a follow up appendix!

2100 RETURN

input

< phono 1

< phono 2

< line 1

< line 2

< aux

2200A - PRESET

fce zhasínání je NEAKTIVNÍ

ont

rol

< switching off

< overlimit warning

2200B - PRESET

fce Overlimit Warning je AKTIVNÍ

ont

rol

< display mode

< warning on

Return to “input main

menu”. Choose your input

by turning the menu but-

ton and push to confirm

By pusching “switching on/

off”. - the backround blue

screen switched off in 3

sec after any change you

make on menu per MENU

knob or RC

By pushing “warning on/

off” you can choose whe-

ther the overlimit warning

will be indicated in the

display or not. We recom-

mend that this is left “on”.

Control:

User manual

5. Safety instructions

Important!

•

Do not use the

statement phono

preamplifier if you see any damage whatever!

•

Do not recycle the equipment as domestic refuse!

Please note:

If the device is not used for a longer time, you should switch it off with the switch on

the rear panel to avoid unnecessary Standby-consumption.

6. Service

Should service be necessary: service for all Clearaudio products should only be carried out by

Clearaudio

authorized service personnel.

In case of any repair, the Clearaudio

equipment needs to be send to your nearest authorized dea

ler or distributor. Only if your dealer or distributor cannot support you please contact Clearaudio

direct:

Clearaudio electronic GmbH

Spardorfer Str. 150

91054 Erlangen

Germany

Tel/Phone: +49 9131 40300100

www.clearaudio.de

www.analogshop.de

info@clearaudio.de

To ensure secure transport, only ever ship the statement phono in the original packing!

Clearaudio can only provide the warranty if the

statement phono

is properly re-packed and ship-

ped in the original packing.

© clearaudio electronic GmbH, 2017/11

User manual

7. Technical specifications

STATEMENT High End Phono Preamplifier

Preamplifier PURE CLASS A:

Inputs:

- Phono 1

- Phono 2

- Line 1

- Line 2

- Aux

5 (4 x rear, 1 x front)

balanced XLR rear

unbalanced RCA Cinch rear

balanced XLR rear

unbalanced RCA Cinch rear

unbalanced 3,15 Jack front

Outputs:

- Switchable

- Phone

2 back

balanced XLR and unbalanced RCA

1 front

Dimensions (W/D/H in mm):

435 x 350 x 100mm

Dimensions (W/D/H in inches):

17.13 x 13.78 x 3.94 inches

Weight:

12kg

Power supply:

Fully symmetrical line accu - power supply

Main power / channel:

2 x 3 x 18V / 1A

Battery power / channel:

2 x 18 V/3.2 Ah

Power consumption:

Max. consumption: 200 watts

Consumption in operation: 50 - 100 watts

Standby mode: 0.5 watts

Off mode: 0.0 watts

Dimensions (W/D/H in mm):

435 x 350 x 100mm

Dimensions (W/D/H in inches):

17.13 x 13.78 x 3.94 inches

Weight:

22kg

Made in Germany

User manual

Technical specifications

statement phono

preamplifier:

Nominal input voltage:

0.5 mV/MC mode (+54 dB)

5 mV/MM mode (+34 dB)

Headroom:

+12dB

Input load:

8 values, switchable RC (Remote control device)

- 5R, 25R, 50R, 100R, 250R, 500R, 1k, 47k

Main gain / 1 kHz:

+54 dB MC mode

+34

mode

switchable

MPS (Menu Pre Setting)

Subsonic filter:

-24 dB/octave @ 20 Hz, switchable RC

(Remote control device)

RIAA accuracy:

+ 0.05 dB/20-100 kHz

Phono equalizer:

3 bands, +/- 6 dB, switchable RC

(Remote control device)

50 Hz, 6 kHz, 10 kHz

S/N*:

- 5 mV/1 kHz/+50 dB:

- 0.5 mV/1 kHz/+70 dB

-82 dB

-90 dB (“A” weighted)

-72 dB

-80 dB (“A” weighted)

THD +N*:

- 5 mV/1 kHz/+50 dB:

- 0.5 mV/1 kHz/+70 dB:

- total gain +50 dB:

< 0.008%

< 0.0035% (“A” weighted)

< 0.03%

< 0.015% (“A” weighted)

<0.004% /1 kHz/Vout=10 V

<0.0003% (“A” weighted) / 1 kHz/Vout=10 V

IMD*:

- 5 mV/1 kHz/+50 dB:

< 0.01%

<0.0035% (“A” weighted)

User manual

Technical specifications

statement

line preamplifier:

Nominal input voltage:

4 V/1 kHz @ +12 dB

2 V/1 kHz @ +20 dB

Nominal input impedance:

10 kΩ

Gain:

2 values, switchable MPS (Menu Pre Setting)

+12 dB

+20 dB

Nominal output impedance:

10 Ω

Nominal output voltage:

> 12 V

Minimal load:

10 Ω

Nominal output power:

2 x 10 W/10 Ω, pure class A

S/N:

- 4 V/1 kHz/+12 dB:

- 2 V/1 kHz/+20 dB:

>98 dB

>104 dB (“A” weighted)

>92 dB

>98 dB (“A” weighted)

THD +N:

- 4 V/1 kHz/+12 dB:

- 2 V/1 kHz/+20 dB:

- total gain +12 dB

< 0.004%

< 0.003% (“A” weighted)

< 0.006%

< 0.003% (“A” weighted)

<0.0008% /1kHz/Vout=10V

IMD:

- 4 V/1 kHz/+12 dB:

< 0.006%

< 0.0035% (“A” weighted)

Warranty:

5 years*

* Provided that the warranty card is correctly completed and returned to Clearaudio within 14 days of purchase.

Clearaudio electronic is not responsible for typographical errors in descriptions.

Technical specifications subject to change or improvement without prior notice.

Product availability is as long as stock lasts.

Copies and reprints of this documents, including extracts, require written consent from

Clearaudio electronic GmbH; Germany

Made in Germany

User manual

To achieve the full Clearaudio warranty (

statement phono

5 years), it is necessary that you fill out

and send the corresponding part of the warranty registration certificate /card back to

Clearaudio,

within two weeks after purchase.

Only if the product is returned in its original packing Clearaudio can provide the warranty of 5

years. Otherwise Clearaudio provides the legal warranty of 2 years.

ENGLISH

WARRANTY

For warranty information, contact your local Clearaudio distributor.

RETAIN YOUR PURCHASE RECEIPT

Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred

to as necessary for insurance purposes or when corresponding with Clearaudio.

IMPORTANT

When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. Your

purchase receipt or invoice is adequate for such proof.

FOR U.K. ONLY

This undertaking is in addition to a consumer‘s statutory rights and does not affect those rights in any way.

FRANÇAIS

GARANTIE

Pour des informations sur la garantie, contacter le distributeur local Clearaudio.

CONSERVER L‘ATTESTATION D‘ACHAT

L‘attestation d‘achat est la preuve permanente d‘un achat de valeur. La conserver en lieu sur pour s‘y reporter aux fins

d‘obtention d‘une couverture d‘assurance ou dansle cadre de correspondances avec Clearaudio.

IMPORTANT

Pour l‘obtention d‘un service couvert par la garantie, il incombe au client d‘établir la preuve de l‘achat et d‘en corroborer

la date. Le reçu ou la facture constituent des preuves suffisantes.

DEUTSCH

GARANTIE

Bei Garantiefragen wenden Sie sich bitte zunächst an Ihren

Clearaudio

Händler. Heben Sie Ihren Kaufbeleg gut auf.

WICHTIG!

Die Angaben auf Ihrer Quittung erlauben uns die Identifizierung Ihres Gerätes und belegen mit dem Kaufdatum die

Dauer Ihrer Garantie-Ansprüche. Für Serviceleistungen benötigen wir stets die Gerätenummer. Diese finden Sie auf dem

Typenschild auf der Rückseite des Gerätes oder auch in der beigefügten Garantie-Registrierkarte.

NEDERLANDS

GARANTIE

oor inlichtingen omtrent garantie dient u zich tot uw plaatselijke

Clearaudio.

UW KWITANTIE, KASSABON E.D. BEWAREN

Uw kwitantie, kassabon e.d. vormen uw bewijs van aankoop van een waardevol artikel en dienen op een veilige plaats

bewaard te worden voor evt, verwijzing bijv, in verbend met verzekering of bij correspondentie met

Clearaudio.

BELANGRIJK

Bij een evt, beroep op de garantie is het de verantwoordelijkheid van de consument een gedateerd bewijs van aankoop

te tonen. Uw kassabon of factuurzijn voldoende bewijs.

User manual

ITALIANO

GARANZIA

L’apparecchio è coperto da una garanzia di buon funzionamento della durata di un anno, o del periodo

previsto dalla legge, a partire dalla data di acquisto comprovata da un documento attestante il nominativo del

Rivenditore e la data di vendita. La garanzia sarà prestata con la sostituzione o la riparazione gratuita delle

parti difettose.Non sono coperti da garanzia difetti derivanti da uso improprio, errata installazione, manuten

zione effettuata da personale non autorizzato o, comunque, da circostanze che non possano riferirsi a difetti

di funzionamento dell’apparecchio. Sono inoltre esclusi dalla garanzia gli interventi inerenti l’installazione e

l’allacciamento agli impianti di alimentazione.

Gli apparecchi verranno riparati presso i nostri Centri di Assistenza Autorizzati. Le spese ed i rischi di trasporto

sono a carico del cliente. La casa costruttrice declina ogni responsabilità per danni diretti o indiretti provocati

dalla inosservanza delle prescrizio-ni di installazione, uso e manutenzione dettagliate nel presente manuale o

per guasti dovuti ad uso continuato a fini professionali.

ESPAÑOL

GARANTIA

Para obtener información acerca de la garantia póngase en contacto con su distribuidor Clearaudio.

GUARDE SU RECIBO DE COMPRA

Su recibo de compra es su prueba permanente de haber adquirido un aparato de valor, Este recibo deberá

guardarlo en un lugar seguro y utilizarlo como referencia cuando tenga que hacer uso del seguro o se ponga

en contacto con Clearaudio.

IMPORTANTE

Cuando solicite el servicio otorgado por la garantia el usuario tiene la responsabilidad de demonstrar cuándo

efectuó la compra. En este caso, su recibo de compra será la prueba apropiada.

Made in Germany

clearaudio electronic GmbH

Spardorfer Straße 150

91054 Erlangen

Germany

Phone/Tel.: +49 9131 40300 100

Fax:

+49 9131 40300 119

www.clearaudio.de

www.analogshop.de

info@clearaudio.de

Handmade in Germany

(Änderungen und Irrtümer vorbehalten. Für Druckfehler keine Haftung.

Lieferbar solange Vorrat reicht. -

Technical specifications are subject to change or improvement without prior notice.

Clearaudio accepts no liability for any misprints.

Product availability as long as stock lasts.)

2017

Made in Germany

Ask a Question ?