Full Text Searchable PDF User Manual
Wake & Shake
Large Display Alarm Clock
& Telephone Ring Signaler
C O M M U N I C A T I O N S
Important Safety Instructions
When using your alarm clock, always follow basic safety
precautions to reduce the risk of fire, electrical shock and injury
to persons, or property, including the following:
1. Read and understand all instructions, warnings and product
2. Be aware there is a slight possibility of electrical shock from
3. Do not use this product near or in water or when you are wet. If
the product comes in contact with any liquid, unplug the power
cord and telephone cord immediately. Do not plug the product
back in until is has dried completely.
4. Do not use liquid or aerosol sprays for cleaning.
5. If this product does not operate properly, refer to the Warranty
information on page 9 of this manual. Do not open this product
as you may expose yourself to hazardous voltages or other risks.
Opening this product automatically voids the warranty.
6.Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled on the product.
c. If the product has been exposed to rain and water.
d. If the product does not operate normally by following the operat-
ing instructions. Adjust only those controls that are covered by
the operating instructing because improper adjustment of
other controls may result in further damage.
e. If the product has been dropped or appears damaged.
f. If the product exhibits a distinct change in performance.
SAVE THESE INSTRUCTIONS
Your Wake & Shake offers you the option of using it as both an
alarm clock and a telephone ring signaler. The following diagram shows
you how to set up your Wake & Shake so you may use it for both.
NOTE: Setting up your Wake & Shake as a tele-
phone ring signaler requires the use of a dual
phone jack adapter. This is a small inexpensive
device available at your local drug or hardware
store. (See #1)
1. Plug Dual Phone Jack Adapter into wall jack.
2. Plug telephone line from your telephone into one jack on adapter.
3. Plug one side of line cord (included) into phone jack on the back of
the clock and the other into the available jack on the adapter.
4. Plug the AC power adapter into the adapter jack on the back of the
5. Plug the AC power adapter into an electrical wall outlet.
6. Plug the Bed Shaker into the jack in the back of the phone.
Now your Wake & Shake is ready for use. Simply set the time &
alarm and you are ready to go.
How To Set The Time
1. Press and hold the
2. Holding down the
button, press the
button, then the
button until the correct hour appears.
3. Release the
NOTE: There is a PM indicator on the top left of the display.
How To Set The Alarm Time
1. Press and hold the
2. Holding down the
button, press the
button until the exact time you want appears.
3. Release the
How To Set The Alarm Mode
Your Wake & Shake provides several alarm options. These
options are the same for both the clock alarm and the phone ring
Using the Alarm Mode Switch, you may choose from the fol-
Shaker & Audible Alarm
Audible Alarm & Strobe Light
Strobe Light & Shaker
V = Shaker (Vibration)
S = Sound (Audible Alarm)
F = (Strobe Light)
Turning the Clock & Telephone
Ring Signaler On
Adjust the Alarm Function Switch to the setting you prefer.
Clock alarm & telephone ring Signal on
Both clock alarm and telephone ring
Telephone Ring Signaling only
When the alarm is set to one of the modes, the alarm indicator
will appear on the display.
Your Wake & Shake distinguishes between the clock alarm and
telephone ring alarm by using different patterns. See the table below:
When your clock alarm goes off, you can temporarily turn it off
button will stop the alarm for 9
minutes. After 9 minutes, the alarm will activate again. You can
continue to hit the
button for a total of 2 hours after which the
alarm mode will be automatically switched off.
The Snooze button is located at the top of the display. It is also
the strobe flasher.
Alarm Off Button
When your clock alarm is activated, you can press the
Button on the front of your clock to turn the alarm off. The alarm will
still be set for the same time and will operate at the same time the
If your alarm is activated but never switched off, it will automati-
cally turn off after 2 hours.
Telephone Ring Signaler
1. Make sure your Wake & Shake has been installed using the phone
cord and is plugged into your telephone wall jack.
2. Adjust the Ringer On/Off switch to A+T (for clock alarm & telephone
alarm) or T (for just telephone alarm).
3. Choose one of the alarm modes. (See page 4).
4. When your Wake & Shake alerts you there is an incoming call,
simply answer your telephone and the alarm will stop. When you
hang up, your Wake & Shake is ready to indicate the next call.
To adjust the brightness of the display, simply move the Dimmer
Control located on the back of your clock.
Volume and Tone Control
Your Wake & Shake allows you to adjust both the volume and tone
of the alarm. The Volume Control increases or decreases the loud-
ness of the alarm. The Tone Control shapes the sound by making it a
higher pitch or a lower pitch.
To adjust the
, simply turn the dials located on the
front of your clock.
You can adjust the strength of the bed shaker by setting the Shaker
Switch to Lo (-) or Hi (+).
It is not required to install a battery for your Wake & Shake to
function. You can use just the AC power adapter, however with a bat-
tery installed, the clock will keep the time and alarm settings in the
event of a power outage. It is strongly suggested that you do install a
9V battery. Check the battery after 1 year as an old battery can leak
and damage your clock.
ClearSounds Communications warrants the WS1 Wake &
Shake Clock against any defect in materials or workmanship for
the period of one year from the date of purchase.
Within a period of one year from purchase date, ClearSounds
Communications will repair or replace (our discretion) your WS1
Wake & Shake Clock at no cost. If we elect to replace your clock,
we may replace it with a new or reconditioned product of the same
or similar design. Repair or replacement will be warranted for a
period of 90 days or the original time on the original warranty,
whichever is longer.
The guarantee does not cover accidents, negligence or breakage
to any parts. This includes shipping damage, failure to follow
instructions, misuse, fire, floods, use of incompatible accessories,
Acts of God or failure in your phone service carrier’s line service.
The product must not be tampered with or taken apart by anyone
who is not an authorized ClearSounds Communications rep-
resentative. Tampering with the clock will void any written or implied
ClearSounds Communications shall not be responsible for loss
of time, inconvenience, loss of use of your WS1, property damage
caused by your WS1 or any other incidental or consequential damages.
Warranty service is available only with proof of purchase.
IMPORTANT: YOUR RECIEPT IS PART OF YOUR GUARANTEE
AND MUST BE RETAINED AND PRODUCED IN THE EVENT OF
A WARRANTY CLAIM
Shipping cost must be prepaid and the product must be
packaged appropriately for shipping.
Part 68 of FCC Rules Information
This equipment complies with Part 68 of the FCC rules and
the requirements adopted by the ACTA. On the bottom of this equip-
ment is a label that contains, among other information, a product
identifier in the format US:AAAEQ##TXXXX. If requested, this
number must be provided to the telephone company. A plug and
jack used to connect this
to the premises wiring and
telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant tele-
phone cord and modular plug, RJ11
USOC, is provided with this
product. It is designed to be connected to a compatible modular
jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone
line may result in the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of RENs should not exceed
five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the
local telephone company. For products approved after July 23,
2001, the REN for this product is part of the product identifier that
has the format US:AAAEQ##TXXXX. The digits represented by
## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the label. If
this telephone equipment, the WS1, causes harm to the telephone
network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if ad-
vance notice isn’t practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your
right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equip-
ment, operations or procedures that could affect the operation of
the equipment. If this happens the telephone company will pro-
vide advance notice in order for you to make necessary modifi-
cations to maintain uninterrupted service. If trouble is experienced
with this telephone equipment, for repair or warranty information,
please contact ClearSounds Communication at 1-800-965-9043.
If the equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the equip-
ment until the problem is resolved.
DO NOT DISASSEMBLE THIS EQUIPMENT.
equipment is not intended to be repaired and it contains no repairable
parts. Opening the equipment or any attempt to perform repairs will
void the warranty. For service or repairs, call 1-800-965-9043.
Connection to party line service is subject to state tariffs. Contact
the state public utility commission, public service commission or
corporation commission for information.
8160 Madison Ave., Burr Ridge, IL 60527
800.956.9043 V — 800.536.8890 TTY
630.654.9219 FAX • www.clearsoundscom.com