Full Text Searchable PDF User Manual
Beamforming Microphone Array 2
Group Microphone for Professional Conferencing
Quick-Start Guide
THE BEAMFORMING MICROPHONE ARRAY 2 ...............................1
QUICK-START OVERVIEW ................................................................2
CONNECTING THE BFM2 ................................................................3
UPDATING THE BFM2 FIRMWARE ..................................................4
TESTING THE MICROPHONE ARRAY ..............................................4
V
olume
and
m
ute
.................................................................................5
m
icrophone
a
rray
i
ndicators
...............................................................5
MOUNTING THE BFM2 .....................................................................5
COMPLIANCE ....................................................................................6
PART NUMBERS
...................................................................................
6
Table of Contents
QUICK-START GUIDE
1
THE BEAMFORMING MICROPHONE ARRAY 2
The Beamforming Microphone Array 2 (BFM2) is a 2nd generation
Beamforming Microphone Array product featuring 24 microphones,
beamforming and adaptive steering technology designed specifically for
the CONVERGE® Pro 2 products: 128, 128D, 128T, 128TD, 128V, 128VD,
120, and 48T. The BFM2 connects with the CONVERGE Pro 2 through a
Peripheral Link (P-Link) port. 3 arrays per supported CONVERGE Pro 2
and up to 6 BFM2s can be daisy-chained in one P-Link chain. The Power
for the BFM2 is supplied through a Power-Over-Ethernet (PoE) or P-Link
connection from CONVERGE Pro 2.
The BFM2 is supported for use as a ceiling-mounted, wall-mounted or
tabletop assembly.
IMPORTANT:
The BFM2 only can be used with CONVERGE
Pro 2 systems. It is not compatible with CONVERGE Pro or first
generation Beamforming Microphone Array systems.
The latest version of the CONVERGE Pro 2 firmware can be found on the
ClearOne website at:
http://www.clearone.com/resources#professional_audio
The latest version of the BFM2 firmware and the Beamforming
Microphone Array 2 Installation Guide can be found on the ClearOne
website at:
http://www.clearone.com/resources#professional_microphones
BEAMFORMING MICROPHONE ARRAY 2
2
QUICK-START OVERVIEW
Installing and using the BFM2 in your CONVERGE Pro 2 site is subject to
the following rules:
1. The BFM2 can only be used with CONVERGE Pro 2 systems.
2. You must have a CONVERGE Pro 2 128, 128D, 128T, 128TD, 128V,
128VD, 120, and/or 48T in the site. The BFM2 will not work with
standalone 128SR or 128SRD units.
3. You can have up to 3 BFM2s per valid CONVERGE Pro 2 unit up
to a total of 6 BFM2s per P-Link chain. More valid CONVERGE Pro
units may be added to increase the number of BFM2s per site.
Quick Start Procedures
These steps must be done in the following order to use the BFM2 in your
CONVERGE Pro 2 Site:
1. Update the CONVERGE Pro 2 firmware to the latest version using
CONVERGE Pro 2 CONSOLE software.
2. Connect the BFM2 to the updated CONVERGE Pro 2 via the P-Link
bus.
3. Update the BFM2 firmware using CONVERGE Pro 2 CONSOLE.
(The BFM2 firmware can not be upgraded directly without an
updated CONVERGE Pro 2.)
4. Test the BFM2
5. Mount the BFM2
QUICK-START GUIDE
3
CONNECTING THE BFM2
Connect the BFM2 units to the CONVERGE Pro 2 via the P-Link
connections using CAT6-24AWG solid conductor RJ45 cables.
The BFM2 can be powered via a P-Link
1
from CONVERGE Pro 2 (a single
cable carries power, audio and control), a PoE power supply
2
(external
or ClearOne; a maximum of three BFM2 units can be powered by one
ClearOne PoE Injector),or a standard PoE switch
3
.
The power-source-selection switch should be set towards PoE if the
BFM2 is powered by PoE, or set towards P-Link if powered by P-Link.
power-source-selection
switch
(for future use)
1
1
2 3
4
Daisychain Examples
Example 1
shows a basic daisychain of three BFM2 arrays to a single
CONVERGE Pro 2 unit:
Example 2
illustrates a daisychain of four BFM2 arrays to two
CONVERGE Pro 2 units:
QUICK-START GUIDE
5
UPDATE BFM2 FIRMWARE
1. Connect the P-Link cable between the CONVERGE Pro 2 units and
the BFM2s.
2. Connect the CONVERGE Pro 2 units with CONVERGE Pro 2
CONSOLE.
3. Open the Firmware Loader screen.
4. Browse for the bf2_mic.mdo file.
5. Download the BFM2 firmware.
6. The BFM2(s) will default and reboot after the download of firmware.
7. Units are fully upgraded. (All BFM2 units connected via the P-Link
on the site are simultaneously updated.)
8. Restore the saved site file to the system using CONVERGE Pro 2
CONSOLE.
TEST THE BFM2
The BFM2 must be added to the site using the CONVERGE Pro 2
CONSOLE software. This software also provides the capability of
configuring the beams (enable/disable) and other characteristics
available in Configuration mode. Refer to the online help available with the
CONVERGE Pro 2 CONSOLE software.
V
olume
& m
ute
These controls are available through the controller configured for your
CONVERGE Pro 2 site.
6
m
icrophone
A
rrAy
leD i
nDicAtors
The illuminated microphone indicators at the ends of the BFM2 show
blue/red when the microphone array is active/muted. You can set the
indicators to remain off by using CONVERGE Pro 2 CONSOLE to change
Unit Properties for the BFM2. See the help file for more details.
MOUNT THE BFM2
The array can be ceiling-mounted in either a suspended or solid ceiling,
or on a wall-mount assembly with the PoE or P-Link wiring passing
through the mounting assembly and plugging into the BFM2 unit.
Tabletop use is also supported with PoE or P-Link cables attached under
the unit.
NOTE:
1st Gen BFM mounting kits are compatible with 2nd Gen
BFM2 unit and vice versa.
Detailed instructions are included in the BFM2 Installation Guide
available on the ClearOne website:
http://www.clearone.com/resources#professional_microphones
QUICK-START GUIDE
7
Part Numbers
Item
White color SKU
Black color SKU
Beamforming Microphone Array 2
910-3200-201
910-3200-201-B
BMF2 Ceiling Mount kit with 12” Suspension Column
910-3200-203-12
910-3200-203-12-B
BMF2 Ceiling Mount kit with 24” Suspension Column
910-3200-203-24
910-3200-203-24-B
BMF2 Ceiling Mount kit with 36” Suspension Column
910-3200-203-36
910-3200-203-36-B
BMF2 Ceiling Mount kit with 48” Suspension Column
910-3200-203-48
910-3200-203-48-B
BMF2 Ceiling Mount kit without Suspension Column
910-3200-203
910-3200-203-B
BFM Ceiling Mount kit with 12” suspension column
910-001-005-12
910-001-005-12-B
BFM Ceiling Mount kit with 24” suspension column
910-001-005-24
910-001-005-24-B
BFM Ceiling Mount kit with 36” suspension column
910-001-005-36
n/a
BFM Ceiling Mount kit with 48” suspension column
910-001-005-48
n/a
BFM Wall Mount
910-001-006
910-001-006-B
PoE Power Supply Kit
910-3200-202
50 Ft RJ45 CAT6 Cable
910-3200-204-50
100 Ft RJ45 CAT6 Cable
910-3200-204-100
150 Ft RJ45 CAT6 Cable
910-3200-204-150
200 Ft RJ45 CAT6 Cable
910-3200-204-200
COMPLIANCE
Details on compliance can be found on the ClearOne website under
“Resource Library”.
BEAMFORMING MICROPHONE ARRAY
8
© 2016 ClearOne, Inc. All rights reserved.
Information in this document is subject to change without notice. QSG-0031-001 Rev 1.0 AUGUST 2016
HEADQUARTERS:
Salt Lake City, UT USA
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
Tel:
801.975.7200
Toll Free:
800.945.7730
Sales:
800.707.6994
Fax:
801.303.5711
e-mail:
sales@clearone.com
Europe
Tel:
+44.1454.616.977
UK Tech Support:
+44.0800.680.0682
e-mail:
global@clearone.com
Asia Pacific
Tel:
+86.138.23287825
Tech Support:
+86.18420152949
e-mail:
global@clearone.com
Middle East
Tel:
+
91.9930782195
e-mail:
global@clearone.com
TechSales
Tel:
800.705.2103
e-mail:
techsales@clearone.
com
Technical Support
Tel:
800.283.5936
Tel:
801.974.3760
e-mail:
tech.support@clearone.
com
CLEARONE LOCATIONS