C-Nav C-Nav3050 Quick Start Manual - User Manual

Full Text Searchable PDF User Manual

C-Nav3050 Quick Start Guide

CNV96-310033-3001, Rev. C

Follow this Quick Start Guide to enable the robust functionality of
the C-Nav3050.

Your C-Nav3050 has already been tested by qualified

C-Nav Technicians. Refer to the following steps to
connect equipment and operate the receiver.

This Quick Start Guide is intended to familiarize the user with
the basic setup of the C-Nav3050 only. The supplied C-
Nav3050 USB Flash Drive (P/N 7CNG002-0) and Product
DVD (6000001-XX) include the C-Nav3050 User Guide (P/N
CNV96-310034-3001,

Adobe Reader required

), which

contains in-depth product information and technical
specifications. Refer to the table below for items included in
the C-Nav3050 GNSS Sensor Kit.

Table 1: Supplied Equipment

C-Nav3050 GNSS Sensor
(P/N CNV92-310413-3002LF)

GNSS Antenna, TNC, 5/8” Mount

(P/N NAV82-001020-3001LF)

Y-Cable, Positronic 9-Pin Male to USB 2.0 Device Plug
& DB9S (RS-232/RS-422), 6 ft
(P/N NAV94-310273-3006LF)

Y-Cable, Positronic 9-Pin Male to Ethernet RJ45 Plug &
DB9S (RS-232/1PPS), 6 ft
(P/N NAV94-310272-3006LFB)

Mounting Brackets, 2
(P/N NAV88-310442-3001LF)

Antenna Mounting Adapter, 1”-14 UNS-2B to 5/8”, 2” L

x 1 3/8” diameter
(P/N 3250005-0)

Antenna Mounting Pole, 12” x 1” diameter

(P/N WES534610)

DVD-ROM, C-Nav3050 Software Applications
(P/N 6000001-XX)

C-Nav3050 USB Flash Drive, 2GB
(P/N 7CNG002-0)

USB host-to-host receptacle adapter
(P/N QVSCC2208-FF)

RS232/422 Dual-data Adapter
(P/N CNV335G001-0)

1PPS Adapter

(P/N CNV335G002-0)

Cable, Power / 1PPS / Event, Positronic 9-Pin Female
Unterminated, 10ft, w/ Filter

(P/N NAV94-310274-3010LF)

AC Power Supply Kit

(P/N CNV82-020007-3001LF)

Shipping Carton
(P/N NAV79-200304-0001)

C-Nav3050 Quick Start Guide
(P/N CNV96-310033-3001)

*Item not included in C-Nav3050 Sensor Kit with P/N CNV92-
31046-3001B.

NOTE: C-Nav3050 GNSS Sensor Kit with P/N
CNV92-31046-3001B is not MED Wheelmark
Approved.

Connect Equipment

Figure 1: C-Nav3050 Rear View

Refer to

Figure 1

above for the steps below:

Use one of the two supplied data cables for
communications:



Ethernet RJ45 / DB9S female Y-cable (P/N
NAV94-310272-3006LF): Connect the Positronic
9-Pin connector of the cable to COM1 - LAN at the
rear of C-Nav3050. Connect the DB9S end to the
computer or C-NaviGator CDU.

Or…



USB 2.0 Device Plug / DB9S female Y-cable (P/N
NAV94-310273-3006LF): Connect the Positronic
9-Pin connector of the cable to COM2 - USB at the
rear of C-Nav3050. Connect the DB9S end to the
computer or C-NaviGator CDU.

Mount the GNSS antenna. Locate the antenna in an area
with a 360



clear view of the sky. Refer to

Section 4 -

Installation

of the C-Nav3050 User Guide for detailed

installation instructions.

3. Connect the TNC connector on one end of a C-Nav

approved GNSS antenna cable to the GNSS antenna.

Connect the other end of the cable to the TNC connector,
labeled ANT, at the rear of the C-Nav3050.

Optional C-Nav-approved Antenna Cables are available

through your authorized C-Nav Dealer, or by contacting
C-Nav Support.

Perform one of these steps to setup power:

If you are connecting using the optional Positronic
9-Pin Female Unterminated Power Cable (P/N
NAV94-310274-3010LF), connect the power cable
to the connector labeled POWER, at the rear of
the C-Nav3050. Connect the unterminated end of
the power cable to a DC power source (9 to
32VDC, 6W typical, see

Section 3

– Interfacing

the C-Nav3050 User Guide for power cable pin
assignments).

If you are connecting using the optional AC Power
Supply Kit (P/N CNV82-020007-3001LF), connect
the Positronic 9-Pin Female connector of the
Power Supply Unit (P/N NAV82-020007-3001LF)
to the connector labeled POWER, at the rear of
the C-Nav3050. Insert an AC Power Cord into the
2-prong receptacle on the PSU, based on regional
AC power availability (110, 220 or 240 VAC power
cords provided) and plug into an appropriately
rated wall receptacle.

Press the front panel On / Off switch

to turn on the

C-Nav3050. All front panel LEDs illuminate for 3-5
seconds during power-up. The Power / GNSS Status LED
changes from Red to Green. Refer to

Section 3 -

Interfacing

of the C-Nav3050 User Guide for LED status

descriptions.

Figure 2: C-Nav3050 LED Indicator Panel

Your C-Nav3050 hardware is now properly connected.

At this point you may connect to C-

Nav’s C-Setup,

C-Monitor, or C-NaviGator controller solutions to view
real-time positioning data and to control the C-Nav3050.

The C-Nav Corrections Service license is not a

standard feature of any Software Bundle. It is
purchased separately. Refer to the reverse side of this
pamphlet for more information on obtaining a C-Nav
license.

ANTENNA

COM1 - LAN

POWER

COM2 - USB

C-Nav3050 Quick Start Guide

CNV96-310033-3001, Rev. C

How to Obtain a C-Nav License

The C-Nav Corrections Service is a subscription service. The
user pays a subscription fee, which licenses the use of the
service for a predetermined period of time. Subscriptions are
requested by completing the online request form at:

http://www.cnav.com/code

, via a C-Nav authorized

representative, or by contacting C-Nav at:

authcode@cnav.com.

C-Nav recommends that customers process new C-Nav license
requests 15 to 30 days before the expiration of the current
license.

The requirements to obtain a C-Nav license are:



Valid Purchase Order



Signed License Agreement



Appropriate Credit Terms with C&C Technologies,
Inc., or an Authorized Dealer; including a valid P.O

When contacting C-Nav regarding subscription or deactivation
of service, please provide the following information:



Vessel Info and brief project description (Name /
Number, Location)



Customer Info (Company Name, PO/Ref. Num.
Point of Contact)



C-Nav Equipment Details (Receiver Type,
Firmware version, Serial Number, P/N’s, etc)



Required Start / Stop Date or Period



Service Type (Land or Offshore, Activation or
Deactivation)



Operational Region (Asia, Australia, China, South
and Central America, Caribbean, Africa, Middle
East, or Other)



Detailed Contact Information (Phone, Fax, E-Mail,
Billing / Shipping Addresses)

An authorized subscription will provide an encrypted code,
which is specific to the Serial Number of the C-Nav receiver to
be authorized. This is entered into the receiver Over-the-Air, or
via a C-Nav controller solution (i.e. C-Setup, C-Monitor, or
C-NaviGator CDU).

Over-the-Air C-Nav Licensing

Over-the-Air (OTA) C-Nav Licensing is the easiest way to
install a C-Nav Corrections Service license. The installation of a
purchased license is accomplished via radio broadcast. Over-
the-Air C-Nav Licensing is especially convenient for receivers
in remote locations in the field.

The customer should do the following in order to properly receive
the CCS Over-the-Air broadcast of the C-Nav license:

Turn on the C-Nav3050 Receiver.

Ensure that the C-Nav3050 Antenna has clear
access to the CCS tracking satellite.

Request the C-Nav license.

Once a C-Nav license is activated, the C-Nav Status LED on
the C-Nav3050 Front Panel will be solid green.

Figure 3: Front Panel C-Nav Status LED -

Showing Active C-Nav License

C&C Technologies, Inc. C-Nav DGNSS Division

730 East Kaliste Saloom Rd

Lafayette, Louisiana, USA, 70508

E-mail:

support@cnav.com

Tel: +1 337 210 0000
Fax: +1 337 210 0003

Website:

www.cnav.com

Ask a Question ?