Full Text Searchable PDF User Manual
IEC INSTALLATION INSTRUCTION AND
MAINTENANCE MANUAL
FOR CRYSTALLINE SOLAR PV MODULE
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 1 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
1.
INTRODUCTION
This installation instruction manual provides information about CNPV Crystalline Solar Photovoltaic Modules.
CNPV Dongying Solar Power Company Limited has a history of successful innovation within the Solar Industry.
The company was founded in 2006 and has made significant investments in research and development, creating over
10 patents during the company’ history.
The company has several fully integrated product lines including ingots, casting, wafers, Cells and Modules of Mono
and Poly crystalline, and those products are also exported to overseas markets. With an experienced international
management team and a strong reputation for innovation, CNPV is one of the leaders in China’s Solar Energy Sector
and provides the highest quality SPV Modules in a range of sizes designed to meet the requirements of the most
demanding energy and power users worldwide.
2.
POWER MODULE
CNPV Solar Photovoltaic Modules consist of a series of electrically interconnected crystalline silicon solar cells,
which are permanently encapsulated between a low iron toughened glass superstrate and substrate. The entire
laminate is secured within an anodized aluminum frame for structural strength; ease of installation and to protect the
cells from the most severe environmental conditions.
3.
APPLICATIONS
CNPV SPV Modules are a highly reliable, virtually maintenance-free direct current (DC) power source, designed to
operate most efficiently in sunlight. CNPV series Modules are ideal to power remote homes, recreational vehicles,
water pumps, telecommunication systems and many other applications either with or without the use of storage
batteries.
4.
PERMIT
Before installing your system, contact local authorities to determine the necessary permit, installation and inspection
requirements.
5.
CLIMATE CONDITION
Install the CNPV Solar Photovoltaic Crystalline series Modules in the following conditions:
Ambient temperature: -20°C to +40°C.
Operating temperature: -40°C to +85°C.
Storage temperature: -40°C to +40°C,
Humidity: below 85RH%
Wind pressure: below 50.12lb / ft
2
(2400Pa).
Snow Load Pressure: below 112.76lb / ft
2
(5400Pa).
Corrosion resistance: Except for heavy corrosive salt area and sulfurous area.
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 2 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
6. SITE SELECTION
In most applications, CNPV SPV Modules should be installed in a location where they will receive maximum
sunlight throughout the year. In the Northern Hemisphere, the Module should typically face south, and in the
Southern Hemisphere, the Modules should typically face north. Modules facing 30 degrees away from true South (or
North) will lose approximately 10 to 15 per cent of their power output. If the Module faces 60 degrees away from
true South (or North), the power loss will be 20 to 30 per cent.
When choosing a site, avoid trees, buildings or obstructions, which could cast shadows on the solar photovoltaic
Modules especially during the winter months when the arc of the sun is lowest over the horizon. Shading causes loss
of output, even though the factory fitted bypass diodes of the SPV Module will minimize any such loss.
Do not install the SPV Module near naked flame or flammable materials.
Do not install the SPV Module in a location where it would be immersed in water or continually exposed to water
from a sprinkler or fountain etc.
7.
MODULE TILT ANGLE
CNPV SPV Modules connected in series should be installed at same orientation and angle. Different orientation or
angle may cause loss of output power due to difference of amount of sunlight exposed to the Module.
CNPV SPV Modules produce the most power when they are pointed directly at the sun. For installations where the
SPV Modules are attached to a permanent structure, the SPV Modules should be tilted for optimum winter
performance. As a rule, if the system power production is adequate in winter, it will be satisfactory during the rest of
the year. The Module tilt angle is measured between the solar Modules and the ground (Figure 1). Optimal tilting of
SPV Module is almost the same as the latitude of installation location.
SUNLIGHT
TILT ANGLE
MODULE
HORIZONTAL
Figure 1 SPV Module Tilt Angle
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 3 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
8. MOUNTING AND NOTES
Systems should be installed by qualified personnel only. It involves electricity, and can be dangerous if the personnel
are not familiar with the appropriate safety procedures.
The Module frame is made of anodized aluminum, and therefore corrosion can occur if the Module is subject to a
salt water environment with contact to a rack of another type of metal (Electrolysis Corrosion). If required, PVC or
stainless steel washers can be placed between the SPV Module frame and support structure to prevent this type of
corrosion. Module support structures that are to be used to support SPV Modules at correct tilt angles should be wind
and snow load rated for use by the appropriate local and civil codes prior to installation.
CNPV SPV Modules can be mounted as following method:
Figure 2 Mounting Method a and b
a)
Using corrosion-proof screws (M8) on the existing installing holes (see drawing 1, 3, 5 & 7) in the Module
frame. The frame of each Module has 4 or 8 mounting holes (12mm×9mm) used to secure the Modules to
supporting structure. The Module frame must be attached to a supporting rack using M8 stainless steel hardware
together with spring washers and flat washers in four places symmetrical on the SPV Module. See method a of
figure 2. The applied torque is about 8 Newton-meters.
b)
Using suitable Module clamps on the Module frame, see method b of figure 2. The module frame must be
attached to supporting rack using M8 stainless steel hardware together with corrosion-proof clips in four places
on the SPV module. See drawing 10, 12, 14 & 16,
with clamping clip,
for positioning of clamping clips. The
applied torque is about 8 Newton-meters. See figure 3 if clamping mounting is on short frames of the module.
W
idth
1/
4W
1/4
W
Length
c)
Insertion System
Method a: Using corrosion-proof
screws on existing Installation
Method b. Using suitable module
clamps on the module frame
Using Short sides for module clamping. W
means module width, and 1/4W means
permissible clamping range.
Figure 3. Mounting on short frames.
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 4 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
NOTES:
(1) The Module clamps must not come into contact with the front glass and must not deform the frame. Avoid
shadowing effects from the Module clamps and the insertion systems. It is not permitted to modify the Module frame
under any circumstances. Recommended distance between 2 Solar Modules is 5mm considering linear thermal
expansion of the Module frames.
(2) Clearance between the Module frame and mounting surface may be required to prevent the junction box from
touching the surface, and to circulate cooling air around the back of the Module.
(3) The Modules are not designed for integral mounting as part of a roof or wall. The mounting design may have an
impact on the fire resistance. If the Modules are to be installed on the roof or wall of a building, the fire resistance of
roof covering or wall should be rated for the application. Here the standoff method or the rack method is
recommended. The Modules are supported parallel to surface of the building wall or roof. Clearance between the
Module frames and surface of the wall or roof is required to prevent wiring damage and to allow air to circulate
behind the Module. The recommended stand-off height is 115mm. Any slope less than 5in/ft (127mm/305mm)
required to maintain a fire class rating. Do not mount SPV Module in such way that the drain holes of SPV Module
are intended to block up.
(4) Do not step on the Module, although SPV Modules are quite rugged, the glass can be broken (and the Module
will no longer work properly) if it is dropped or hit by tools or other objects.
9. GROUNDING
All Module frames and mounting racks must be properly grounded in accordance with the local regulations. Proper
grounding is achieved by connecting the Module frame(s) and structural members contiguously one to another using
a suitable grounding conductor. The grounding conductor or strap may be copper, copper alloy, or other material
acceptable for use as an electrical conductor per local regulations. The grounding conductor must then make a
connection to earth using a suitable earth ground electrode.
Attach a separate conductor to one of the
4mm diameter grounding holes marked
'
' on the Module frame with a screw
and nut that incorporates an external tooth
washer. This is to ensure positive electrical
contact with the frame.
The rack must also be grounded unless they are mechanically connected by nuts and bolts to the grounded SPV
Modules. The array frame shall be grounded in accordance with local regulations.
Figure 4 Schematic drawing
for SPV Module grounding
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 5 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
10. BYPASS DIODES AND BLOCKING DIODES
Partial shading of an individual Module can cause a reverse voltage across the shaded SPV Module. Current is then
forced through the shaded area by the other Modules.
When a bypass diode is wired in parallel with the series string, the forced current will flow through the diode and
bypass the shaded SPV Module, thereby minimizing Module heating and array current losses.
In system utilizing a battery, blocking diodes are typically placed between the battery and the SPV Module output to
prevent battery discharge at night.
Diodes that are used as blocking diodes must: Have a Rated Average Forward Current [I
F(AV)
]
above
maximum
system current at highest Module operating temperature. Have a Rated Repetitive Peak Reverse Voltage [V
RRM
]
above
maximum system voltage at lowest Module operating temperature.
11. WARNING AND NOTES
The SPV Modules generate electricity when exposed to light. Array of many Modules can cause lethal electrical
shock and burn hazards. Only authorized and trained personnel should have access to these Modules. To reduce the
risk of electrical shock or burns, modules maybe covered with an opaque material during installation to avoid
electrical shocks or burns. Do not touch live terminals with bare hands. Use insulated tools for electrical connections.
Use appropriate methods to mount SPV Modules. Fall of Modules from high place will cause death, injury or
damage.
The SPV Module has a pair of male and female waterproof connectors. For a series electrical connection, connect
positive (+) connector of first SPV Module to negative (-) connector of the following Module.
Do not short the positive and the negative. Do not disconnect under load. Be sure connectors have no gap between
the insulators. In case there is a gap, a fire and/or an electrical shock may occur.
NOTES:
(1) Artificially concentrated sunlight shall not be directed on the SPV Module. The rated electrical characteristics are
within 10 percent of measured values under standard test conditions (Irradiance of 1000W/m
2
, AM 1.5 spectrum, and
cell temperature of 25°C).
(2) Under normal conditions, a solar photovoltaic Module is likely to experience conditions that produce more
current and/or voltage than reported at standard test conditions. Accordingly the value of Isc and Voc marked on this
Module should be multiplied by a factor of 1.25 when determining component voltage ratings, conductor current
ratings, fuse sizes, and sizes of controls connected to the SPV output.
(3) Details for wiring in accordance with the local regulations.
(4) If you install modules in parallel electrically, each module (or series string of modules so connected) shall be
provided with the maximum series fuse as specified.
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 6 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
12. MODULE WIRING
Each Module has two #12 AWG type standard 90°C sunlight resistant output cables each terminated with plug & ply
connectors. This cable is suitable for applications where wiring is exposed to the direct rays of the Sun. We
recommend that all wiring and electrical connections comply with local regulations.
For field connections, use the minimum No. #12 AWG copper wires insulated for a minimum of 90°C and sunlight
resistant as well. The minimum and maximum outer cable diameters of the cable are 5 to 7mm. Refer to table 1 for
the maximum electrical rating of series fuse.
13. TYPE OF PRODUCT APPLICATION
“The modules are qualified for application class A: Hazardous voltage (IEC61730: higher than 50V DC; EN61730:
higher than 120V), hazardous power applications (higher than 240W) where general contract access is anticipated
(Modules qualified for safety through EN IEC61730-1 and EN IEC61730-2 within this application class are
considered to meet the requirements for Safety class II)”
14. MAINTENANCE
Under most weather conditions, normal rainfall is sufficient to keep the SPV Module glass surface clean. If dirt
build-up becomes excessive, clean the glass only with a soft cloth using mild detergent and water. USE CAUTION
WHEN CLEANING THE BACK SURFACE OF THE MODULE TO AVOID PENETRATING THE SUBSTRATE
MATERIALS. SPV Modules that are mounted flat (0° tilt angle) should be cleaned more often, as they will not ''self
clean'' as effectively as Modules mounted at a 15° tilt or greater. Once a year, check the tightness of terminal screws
and the general condition of the wiring. Also, check to be sure that mounting hardware is tight. Loose connections
will result in damage for array. Changed SPV Module must be the same kind and type. Do not touch live parts of
cables and connectors. Use appropriate safety equipment (insulated tools, insulating gloves, etc.), when touching
them.
Cover the front surface of the SPV Module by an opaque or other material when repairing. The SPV Modules when
exposed to sunlight generate high voltage and are dangerous.
15. SPECIFICATIONS:
See Table1
Notes
1.
Standard Test Condition(STC) of Irradiance of 1000W/m²
，
AM1.5 Solar Spectrum & 25
ºC
cell temperature
2.
Nominal Operating Cell Temperature (NOCT): 45±2
ºC
3.
The tolerance of Voltage and Current within ±10%
4.
Temperature coefficient of Current is 0.05%/
º
K
5.
Temperature coefficient of Voltage is -0.30%/°K
6.
See SPV Module drawing for mounting and grounding holes locations. The drawing for CNPV-xxxxM and
CNPV-xxxxB(Black module) is identical.
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 7 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
Table 1: Electrical and Mechanical Specifications.
Module
Series
Model
Dimensions
(mm)
Weight
(kg)
Electrical Performance @ STC
Max-System
Voltage (VDC)
Max-Series
Fuse (A)
Recommended Max.
Module Number
P
max
(Wp)
V
Pm
(V)
I
Pm
(A)
V
OC
(V)
I
SC
(A)
In Series
In Parallel
7
2
p
cs
1
25×
125
mm
SPV Modu
le
(Mo
n
o-Crys
ta
ll
ine Si
li
co
n )
CNPV-160M
1581×809×35 15
160 34.5 4.65 43.0 5.15
IEC6
121
5/
IEC6
173
0:
100
0VD
C
10
17 2
CNPV-165M
165 35.2 4.70 43.4 5.20
17
2
CNPV-170M
170 35.8 4.75 43.8 5.25
17
2
CNPV-175M
175 36.6 4.80 44.2 5.30
17
2
CNPV-180M
180 37.2 4.85 44.6 5.35
17
2
CNPV-185M
185 37.8 4.90 45.0 5.40
17
2
CNPV-190M
190 37.8 5.05 45.1 5.55
17
2
CNPV-195M
195 37.9 5.15 45.2 5.60
17
2
CNPV-200M
200 38.0 5.25 45.3 5.65
17
2
CNPV-205M
205 38.1 5.38 45.4 5.70
17
2
CNPV-210M
210 38.2 5.50 45.6 5.80
17
2
7
2
p
cs
1
25×
125
mm
SPV Modu
le-B
lack
(Mo
n
o-Crys
ta
ll
ine Si
li
co
n )
CNPV-160MB
160 34.5 4.65 43.0 5.15
17
2
CNPV-165MB
165 35.2 4.70 43.4 5.20
17
2
CNPV-170MB
170 35.8 4.75 43.8 5.25
17
2
CNPV-175MB
175 36.6 4.80 44.2 5.30
17
2
CNPV-180MB
180 37.2 4.85 44.6 5.35
17
2
CNPV-185MB
185 37.8 4.90 45.0 5.40
17
2
CNPV-190MB
190 37.8 5.05 45.1 5.55
17
2
CNPV-195MB
195 37.9 5.15 45.2 5.60
17
2
CNPV-200MB
200 38.0 5.25 45.3 5.65
17
2
CNPV-205MB
205 38.1 5.38 45.4 5.70
17
2
CNPV-210MB
210 38.2 5.50 45.6 5.80
17
2
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 8 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
Module
Series
Model
Dimensions
(mm)
Weight
(kg)
Electrical Performance @ STC
Max-System
Voltage
(VDC)
Max-Series
Fuse (A)
Recommended Max.
Module Number
P
max
(Wp)
V
Pm
(V)
I
Pm
(A)
V
OC
(V)
I
SC
(A)
In Series
In Parallel
54p
cs 15
6×
15
6mm
SP
V
Modul
e
(Mon
o-C
rys
ta
lli
ne Sili
co
n)\
CNPV-190M-54
1482×992×35
18
190 26.6 7.15 32.6 7.90
IEC6
121
5/
IEC6
173
0:
100
0VD
C
20
23
3
CNPV-195M-54
195 26.9 7.25 32.8 8.00
23
3
CNPV-200M-54
200 27.0 7.40 33.0 8.10
23
3
CNPV-205M-54
205 27.2 7.55 33.2 8.20
23
3
CNPV-210M-54
210 27.4 7.65 33.4 8.30
23
3
CNPV-215M-54
215 27.6 7.80 33.6 8.40
23
3
CNPV-220M-54
220 27.7 7.95 33.7 8.50
23
3
CNPV-225M-54
225 27.8 8.10 33.8 8.60
23
3
CNPV-230M-54
230 28.0 8.20 33.9 8.70
23
3
CNPV-235M-54
235 28.3 8.30 34.0 8.80
23
3
CNPV-240M-54
240 28.7 8.35 34.1 8.85
23
3
60p
cs 15
6×
15
6mm
SP
V
Modul
e
(Mon
o-C
rys
ta
lli
ne Sili
co
n)
CNPV-220M
1650×992×35 20
220 29.7 7.40 36.8 8.00
20
21
3
CNPV-225M
225 30.0 7.50 37.0 8.10
21
3
CNPV-230M
230 30.3 7.60 37.2 8.20
21
3
CNPV-235M
235 30.7 7.65 37.5 8.30
21
3
CNPV-240M
240 30.8 7.80 37.6 8.40
21
3
CNPV-245M
245 30.9 7.93 37.7 8.50
21
3
CNPV-250M
250 31.0 8.05 37.8 8.60
21
3
CNPV-255M
255 31.3 8.15 37.9 8.70
21
3
CNPV-260M
260 31.5 8.25 38.0 8.80
21
3
CNPV-265M
265 31.7 8.35 38.1 8.90
21
3
72p
cs 15
6×
15
6mm
SP
V
Modul
e
(Mon
o-C
rys
ta
lli
ne Sili
co
n)
CNPV-255M
1965×992×40 24
250
35.9 7.10 43.2 7.70
20
17 3
CNPV-260M 260
36.1 7.20 43.4 7.80
17 3
CNPV-265M
265 36.3 7.30 43.6 7.90
17 3
CNPV-270M 270
36.5 7.40 43.8 8.00
17 3
CNPV-275M
275 36.7 7.50 44.0 8.10
17 3
CNPV-280M 280
36.9 7.60 44.2 8.20
17 3
CNPV-285M
285 37.0 7.70 44.4 8.30
17 3
CNPV-290M 290
37.2 7.80 44.6 8.40
17 3
CNPV-295M
295 37.3 7.90 44.8 8.50
17 3
CNPV-300M 300
37.5 8.00 45.0 8.60
17 3
CNPV-305M
305 37.7 8.10 45.1 8.70
17 3
CNPV-310M 310
37.9 8.18 45.2 8.80
17 3
CNPV-315M
315 38.1 8.25 45.3 8.90
17 3
CNPV-320M 320
38.3 8.35 45.4 8.95
17 3
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 9 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
Module
Series
Model
Dimensions
(mm)
Weight
(kg)
Electrical Performance @ STC
Max-System
Voltage
(VDC)
Max-Series
Fuse (A)
Recommended Max.
Module Number
P
max
(Wp)
V
Pm
(V)
I
Pm
(A)
V
OC
(V)
I
SC
(A)
In Series
In Parallel
54p
cs 15
6×
15
6mm
SP
V
Modul
e-B
la
ck
(Mon
o-C
rys
ta
lli
ne Sili
co
n)\
CNPV-190MB-54
1482×992×35
18
190 26.6
7.15
32.6 7.90
IE
C
612
15/
IE
C
6
1
7
3
0
:1
00
0V
D
C
20
23 3
CNPV-195MB-54 195
26.9
7.25
32.8
8.00
23 3
CNPV-200MB-54 200
27.0
7.40
33.0
8.10
23 3
CNPV-205MB-54 205
27.2
7.55
33.2
8.20
23 3
CNPV-210MB-54 210
27.4
7.65
33.4
8.30
23 3
CNPV-215MB-54 215
27.6
7.80
33.6
8.40
23 3
CNPV-220MB-54 220
27.7
7.95
33.7
8.50
23 3
CNPV-225MB-54 225
27.8
8.10
33.8
8.60
23 3
CNPV-230MB-54 230
28.0
8.20
33.9
8.70
23 3
CNPV-235MB-54 235
28.3
8.30
34.0
8.80
23 3
CNPV-240MB-54 240
28.7
8.35
34.1
8.85
23
3
60p
cs 15
6×
15
6mm
SP
V
Modul
e-B
lac
k
(Mon
o-C
rys
ta
lli
ne Sili
co
n)
CNPV-220MB
1650×992×35 20
220 29.7
7.40
36.8 8.00
20
21 3
CNPV-225MB 225
30.0
7.50
37.0
8.10
21 3
CNPV-230MB 230
30.3
7.60
37.2
8.20
21 3
CNPV-235MB 235
30.7
7.65
37.5
8.30
21 3
CNPV-240MB 240
30.8
7.80
37.6
8.40
21 3
CNPV-245MB 245
30.9
7.93
37.7
8.50
21 3
CNPV-250MB 250
31.0
8.05
37.8
8.60
21 3
CNPV-255MB 255
31.3
8.15
37.9
8.70
21 3
CNPV-260MB 260
31.5
8.25
38.0
8.80
21 3
CNPV-265MB 265
31.7
8.35
38.1
8.90
21 3
72p
cs 15
6×
15
6mm
SP
V
Modul
e-B
lac
k
(Mon
o-C
rys
ta
lli
ne Sili
co
n)
CNPV-255MB
1965×992×40 24
250
35.9 7.10 43.2 7.70
20
17 3
CNPV-260MB 260
36.1 7.20 43.4 7.80
17 3
CNPV-265MB 265
36.3
7.30
43.6
7.90
17 3
CNPV-270MB 270
36.5 7.40 43.8 8.00
17 3
CNPV-275MB 275
36.7
7.50
44.0
8.10
17 3
CNPV-280MB 280
36.9 7.60 44.2 8.20
17 3
CNPV-285MB 285
37.0
7.70
44.4
8.30
17 3
CNPV-290MB 290
37.2 7.80 44.6 8.40
17 3
CNPV-295MB 295
37.3
7.90
44.8
8.50
17 3
CNPV-300MB 300
37.5 8.00 45.0 8.60
17 3
CNPV-305MB 305
37.7
8.10
45.1
8.70
17 3
CNPV-310MB 310
37.9 8.18 45.2 8.80
17 3
CNPV-315MB 315
38.1
8.25
45.3
8.90
17 3
CNPV-320MB 320
38.3 8.35 45.4 8.95
17 3
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 10 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
Module
Series
Model
Dimensions
(mm)
Weight
(kg)
Electrical Performance @ STC
Max-System
Voltage
(VDC)
Max-Series
Fuse (A)
Recommended Max.
Module Number
P
max
(Wp)
V
Pm
(V)
I
Pm
(A)
V
OC
(V)
I
SC
(A)
In Series
In Parallel
5
4
p
cs
1
56×
156
mm
SPV Modu
le
(P
ol
y-
Cr
yst
a
ll
ine S
il
ico
n)
CNPV-190P-54
1482×992×35
18
190 26.2 7.25 32.7 7.95
IEC6
121
5/
IEC6
173
0:
100
0VD
C
20
23 3
CNPV-195P-54
195 26.5 7.35 32.9 8.05
23 3
CNPV-200P-54 200
26.7
7.5
33.1
8.15
23 3
CNPV-205P-54
205 26.9 7.63 33.3 8.25
23 3
CNPV-210P-54
210 27.1 7.75 33.5 8.35
23 3
CNPV-215P-54
215 27.4 7.85 33.7 8.40
23 3
CNPV-220P-54
220 27.7 7.95 33.9 8.45
23 3
CNPV-225P-54
225 28.1 8.00 34.1 8.50
23 3
CNPV-230P-54
230 28.4 8.10 34.3 8.55
23 3
CNPV-235P-54 235
28.6
8.20
34.5
8.65
23 3
6
0
p
cs
1
56×
156
mm
SPV Modu
le
(P
ol
y-
Cr
yst
a
ll
ine S
il
ico
n)
CNPV-210P
1650×992×35 20
210 29.2 7.20 36.4 7.80
20
21 3
CNPV-215P
215 29.5 7.30 36.6 7.90
21 3
CNPV-220P
220 29.8 7.40 36.8 8.00
21 3
CNPV-225P
225 30.1 7.50 37.0 8.10
21 3
CNPV-230P
230 30.3 7.60 37.2 8.20
21 3
CNPV-235P
235 30.5 7.70 37.3 8.30
21 3
CNPV-240P
240 30.8 7.80 37.4 8.40
21 3
CNPV-245P
245 31.0 7.90 37.5 8.50
21 3
CNPV-250P
250 31.2 8.00 37.6 8.55
21 3
CNPV-255P
255 31.3 8.15 37.7 8.60
21 3
CNPV-260P
260 31.5 8.25 37.8 8.65
21 3
CNPV-265P
265 31.7 8.35 37.9 8.70
21 3
7
2
p
cs15
6×
156
mm
SPV Modu
le
(P
ol
y-
Cr
yst
a
ll
ine S
il
ico
n)
CNPV-250P
1965×992×40 24
250
35.8 7.00 43.4 7.60
20
17 3
CNPV-255P
255 36.0 7.10 43.6 7.70
17 3
CNPV-260P 260
36.2 7.20 43.8 7.80
17 3
CNPV-265P
265 36.4 7.30 44.0 7.90
17 3
CNPV-270P 270
36.6 7.40 44.2 8.00
17 3
CNPV-275P
275 36.7 7.50 44.4 8.10
17 3
CNPV-280P 280
36.9 7.60 44.6 8.20
17 3
CNPV-285P
285 37.0 7.70 44.8 8.30
17 3
CNPV-290P 290
37.2 7.80 45.0 8.40
17 3
CNPV-295P
295 37.4 7.90 45.1 8.45
17 3
CNPV-300P
300 37.6 8.00 45.2 8.50
17 3
CNPV-305P
305 37.7 8.10 45.3 8.55
17 3
CNPV-310P
310 38.0 8.15 45.4 8.60
17 3
CNPV-315P
315 38.2 8.25 45.5 8.65
17 3
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 11 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
Module
Series
Model
Dimensions
(mm)
Weight
(kg)
Electrical Performance @ STC
Max-System
Voltage
(VDC)
Max-Series
Fuse (A)
Recommended Max.
Module Number
P
max
(Wp)
V
Pm
(V)
I
Pm
(A)
V
OC
(V)
I
SC
(A)
In Series
In Parallel
5
4
p
cs
1
56×
156
mm
SPV Modu
le-B
lack
(P
ol
y-
Cr
yst
a
ll
ine S
il
ico
n)
CNPV-190PB-54
1482×992×35
18
190 26.2 7.25 32.7 7.95
IEC6
121
5/
IEC6
173
0:
100
0VD
C
20
23 3
CNPV-195PB-54
195 26.5 7.35 32.9 8.05
23 3
CNPV-200PB-54
200 26.7 7.50 33.1 8.15
23 3
CNPV-205PB-54
205 26.9 7.63 33.3 8.25
23 3
CNPV-210PB-54
210 27.1 7.75 33.5 8.35
23 3
CNPV-215PB-54
215 27.4 7.85 33.7 8.40
23 3
CNPV-220PB-54
220 27.7 7.95 33.9 8.45
23 3
CNPV-225PB-54
225 28.1 8.00 34.1 8.50
23 3
CNPV-230PB-54
230 28.4 8.10 34.3 8.55
23 3
CNPV-235PB-54
235 28.6 8.20 34.5
8.65
23 3
6
0
p
cs
1
56×
156
mm
SPV Modu
le-B
lack
(P
ol
y-
Cr
yst
a
ll
ine S
il
ico
n)
CNPV-210PB
1650×992×35 20
210 29.2 7.20 36.4 7.80
20
21 3
CNPV-215PB
215 29.5 7.30 36.6 7.90
21 3
CNPV-220PB
220 29.8 7.40 36.8 8.00
21 3
CNPV-225PB
225 30.1 7.50 37.0 8.10
21 3
CNPV-230PB
230 30.3 7.60 37.2 8.20
21 3
CNPV-235PB
235 30.5 7.70 37.3 8.30
21 3
CNPV-240PB
240 30.8 7.80 37.4 8.40
21 3
CNPV-245PB
245 31.0 7.90 37.5 8.50
21 3
CNPV-250PB
250 31.2 8.00 37.6 8.55
21 3
CNPV-255PB
255 31.3 8.15 37.7 8.60
21 3
CNPV-260PB
260 31.5 8.25 37.8 8.65
21 3
CNPV-265PB
265 31.7 8.35 37.9 8.70
21 3
7
2
p
cs15
6×
156
mm
SPV Modu
le-B
lack
(P
ol
y-
Cr
yst
a
ll
ine S
il
ico
n)
CNPV-250PB
1965×992×40 24
250
35.8 7.00 43.4 7.60
20
17 3
CNPV-255PB
255 36.0 7.10 43.6 7.70
17 3
CNPV-260PB 260
36.2 7.20 43.8 7.80
17 3
CNPV-265PB
265 36.4 7.30 44.0 7.90
17 3
CNPV-270PB 270
36.6 7.40 44.2 8.00
17 3
CNPV-275PB
275 36.7 7.50 44.4 8.10
17 3
CNPV-280PB 280
36.9 7.60 44.6 8.20
17 3
CNPV-285PB
285 37.0 7.70 44.8 8.30
17 3
CNPV-290PB 290
37.2 7.80 45.0 8.40
17 3
CNPV-295PB
295 37.4 7.90 45.1 8.45
17 3
CNPV-300PB
300 37.6 8.00 45.2 8.50
17 3
CNPV-305PB
305 37.7 8.10 45.3 8.55
17 3
CNPV-310PB
310 38.0 8.15 45.4 8.60
17 3
CNPV-315PB
315 38.2 8.25 45.5 8.65
17 3
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 12 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
4-
Φ
9
×
12
INSTALLING HOLE
1581±2
948
7
5
4
4-
Φ
12 DRAIN HOLE
2-
Φ
4
GROUNDING HOLE
GROUNDING MARKING
8
09±
2
4-
Φ
4
×
6
DRAIN HOLE
4-
Φ
4
×
4
DRAIN HOLE
316.5
316.5
Section A-A
（
magnified
）
8
1.
9
35
35
900(Typical)
+
1.8
1.5
Drawing 1 Back View of 6×12-125mm- 72cell SPV Module
1 20
~
1 4
Module Length
1 20
~
1 4
Module
Length
809
158
1
809
Module
Middle Clip
End Clip
Support Rack
809
158
1
809
Module
Support Rack
M8 Screw
Mounting Drawing (with clamping clips)
Mounting Drawing (with screws)
Drawing 2 Mounting Drawing for 6×12-125×125mm 72cell SPV Module (with screws and clamping clips on long frames)
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 13 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
35
1.8
1.9
11
1.5
35
1000VD
C IP6
5
+
TUV C
E
1202
4-Φ12 DRAIN HOLE
8-Φ9×12 INSTALLING HOLE
2-Φ4 GROUNDING HOLE
992±
2
702(For normal installation)
1200(Typical)
GROUNDING MARKING
942
4-Φ4.5×4 DRAIN HOLE
140
140
1482±2
390
390
(For High wind and snow load, these two
installation holes should also be used.)
Section A-A
（magnified）
Drawing 3 Back View of 6
×
9-156
×
156mm 54cell SPV Module
1 20
~
1 4
Modu
le Len
gth
1 20
~
1 4
Mo
dule L
ength
992
148
2
992
Moudle
Middle Clip
End Clip
Support Rack
Mounting Drawing (with clamping clips)
70
2
992
148
2
992
Moudle
Support Rack
Mounting Drawing (with screws)
Screw M8
120
2
25
0
25
0
14
0
14
0
Drawing 4 Mounting Drawing for 6×9-156×156mm 54cell SPV Module (with screws and clamping clips on long frames)
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 14 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
1.9
+
35
35
1.8
1.5
990
4-Φ12 DRAIN HOLE
8-Φ9×12 INSTALLING HOLE
2-Φ4 GROUNDING HOLE
992±2
Section A-A
（magnified）
94
1
4-Φ4.5×4 DRAIN HOLE
330
330
1200(Typical)
1650±2
11
GROUNDING MARKING
Drawing 5 Back View of 6
×
10-156
×
156mm 60cell SPV Module
1 20
~
1 4
M
odul
e L
eng
t
h
1 20
~
1 4
M
odu
l
e L
e
ng
th
992
16
50
992
Moudle
Middle Clip
End Clip
Support Rack
Mounting Drawing (with clamping clips)
33
0
99
0
33
0
992
16
50
992
Moudle
Support Rack
Mounting Drawing (with screws)
Screw M8
Drawing 6 Mounting Drawing for 6×10-156×156mm 60cell SPV Module
(with screws and clamping clips on long frames)
TECHNICAL SPECIFICATION
TITLE:
IEC INSTALLATION INSTRUCTION
MANUAL FOR THE CRYSTALLINE
SOLAR PHOTOVOLTAIC MODULE
SPEC. NO.:
CNPV-PS-M-S0010-IEC
REVISION: J
EFFECTIVE DATE:
July 2012
AUTHOR(S):
Bypina Veerraju Chaudary, Yang Xiaowu
Page 15 of 15
CNPV Dongying Solar Power Company Limited,
Shengli Industry Park, Dongying City, Shandong Province 257000, PRC
http//www.cnpv-power.com E-mail:
marketing@cnpv-power.com
Tel: +86-546-7795555, Fax: +86-546-7795777
+
1965±2
1177
94
1
4-R2.25×4 DRAIN HOLE
2-Φ4 GROUNDING HOLES
4-
?
9×12 INSTALLING HOLE
GROUNDING MARKING
4-R6 DRAIN HOLE
Section A-A
（
magnified
）
11
394
394
35
40
2.0
99
2±
2
1200(Typical)
1.8
1.5
Drawing 7 Back View of 6
×
12-156
×
156mm 72cell SPV Module
1 20
~
1 4
M
odu
le L
eng
th
1 20
~
1 4
Mod
ule
Len
gth
992
19
65
992
Module
Middle Clip
End Clip
Support Rack
Mounting Drawing (with clamping clips)
39
4
11
77
394
992
19
65
992
Module
Support Rack
Mounting Drawing (with screws)
Screw M8
Drawing 8 Mounting Drawing for 6×12-156×56mm 72cell SPV Module
(with screws and clamping clips on long frames)