Full Text Searchable PDF User Manual
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
Magnetic GPS Tracker Manual
Model: CE-M1
Preface
Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and corre
ctly. Make sure to read this manual carefully before using this product. Please note that specification and
information are subject to changes without prior notice in this manual. Any change will be integrated in
the latest release. The manufacturer assumes no responsibility for any errors or omissions in this docume
nt.
Summary
Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor
any remote targets by SMS or internet.
Applications
1. Vehicle rental / Fleet management etc
2. Container/cargo/asset tracking
3.
Hardware Description
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
4.
Content Specs.
Content Specs.
Dim.
120mm x 65mm x 35mm
Weight 305g
Network GSM/GPRS
Band 850/900/1800/1900Mhz
GPS chip
UBLOX
GPS sensitivity
-159dBm
GPS accuracy
5m
Time To First Fix
Cold status 35-80s
Warm status 35s
Hot status 1s
Car charger
12-24V input
5V output
Wall charger
110
－
220V input
5V output
Battery
Chargeable changeable 3.7V 10000mAh Li-ion battery
Standby 90
days
Storage Temp.
-40°C to +85°C
Operation Temp.
-20°C to +55°C
Humidity 5%--95%
non-condensing
5
Userage:
5.1 SIM card installation
1. Open the rubber plug
Insert the GSM SIM card.
3. Close the rubber plug.
5.2 Battery and Charger
Do charge the battery to capacity in 8 -12 hours for first time. Please use the battery and charger
provided by the manufacturer. This unit adopts built-in Li-ion battery, and full battery can standby
120days. After first use, the battery usually should be charged fully in 5--8 hours.
Cautions:
a: For it’s Li-ion battery, which contains harmful chemicals and may burst, please don’t bump, puncture
it violently and keep it off fire.
b: Please charge the battery in time to keep it working normally.
5.3Start up
Put the SIM card and battery in place.
Turn on the unit outdoor by Pushing the button to“On”the indicator is on.
For first use, please initialize the unit and restore it to default setting. (Please refer to 5.5 for instruction.)
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
In 10 or 40 seconds, the unit will begin to work and acquire the GSM signals as well as the GPS signals.
The indicator will keep flashing every 3 seconds when the unit has received the signals.
When this unit receives GPS signals normally, you can use it and do any setting as the instructions of
this manual.
5.4
LED light meaning
green LED for GPRS working status
Status of indicator
Meaning
Slow flash (flash 1s after every 2s)
GSM / GPRS conversation start
Continuously in bright status
No GPRS signal
Green Led off
Device fault or sleep
Blue LED for GPS working status
Status of indicator
Meaning
Slow flash (flash 1s after every 2s)
GPS location successful
Continuously in bright status
Searching GPS signal
Blue led off
Device fault or dormant
Red LED for power charging status
5.5 Initialization
Send “begin+password” in SMS to the unit, it will reply “begin ok” and initialize all the settings.
(Default password: 123456)
For example, send SMS“ begin123456” to the tracker via a cell phone, If succeeded,
it will reply“begin ok”.
5.5 Change the password
5.5.1 Set Password: Send sms: “password+old password+space+new password” to the unit to change the
password.
For Example, please send sms: “ password123456 000000” to terminal device, it will reply sms:
“password OK”. New password 000000 changed in success.
5.5.2 Be sure keep the new password in mind, you have to upload the software to restore the original
setting in case of losing the new password.
5.5.3 Make sure the new password is in 6 digits Arabic numbers, or the tracker can not recognize the
password.
Status of indicator
Meaning
Red led on all the time
Charging
red led flash
Low battery
red led off
Full battery or charged full
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
5.5.4 Make sure that all the symbol“+”in sms commends is just for quick understanding, which don’t
need to enter “+” in SMS, and “space” means press the spacebar button of the cell phone.
5.6 Authorization
5.6.1 Send SMS
：
“ admin+password+space+cell phone number” to set up a authorized number. The
other authorized numbers should be set by the first authorized number. If the number is successfully
authorized, the unit will reply “admin ok!” in SMS.
Note: should use country code, for example: 008615598989898.
5.6.2 Send SMS
：
“ noadmin+password+space+authorized number” to delete the authorized number.
5.6.3, Two ways to get a Google map link:
5.6.3.1, Call the device, it will hang up the call, and reply a SMS with real time position google map
link.(Only valid by Admin number.)
5.6.3.2, Send command: “where”, it will reply a google map link.
Note:
Google link: click link, there is map when positioning ok, no map means no position.
V:A GPS signal ok. V:V no GPS signal
2016-03-17 09:56:48: the last time receive GPS signal.
Spd:000km/h: the speed of tracker ran.
Bat:6 battery level
（
the range is from 1 to 9
）
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
ID:4209512755: ID code of device(used for connect tracking website or APP)
S31G00
；
plmn
：
46000 GSM operator data
Lac
：
9724
，
cellid:5020 LBS data.
5.7 Monitor (Voice Surveillance)
5.7.1 The command to switch between Track and Monitor are “tracker” and “monitor ”.
5.7.2 The default mode is “track” (Track mode).
5.7.3 Send SMS “monitor+password” to the unit, and it will reply “monitor ok!” and switch to
“monitor” mode.
5.7.4 Send SMS “tracker+password” to the unit, it will reply “tracker ok!” and restore to “track” mode.
5.8 Movement alert
5.8.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can send SMS:
“move+password” to the unit, then the unit will reply “move ok!”. In case of such a movement
（
the unit
default distance is 500M
）
, it will send SMS “Move ALARM+ Latitude and longitude” to the
authorized number
5.8.2 Cancel: Send SMS:” nomove+password” to deactivate the movement alert, tracker will reply
“nomove ok”.
5.9 Overspeed alert:
5.9.1 Set up: Send SMS: “speed+password+space+080” to the unit (suppose the speed is 80km/h), and it
will reply “speed ok!”. When the target moves exceeding 80 km/h, the unit will send SMS :”speed
ALARM !+ Google map link” to the authorized numbers.
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
5.9.2 Cancel: Send SMS “nospeed+password” to deactivate the overspeed alarm, tracker will reply
“nospeed ok”.
Remark: The recommended speed should be not less than 50km/h. For below that rate, it will be effected
the accuracy by gps signals drift etc.
5.10 Low battery alert
When GPS device battery is going to be about 3.7V, it will send SMS: “bat:l” at 30 minutes interval.
5.11 Terminal (local) Time Setting
Send SMS “time+space+zone+password+space+local time”.
For example, Send SMS “time zone123456 8” (time zone of China).
If the local time zone is negative as “-3”, then it should set as SMS: “time zone123456 -3”.
5.12 Dropped Alert.
When device have been attracted on metal 15 seconds after ( the Dropped button have been pressed 15
seconds ) ,if it device was dropped , it would alarm to the admin number by SMS or calling .
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
There are 3 ways alarm as below:
5.12.1, If need a call alarm, send command: SOS1
5.12..2, If need a SMS alarm, send command: SOS2
5.12.3, If need both SMS and Call alarm, send command: SOS3 (Default set)
If need close the alarm, send command: SOS0
5.13 Shock alert
Note: It is effective sending by authorized number
Send SMS command “shock+password”, the unit will reply “shock ok.”
Cancel: Send SMS command “noshock+password”, the unit will reply “noshock ok.”
6
Three working mode.
6.1 Continuous working + sleeping mode. (Default set)
The tracker is continuous working, when it stopped over 5 minutes, it will sleeping, GPS closed, LED
light closed, any vibration or command will wake up it.
Command: sleep123456 shock
If ok, it reply: sleep shock ok
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
6.2 Single tracking mode.
On normal status, when the unit stopped over 5 minutes, it will change to sleeping mode, on this mode,
GPS and LED light both closed, the power consumption is 4mah/h only. When it get any command or
been moved, it will wake up and start GPS locating automatically.
Note:
1, Single working time can be set, the unit is “minute”
2, If the first position SMS the tracker send to the admin number is under no GPS signal condition (V:V),
it will send again a (V:A) position SMS when GPS signal covered.
Command: sleep123456 time5
Reply: sleep time ok
6.3 No sleep mode.
The tracker continuous working without sleeping.
Command: sleep123456 off
Reply: sleep off ok.
SHENZHEN CNCOTE TECHNOLOGY CO.,LTD
Website:
www.cncote.com
Attn: Jack Foo,
Skype, cncote01, whatsapp, 008613480148499, email,
jackfoo168@gmail.com
---------------------------------------------------------------------------------------------------
7
Other command list
.
7.1 Restore factory settings
Note: It is effective sending by authorized number
Send SMS command “format”, the unit will reply “The tracker will immediately restore the factory
settings. All previous settings will be canceled.”
7.2 Restart the tracker
Command: RST
7.3 GPRS setting
User must send SMS via cell phone to set up IP, port and APN before starting GPRS.
7.4 Setting up APN
7.4.1 APN standards for Access Point Name and differs from country to country. For more information
about the local APN, inquire with your local GPRS network operator.
7.4.2 Text the tracker a SMS “apn+password + Space + your local APN” via a cell phone and if
succeeded in setup, the tracker will return the message “apn ok”.
7.4.3 e.g. send SMS command “apn123456 cmnet”. If succeeded, “apn ok” is returned by the tracker in
SMS.
Notes: 123456 refer to password of tracker and CMNET is the APN of China Mobile (One of GSM
Operator in china).
7.5 Set IP Send SMS command
：
adminip123456 119.145.40.64 9881 If succeeded, “adminip ok”
8
Cautions
8.1 Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circu
8.2 Don’t use & store the unit in dusty places.
8.3 Don’t put the unit in overheated or overcooled places.
8.4 Handle carefully. Don’t vibrate or shake it violently.
8.5 Clear the unit with a piece of dry cloth. Don’t clean in chemicals, detergent.
8.6 Don’t paint the unit, this may cause some foreign materials left in between the parts.