Full Text Searchable PDF User Manual
1
Operation Manual
<
English version
>
Thank you very much for purchasing
LDU
series printer
17
th
April, 2015
Version: V1
.
0
In order to use this product correctly and safely and understand this product’s
capability, please read this manual carefully.
Forbidden to fully or partially copy this manual.
This manual is subjected to change without notice.
Please contact us if you find any mistakes.
2
Table of Contents
Chapter 1: Safety Precaution…………………………………………..… 3
Chapter 2: Preparation and Procedures for Assembling…………….…5
Chapter 3: Machine Structure and Accessories…………………………7
Chapter 4: Technical Specification……………………………………....10
3
1.1
Important Safety Measures
Please read the following instructions before using the printer. Follow cautions and instructions which are labeled
on the printer:
1)
Do NOT block the opening on the top of the printer.
2)
Do NOT insert any object into the printing platform. Prevent spilling liquid onto the printer.
3)
ONLY 220V can be applied.
4)
Connect all the power cord to a single socket extension. Avoid sharing the socket with the devices which will
be on and off frequently.
5)
Avoid using the socket with self-timer control and with the switch on the wall.
6)
Keep your computer away from any device which will release electro-magnetic field, such as wireless phone.
7)
Do NOT use damaged power cord.
8)
If using an extra power cord, keep in mind that the total ampere of this device does not exceed the assigned
ampere of the power. Also, the total ampere of all the device which connect to single socket cannot exceed
the assigned ampere.
9)
Do NOT try to repair the printer.
When encounter the following circumstance, disconnect the power and contact your local distributor for
support:
1)
Power cord or plug is damaged;
2)
Liquid is spilled onto the printer;
3)
The printer fells down or the surface is broken;
4)
Printer does not run normally.
Chapter 1
Safety Precaution
4
1.2 Handling Printer Caution
1) Do NOT move the carriage when the power is on.
2) Always use the power switch to turn on or off the printer. Do NOT try to remove the data cable or the power
cord when the machine is on.
3) Make sure the carriage is stabilized in the origin position during transport.
1.3 Handling Ink Tank Caution
1) Please store ink tanks at the place where children cannot reach. Do NOT let children touch the ink tank.
2) If ink is spilled into eyes, immediately wash with water and see your doctor.
3) Do NOT shake the ink tank, this may cause leakage.
4) Please often check the ink content in main ink tank, avoid unnecessary loss due to lack of ink.
5) Please often check the waste ink tank and replace it in time when it becomes full.
1.4 Printer Installation Site
1) Place the printer on a level floor otherwise it will not operate normally.
2) Avoid placing the printer in the area with huge change of temperature and humidity. Do NOT expose the
printer to direct sunlight or heat. Avoid placing the printer in any possible shaking or vibrating area.
3) Leave enough space around the printer to ensure normal ventilation.
4) Place the printer close to the power socket so that power cord can be removed and plugged easily.
Chapter 1
Safety Precaution
5
2.1 Environment Requirement
Keep the room temperature between 20—30
℃
, and the humidity between 40—60%. Air conditioner and
humidifier may require. Keep a distance from strong radiation field. The floor must be level.
Site Requirement
：
2.2 Electrical requirement
The printer only supports AC 220V. A transformer is needed if the area is using AC110V
The printer must be well grounded
(the grounded voltage should be less than 0.3V, and the
grounded resistance should be less than 3
Ω)
.
UPS and voltage stabilizer is highly recommended.
Note
：
3.2m Heater:
1980W (9A)
、
Printer:
550W (2.5A)
Note: The total power consumption of the machine cannot be higher than the assigned power on the socket.
Leave at least 900mm of space around the machine.
L
：
4680mm
Chapter 2
Preparation and Procedures for Assembling
900mm
L
H
：
1225mm
W
：
920mm
900mm
6
2.3
Procedures of Assembling
1) Move the packing box to the working site and avoid strong shaking.
2) Disassemble the wooden packing box from top to bottom. Check whether the parts are complete or not
according to the packing list.
3) Lift the printer out by a forklift, and move it to the installation site.
4) Check if the printer is level.
5) Get rid of all the parts that stabilize the carriage holder, and install all the spare parts.
6) Move the carriage to the left of printer, then move back to the right manually. During this process, checks if
there are abnormal resistance and carefully inspect the belt & the encoder sensor are situated in proper
position.
7) Ground the printer. The grounded voltage should not be more than 0.3V, and the grounded resistance should
be less than 3Ω.
8) Connect the USB cable between printer and computer. Check if the wires and data cables are plugged in
properly.
9) Install the output and the rip software.
10) Turn on the printer, the carriage will automatically reposition. Keep your hand on the emergency button for
turning off the printer if problem happens suddenly.
11) Send a file to print to test the condition of the printer.
12) Install the printhead, dampers. Connect the damper to the Flush, click the Clean button to choose Depth
clean mode on the software, clean the dampers and the printhead at the same time.
13) Install the ink to the cartridge; fill ink for the first time by using Depth clean.
14) Print nozzle checking and observe the condition of printheads. It is recommended to keep a copy of the test
for reference in the future.
15) Printhead alignment.
16) Start to Print.
Chapter 2
Preparation and Procedures for Assembling
7
3.1 Machine Structure
：
（
6
）
Rear heater
（
7
）
Middle heater
（
8
）
Front heater
（
9
）
Alloy-aluminum Platen
(10)
(8)
(7)
Chapter 3
Machine Structure and Accessories
(6)
(9)
（
1
）
Left machine box
（
2
）
Cover
（
3
）
Right machine box
（
4
）
Control panel
（
5
）
Feeding & Take-up sensor
(1)
(2)
(3)
(4)
(5)
（
10
）
Feeding System
8
3.2 Name and Function of the Controlling Parts
:
（
Chapter 3
Machine Structure and Accessories
（
1
）
Heater safety switch
（
2
）
Printer safety switch
（
3
）
Heater main switch
（
4
）
Printer main switch
（
5
）
Heater power socket
（
6
）
Printer power socket
（
7
）
USB data port
（
8
）
Vacuum switch
（
9
）
Platform LED switch
（
10
）
Lamp
（
11
）
Emergency stop
（
2
）
（
6
）
（
5
）
（
4
）
（
1
）
（
3
）
（
7
）
（
9
）
（
8
）
（
10
）
（
11
）
9
3.3 Ink Supply System
：
Chapter 3
Machine Structure and Accessories
（
1
）
K Cartridge
（
2
）
C Cartridge
（
3
）
M Cartridge
（
4
）
Y Cartridge
（
1
）
（
2
）
（
3
）
（
4
）
（
1
）
Elevating Capping station
（
2)(3
）
Ink pump
(4)(5) Cap
（
6
）
（
7
）
Wiper
（
8
）
Up limit switch
（
9
）
Elevating motor
Dual printhead capping system
吸墨装置
（
7
）
（
5
）
（
1
）
（
6
）
（
4
）
（
9
）
（
3
）
（
2
）
（
8
）
10
～
END
～
Specification
Model
LDU
Max. printing width
3200mm
1880mm
Max. media width
3300mm
1880mm
Printhead
Epson DX5
Number of printhead
1 / 2
Ink
Type
UV Ink
Color
4 colors (C, M, Y, K)
Volume
1 Liter for each cartridge
Ink supply system
Cartridge
Media
Width
3200mm
1880mm
Type
Vinyl, Banner, Film, PS Board, KT Board, PVC Foam Board,etc
Feeding System
Equipped (Max. weight: 10kg)
配备
(
最大负重
40kg)
Ph. Cleaning System
Auto cleaning
Heating System
Back, middle, front heater
Clamp
Equipped
Data Transfer
USB2.0
Printhead height
Adjustable distance from 2mm~10mm
Input Voltage
AC 220V/230V
，
50Hz/60Hz
Printer
Dimension/Weight
L4700xW920xH1225mm/304Kg
Package
Dimension/Weight
L4790xW1100xH940mm /547Kg
Chapter 4
Technical Specification