Full Text Searchable PDF User Manual
Owner’s Manual
Keep with machine for reference
M O D E L E S T
INSTALLATION & OPERATION
Rev 1.04
C M A D I S H M A C H I N E S
1 2 7 0 0 K N O T T A V E N U E
GARDEN GROVE, CALIFORNIA 92841
8 0 0 - 8 5 4 - 6 4 1 7
F A X 7 1 4 - 8 9 5 - 2 1 4 1
www.cmadishmachines.com
T
ABLE OF
C
ONTENTS
Model EST
1.
SPECIFICATIONS .........................................................................................2
1.1
EST................................................................................................................................................. 2
2.
GETTING STARTED .....................................................................................3
2.1.
I
NTRODUCTION TO THE
EST............................................................................................................ 3
2.2.
R
ECEIVING AND
I
NSTALLATION
...................................................................................................... 4
2.2.1.
Electrical ................................................................................................................................ 4
2.2.2.
Plumbing................................................................................................................................. 4
2.2.3.
Connecting the Scrap Accumulator and Drain....................................................................... 5
3.
OPERATION..................................................................................................6
3.1.
I
NITIAL
S
ETUP
................................................................................................................................. 6
3.2.
S
TARTUP
P
ROCEDURES
................................................................................................................... 7
3.3.
Q
UICK SERVICE GUIDE
..................................................................................................................... 8
4.
ADDENDUM FOR MACHINES INSTALLED IN THE CITY OF CHICAGO
........9
5.
ELECTRICAL DIAGRAM ............................................................................10
www.cmadishmachines.com
1. Specifications
1.1 EST
WATER CONSUMPTION
PER RACK
1.25 GAL.
(4.73 L)
PER HOUR
46.2 GPH.
(174.9 LPH)
OPERATING CYCLE
WASH TIME-SEC.
53
53
RINSE TIME-SEC.
30
30
DWELL TIME-SEC.
7
7
TOTAL CYCLE
90 SEC.
90 SEC.
OPERATING CAPACITY
RACKS PER HOUR
37
37
WASH TANK CAPACITY
1.25 GAL.
(4.73 L)
PUMP CAPACITY
52 GPM
(196.8 LPM)
WATER REQUIREMENTS
REQUIRED MINIMUM TEMP.
120°F
(49°C)
RECOMMENDED TEMP.
140°F
(60°C)
WATER INLET
½”
—
DRAIN CONNECTION
2”
—
DIMENSIONS
DEPTH
25 ¾”
(65.405 cm)
WIDTH
25 ¾”
(65.405 cm)
HEIGHT 55-56”
(140-142
cm)
MAX CLEARANCE FOR DISHES
17”
(43.18 cm)
STRANDARD RACKS
19 ¾” x 19 ¾”
(50 x 50 cm)
ELECTRICAL RATING
VOLTS
(60-Hz)
AMPS
115
16
WASH PUMP MOTOR
1 HP
SHIPPING WEIGHT
APPROXIMATE
273# (124
kg)
USA
METRIC
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
2
Getting Started
2. Getting Started
2.1.
Introduction to the EST
The EST Dishmachine is safe and easy to operate with its “Auto Start/Stop” and it’s economical
to operate—using only 1.25 gallons of water per cycle and less than 1900 watts of power when
running. The EST Dishmachine’s top mounted controls include built-in chemical pumps and a
deliming system that assures proper chemical usage. Its integrated scrap tray prevents food soil
from entering the drain system. The EST can be run at a rate of 37 racks/148 covers per hour
and its heavy-duty stainless steel construction assures long life and years of trouble free
operation.
The EST is available for straight or corner applications.
This manual is structured to provide a complete reference guide to the EST Dishmachine. It is
presented in a manner that all users will be able to comprehend and use as an effective tool in
supporting the operation and maintenance of the dishmachine. The first section explains how the
machine is packaged and what to look for when receiving the machine.
After unpacking the machine, this manual explains how to install and set up the machine for use.
Requirements are given for plumbing, wiring, and space considerations.
These attributes of the
machine are always taken into consideration by our well-trained sales representatives prior to the
order being placed
. In the manual, guidance is also given for installation to ensure that the
machine will be able to run at optimum conditions.
The Operation section of the manual may be used for instruction and procedures when required.
We make this portion of the manual easy to understand so that all levels of operators may be
able to read and comprehend the operation of the machine. The function of the machine itself is
mostly automatic and takes little training to put into full operation. The Operation section also
includes diagnostic considerations (troubleshooting) for the machine when problems occur.
The remaining sections of the manual—Parts Manual and Electrical Diagram—have the parts
lists with exploded view drawings and the wiring diagram for the machine.
CMA warranties the workmanship of the machine.
We are committed to providing the best machines and customer service in the food industry and
your feedback is welcome.
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
3
Getting Started
2.2.
Receiving and Installation
The dishwasher is shipped from the factory in a corrugated box on a wooden pallet. The
installation guidelines give a systematic procedure for setting up the machine.
Start by removing the dishmachine from the box. Remove the packaging, unwrap the machine
and check for the following components:
Inside the wash tank is a plastic bag with one control box key and a cam timer
wrench.
Tube stiffeners must be used to prevent the feed tubes from curling inside the
chemical pail and sucking air. These are located on the outside of the machine with
the chemical tubing already installed into the stiffeners. The ends of the chemical
tubing have been flared so that the tubing will not pull out of the stiffener. Red is for
detergent, white for sanitizer, and blue for rinse aid.
2.2.1. Electrical
*
The EST Dishmachine must be hard wired directly to a dedicated 115 VAC, 60Hz circuit
equipped with proper circuit protection. The main power switch is at the top-right side of the
control box.
2.2.2. Plumbing
*
The water supply connection is made with a ½” hot water line to the water supply inlet on the top
of the machine. The water supplied to the machine is recommended to be 140° F. The time
necessary to deliver water to the machine is controlled by the number four cam. This cam
provides the serviceman with the opportunity to fine tune the machine to deliver the proper
amount of water with each cycle.
The EST Dishmachine has a 2” drain. The following section explains how to connect the drain.
*
Electrical and plumbing connections must be made by a qualified person who will comply with all
available Federal, State, and Local Health, Electrical, Plumbing and Safety codes
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
4
Getting Started
2.2.3. Connecting the Scrap Accumulator and Drain
The scrap accumulator is designed to perform two basic functions:
1. It allows a method to discharge all the heavy solids out of the machine with each
wash cycle.
2. It provides accumulation capacity to allow draining the contents of one cycle
regardless of the discharge rate of the existing drain.
The drainpipe is connected to the scrap accumulator drain using a 2” no-hub connector as shown
in
Figure 2.2.3
below.
2" DRAIN
SLEEVE
2"
NO-HUB
2" DRAINPIPE
SCRAP ACCUMULATOR
HOSE
CLAMPS
Figure 2.2.3
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
5
Operation
3. Operation
3.1. Initial
Setup
All machines are equipped with switches to prime the peristaltic pumps at anytime the master
switch is "ON".
Following completion of the installation, always fill the machine with water before starting the
machine.
1. With the power “ON” hold the fill button until the water level overflows into the scrap
accumulator.
2. Check the chemical lines to the chemical containers.
a. Red: detergent line.
b. Blue: rinse agent line.
c. Clear/White: sanitizers destainer line.
3. Activate the prime switches for the three chemical pumps until product is
discharging into the machine.
4. To start the machine, close the doors - this will automatically start the machine. The
machine will run through its cycle.
5. Operate the machine one cycle and watch to ensure that the chemicals are
delivered and stop during the cycle. Remember: red tube - detergent: blue tube -
rinse: and clear/white tube - sanitizer. Check temperature at the end of the cycle for
140
°
F, 60
°
C.
The amount of product delivered by each cam is controlled by adjusting the cam’s
opening. When the micro switch rides down into the cam the peristaltic pump motor
begins to rotate. It will continue to rotate until it rides up out of the groove.
Therefore, to extend the amount of product delivered to the machine, open the
grove; to reduce the amount of product delivered to the machine, close the groove.
The cams are slip fit and a cam adjustment wrench is provided.
CAUTION:
The motors on the new peristaltic pumps may be stalled by excessive tightening of
the cover plate screws. If a peristaltic pump does not turn when the micro switch is activated,
loosen the screws on the cover plate.
Technical personnel are available during normal business hours at CMA Headquarters should
you, as an installer, have any questions please call
800-854-6417
.
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
6
Operation
3.2. Startup
Procedures
Please follow the instructions given here before each shift to assure trouble free operation.
2. Drain the water if it is cold by activating the drain switch until all the water is
out of the machine.
3. Check the drain screen and, if needed, remove it from the machine and clean
it out. After cleaning, replace it properly into the sump housing.
4. Check the wash arm spray tips. If they are clogged, clean them with a
toothpick and rinse them at the sink. Replace the wash arms.
5. Press and hold the fill switch until the water overflows into the scrap
accumulator.
6. Once a proper water level is established, check the temperature of the water
(it should be approximately 140
°
F, 60
°
C).
7. Insert the tray of dishes into the machine and close the doors. The machine
will automatically start when the doors are closed.
8. After the machine stops, raise the doors, remove the tray of dishes and allow
to dry before stacking.
If the doors are lifted during a cycle, the machine will automatically stop running.
The EST will run through the wash and rinse cycles automatically feeding the proper chemicals
and then turn itself off.
In an emergency you can turn off the machine by turning off the master switch located on the side
of the control box.
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
7
Operation
3.3.
Quick service guide
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
8
MODELS: VA AND EST
TECHNICAL ISSUE
Cause
Solution
Machine starts while doors are
open
Faulty magnetic door switch
Replace the switch, P/N 00557.55
Faulty start/fill switch
Replace the switch, P/N 03470.01
Faulty #1 micro switch (start/stop) Replace micro switch, P/N 00411.00
Continuous cycles
Faulty start/fill switch
Replace micro switch, P/N 00411.00
Faulty door switch
Replace the switch, P/N 00557.55
Delimer switch in wrong position Switch to
NORMAL
position
Wash motor runs continuously
Faulty delime switch
Replace the switch, P/N 00475.00
Faulty motor contactor
Replace contactor, P/N 00404.82
Delimer switch on wrong position Switch to
NORMAL
position
Sanitizer pump does not run
Faulty delimer switch
Replace the switch, P/N 00475.00
Faulty # 6 micro switch
Replace micro switch, P/N 411.00
Faulty sanitizer pump motor
Replace the motor, P/N 00416.00
Broken Spring
Replace spring, P/N 00105.82
Drain valve does not operate
Faulty #3 Micro switch
Replace micro switch, P/N 00411.00
Faulty drain motor
Replace drain motor, P/N 00104.82
Faulty #4 micro switch (Fill)
Replace micro switch, P/N 00411.00
Debris inside water solenoid valve Clean valve replace diaphragm kit,
P/N 00707.00
Machine does not fill
Faulty start/fill switch
Replace the switch, P/N 03470.01
Drain not closing
check function of drain sys.
Faulty water solenoid coil/valve
Replace coil/valve, P/N 00738.10 or
03603.10
Faulty check valve
Replace valve, P/N 00718.00
Water leaks out of vacuum breaker Low incoming water pressure
Increase water pressure to 20 psi
Faulty vacuum breaker kit
Replace vac. Brkr kit, P/N 03623.00
Machine only runs when start/fill
switch is depressed
Faulty #1 micro switch (start/stop) Replace micro switch, P/N 00411.00
Faulty magnetic door switch
Replace door switch, P/N 00557.55
Will not start/ nothing works
Wall breaker tripped
Reset breaker
Master on/off switch faulty or in off
position
Reset or replace switch, P/N 00471.10
Runs, but none of the other
functions engage
Faulty #2 Micro switch (cycle
reset)
Replace micro switch, P/N 411.00
Faulty ice cube relay (yellow relay) Replace relay, P/N 00636.00
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
9
4.
Addendum for Machines Installed in the City of Chicago
"All food dispensing establishments using chlorine or other approved chemical sanitizers shall, at
all times, maintain an adequate testing device."
"Dishes and other eating and drinking utensils to be washed in a dishwashing machine shall be
properly scraped and pre-rinsed and shall be stacked in racks or trays so as to avoid
overcrowding, and so as to permit the wash and rinse waters to reach all surfaces of each
utensil."
"In machine washing, multi-use eating and drinking utensils shall be washed in water containing a
suitable detergent at a temperature from 120 degrees F. to 140 degrees F. or other method
approved by the Department of Health.
"The water in the wash tank shall be changed during operation as often as is necessary to keep it
reasonably clean. An effective concentration of detergent in the wash water shall be maintained
at all times."
"Bactericidal treatment shall consist of exposure of all surfaces of dishes and utensils being
washed to a rinse of clean water, at a temperature of not less than 180 degrees F. or other
method approved by the Department of Health."
"All dishwashing machines shall maintain a flow pressure not less than 15 or more than 25
pounds per square inch on the fresh water line at the machine and not less than 10 pounds per
square inch at the rinse nozzles. A suitable gauge cock shall be provided immediately upstream
from the final rinse spray to permit checking the flow of the final rinse water. An easily readable
thermometer accurate to
±
2 degrees F. shall be provided on both the wash and rinse water lines
of the dishwashing machine which will indicate the temperature of the water solution therein."
"Dishwashing machines shall be thoroughly cleaned at least once each day. The pumps and the
wash and rinse sprays or jets shall be so designed that a forceful stream of water will reach all
surfaces of the utensils when they are properly racked. These parts shall be thoroughly cleaned
at least once each day. The pumps and the wash and rinse sprays or jets shall be so designed
that a forceful stream of water will reach all surfaces of the utensils when they are properly
racked. These parts shall be readily accessible for inspection and cleaning."
"After bactericidal treatment, utensils and containers shall be stored at a sufficient height above
the floor in a clean, dry place, protected from flies, splash, dust, overhead leakage and
condensation, and other contamination. Containers and utensils shall be inverted, covered, or
otherwise protected from contamination until used for serving."
Drain racks, trays, and shelves shall be made of non-corrodible material and shall be kept clean.
In handling containers and utensils the surfaces thereof which come in contact with food or drink
shall not be touched by the hands, except during the process of washing.
Tables for clean and dirty dishes and food shall be so arranged that the dirty dishes will be as far
removed from the food and clean dishes as may be possible.
All single-service articles and utensils shall be purchased in sanitary cartons and stored therein in
a clean, dry place until used, and after removal from the cartons, these articles shall be handled
in such a manner as to prevent contamination.
Please note the following procedures must be followed for City of Chicago
Approval:
1. All low energy models must have low-level sani alarms, both
visual and audio.
2. All models must have a City of Chicago approval data label
affixed to the machine.
3. Chlorine sanitizer must be a minimum of 100 PPM.
Electrical Diagram
5. Electrical Diagram
MODEL EST INSTALLATION & OPERATION MANUAL Rev. 1.04
Page
10