Full Text Searchable PDF User Manual
CLIPTEC 1600DPI 2.4GHZ WIRELESS OPTICAL
MOUSE - ISUTTU
This symbol identifies safety and health messages in the Product Guide and other product
Failure to properly set up, use, and care for this product can increase the risk of serious injury or
death, or damage to the device or devices. Read this guide and keep all printed guides for future
Important Safety Information
These precautions apply to all products that use rechargeable or disposable batteries. Improper
use of batteries may result in battery fluid leakage, overheating, or explosion. Released battery
fluid is corrosive and may be toxic. It can cause skin and eye burns, and is harmful
To reduce the risk of injury:
Keep batteries out of reach of children.
Do not heat, open, puncture, mutilate, or dispose of batteries in fire.
Do not mix new and old batteries or batteries of different types (for example,
carbon-zinc and alkaline batteries).
Do not allow metal objects to touch the battery terminals on the device; they
can become hot and cause burns.
Remove the batteries if they are worn out or before storing your device for an
extended period of time. Always remove old, weak, or worn-out batteries promptly and
recycle or dispose of them in accordance with Local and National Disposal Regulations.
If a battery leaks, remove all batteries, taking care to keep the leaked fluid
from touching your skin or clothes. If fluid from the batter comes into contact with skin
or clothes, flush skin with water immediately. Before inserting new batteries, thoroughly
clean the batter compartment with a damp paper towel, or follow the battery
manufacturer’s recommendations for cleanup.
Risk of explosion if battery is replaced by an incorrect
type. Use and replace only with correct size and type (alkaline, zinc-carbon,
chloride) of batteries.
Do Not Attempt Repairs
Do not attempt to take apart, open, service, or modify the hardware device or power supply.
Doing so could present the risk of electric shock or other hazard. Any evidence of any attempt to
open and/or modify the device, including any peeling, puncturing, or removal of any of the labels,
will void the Limited Warranty.
This device may contain small parts which may be a choking hazard to children under 3. Keep
small parts away from children.
Usage and Cleaning
Use in accordance with these instructions:
Do not use near any heat sources.
Only use attachments/accessories specified.
only with dry cloth.
Do not allow this product to become wet. To reduce the risk of fire or
shock, do not expose this product to rain or other types of moisture.
Some devices use adhesive tape to mount components in your workspace. DO NOT mount on
antiques, heirlooms, or other valuable or irreplaceable items. After mounting, removing the
adhesive may damage the cosmetic coating and/or leave an adhesive residue.
To avoid damaging equipment placed on the tablet stand, do not overload or bump it, causing it to
collapse or tip over.
Laser and LED Specifications
Use of controls or adjustments, or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Optical (LED) Mouse
This product has been evaluated to comply with International Standard (IEC 60825-1:2001-08)
and IEC 62471 (2006-07). This product uses LEDs that are considered Class 1 (IEC 60825-
Radio and TV Interference Regulations
If not installed and used in strict accordance with the instructions given in the printed
documentation and/or onscreen help files, the device may cause harmful interference with other
radio-communications devices (for example AM/FM radios, televisions, baby monitors, cordless
phones, etc.). There is, however, no guarantee that RF interference will not occur in a particular
To determine if your hardware device is causing interference to other radio-communications
devices, disconnect the device from your computer or remove the device’s batteries (for a battery
operated device). If the interference stops, it was probably caused by the device. If the
interference continues after you disconnect the hardware device or remove the batteries, turn the
computer off and then on again. If the interference stopped when the computer was off, check to
see if one of the input/output (I/O) devices or one of the computer’s internal accessory boards is
causing the problem. Disconnect the I/O devices one at a time and see if the interference stops.
If this hardware device does cause interference, try the following measures to correct it:
Relocate the antenna of the other radio-communications device (for example
AM/FM Radios, televisions, baby monitors, cordless phones, etc) until the interference
Move the hardware device farther away from the radio or TV, or move it to
one side or the other of the radio or TV.
Plug the computer into a different power outlet so that the hardware device
and radio or TV are on different circuits controlled by different circuit breakers or fuses.
If necessary, ask your computer dealer or an experienced radio-TV technician
for more suggestions.
Disposal of Waste Batteries and Electrical & Electronic Equipment
symbol on the product or its batteries or its packaging means that this product and any batteries it
contains must not be disposed
of with your household waste. Instead, it is your responsibility to
hand this over to an applicable collection point for the recycling of
batteries and electrical and
electronic equipment. This separate collection and recycling will help to conserve natural
prevent potential negative consequences for human health and the environment
due to the possible presence of hazardous substances
in batteries and electrical and electronic
equipment, which could be caused by inappropriate disposal. For more information about
to drop off your batteries and electrical and electronic waste, please contact your local
city/municipality office, your household
waste disposal service, or the shop where you
purchased this product.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.