CLOROX Total 360 Operator's Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

| 1

Electrostatic

Sprayer CLX1000

115VAC, 60Hz, 7.0 A

Indoor Commercial
Use Only

Operator’s

Manual

© 2016 The Clorox Company
Professional Products Division
1221 Broadway
Oakland, CA 94612
1-800-492-9729
www.cloroxtotal360.com

2 |

SAFETY NOTICES

Warnings

Safety Decal

Protective Gear

IMPORTANT SAFETY PRECAUTIONS

Power Connection

Grounding Instructions

Extension Cord

Shock/Electrical Hazard

General Safety

Chemicals

SYSTEM COMPONENTS

Clorox Total 360™ Base Unit

Clorox Total 360™ Sprayer

Nozzle

OPERATING INSTRUCTIONS

Preparing the Spray Area

Unit Operation/Setup

Sprayer Operation During Cleaning

Changing Clorox-Approved Products

After Use and Storage

MAINTENANCE

Sprayer Body

Air Filter

Peristaltic Pump

Nozzle

SPECIFICATIONS

TROUBLESHOOTING

EQUIPMENT WARRANTY

Table of Contents

| 3

SAFETY NOTICES

This manual contains information that is important for you to know
and understand before operating the Clorox Total 360™ Electrostatic
Sprayer. This information relates to protecting your safety and ensures
product reliability and performance. It is the owner’s responsibility to
ensure that all who operate this equipment read this manual.

Warnings

To help you recognize this information we use the warning symbols
below. Please read the manual carefully and pay special attention to
the symbols and warning labels. Warning labels indicate a potentially
hazardous situation which, if not avoided, could result in death or
serious injury.

WARNINGS

• Read and fully understand the Clorox Total 360™ Electrostatic

Sprayer Operators Manual prior to using the electrostatic sprayer.

• Read and fully understand Clorox-approved product labels prior to

using any liquid product with the Clorox Total 360™ Electrostatic

Sprayer.

• Clorox Total 360™ Electrostatic Sprayers are for indoor commercial

use ONLY.

• Clorox Total 360™ Electrostatic Sprayers should never be used in

a hazardous environment.

• Clorox Total 360™ Electrostatic Sprayers should never be used

in an area containing volatile chemicals. Nor should it be used in

any area containing volatile or explosive levels of gas, vapor or

particulates.

• Clorox Total 360™ Electrostatic Sprayers should never be used by

untrained personnel.

WARNINGS

PRESSURIZED EQUIPMENT HAZARD
Fluid from equipment that leaks or ruptures from a component can

splash in the eyes or on skin, causing serious injury. In order help

prevent a leak or rupture:

• Check hoses, tubes and couplings daily.

Replace worn or damaged parts immediately.

WARNINGS

PLASTIC PARTS CLEANING SOLVENT HAZARD
Many solvents can degrade plastic parts and cause them to fail,

which can lead to serious injury or property damage. In order to help

prevent against degradation:

• Use only compatible water-based solvents to

clean plastic structural pressure containing

parts.

• See technical data in this and all other

equipment instruction manuals. Read

fluid and solvent manufacturer’s SDSs and

recommendations prior to use.

WARNINGS

FIRE, EXPLOSION AND ELECTRIC SHOCK HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can

ignite or explode. To help prevent fire, explosion and electric shock:

• Electrostatic equipment must be used only by

trained, qualified personnel who understand

the requirements of this manual.

• Stop operation immediately if static sparking

occurs or you feel shock. Do not use equipment

until you identify and correct the problem.

• Use and clean equipment only in well-

ventilated area.

• Never spray a flammable chemical

(with a flashpoint less than 60˚C).

• Do not plug or unplug power cords or

turn lights on or off when flammable

fumes are present.

• Keep spray area free of debris, including solvents,

rags, gasoline or any flammable chemicals.

• Keep a working fire extinguisher in the work area.

4 |

Safety Decal

This decal is located on the top-most deck surface forward of the
bottle storage location.

WARNINGS

EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury

• Do not operate the unit when fatigued or under

the influence of drugs or alcohol.

• Use fluids and solvents that are compatible

with equipment wetted parts. See technical

data in all equipment manuals. Read fluid and

solvent manufacturer’s warnings. For complete

information about your material, request SDS

from distributor or retailer.

• Do not leave the work area while equipment

is energized.

• Turn off all equipment when not in use.
• Check equipment daily. Repair or replace worn

or damaged parts immediately with genuine

replacement parts from trusted Clorox

partners only.

• Do not alter or modify equipment. Alterations

or modifications void your Clorox Total 360™

warranty, agency approvals and create safety

hazards.

• Route hoses and power cords away from traffic

areas, sharp edges, moving parts and hot

surfaces.

WARNINGS

CHEMICAL USE HAZARD
Each chemical, such as a disinfectant, has a unique set of hazards

and needs to be handled properly to ensure worker safety.
• The Clorox Total 360™ Electrostatic Sprayer can only be used

with products that have been approved by Clorox.

Never spray

any liquid product that is not a Clorox-approved product.

The

Clorox Total 360™ Electrostatic Sprayer warranty is voided if the

Clorox Total 360™ Electrostatic Sprayer is used with products that

are not approved by Clorox. Be aware that many chemical liquids

can be harmful if they are not used properly.

• Read and understand the Clorox-approved product’s SDS and

label prior to use.

• Be aware of first aid procedures related to the product in use.
• It is a violation of Federal law to use a chemical in a manner

inconsistent with its label.

• Use personal protective equipment as detailed by the Clorox-

approved product’s SDS.

• For use with non-flammable, non-combustible and non-volatile

fluids only. Never spray a flammable chemical (flash point less

than 60˚C) .

• Insure the area being sprayed has proper ventilation.
• Store all chemicals in original containers in a cool, dry place, away

from heat and open flames.

• Do not reuse or refill a chemical container.
• To dispose of Clorox-approved products refer to product labels.

WARNINGS

PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to

help prevent serious injury.

• Recommend use of fully enclosed eyewear

protections, such as goggles, when using this

device.

• Refer to product specific Clorox Safety Data

Sheets (SDS) for any additional PPE.

| 5

Protective Gear

Personal Protective Equipment (PPE) must comply with the American
National Standards Institute, ANSI Z87.1-1989 standard if purchased
after July 5, 1994, or ANSI Z87.1-1968.

• Eye and face PPE shall be distinctly marked to facilitate identification

of the manufacturer. [1910.133(a)(4)].

• The following minimum requirements must be met by all protective

devices. Protectors shall:
- Provide adequate protection against the particular hazards for

which they are designed.

- Be of safe design and construction for the work to be performed.
- Be reasonably comfortable when worn under the designated

conditions.

- Fit snugly and not unduly interfere with the movements

of the wearer.

-  Be durable.
-  Be capable of being disinfected.
-  Be easily cleanable.
-  Be distinctly marked to facilitate identification only

of the manufacturer.

RECOMMEND USE OF FULLY ENCLOSED EYEWEAR
PROTECTIONS, SUCH AS GOGGLES, WHEN USING THIS DEVICE.
ALWAYS USE APPROPRIATE PPE, LISTED ON THE CLOROX-
APPROVED PRODUCT’S SAFETY DATA SHEET (SDS).
CLOROX SDS’S CAN BE FOUND AT
WWW.CLOROXPROFESSIONAL.COM/SDS

IMPORTANT SAFETY PRECAUTIONS

When using an electrical appliance, it is important to understand that
some circuits are electrically live, even when the power switch is in
the off position. Basic safety precautions should always be followed to
reduce the risk of burns, fire, electrical shock, injury and/or death.

Power Connection

Our power plug must be used with a 3-prong grounded outlet, rated
for no less than 15A service. Always verify before product use. This
appliance is for use on a nominal 120V/60Hz circuit with a verified
ground plug. Check with a qualified electrician to insure you have the
correct electrical service and grounding.

Grounding Instructions

This appliance must be grounded. In the event of malfunction or
breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and
ordinances. Never use an adapter with this product.

DANGER:

Improper connection of the equipment-grounding conductor

can result in a risk of electric shock. The conductor with insulation
having an outer surface that is green, with or without yellow stripes,
is the equipment-grounding conductor. If repair or replacement of
the cord or plug is necessary, do not connect the equipment-ground
conductor to a live terminal. Check with a qualified electrician
or serviceman if the grounding instructions are not completely
understood or if in doubt as to whether the appliance is properly
grounded. Do not modify the plug provided with the appliance — if
it will not fit the outlet, have a proper outlet installed by a qualified
electrician. Never use an adapter with this product.

Extension Cord

Clorox provides a 25-foot extension cord with each Total 360™
Electrostatic Sprayer and strongly recommends that you use
this approved extension cord. Make sure your extension cord is in
good condition. Inspect cords periodically and replace if damaged.
If an alternate extension cord is used, be aware that an undersized
extension cord will cause a drop in-line voltage, which could result
in loss of power, damage to the product and/or overheating.
Always use a sufficiently rated extension cord.

IMPORTANT:

Clorox recommends using a 12/3 gauge extension

cord, no longer than 100 feet (30.5m). Additionally, Clorox also
recommends the use of a GFCI (ground fault circuit interrupter) power
outlet or extension cord. When equipped on the extension cord, always
position the GFCI toward the power outlet.

6 |

Shock/Electrical Hazard

As with most electrical appliances, electrical parts are electrically live
even when the switch is off. To reduce the risk of burns, fire, electric
shock or injury:

1. Use this unit only for its intended use, as described in this manual.

2. Do not use while bathing.

3. Do not place or store unit where it can fall or be pulled into water

or other liquid.

4. If unit falls into water, unplug immediately. Do not reach into water

to retrieve.

5. Never operate this unit if it has been dropped, damaged or is

working improperly. Contact an authorized Clorox technician.

6. Keep the cord away from heated surfaces.

7. Never block the air openings of the unit or place it on a soft surface

(bed or couch), where the air openings may become blocked.

8. Never drop or insert any object into any opening.

9. Do not use with a damaged or broken power cord.

10. Never store at a temperature above 140˚F.

11. This unit may be warm when in use. Do not let heated surface

touch bare skin.

General Safety

Lack of attention to safety can result in reduced efficiency, accident,
personal injury or death. Watch for safety hazards and correct
deficiencies promptly. Use the following safety precautions as a guide
when using this machine.

1. Read the operator’s manual. Failure to do so is considered misuse

of the equipment.

2. Use the Clorox Total 360™ Electrostatic Sprayer unit only for its

intended use, as described in this manual.

3. Before operating equipment, become familiar with all caution and

warning decals affixed to the equipment.

4. Do not use the Clorox Total 360™ Electrostatic Sprayer in a

hazardous location.

5. Only trained personnel familiar with the Clorox Total 360™

Electrostatic Sprayer and Clorox-approved products should be
allowed to operate.

6. Do not allow personnel to operate the sprayer without proper

instruction or under the influence of alcohol or drugs.

7. Use an extension cord meeting or exceeding the specification

detailed in the Extension Cord section.

8. Store sprayer in a cool, dry place. Do not expose to extreme

temperatures.

9. Purge liquid line before storing the unit.

10. Be aware, even when the sprayer is off, power is still supplied

to the unit when plugged into an electrical outlet.

11. Never hang unit from cord.

12. A sprayer should never be left unattended when plugged in.

13. A resettable breaker is provided on the rear of the unit. It will trip

if the unit experiences an electrical short.

14. Always turn off sprayer after each application and before unplugging.

15. Always unplug unit from outlet when not in use or when leaving

it unattended.

16. Never unplug by pulling the cord or with wet hands. Always unplug

by grasping the plug.

17. Do not pull or carry the sprayer by the power cord.

18. Do not crimp the cord or strain it around sharp edges, as doing so

might damage the cord.

19. Do not use the Clorox Total 360™ Electrostatic Sprayer with a

damaged power cord.

20. Always thoroughly inspect product before usage.

21. Contact Clorox Total 360™ Electrostatic Sprayer support center

for any questions or concerns regarding the equipment:
1-800-492-9729.

Chemicals

The Clorox Total 360™ Electrostatic Sprayer can only be used with
products that have been approved by Clorox. The Clorox Total 360™
Electrostatic Sprayer warranty is voided if the Clorox Total 360™
Electrostatic Sprayer is used with products that are not approved by
Clorox. Be aware that many chemical liquids can be harmful if they are
not used properly.

1. Always use appropriate personal protective equipment (PPE) when

operating the Clorox Total 360™ Electrostatic Sprayer. Refer to
product SDS for proper PPE.

2. Follow the liquid product label and SDS for proper storing, handling

and disposing of any liquid products used in the Clorox Total 360™
Electrostatic Sprayer.

3. Know the length of time required by each liquid product application

before allowing people and pets to return to the sprayed area.

4. Tampering with Clorox-approved products, product containers and

the Clorox Total 360™ Electrostatic Sprayer in any form will void
customer warranty.

5. To dispose of Clorox-approved products refer to product labels.

6. If liquid products come into contact with your skin or eyes, please

refer to product label and SDS.

7. Never aim the sprayer at yourself or another person.

IMPORTANT:

Safety data sheets (SDS) are available for all liquid

products that have been approved for use in the Clorox Total 360™
Electrostatic Sprayer. These SDSs will inform you of any hazards and
precautions of which you should be aware. All employees that use the
product must be aware of and have access to the SDS. They should
also be trained and aware for their safety while working with liquid
products. It is the responsibility of the owner of the equipment to
obtain an SDS from Clorox for each chemical used.
Visit

www.cloroxprofessional.com/sds

for more information.

| 7

Nozzle

The nozzle assembly is located at the end of the sprayer. It is
composed of a spring-loaded contact, external O-ring, nozzle
cover, liquid tip and electrode. These are the only user-serviceable
components. To access the nozzle components, unscrew the nozzle
cover counterclockwise by hand. It is very important to follow all the
maintenance and cleaning procedures to ensure that the sprayer will
function optimally. After servicing nozzle, it is extremely important to
return the nozzle to its seat position and avoid overtightening.

NOTE:

As the sprayer becomes dirty from typical use, a 70% isopropyl

alcohol cleaner that is manually applied is recommended on the
outside surfaces. This discourages dripping from the nozzle.

Clorox Total 360™ Base Unit

Air Compressor

Atomizes and propels the liquid. Runs

on 115-volt power. Includes built-in

auto resetting thermal safeguard

against compressor overheating.

Non-Marking Wheels

Large wheels, for easy transport and

maneuverability, will not leave scuff

marks. Do not require inflation.

Sprayer Connect Line

Connect line consists of four

components: electrical line, liquid line,

air line and stainless steel braided

cable. The connect line connects the

sprayer to the base unit.

Air Filter

User-replaceable air filter that filters

out particles from incoming air.

Sprayer Holster

Holds the sprayer.

Adjustable Handle

Handle position is raised, lowered and

rotated by the two button snaps.

Peristaltic Pump

Provides liquid up to sprayer.

Circuit Breaker

User resettable circuit breaker and will

only trip if a short occurs in the base unit.

Main Power

Switch

Powers system to a ready state.

1-Gallon Chemical

Containers

Chemical containers (not included

with equipment).

Extension Cord Holder

Located at the rear of the unit for

extension cord storage.

Frame

Stainless steel frame and hardware

design for long-term durability.

Pump Purge

Switch

Purges product from liquid line.

(press to purge)

Handle Adjust

Buttons

Adjusts handle height.

(squeeze to adjust)

Sprayer Electrical

Disconnect

Electrical connection for Sprayer.

Clorox Total 360™ Sprayer

Trigger Button

1-click functionality / operates the
sprayer/device.

Instrument Panel

Indicates the power, sprayer and

electrostatics are on.

Nozzle Cover

Located on the front of the sprayer.

Sprayer Grip

Handle position for ambidextrous use.

Sprayer Connect

Connect line consists of four components,

electrical line, liquid line, air line and

stainless steel braided cable.

SYSTEM COMPONENTS

The patented Clorox Total 360™ Electrostatic Sprayer was engineered
with the end-user in mind. It is a durable, highly mobile and incredibly
effective for electrostatic delivery.

8 |

5. After spraying, keep the area closed to the public based

on product SDSs.

6. Remove the closed sign from the door once the reentry time

has expired.

Changing Clorox-Approved Products

1. Stop spraying the Clorox Total 360™ Electrostatic Sprayer.

2. Disconnect the bottle connection from the Clorox-approved

product that is to be changed and remove from the sprayer.
Cap the removed product if it is being stored.

3. Purging the Clorox Total 360™ Electrostatic Sprayer: Depress into

an inconspicuous corner, container or drain. Spray the Clorox Total
360™ Electrostatic Sprayer for about 20 seconds to purge the system.

4. Chose the appropriate Clorox-approved product for cleaning,

sanitizing or disinfecting.

5. Mount desired Clorox-approved product on Clorox Total 360™

Electrostatic Sprayer base and strap into place. Ensure that the
bottles are positioned with the opening facing up and the opening
facing the dispensing tubes.

6. Unscrew the lid on the Clorox-approved products of your

choice and connect the Clorox Total 360™ Electrostatic Sprayer
dispensing cap to the bottle. Be sure the cap is screwed all the way
down, do not overtighten.

7. Priming the Clorox Total 360™ Electrostatic Sprayer: Depress into

an inconspicuous corner, container or drain. Spray the Clorox Total
360™ Electrostatic Sprayer for about 20 seconds to generate a
steady flow of solution.

After Use and Storage

1. Stop spraying the Clorox Total 360™ Electrostatic Sprayer.

2. Disconnect the bottle connection from the Clorox-approved

product that is to be changed and remove from the sprayer. Cap
the removed product if it is being stored.

3. Purging the Clorox Total 360™ Electrostatic Sprayer: Depress into

an inconspicuous corner, container or drain. Spray the Clorox Total
360™ Electrostatic Sprayer for about 20 seconds to purge the system.

4. Turn off the unit. Blue indicator light on the instrument panel and

base of the unit should no longer be illuminated.

5. Unplug the Clorox Total 360™ Electrostatic Sprayer from wall.

6. Wrap cord on cord holder on the Clorox Total 360 base unit.

8. Store in a safe, dry place.

Preparing the Spray Area

1. Clean gross filth by using standard manual cleaning protocols.

2. Close the room to the general public for cleaning. Place signs

or warning indicators on doors that indicate no one should enter
the room.

3. Power off any sensitive electrical devices but do not unplug them.

Unit Operation/Setup

1. Choose the appropriate Clorox-approved product for cleaning,

sanitizing or disinfecting.

2. Mount desired Clorox-approved product on Clorox Total 360™

Electrostatic Sprayer base and strap into place. Ensure that the
bottles are positioned with the opening facing up and the opening
facing the dispensing tubes.

3. Unscrew the lid on the Clorox-approved product of your choice and

connect the Clorox Total 360™ Electrostatic Sprayer dispensing
cap to the bottle. Be sure the cap is screwed all the way down,
do not overtighten.

4. Unwrap electrical cord completely and plug Clorox Total 360™

Electrostatic Sprayer into a grounded, three-pronged socket.

5. Locate the On/Off switch on the base unit. Push the Total 360

Sprayer to the “On” position. A blue light will illuminate on both
the sprayer instrument panel and unit power switch.

6. Put on appropriate personal protective equipment. See section

on personal protective equipment on page 5.

7. Remove the sprayer from the unit. A blue power indicator light

should be illuminated on the sprayer.

8. The system is now ready for use.

9. Priming the Clorox Total 360™ Electrostatic Sprayer: Depress into

an inconspicuous corner, container or drain. Spray the Clorox Total
360™ Electrostatic Sprayer for about 20 seconds to generate a
steady flow of solution.

10 When spraying, a second blue indicator light will illuminate on the

sprayer instrument panel when the trigger is depressed.

NOTE: Sprayer will automatically stay on until trigger
is depressed an additional time.

Sprayer Operation During Cleaning

1. Position Clorox Total 360™ Electrostatic Sprayer in a rear corner

of the area.

2. Direct the nozzle at the desired surface.

3. Begin to spray. Press the sprayer button once to initiate spraying.

Press once to stop flow of the sprayer.

4. Follow a continuous path around the area working from high to low

areas moving the sprayer in a sweeping motion until surfaces are
thoroughly wet.

OPERATING INSTRUCTIONS

| 9

3. Remove the

Carriage Assembly

from the

Cover

4. Remove and discard the old

Tube Leader Assembly

5. Grease the new

Tube Leader Assembly

with the supplied grease.

6. Replace the

Tube Leader Assembly

with a new one and reinstall

the

Carriage

and

Cover

in reverse order being careful not to

damage the

Tube Leader Assembly

Nozzle

The most important thing you can do to ensure trouble-free operation
of your unit is to rinse the nozzle out with clean water after every
use. By cleaning your sprayer’s nozzle after each usage, you will
avoid the long-term chemical buildup that eventually causes clogs,
poor spray patterns and shortened life of the nozzle components. In
addition to rinsing with clean water after each use, the nozzle should
periodically be disassembled and cleaned. Regular maintenance should
be performed. Nozzle maintenance schedule will vary, depending on
how often the sprayer is used and adherence to pre- and post-spray
maintenance guidelines.

It is recommended that you thoroughly read through the service
outline below before performing any regular nozzle maintenance.

To Clean/Inspect the Nozzle Assembly

1. Unscrew the cap from the nozzle base. Clean any debris from or

around any of the interior surfaces with warm soapy water.

2. Inspect for any damage to the liquid tip. If spray pattern was noted

to be inconsistent or nontypical of a healthy symmetrical spray,
remove/replace the liquid tip with an appropriate 7/16” socket
wrench.

3. Inspect nozzle electrode for any signs of electrical arching, burn

and/or corrosion. Gently push down on the spring-loaded contact
to verify a smooth spring return. If any issues are noted, remove/
replace immediately. This is done by gently pulling on the spring-
loaded contact with a pair of pliers. Otherwise service the spring-
loaded contact by applying a generous amount of dielectric grease,
available at any local automotive/hardware store.

4. Be sure to also thoroughly clean all interior surfaces of the nozzle

cover, including the main orifice. Never use a wire brush, file or
sandpaper to clean any surface or orifice.

Important:

The nozzle cover should be hand-tightened. Never use

pliers or other tools to tighten it, as this may cause damage. Removal
of the nozzle electrode is not necessary for cleaning.

Sprayer Body

The sprayer body has no serviceable parts inside.

Do not open the unit

shell as doing so will void the warranty on the sprayer

. Contact Clorox

Total 360™ Electorstatic Sprayer support center, 1-800-492-9729,
if you need to have your sprayer serviced.

Air Filter

The air filter is located on the backside of the unit and should be
replaced every 1,000 hours of use. In order to remove filter, twist it
counterclockwise until it pulls free from the base unit. Insert new filter
by twisting in clockwise until it is hand tight. Do not overtighten.

Peristaltic Pump

Tube Leader Assembly

Carriage Assembly

Cover

Tube Nuts

1. Disconnect the clear tubing inlet and outlet by twisting the

Tube Nuts

counterclockwise until both tubes have separated.

2. Rotate the

Cover

counterclockwise and pull free from the unit.

MAINTENANCE

In order for the Clorox Total 360™ Electrostatic Sprayer to remain
functional, the equipment should be cleaned on a regular basis. In
addition to general cleaning of the unit there are three user-serviceable
areas: air filter, sprayer nozzle and the peristaltic pump that should be
maintained and serviced regularly.

10 |

Volts

~115V

Running AMPS

7.0

Startup AMPS

14.6

Frequency

60 Hz

Standard Hose Length

7 ft. (2.13m)

Dimensions

29.25 in. (.74m) H x 10.00 in. (0.25m) W

x 16.00 in. (0.40m) D

Air Line Pressure

35 psi (2.4 Bar)

Weight – Empty

44 lb. (20 kg)

Weight – Full

60 lb. (27 kg)

Shipping Weight

48 lb. (22 kg)

Flow Rate

4.05 oz./min (120ml/min)

Excessive nozzle dripping

Potential Issue

Corrective Action

Damage to nozzle assembly

Inspect for damage and faulty

parts. If present, contact the

Clorox Total 360™ Electrostatic

Sprayer support center service

department.

Damage to peristaltic pump tubing

Replace pump tubing.

Dirty exterior sprayer surfaces

Clean exterior surfaces with

solvent (70–90% alcohol).

System will not turn on or has shut off suddenly

Potential Issue

Corrective Action

No power

Verify the unit is plugged in and

on a known working power outlet.

System is not switched on

Depress power switch

to illuminate.

Compressor shuts off suddenly or

won’t run while depressing the

sprayer trigger

This is a sign that the unit’s

circuit breaker has tripped or that

the compressor has overheated.

The user should look to see if

the white button (within its clear

moisture cover) has popped

out. If it has, the user should

power off the machine, look for

any physical objects that could

be loose or stuck in any of the

ventilation openings and clear/

dislodge. Press the button in and

then attempt to power the unit

back on. If the problem persists,

the user should let the unit sit

for 30 minutes to see if it’s an

overheating issue. If the unit still

refuses to restart after a cool

down then they should contact

technical service.

Compressor has overheated

Allow the unit to sit for a

minimum of 30 minutes

with the power off.

SPECIFICATIONS

TROUBLESHOOTING

NOTE:

Do NOT use a chemical in the unit that is not a Clorox-

approved product. If you encounter the issues listed below, use the
suggested troubleshooting methods. If you encounter an issue that is
not addressed in this manual, contact Clorox Total 360™ Electrostatic
Sprayer support center at 1-800-492-9729.

| 11

No Spray, Erratic Spray or Weak Spray

Potential Issue

Corrective Action

Out of liquid solution

Inspect product container

for solution level and replace

if empty.

Blockage in the nozzle or liquid tip

Remove the nozzle cover and/or

liquid tip to inspect for blockages.

Spray appears weak

The user should power the unit

off, unplug from the wall and

seek out a different electrical

outlet to try. If unavailable,

they should look to see if other

devices are running on the same

electrical circuit. Power those off

if necessary.

This could be a result of an

underrated extension cord. If an

extension cord is being used,

remove and test the unit while

using only the connected power

cord. See the extension cord

section for more information.

Damage to liquid hose or peristaltic

pump tubing

Inspect the liquid line for kinks

and/or damage.

Air pressure seems low or weak

Potential Issue

Corrective Action

Damage to the air hose

Inspect hose for knicks, damage

or areas where air is escaping.

Blockage in the nozzle

Remove the nozzle cover and

inspect for blockages.

Clogged air filter

Replace air filter.

EQUIPMENT WARRANTY

Clorox warrants the original purchaser of any Clorox Total 360™
Electrostatic Sprayer that the equipment shall be free from defects
material and workmanship for a period of one year after the date
of delivery.

Disclaimer of Implied Warranties and Consequential Damages

The Clorox obligation under this warranty, to the extent allowed by
law, is in lieu of all warranties, implied or expressed, including implied
warranties of merchantability and fitness for a particular purpose and
any liability for incidental and consequential damages with respect to
the sale or use of the items warranted.
Such incidental or consequential damages shall include, but are not
limited to: transportation, charges other than normal freight charges,
cost of installation other than cost approved by Clorox, duty, taxes,
charges for normal service or adjustments, loss of income, expenses
due to loss, damage, detention or delay in the delivery of equipment or
parts resulting from acts beyond the control of Clorox.

THIS WARRANTY SHALL NOT APPLY TO:

1. Defects, failures, damages or performance limitations caused in

whole or in part by:

a. Power failures, surges, accidents, actions of third parties,

weather or other acts of God, or

b. The product being subjected to abuse, mishandling,

misuse, negligence, improper storage, service or operation,
or unauthorized attempts to repair or alter the equipment
in any way.

2. Any Product in which any chemical other than chemical sold by

or on behalf of Clorox and expressly identified by Clorox for use
in such product.

3. Normal wear and tear.

NO EMPLOYEE OR REPRESENTATIVE OF CLOROX IS AUTHORIZED
TO CHANGE THIS WARRANTY IN ANY WAY OR GRANT ANY
OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING
AND IS SIGNED BY A CORPORATE OFFICER OF CLOROX.

© 2016 The Clorox Company
Professional Products Division
1221 Broadway
Oakland, CA 94612
1-800-492-9729
www.cloroxtotal360.com

NI-35818

Electrostatic

Sprayer CLX1000

115VAC, 60Hz, 7.0 A

Ask a Question ?