CLF Colour Par 12 Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

CLF Colour Par 12

CLF Manuals

Version 1.0 November 2012

1.BEFORE YOU BEGIN

What is included

1 x Fixture

1 x Power cable with plug

1 x User Manua

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton; check the

contents to ensure that all parts are present, and have been received in good
condition. Notify the shipper immediately and retain packing material for
inspection if any parts appear damaged from shipping or the carton itself shows
signs of mishandling. Save the carton and all packing materials. In the event that
a fixture must be returned to the factory, it is important that the fixture be returned
in the original factory box and packing.

AC POWER

This fixture has an auto-switching switch-mode power supply that can
accommodate a wide range of input voltages. The only thing necessary to do
before powering on the unit is to make sure the line voltage you are applying is
within the range of accepted voltages. This fixture will accommodate between
100V and 240V AC 50-60 Hz. Each light is connected end to end by the power
socket

“

POWER IN

”

and

“

POWER OUT

”

on the light,

Help preserve the environment! Ensure that this product is
recycled at the end of its life. Your supplier can give details

of local arrangements for the disposal of products.

Safety Instructions

WARNING!

Please read these instructions carefully, which includes

important information about the installation, usage and

maintenance of this product..

The following symbols are used to identify important safety information on the
product and in this manual:

DANGER!
Safety hazard.
Risk of severe
injury or death

DANGER!
Hazardous
Voltage. Risk of
lethal or severe
electric shock.

WARNING!
Fire hazard

WARNING!
LED light
emission. Risk
of eye injury.

WARNING!
Refer to user

This light belongs to grade I protection device, therefore the light must connect
to the earth excellently. And the power connection must be operated by the
professional technician.

Make sure that the working voltage will not higher or lower than the rated value.

Make sure that the cable didn't be damage or lacerated by sharp.

The light must be power off when it's standing idle or before clearing.

The cable must with plug, and you must pull out the cable by handle the plug.

Please be careful when installing the lighting. Never touch the bared cable, or
it will cause the deadly electric shock.

Please use the suitable and safe cable to connect the light.

Please never remodel the light randomly, we will not take the guarantee for the
faulty and damage which caused by dismantle

repair or remodel of the

nonprofessional person.

Maximum ambient temperature 40

C. Do not operate fixture at temperatures

higher than this.

Never connect the device to a dimmer pack.

Do not daisy chain power to more than 8 units @ 120V and 15 units @ 230V.

2.INTRODUCTION

Specifications

Voltage Rating: AC100V

240V 50-60Hz

Power Rating:50W

LED Quantity: 12 pcs 3 in 1 LEDs(RGB)

LED: 400mA

Beam Angle: 20

°/

/40

Ingress Protection: Ip20

Product Size: 295x 195 x255mm

Package Size: 350x260x320 mm

N/W:4.6Kg

G/W:5.6Kg

Features

RGB color mixing with or without DMX controller

5 distinct dimming curves

LED display with password protection

Operating Modes: DMX512 Connection /Master & Slave...

DMX Channels: 03CH/04CH/05CH/06CH

06 channels: Dimmer+RGB+Macro &AUTO + strobe
05 channels:RGB +Dimmer+ strobe
04 channels:RGB +Dimmer
03 channels:RGB

Product Overview

Hanging
bracket/ floor
stand

Bracket
adjustment
knob

Power in

Power out

DMX IN

DMX OUT

Control board

Dimensions

3.SETUP

Installation Requirement

This product can be used in a variety of situations, can hang and put on
the ground.

If hanging the fixture for over head use, then please follow the below steps.

Please choose the suitable location to put or hang the light when installing it.
You must use the exclusive clamp hanger and screw when hanging it, and
make sure the weight of the light is within limits of the hanger.

Please make sure without any flammable objects within 0.5m when
installing the light.

The installation should be operated by professional person; any irregular
installation will cause the body injury or equipment damage.

Block access below the work area and use suitable and stable platform
when installing or servicing fixture.

Hanging Clamp

Note: sold

separately

Safety Cable

Note: the cable must be
secured through the heat
sink ventilation
passageway.

Connection of DMX Signal Wire

Please use the fixture controller wire specially when use the DMX512
Controller. Connect the (male) 3 pin connector side of the DMX cable to
the output (female) 3 pin connector of the first fixture.

Connect the end of the cable coming from the first fixture which will have
a (male) 3 pin connector to the input connector of the next fixture
consisting of a (female) 3 pin connector. Then, proceed to connect from
the output as stated above to the input of the following fixture and so on.

This product can be connected numerous lamps in series without the
need for the signal amplifier; the signal will not be weakened.

DMX IN

DMXOUT

DMX IN

DMXOUT

DMX IN

DMXOUT

3-PIN TO 5-PIN CONVERSION CHART

Note! If you use a controller with a 5 pin DMX output connector, you will

need to use a 5 pin to 3 pin adapter.

Conductor

Ground/Shield

Data ( - ) signal

Data ( + ) signal

Do not use

3 Pin Female

(output)

Pin 1

Pin2

Pin 3

5 Pin Male (Input)

Pin 1

Pin2

Pin 3

Do not use

3 PIN TO 5 PIN CONVERSION CHART

BUTTON

DOWN

ENTER

FUNCTION

Exits from the current menu or function

Navigates downwards through the menu list and decreases the numeric
value when in a function

Navigates upwards through the menu list and increases the numeric
value when in a function

Enables the currently displayed menu or sets the currently selected
value in to the selected function

4.OPERATING INSTRUCTIONS

Control Panel Functions

MENU

OFF

DIM(1-4)

Password

V402

RED

GRED

BLUE

STRB

TIME

FADE

30S

PR00

01~09

custom

SC00

01~30

scene

Pr10

custom

SC00

01~90

scene

MAIN

FUNCTION

STAT

AUTO

DMX

RUN

PERS

SET

EDIT

DISP

SUB-

FUNCTION

D000

R000

G000

B000

S000

At00

Pr00

DMX

SLAV

03CH

04CH

05CH

06CH

DIM

REST

VER

SELECTION

000~255

(0 ~ 100%)

00~20

01~10

001 ~ 512

INSTRUCTION

User can combine RED, GREEN and
BLUE to generate a custom color

Select strobe frequency

10 auto programs available

chose program from 10

“

EDIT

”

Set DMX start address

Sets the operating mode for the fixture:to
receive signal from a DMX controller
(DMX) .receive signal or Download
programs from Master fixture. (Slave)

03 channels

RGB

04 channels

Dimmer+RGB

05 channels

Dimmer+RGB+ Strobe

06 channels

Dimmer+RGB...

"Off" means select linear dimming, or
choose dimmer 1-4 to control the dimming
speed, dimming 1 of the fastest dimming
curves, 4 for the most slowly dimming curve

Reset factory defaults

Version number

User can combine RED, GREEN, and
BLUE to generate a custom color

(0~20Hz)Select strobe frequency

(0~255) step time

transition time of last step to current step

Display is always on

Display switches off and goes into
Sleep mode if the controls have not
been pressed for 30 seconds

Menu Map

Operating instructions

1 Factory reset

SET

REST

{UP

DOWN

DOWN}

{ENTER}

Note: The password is permanently set as {UP UP

DOWN

DOWN}

Then press ENTER button

1 Custom program

EDIT

PR01

PSC01

Press

MENU

button until

EDIT

is displayed, press ENTER access program mode.

Select the program you'll edit by pressing UP/DOWN buttons. The available

range is o1-10.

Select the step you'll edit by pressing UP/DOWN buttons, and then press

ENTER button access program.

When 'R000' display on the screen, press the UP/DOWN button to choose the value.
Repeat this step to edit the value of 'G000', 'b000', 'S000', 'T000' and 'F000'.
Please pay attention for the 'S' is the rate of strobe. 'T' is the operating time of the
present step, the value is between 0 to 255. 'F' is the transitional time from previous
step to present step. The transitional time is the quickest when the FADE is 0.
Notice: Please operate the program in turn, from the 01st step to the 30th step.
When the operating program less than 30 steps, please set the final step value be 0

Repeat step 3 till complete programming.

Exit program mode by pressing

MENU

buttons three times.

DMX512 Controller Mode

Setting DMX512 Address

DMX

001--512

Access control panel function by pressing

MENU

until

DMX

is displayed.

Press ENTER, add or reduce channels by pressing UP/DOWN between 001 and 512.
Press

MENU

to exit.

Setting Channels

PERS

03CH

04CH

05CH

06CH

Access control panel function by prekssing MODE until

PERS

is displayed.

Channel

Dimming

RED

Green

Blue

Macro color

control& atuo

Value

000~255

0-4

6-19

20-24

25-49

50-59

61-74

76-84

85-89

90-94

95-99

100-104

105-109

110-114

115-119

120-124

125-129

130-134

135-139

140-144

145-149

150-154

155-159

160-164

Description

0-100%

0-100%(Or STEP TIME when CUS.01-10 is activated)

0-10 0%(Or FADE TIME when CUS.01-10 is activated)

0-100%

No Function

BLUE 100%,RED90

,GREEN97

BLUE100%

RED &GREEN DOWN

Purple (BLUE100%

RED UP)

Red (RED100%

BLUE DOWN)

Yellow (RED100%

GREEN UP )

Lime(GREEN100%

BLUE80%

RED78%)

Green (GREEN100%

RED & blue DOWN )

Teal (GREEN 10%

BLUE 10%)

Cyan (GREEN UP BLUE UP)

Colour Scroll Snap Speed 1 (Fastest)

Colour Scroll Snap Speed 2

Colour Scroll Snap Speed 3

Colour Scroll Snap Speed 4

Colour Scroll Snap Speed 5

Colour Scroll Snap Speed 6

Colour Scroll Snap Speed 7

Colour Scroll Snap Speed 8

Colour Scroll Snap Speed 9

Colour Scroll Snap Speed 10

Colour Scroll Snap Speed 11

Colour Scroll Snap Speed 12

Colour Scroll Snap Speed 13

Colour Scroll Snap Speed 14

Colour Scroll Snap Speed 15

Colour Scroll Snap Speed 16

06 channels

Channel

Macro color

control& atuo

Strobe

Value

165-169

170-174

175-179

180-184

185-189

190-194

195-199

200-204

205-209

210-214

215-219

220-224

225-229

230-234

235-239

240-244

245-249

250-255

000-255

Description

Colour Scroll Snap Speed 17 (Slowest)

Colour Scroll FADE Speed 1 (Fastest)

Colour Scroll FADE Speed 2

Colour Scroll FADE Speed 3

Colour Scroll FADE Speed 4

Colour Scroll FADE Speed 5

Colour Scroll FADE Speed 6

Colour Scroll FADE Speed 7

Colour Scroll FADE Speed 8

Colour Scroll FADE Speed 9

Colour Scroll FADE Speed 10

Colour Scroll FADE Speed 11

Colour Scroll FADE Speed 12

Colour Scroll FADE Speed 13

Colour Scroll FADE Speed 14

Colour Scroll FADE Speed 15

Colour Scroll FADE Speed 16

Colour Scroll FADE Speed 17 (Slowest)

Strobe(00~20Hz)

05 channels

Channel

Value

000~255

Description

Red

Green

Blue

Dimming

Strobe(00~20Hz)

04 channels

Channel

Value

000~255

Description

Red

Green

Blue

Dimming

03 channels

Channel

Value

000~255

Description

Red

Green

Blue

Master/Slave Control Mode

Setting master machine

Acc

ess control panel function by pressing

MENU

until

AUTO

is displayed.

Press ENTER, select

ATXX

PRXX

by pressing UP/DOWN buttons.

Press ENTER, and then press

MENU

to exit.

You can choose

ATXX

pre-set programs, the range is

o1--10

you can choose

PRXX

custom programs, the range is

o1--10

Setting slave machine

Access contro

l panel function by pressing

MENU

until

RUN

is displayed.

Press ENTER, press UP/DOWN buttons until the

SLAV

is displayed.

Press

MENU

return to MENU

Usage of Master/Slave

When two

or more fixtures connected, you can set up the first machine as the

Master and the followed fixtures as Slaves. The Master can choose pre-set programs ...

ATXX

PRXX

, all the slaves will follow the Master's operation synchronously.

Symptom(s)

1 or more LED's are
not illuminating

Breaker/Fuse keeps
blowing

Device has no power

Fixture is not
responding to DMX

Loss of signal

Possible Solution(s)

Clean the fixture regularly to avoid any such failure. This fixture is
convection cooled, which means that if the surface is kept clean
and free of debris, then proper cooling will be allowed to occur

An LED may have failed, resulting in an open circuit. In this event,
all of the red, green, or blue in a single module will no longer
illuminate. This does not mean that all of the LEDs have failed,
but the circuit is wired in series.

An LED may have failed, resulting in a short circuit. In this event, only
the single LED which has failed will no longer function. This does not
mean that all of the LEDs have failed, but the circuit is wired in series.

-Note: In the event of LED failure, a replacement LED PCB
assembly may be purchased directly from Our company

Check total load placed on the electrical circuit

Check for a short in the electrical wiring: internal and/or external

Check for power on Mains

-Note: In the event of autoswitching transformer failure, the unit
can be sent in for repair; however, a replacement part can be
ordered directly from Our company

Check Control Panel settings for correct addressing

Check DMX cables

Check polarity switch settings on the controller

Check cable connections

Call service technician

-Note: In the event of Display PCB failure, a replacement PCB
can be ordered directly from Our company

Use only DMX cables

Install terminator

Note: Keep DMX cables separated from power cables or black
lights

5. APPENDIX

Service Maintenance Guide

Symptom(s)

COLOR-CON
Controller does not
function, or does not
function properly

Stand alone
operation

Possible Solution(s)

Make sure connector is firmly connected to device

This fixture must be in the correct mode in order to properly
respond to the COLOR-CON controller. The correct mode is

“DMX”

in the onboard Control Panel

This fixture has built-in, automatic programs that may be
triggered from the onboard Control Board

Description

Glass cover

LED Lens assembly

LED Metal-core PCB assembly

Power supply seat

XLR seat

LED Driver Board

House

Bracket Assembly

Bracket adjustment metal knob

Display PCB assembly

Electronic Transformer

Part Number

6P00118

6P00105

2P00106

5100103

5100102

2P00107

6P00118

5120117

5020105

2P00103

5080125

Blow-out Diagram.

Ask a Question ?