PDF User Manual

  1. Home
  2. Manuals
  3. Breville vkj784 User Manual

Breville vkj784 User Manual

Made by: Breville
Type: User Manual
Category: Dispenser
Pages: 16
Size: 0.59 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

HotCup

HotCup

™ 

water dispenser

boils water in seconds

boils water in seconds

®

®

®

 


background image

2

Important Safety Instructions

READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

This appliance can be used by children aged from 8 years and 

above and persons with reduced physical, sensory or mental 

capabilities or lack of experience and knowledge if they have 

been given supervision or instruction concerning use of the 

appliance in a safe way and understand the hazards involved. 

Children shall not play with the appliance. Cleaning and user 

maintenance shall not be made by children unless they are 

older than 8 and supervised. Keep the appliance and its cord 

out of the reach of children aged less than 8 years.

Never use a power base other than the one supplied with the 

appliance.

Never fill the kettle above the MAX marking. If the kettle is 

overfilled, boiling water may be ejected.

If the supply cord is damaged, it must be replaced by the 

manufacturer, its service agent or similarly qualified persons 

in order to avoid a hazard.

 


background image

3

Important Safety Instructions

 

!

This appliance generates heat during use. Adequate precaution must be taken to 

prevent the risk of burns, scalds, fires or other damage to persons or property caused 

by touching the exterior whilst in use or during cooling.

 

!

Never use this appliance for anything other than its intended use. This appliance is for 

household use only. Do not use this appliance outdoors.

 

!

Always ensure that hands are dry before handling the plug or switching on the 

appliance.

 

!

Always use the appliance on a stable, secure, dry and level surface.

 

!

This appliance must not be placed on or near any potentially hot surfaces (such as a 

gas or electric hob).

 

!

Do not use the appliance if it has been dropped, if there are any visible signs of 

damage or if it is leaking.

 

!

Ensure the appliance is switched off and unplugged from the supply socket after use 

and before cleaning.

 

!

Always allow the appliance to cool before cleaning or storing.

 

!

Never immerse any part of the appliance or power cord and plug in water or any other 

liquid.

 

!

Never let the power cord hang over the edge of a worktop, touch hot surfaces or 

become knotted, trapped or pinched.

 

!

Never leave the appliance unattended when in use.

 

!

Beware of steam coming from the spout or lid especially during refilling. Never open 

the lid during the boiling cycle.

 

!

Never fill the appliance when it is positioned on the power base.

 

!

Never use the appliance without sufficient water in it for it to operate correctly.

 

!

Never allow the appliance to boil dry.

 

!

Always operate the appliance with a cup or suitable container placed below the 

dispensing nozzle.

 


background image

4

1.  Removeable drip tray

 

No mess, just lift it off the power base and rinse under the tap. Holds over 1 cup of 

water before it needs emptying.

2.  Removable stainless steel drip tray cover
3.   Dispensing nozzle
4.  Stop button

 

Press to immediately stop the boil sequence or to stop water that is being dispensed.

5.  Start button

 

Press to start the boil sequence.

6.  Dispensing control

 

This control allows you to select the amount of water dispensed by your HotCup™ 

water dispenser. Move it towards   for less water or   for more water.

7. Lid
8.  Lid release button

 

Press to open the lid and fill the water tank.

9.  Illuminated water reservoir

 

Easy fill water reservoir holds up to 2 litres.

10.  Heating chamber
11.  Power base

 

Identifying the Parts

 


background image

5

t

q

w

e

r

y

u

i

o

a

s

 


background image

6

Using Your HotCup™ Water Dispenser

Before using your HotCup™ water dispenser for the first time

• 

Remove your HotCup™ water dispenser carefully from the box. Remove any 

packaging and promotional material and position your HotCup™ water dispenser on 

a dry, level, secure work surface away from the edge.

• 

Follow the instructions below on using your HotCup™ water dispenser and discard 

the first five measures of boiling water (i.e. the first full tank of water). This will 

remove any residues that may remain from the manufacturing process.

Using your HotCup™ water dispenser

 Always position your HotCup™ water dispenser in such a way that the start 

button cannot be accidentally operated, especially by children. As you use your 

HotCup™ water dispenser, a certain portion of the water boiled will be transferred 

back to the water reservoir. This will mean the water reservoir may become hot. 

Always use care when handling your HotCup™ water dispenser.

1. 

Press the lid release button.

2. 

Fill the water reservoir from your cold tap. The water level should be between the 

MIN and MAX markings.  

3. 

Close the lid and press the stop button. This will make sure that your HotCup™ water 

dispenser will not immediately start a boil cycle when you place it onto the power 

base.

4. 

Connect your HotCup™ water dispenser

 

to a mains supply socket. 

5. 

Place a suitable cup or container with a tea bag, coffee, sugar, etc. below the 

dispensing nozzle. Never operate your HotCup™ water dispenser without a cup or 

suitable container placed below the dispensing nozzle. Adjust the dispensing control 

to the required setting. The control adjusts the quantity of boiling water dispensed 

by your HotCup™ water dispenser. For smaller cups like teacups, set the control 

towards the   setting; for larger cups like coffee mugs, set the control towards the   

setting. If you are not sure which setting to use, it’s best to use a lower setting until 

you gain experience using your HotCup™ water dispenser. 

6. 

Press the start button. The water tank will light up and your HotCup™ water 

dispenser will start to boil.

7. 

The selected quantity of boiling water will be dispensed into the cup. Your HotCup™ 

water dispenser

 

is now ready to use again. If, after just having boiled, the start button 

doesn’t stay in the down position, simply wait a few seconds before trying it again.

Stopping your HotCup™ water dispenser

If you have started the boil procedure and then decide you want to stop your HotCup™ 

water dispenser for any reason, simply press the stop button. You can also stop water 

that is being dispensed by pressing the stop button. The boiled water will be safely 

transferred back into the water reservoir.

 


background image

7

MAX

MIN

MIN

MAX

q

w

e

r

t

y

u

SMALL

CUP

LARGE

CUP

 


background image

8

Cleaning

 

Always switch off and unplug your HotCup™ water dispenser and allow it to 

completely cool before cleaning. Never immerse the base unit, power cord or 

plug in water or any other liquid. Do not use harsh abrasives, chemicals or oven 

cleaners.

Emptying your HotCup™ water dispenser

1. 

After your HotCup™ water dispenser has completely cooled down, unplug it from the 

mains supply socket. 

2. 

Press the lid release button.

3. 

Hold your HotCup™ water dispenser over a sink and pour the water out.

4. 

Still holding your HotCup™ water dispenser over the sink, turn it the right way up 

and allow any water to drain out of the dispensing nozzle. If no water drains out of 

the nozzle, it may be because the stop button has been accidentally or intentionally 

pressed. Press the start button to allow water to drain from the nozzle.

5. 

Repeat steps 3 and 4 until all the water has been emptied from your HotCup™ water 

dispenser.

If your HotCup™ water dispenser will not be used for an extended period (e.g. if you are 

on holiday), we recommend that you first empty it. Before using your HotCup™ water 

dispenser again, carry out several boil cycles discarding the water each time.

Cleaning

Clean the exterior surface of your HotCup™ water dispenser with a damp cloth and then 

polish it with a soft, dry cloth. Do not use steel wool pads or harsh/abrasive cleaners.

 


background image

9

q

w

e

r

 


background image

10

safety and efficiency

To ensure the safe and efficient operation of your HotCup™ water dispenser it is 

important to descale it regularly. The harder your water the more regularly it will need 

doing. Your water company should be able to tell you how hard the water is in your 

area. Untreated scale deposits prevent the element conducting heat efficiently therefore 

wasting electricity. Scale can also cause your HotCup™ water dispenser to malfunction or 

even cause premature failure.

Descaling using a proprietary descaling product

1. 

Fill your HotCup™ water dispenser to the MAX fill level and place an empty cup on 

the drip tray. Press the start button and wait for the water to be dispensed into the 

cup.

2. 

Add a citric acid-based proprietary descaling product to the hot water in the cup and 

stir.

3. 

Tip the contents of the cup into your HotCup™ water dispenser and close the lid.

4. 

Place the empty cup on the drip tray and press the start button.

5. 

Wait for the water to be dispensed into the cup.

6. 

Discard the water from the cup. 

7. 

Repeat steps 4, 5 and 6 until the water level is at the MIN mark. Open the lid and 

empty any remaining water into the sink. Rinse your HotCup™ water dispenser by 

filling it with clean water and emptying it into the sink (see 

Emptying your HotCup™ 

water dispenser

 on page 8).

 

Fill your HotCup™ water dispenser with fresh water to the MAX fill level and place an 

empty cup on the drip tray. 

8.  Pres the start button and wait for the water to be dispensed into the cup. 

9.  Discard the water in the cup. Repeat steps 8 and 9 until the water level is at the MIN 

mark. Open the lid and empty any remaining water into the sink.

Descaling using vinegar or citric acid

1.  You can use ordinary vinegar (white or malt) or citric acid to descale your HotCup™ 

water dispenser. Inexpensive, ordinary vinegar can be purchased in large bottles 

from any supermarket. Citric acid can be bought from pharmacies, home brewing/

winemaking suppliers or on-line retailers.

2.  If you are using vinegar, make up a solution of 1 cup of vinegar to 1 cup of water. If 

you are using citric acid, mix 30g of the citric acid with 500ml of water.

3.  Pour the solution into the tank, close the lid and allow it to stand for 1 hour. 

4.  Cycle your HotCup™ water dispenser (as described in steps 4-6 above) until the 

level is at the MIN mark. Open the lid and empty any remaining solution into the sink. 

Rinse your HotCup™ water dispenser several times by filling it with clean water and 

emptying it into the sink. 

5.  Fill your HotCup™ water dispenser with fresh water to the MAX fill level and place an 

empty cup on the drip tray. 

6.  Press the start button and wait for the water to be dispensed into the cup. 

7.  Discard the water in the cup. Repeat steps 6 and 7 until the water level is at the MIN 

mark. Open the lid and empty any remaining water into the sink.

8.  Finally, rinse your HotCup™ water dispenser several times with clean water.

 


background image

11

q

w

e

r

t

y

u

i

o

 


background image

12

Problem

Possible Cause

Solution

The start switch will not stay 

in the on position.

The appliance has not reset 

itself after the boiling cycle.

The appliance is still too hot 

after the last boil cycle. Wait 

a few seconds for it to cool 

slightly before trying again.

The water tank does not 

illuminate and the appliance 

does not dispense boiling 

water.

• 

The appliance is not 

plugged in.

• 

The appliance is not 

positioned correctly on its 

power base.

• 

The fuse has blown.

• 

The appliance has boiled 

dry.

• 

Check the appliance is 

plugged in and switched 

on at the supply socket.

• 

Check that the dispensing 

nozzle is positioned 

centrally over the drip tray.

• 

Check the fuse in the 

plug.

• 

Allow the appliance to 

cool down completely 

then refill it with water.

The appliance does not 

dispense a full cup of water

• 

The appliance has 

excessive scale.

• 

The dispensing control 

may be set too low.

• 

Descale the appliance

• 

Adjust the dispensing 

control

The appliance produces 

excess steam but does not 

dispense boiling water.

• 

The water level has 

dropped below the MIN 

level.

• 

The appliance has 

excessive scale.

• 

Fill with water between 

the MIN and MAX 

markings then restart the 

boil cycle.

• 

Descale the appliance.

The appliance makes a 

noise and there is a ‘clunk’ 

sound after water has been 

dispensed.

This is the sound of the 

internal valve operating after 

the boil cycle finishes.

This is normal operation.

Water drips from the 

dispensing nozzle after the 

boil cycle has finished.

There is a residual amount 

of water left inside the 

appliance after the boil cycle.

This is normal operation

Steam comes out from 

behind the start button and 

behind the dispensing nozzle

Steam is being vented in a 

controlled manner through 

designed vents

This is normal operation

The water reservoir is getting 

hot.

Hot water is being returned 

to the water reservoir

This is normal operation. 

The appliance immediately 

turns iteslf on when it is 

placed on the power base.

The appliance is already 

switched on.

Press the stop button.

Troubleshooting

 


background image

13

Connection to the mains supply

 This appliance must be earthed.

If the plug is not suitable for the socket outlets in your home, it can be removed and 

replaced by a plug of the correct type.
If the fuse in a moulded plug needs to be changed, the fuse cover must be refitted. The 

appliance must not be used without the fuse cover fitted.
If the plug is unsuitable, it should be dismantled and removed from the supply cord and 

an appropriate plug fitted as detailed. If you remove the plug it must not be connected to 

a 13 amp socket and the plug must be disposed of immediately.
If the terminals in the plug are not marked or if you are unsure about the installation of the 

plug please contact a qualified electrician.

Plug should be BS1363 approved 

Fit a 13 Amp Fuse

Ensure that the outer sheath of the cable 

is firmly held by the clamp

 


background image

14

After sales service

These appliances are built to the very highest of standards. There are no user serviceable 

parts. Follow these steps if the unit fails to operate:

1. 

Check the instructions have been followed correctly.

2. 

Check that the fuse has not blown.

3. 

Check that the mains supply is functional.

If the appliance will still not operate, return the appliance to the place it was purchased for 

a replacement. To return the appliance to the Customer Service Department, follow the 

steps below:

1. 

Pack it carefully (preferably in the original carton). Ensure the unit is clean.

2. 

Enclose your name and address and quote the model number on all correspondence.

3. 

Give the reason why you are returning it.

4. 

If within the guarantee period, state when and where it was purchased and include 

proof of purchase (e.g. till receipt).

5. 

Send it to our Customer Service Department at the address below:

Customer Service Department

Jarden Consumer Solutions (Europe) Limited

Middleton Road, Royton, Oldham OL2 5LN, UK.

Telephone: 0800 525 089  Fax: 0161 626 0391

e-mail: enquiriesEurope@jardencs.com

Turn on your Creativity

Let the Breville

®

 team help you turn on your creativity with a gateway to a world of food 

and drinks without limits. You don’t have to travel far—just to your computer, tablet or 

mobile—where you will discover our FREE website with top tips and recipes to inspire 

your imagination. Join us now at

 www.turnonyourcreativity.com

  

®

 


background image

15

Guarantee

Please keep your receipt as this will be required for any claims under this guarantee.
This appliance is guaranteed for 1 year after your purchase as described in this 

document.

During this guaranteed period, if in the unlikely event the appliance no longer functions 

due to a design or manufacturing fault, please take it back to the place of purchase, with 

your till receipt and a copy of this guarantee.
The rights and benefits under this guarantee are additional to your statutory rights, which 

are not affected by this guarantee. Only Jarden Consumer Solutions (Europe) Limited. 

(“JCS (Europe)”) has the right to change these terms.
JCS (Europe) undertakes within the guarantee period to repair or replace the appliance, 

or any part of appliance found to be not working properly free of charge provided that:

• 

you promptly notify the place of purchase or JCS (Europe) of the problem; and

• 

the appliance has not been altered in any way or subjected to damage, misuse, 

abuse, repair or alteration by a person other than a person authorised by JCS 

(Europe).

Faults that occur through, improper use, damage, abuse, use with incorrect voltage, acts 

of nature, events beyond the control of JCS (Europe), repair or alteration by a person 

other than a person authorised by JCS (Europe) or failure to follow instructions for use 

are not covered by this guarantee. Additionally, normal wear and tear, including, but not 

limited to, minor discoloration and scratches are not covered by this guarantee.
The rights under this guarantee shall only apply to the original purchaser and shall not 

extend to commercial or communal use.
If your appliance includes a country-specific guarantee or warranty insert please refer 

to the terms and conditions of such guarantee or warranty in place of this guarantee or 

contact your local authorized dealer for more information.

Waste electrical products should not be disposed of with Household waste. Please 

recycle where facilities exist. E-mail us at enquiriesEurope@jardencs.com for further 

recycling and WEEE information.

Jarden Consumer Solutions (Europe) Limited
5400 Lakeside
Cheadle Royal Business Park
Cheadle

SK8 3GQ
UK

 


background image

Jarden Consumer Solutions (Europe) Limited

Cheadle Royal Business Park, Cheadle, SK8 3GQ, United Kingdom

e-mail: enquiriesEurope@jardencs.com

Telephone: 0161 621 6900

For Customer Service details, please see the website.

www.breville.co.uk

© 2015 Jarden Consumer Solutions (Europe) Limited

All rights reserved. Imported and distributed by Jarden Consumer Solutions (Europe) Limited,  

Cheadle Royal Business Park, Cheadle, SK8 3GQ, United Kingdom.

The product supplied may differ slightly from the one illustrated due to continuing product development. 

Printed in China

®

VKJ318_VKJ784_Rev6    06/15 

93027-5  UKPUL

 

P.N. 183613