Full Text Searchable PDF User Manual
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
1
MBC-2690
MBC-2693
User’s Manual
Version 1.0
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
2
Copyright Notice
This document is copyrighted, 2002. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, nor for any in-
fringements upon the rights of third parties which may result from its use.
The material is this document is for product information only and is subject
to change without notice.
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
3
Acknowledgments
All other product names or trademarks are properties of their
respective owners.
C&T is a trademark of C&T Software International, Inc.
Microsoft Windows® is a registered trademark of Microsoft Corp.
C&T is a trademark of Chips and Technologies, Inc.
AAEON is a registered trademark of AAEON Technology Inc.
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
4
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
•
1 MBC-2690 OR MBC-2693 VGA Board
•
1 CD-ROM for manual and Driver
•
1 Quick Installation Guide
•
1 Screws bag
If any of these items are missing or damaged, contact your distributor
or sales representative immediately.
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
5
Index
Copyright Notice --------------------------------------------- 2
Acknowledgments-------------------------------------------- 3
Packing List -------------------------------------------------- 4
1.1 Introduction ---------------------------------------------- 6
1.2 Features--------------------------------------------------- 7
1.3 Locating Components ------------------------------------ 8
1.4 Jumpers and Connectors --------------------------------- 9
1.5 Installation----------------------------------------------- 17
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
6
1.1 Introduction
This section describes the essential components of which the card consists.
Basically the card integrates a high-performing flat-panel/CRT controller, a
32K bytes BIOS EEPROM, 2MB/4MB high performance video memory
embedded on chipset, and a clock synthesizer. Thus integrated the card can
almost support, by employing the standard or a customized BIOS EPROM,
any of the currently most popular LCDs and traditional CRT monitors in
high resolution modes.
The Chipset of flat-panel/CRT controller is C&T 69000/69030. It is
VGA-compatible and highly integrated, supporting a wide variety of LCD, EL,
Gas plasma panels as well as the traditional CRT monitors. It also supports
simultaneous flat-panel/CRT operation. It can support the standard, super
VGA, XGA, SXGA and UXGA (MBC-2693 Only) resolution modes.
In addition to a 36-bit universal panel interface built on the cards, via which
you can quickly set up most of the popular LCDs. Via the 36-bit universal
interface you can also have two connectors 18-bit and 36-bit ( two channels )
ones built on the LVDS board (option) piggybacked onto the card.
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
7
1.2 Features
•
C&T 69000/69030 flat-panel/CRT controller
•
PCI bus
•
External CRT interface (D_SUB 15-pin)
•
36-bit universal and LVDS panel interface
•
18 or 36-bit TFT panel interface
•
Internal CRT interface (10-pin)
•
Supports the CRT display resolutions:
A.
MBC-2690: up to 1024x768 65K colors, 800x600 &
640x480 true color, non-interlace
B.
MBC-2693: up to 1600x1200 65K colors, 1280x1024 &
1024x768 & 800x600 & 640x480 true color,
non-interlace.
•
2MB/4MB SD-RAM on chip
•
LVDS external LCD interface (option)
•
Emulate EGA, CGA and Hercules display adapters
•
Supports simultaneous flat-panel/CRT operation
•
Advanced power management features minimizing power
consumption during :
A. Normal operation
B. Stand by (sleep) mode
C. Panel-off power saving mode
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
8
1.3 Locating Components
This section shows you the basic layout of the card and the location of each
of the essential components on it. You can easily obtain that by looking into
the following three diagrams. This will further strengthen your
understanding about the basic integration of the card.
32K
BIOS
P
C
I
I
N
T
E
R
F
A
C
E
C&T 69000/69030
VGA CHIP
LVDS-T100/200
18 /36 bit LVDS
Frame Buffers
CRT Connect
(Default)
MB C-2690/2693 Flat Panel/CRT control card system block
2MB/4MB
CRT Header
Header
LVDS Interface
36-bit TFT
interface
**Only supports one CRT signal. CRT header is optional function.
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
9
Location of Connectors and Jumpers
VGA
J4
J6
J3
J5
J2
JP2
J1
JP3
BIOS
CHIPS
1
2
7
8
1
1
1
1
2
2
2
1
50
49
49
50
27
28
9
10
1
2
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
10
Mechanical Drawing
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
11
1.4 Jumpers and Connectors
Jumper Settings
Jumpers allow users to manually customize system configurations to
their suitable application needs.
J1: Panel Type Select
J1: C&T 69000 / 69030 Support Panel
Type
Support Panel
Short
1
1024 x 768 TFT Color
1-2,3-4,5-6,7-8
2
1280 x 1024 TFT Color
1-2,3-4,5-6
3
648 x 480 DSTN Color
1-2,3-4,7-8
4
800 x 600 DSTN Color
1-2,3-4
5
800 x 600 TFT Color
1-2,5-6,7-8
6
640 x 480 18 bit TFT Color
1-2,5-6
7
1024 x 768 TFT Color
1-2,7-8
8
800 x 600 TFT Color
1-2
Note:
LCD Supporting Reference List
LCD Size
Model Name
Corresponding type
15”
Fujitsu
FLC38XGC6V
Type 7
12”
Toshiba LTM12C289
Type 8
10.4”
Jilin Chijing CJM10C011A
Type 6
10.4”
SAMSUNG LTN104S2-L01
Type 5
**
You have to prepare the interface (connecting cable) of the LCD and the
VGA card
.
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
12
JP2: Panel Voltage Select
Panel Voltage
JP2
+3.3V
1-2
Default
+5V
2-3
JP3: Backlight Control Select
Panel Voltage
JP3
VDD
1-2
Default
VEE
2-3
Note:
VDD: Power sequencing control for panel driver electronics
voltage VDD
VEE: Power sequencing control for panel bias voltage VEE
may also be configured as (Inverter
Backlight control)
ENABKL
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
13
Connector Pin Assignment
VGA: CRT DB15 Connector
PIN
NAME
PIN
NAME
PIN
NAME
1
R
6
GND
11
N/A
2
G
7
GND
12
DDCDATA
3
B
8
GND
13
HSYNC
4
N/A
9
N/A
14
VSYNC
5
GND
10
GND
15
DDCCLK
J2: Internal VGA Signal Connector
PIN
NAME
PIN
NAME
1
RED
2
DDCDATA
3
GREEN
4
DDCLK
5
BLUE
6
GND
7
HSYNC
8
GND
9
VSYNC
10
GND
J3: Internal LVDS Daughter Board/ PIN Header (1)
PIN
NAME
PIN
NAME
1
E1
2
E2
3
E3
4
E4
5
E5
6
E6
7
E7
8
E8
9
E9
10
E10
11
E11
12
E12
13
E13
14
E14
15
E15
16
E16
17
E17
18
E18
19
E19
20
E20
21
E21
22
E22
23
E23
24
E24
25
E25
26
12V SAFE
27
5V SAFE
28
GND
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
14
J4: External LVDS Outlet DB-25 Connector
PIN
NAME
PIN
NAME
1
E1
14
E2
2
E3
15
E4
3
E5
16
E6
4
E7
17
E8
5
E9
18
E10
6
E11
19
E12
7
E13
20
E14
8
E15
21
E16
9
E17
22
E18
10
E19
23
E20
11
E21
24
E22
12
E23
25
E24
13
E25
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
15
J5: Flat Panel Digital Signal
PIN
NAME
PIN
NAME
1
+12V
2
+12V
3
GND
4
GND
5
+3.3V/ +5V
6
+3.3V/ +5V
7
ENVEE
8
GND
9
FPD0
10
FPD1
11
FPD2
12
FPD3
13
FPD4
14
FPD5
15
FPD6
16
FPD7
17
FPD8
18
FPD9
19
FPD10
20
FPD11
21
FPD12
22
FPD13
23
FPD14
24
FPD15
25
FPD16
26
FPD17
27
FPD18
28
FPD19
29
FPD20
30
FPD21
31
FPD22
32
FPD23
33
FPD24
34
FPD25
35
CLK
36
VSYNC
37
DE
38
HSYNC
39
GND
40
ENABKL
41
FPD26
42
FPD27
43
FPD28
44
FPD29
45
FPD30
46
FPD31
47
FPD32
48
FPD33
49
FPD34
50
FPD35
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
16
J6: Internal LVDS Daughter Board/ PIN Header (2)
PIN
NAME
PIN
NAME
1
LVDS CLK
2
FPD
3
FPD34
4
FPD
5
FPD35
6
FPD
7
FPD30
8
FPD
9
FPD29
10
FPD
11
FPD25
12
FPD
13
FPD24
14
FPD
15
FPD23
16
FPD
17
FPD16
18
FPD
19
FPD17
20
FPD
21
FPD19
22
FPD
23
FPD13
24
FPD
25
FPD15
26
FPD
27
FPD7
28
FPD
29
+3.3V/ +5V
30
+3.3V/ +5V
31
FPD9
32
FPD
33
FPD4
34
FPD
35
FPD3
36
FPD
37
FPD2
38
FPD
39
DE
40
FPD
41
CLK
42
ENABKL
43
ENVDD
44
VSYNC
45
ENVEE
46
HSYNC
47
GND
48
GND
49
+12V
50
+12V
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
17
1.5 Software Installation
This PCI VGA card supports Microsoft ® Windows® Version
9x/2000/NT/XP operating system (OS).
Window 98
1. Install OS as you normally would for a VGA display. Run OS
to make sure that it is working correctly.
2. Place the supporting CD-ROM into your CD-ROM drive. In
Windows Program Manager, choose File from the Options
Menu. Then from the pull-down menu, choose Run.
3. Execute the installation wizard “setup.exe” in the following
path:
“cd-rom”
:\ Driver\ VGA card\
“model name”
\ Win98
"cd-rom"
: the drive letter of your CD-ROM drive
“model name”
: the model number of your product
Press the <Enter> key or click OK to begin the installation.
4. Simply follow the instruction to complete the installation. Shut
down and restart your system.
P C I V G A C a r d
M B C - 2 6 9 0 / 2 6 9 3
MBC-2690/2693 User Manual
18
Windows NT4.0
1. Install Windows NT4.0 as you normally would for a VGA display. Click
the
Start
button, go to
Settings
and click on
Control Panel
icon. Then
choose the
Display
and double click on the icon. In the
Display
Properties
window, click the
Setting
button, then click the
Display
Type
button into the
Display Type
windows, then click on
Change
button from the
Adapter Type
icon. And click on
Have Disk
button
in the change display windows.
2. Place the Supporting CD-ROM into your CD-ROM drive. In the
Select Device
window, click on
Have Disk
, select “
Browse
” and find
the NT4.0 driver from:
“cd-rom”
\ Driver\ VGA card\
“model name”
\ WinNT4
"cd-rom"
: the drive letter of your CD-ROM drive
“model name”
: the model number of your product
and then click OK. The name of the
Chips and Technologies, Inc.
Video Controller
driver will appear highlighted in the Modules list box.
Select Chips and Tech. 69000 and Click
OK
. Click
OK
to start the
driver installation.
3. Once the installation is complete, the
Chang Display Type
window
will reappear. Click on close to close the window. Then the
Display
Properties
window will reappear. Click on
Apply
. Restart the system
for the new settings to take effect.