Full Text Searchable PDF User Manual
Thank you for purchasing our product.
Please read this User’s Manual before
using the product
.
Change without Notice
7” (Q)TFT LCD MONITOR
USER MANUAL
e
-4
1
SAFETY PRECAUTIONS
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-
Consult the dealer or an experienced radio / TV technician for help.
z
You are cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void your authority to operate the
equipment.
This device complies with Part 15 FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received including interference
that may cause undesired operation
2
CONTENT TABLE
Safety Precaution.……..……………………………………………………………… 2
Content Table….….…………………………………………………………………… 3
Feature….……………………………………………………………………………… 4
1. Package
Contents…….…………………………………………………………. 5
2. TFT
Installation…………………………………………………………………… 6
3. Signal
Cable
Description……..………………………………………………….
7
4. Control Cable Description……..………………………………………………… 9
5. Front
Panel
Control.……………………………………………………………… 10
OSD Menu ………………………..…..………………………………………….. 11
Display……………………………………………………………………………. 12
OSD Display……………………………………………………………………… 13
Camera……………………………………………………………………………. 14
Recall………………………………………………………………………………. 15
Exit…………………………………………………………………………………. 15
6. Vehicle Installation ………………………….…………………………………… 16
7. Specification…..…………………………………………………………………. 17
3
8. Attachment…..…………………………………………………………………….
18
Feature
y
Support up to 4 CCD Camera inputs (Mini din connector)
y
Extra RCA input for multimedia (VCD, DVD, Game device)
y
Provide 2 Video / 1 Audio Signal Output
y
Support Single / Dual / Quad Picture
y
Signal Trigger for Side / Rear View
y
OSD Control for Individual Normal / Mirror Camera Image
y
Auto Day & Night Control via CDS
y
Auto Detection for NTSC / PAL System
4
1. Package Contents
Item Qty.
1. 7” LCD Monitor
1
2. Sun-hood
1
3. Mounting Bracket
1
4. Accessories
1
5. Control Cable
1
6. User Manual
1
5
2. TFT Installation
Step 1
Check the package and make sure all parts are
included
Step 2
Clip the sun-hood on to the monitor
Step 3
Make sure it is installed properly
Step 4
Install the monitor on to the bracket
Step 5
Adjust the monitor to an appropriate / comfortable
viewing angle before tightening the screws
Step 6
Connect the control cable included to the power socket
which located at rear side of monitor
Step 7
Monitor installation is now completed.
Each control cable wire is attached with a sticker to
indicate its signal function. Referred to the
identification sticker for further installation.
6
3
.
Signal Cable Description
1. CAM R (Mini din) (NTSC/PAL system presume by this car rear CCD)
For 1
st
camera connection
CAM
B
C AM
R
CA
MC
CA
MA
AV
V
ID
EO
IN
LIFE
V
IDE
O O
UT
LIF
E
VID
EO
IN
AV
A
UD
IO
IN
CA
M
OU
T
CAM-B
CAM-R
C AM-C
CAM-A
AV VIDEO IN
LIVE V IDEO OUT
LIVE AUDI O O UT
AV AUDIO I N
CAM OUT
Red color line
Yellow colo r line
Wh it e co lor li n e
Blac k colo r li ne
Gr een c olor lin e
2. CAM
A
(Mini
din)
For second camera connection
3. CAM B (Mini din)
2. CAM A (Mini din)
For third camera connection
4. CAM C (Mini din)
For fourth camera connection
5. LIVE VIDEO OUT (RCA – White Wire)
On screen video loop out (for recording, second monitor or other device)
6. LIVE AUDIO OUT (RCA – Black Wire)
On screen audio loop out (for recording, second monitor or other device)
7. AV VIDEO IN (RCA – Yellow Wire)
Connection for any Video signal (DVD, VCD, Game)
8. AV AUDIO IN (RCA – Red Wire)
Connection for any Audio signal (such as DVD, VCD, Game)
9. CAM OUT (RCA – Green Wire)
Video loop out (for recording, second monitor or other device)
7
z
Mini Din Pin Assignment
* Type 1 (Standard):
1. ----- 4. GND
2. ----- 5. +12V
3. Audio 6. Video
*Type 2
(Optional)
:
1. GND
4. +12V
2. ------
5. -------
3. Video 6. Audio
4
6
5
3
2
1
z
Function of the Audio
Cam A + Cam B
No Audio Function
Cam A
No Audio Function
Cam B
No Audio Function
Cam C + Cam R
No Audio Function
QUAD No
Audio
Function
Cam A + Cam R
Audio form Cam R
Cam B + Cam R
Audio form Cam R
Cam R
Audio form Cam R
Cam C
Audio form Cam C
AV Audio
form
AV
PS: Audio function is only available with CAM C and CAM R,
CAM A and CAM B do not support Audio function
8
PA
RK
RIG
HT
P
O
W
ER
G
N
D
LE
FT
RE
VE
RS
E
RIGHT
O ran ge color line
B lack color line
G ND
PARK
White colo r line
Red color line
POWER
Yellow color line
LEFT
Blu e co lor lin e
Reverse
4. Control cable Description
WIRE COLOR
FUNCTION
REMARK
ON SCREEN VIEW
RED ACC
POWER
BLACK GND
WHITE
Parking Control
Active GND
BLUE
Reverse Control
Active Power Level
Connect to Reverse
Light
ORANGE
Right Turn Control
Active Power Level
Connect to Direction
Light (R)
YELLOW
Left Turn Control
Active Power Level
Connect to Direction
Light (L)
Jump S our ce P o wer
M e nu
AV
Jump S ource P ower
M enu
C AM R
CAM R
CAM B
CAM A
CAM R
1. The control cable sequence : Reverse > Right / Left > Park (AV)
2. With car power is on, the monitor power is off, when making a reverse / right / left turn, the monitor
9
will display default screen.
5. Front Panel Control
POWER
Press the power button to activate the monitor or to keep the monitor
under stand by mode.
SOURCE
With power on press this button to select image sequence CAM A+B
Æ
CAM C+R
Æ
CAM A
Æ
CAM B
Æ
CAM C
Æ
CAM R
Æ
CAM A+B…,
With pull hand break, press this button to select image sequence
AV
Æ
CAM A+B
Æ
CAM C+R
Æ
CAM A
Æ
CAM B
Æ
CAM C
Æ
CAM R
Æ
AV…
.
JUMP
Press this button to display defined camera input, user can select
QUAD / CAM A+B / CAM C+R / CAM A / CAM B / CAM C / CAM R
via OSD as default value.
MENU
This encoder switch provides the following function:
1. Activate OSD menu: Press the switch to activate the OSD menu.
After the OSD menu is activated, in case the user does not proceed
for further set up, the OSD menu will then automatically turn off within
several seconds.
2. Enter Function: Press the encoder switch to act as “Enter” : functions
under the OSD menu.
3. Volume Value: Exit the OSD menu, user can turn this switch left or
right to adjust the volume value.
*When pull the hand break, user need to press SOURCE button again to display
AV picture.
10
OSD MENU
1. Press the MENU button to enter to the OSD Menu
2. Turn the MENU button left or right to select the setting you
wish to proceed. The color of the content will turn YELLOW
to identify your selection.
3. Press the MENU button again until the color of the content turns
from Yellow to Red to enter system setting.
Turn the MENU button left or right to adjust your setting value.
Enter to Main menu:
D ISPLAY
O SD D ISPLAY
C AMERA
R ECALL
EXIT
11
DISPLAY
The display set up contains different setting for the TFT:
BRIGHTNESS
Provide adjustment for the overall picture shade and brightness of TFT
display. Setting value from 0 ~ 31. Default value at “16”.
CONTRAST
Provide adjustment for the contrast level of the TFT display between the
light and dark areas. Setting value from 0 ~ 31. Default value at “16”.
COLOR
Provide adjustment for the color of TFT display between the light and
dark area . Setting value from 0 ~ 31. Default value at “16”.
HUE (It can work under NTSC system)
Provide adjustment for the picture TINT between light and dark area.
Setting value from 0 ~ 31. Default value at “16”.
AUTO DAY&NIGHT
Select “ON” to activate the auto day & night function or
“OFF” to deactivate it. Default value as “ON”
DIR IMAGE
Select the on screen image during left / right turn.
DUAL:
With proper wiring, the screen will display dual image
for both rear and right hand side view when making a
right turn. Then while left turning, the screen will show
dual image for both rear and left hand side view.
SINGLE: Screen shows only single picture on direction turn.
The screen will show only left side view on left turn and
only right side view on right turn.
Default: DUAL
RETURN
12
Return to the previous screen.
OSD DISPLAY
The OSD DISPLAY set up contains the on screen identification and
the activation of the distance gauge.
Jump S ourc e P o wer
Menu
DISPLAY
DISTA NCE GAU GE
RETUR N
ON
ON
DISPLAY
Set “ON” to show the source of video input on screen or “OFF” to
keep it invisible. Default as “ON”
DISTANCE GAGE
Set the distance gage “ON” to show the distance gage on screen while
reserving or “OFF” to de-activate the distance gage. Default as “ON”
RETURN
Return to the previous screen.
13
CAMERA
MIR R OR
JU MP
C AM OUT
R ETU RN
ON
OFF
OFF
OFF
C AM A
C AM B
C AM C
C AM R
C AM QUA D
QU AD
MIRROR
Select “ON” to activate the mirror function for different cameras or “OFF”
for a normal image.
Default:
CAM A
“OFF”
CAM B
“OFF”
CAM C
“OFF”
CAM R
“ON”
JUMP
By pressing this button, the driver will be able to obtained the image
selected under this setting. Default as: QUAD
QUAD
Obtain image from all camera input in quad picture
while pressing the JUMP button and press again to
return to default screen.
CAM A+B
Obtain image from camera A+B in dual picture while
pressing the JUMP button and press again to return to
default screen.
CAM C+R
Obtain image from camera C+R in dual picture while
pressing the JUMP button and press again to return to
default screen.
CAM A
Obtain image from camera A while pressing the JUMP
button and press again to return to default screen.
CAM B
Obtain image from camera B while pressing the JUMP
button and press again to return to default screen.
14
CAM C
Obtain image from camera C while pressing the JUMP
button and press again to return to default screen.
CAM R
Obtain image from camera R while pressing the JUMP
button and press again to return to default screen.
CAM OUT
Composite video loop out to recorder, monitor or other device
Default as: QUAD
QUAD
Recording or viewing from the output device in quad
mode
CAM A
Recording or viewing from the output device for CAM
A image
CAM B
Recording or viewing from the output device for CAM
B image
CAM C
Recording or viewing from the output device for CAM
C image
CAM R
Recording or viewing from the output device for CAM
R image
RECALL :
Use this feature to recall the factory default settings.
EXIT
:
Use this feature to exit OSD menu
15
6. Vehicle Installation
0M 1M 2M 3M
Red Yellow Green
Camera
a. Install Camera R (for rear view)
b. Use a measuring tool to mark out the distance behind the vehicle.
c. Adjust the viewing angle of the camera so that the distance gage shown from
the TFT match to the distance marks behind the vehicle.
16
7. Specification
Screen size 7 inch ( diagonal )
Active area
154.08(H) x 86.58(V)
Pixel configuration
0.107 x 0.370
Resolution
1440(W) x 234 (H)
Viewing angle
UP:60° / Down:60° / Left: 60° / Right:60°
Power source:
DC9.6V ~DC32V
Contrast ratio
300:1
Brightness 400
cd/m
2
Composite Video In
Connector RCA
Input Signal
1Vpp
Impedance 75
Ohms
Camera MINI DIN In
Connector
6 PIN MINI DIN (Standard)
Input video signal level
1Vpp
Impedance
75 Ohms
Input audio signal level
1Vpp
Power output for camera
DC12V 350mA
AV AUDIO IN
Connector RCA
Input video signal level
1Vpp
Impedance
75 Ohms
Composite Video Live Out
Connector RCA
Input signal level
1Vpp
CAM OUT
Connector RCA
Input signal level
1Vpp
Impedance 75
Ohms
Audio LIVE OUT
Connector RCA
Input signal level
1Vpp
Impedance 75
Ohms
Dimension
W x H x D :
192 x140.5 x 51.8mm
Weight N.W./G.W.:
2kg/
2.28kg
Environmental:
Operation temperature
-10
℃
~70
℃
Storage temperature
-30
℃
~80
℃
Humidity 20%-80%
17
8. ATTACHMENT
Attachment 1: Dimension Chart
18