Full Text Searchable PDF User Manual

User’s Manual
Manual del Usuario
Mixer / Amplifiers
GA335
GA460

2
GA335 / GA460
English
INTRODUCTION �������������������������������������������������������������������������������������������������������������������������� 4
FEATURES ����������������������������������������������������������������������������������������������������������������������������������� 4
FRONT PANEL ����������������������������������������������������������������������������������������������������������������������������� 4
REAR PANEL ������������������������������������������������������������������������������������������������������������������������������� 5
INPUT WIRING ���������������������������������������������������������������������������������������������������������������������������� 6
OUTPUT WIRING ������������������������������������������������������������������������������������������������������������������������ 6
SPECIFICATIONS ������������������������������������������������������������������������������������������������������������������������ 7
INTRODUCCIÓN �������������������������������������������������������������������������������������������������������������������������� 9
CARACTERÍSTICAS �������������������������������������������������������������������������������������������������������������������� 9
PANEL FRONTAL ������������������������������������������������������������������������������������������������������������������������� 9
PANEL POSTERIOR ������������������������������������������������������������������������������������������������������������������ 10
ENCABLADO DE ENTRADA ������������������������������������������������������������������������������������������������������11
ENCABLADO DE SALIDA �����������������������������������������������������������������������������������������������������������11
ESPECIFICACIONES ���������������������������������������������������������������������������������������������������������������� 12
APPLICATION / APLICACIONES ��������������������������������������������������������������������������������������������� 13
DIMENSIONS / DIMENSIONES ����������������������������������������������������������������������������������������������� 14
Asystems reserves the right to alter information provided in this document without prior notice�
Asystems se reserva el derecho de mejorar o alterar cualquier información provista dentro de este documento sin previo aviso�
V1�0 07/24/2017
CONTENTS
CONTENIDO
APPENDIX

3
GA335 / GA460
English
1. Read these instructions before operating this
apparatus.
2. Keep these instructions for future reference.
3. Heed all warnings to ensure safe operation.
4. Follow all instructions provided in this document.
5. Do not use this apparatus near water or in locations
where condensation may occur.
6. Clean only with dry cloth. Do not use aerosol or liquid
cleaners. Unplug this apparatus before cleaning.
7. Do not block any of the ventilation openings. Install
in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If
the provided plug does not into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plug, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories
by the
manufacturer.
12. Use only with a cart, stand, tripod, bracket, or
table
by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from tip-
over.
13. Unplug this apparatus during lighting
storms or when unused for long
periods of time.
14. Refer all servicing to
service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is in-
tended to alert the user to the presence of important operat-
ing and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
To reduce the risk of
or electric shock, do
not expose this apparatus to rain or moisture.
CAUTION:
Use of controls or adjustments or performance
of procedures other than those
may result in
hazardous radiation exposure.
The apparatus shall not be exposed to dripping or splashing and that no objects
with liquids, such as vases,
shall be placed on the apparatus. The MAINS plug is used as the disconnect device, the disconnect device shall
remain readily operable.
Warning
: the user shall not place this apparatus in the
area during the operation so that the mains switch
can be easily accessible.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

4
GA335 / GA460
English
INTRODUCTION
Congratulations on your purchase of an Asystems GA
series mixer/amplifier. These mixer/amplifiers can mix up
to four or six individual signals with power output rated at
35 or 60 Watts�
The GA series is ideal for small sound reinforcement
systems� An additional zone 2 output with 8 ohm or 600
ohm output connections is included for versatile side fill or
multi-zone operation� Users are able to set priority VOX
operation with a variable threshold control� A phantom
power supply is included for condenser microphones�
A number of stereo RCA connectors with summed inputs
are onboard for inclusion of music sources� A transformer-
isolated output connection is included with 8 ohms, 70V
and 100V line output application possible� Variable bass
and treble controls are available on the master output�
FEATURES
√ Three-channel mixer/amplifier (GA335)
√ Four-channel mixer/amplifier (GA460)
√
Three output operating modes: 8 ohms, 70V and 100V
√ Output power of 35W or 60W (for the GA335 and
GA460 respectively)
√
Wide frequency response of 70 Hz to 18 kHz ±2dB
√
Low distortion and ultra-low noise level
√
Master bass and treble controls
√
Music-On-Hold output connector
√
Balanced channel 1 input
√
Telephone paging output
√
User-controlled VOX priority
√
+15V phantom power for mics
√
Two or three pairs of RCA input connectors
√ Versatile heat and voltage protection for the amplifier
√
Compact design and low weight
FRONT PANEL
1. Input Level Controls
Controls in the input level control for the corresponding
channels�
2. Master Level Control
This controls the final output level before sending to the
output connectors�
3. Master Output Indicators
The green LED above the Master level control will light up
when the output signal exceeds -40dB indicating that a
signal is present� The red LED indicator will light up when
the output signal reaches high peaks with the potential of
causing distortion�
4. Bass Control
Turning to the right will increase the response of low-
frequency signals (100 Hz) in your main audio signal.
Turning to the left will decrease the response of low-
frequency signals�
5. Treble Control
Turning to the right will increase the response of high-
frequency signals (10 kHz) in your main audio signal.
Turning to the left will decrease the response of high-
frequency signals�
6. Power Button and Indicator
This button turns the GA mixer/amplifier on. When the unit
is turned on, the LED indicator will illuminate to indicate as
such. Be sure that the mixer amplifier is turned on after all
other input sources�
1
2
3
4 5
6
1
2
3
4 5
6

5
GA335 / GA460
Español
REAR PANEL
7. Input Amp Configuration Switches
These DIP switches have a number of different functions.
CH1 MicOn/LineOff
When set to Off, it allows line-
level signal input through channel
1� When set to On, it allows
microphone-level signals through
channel 1�
CH1 Normal
This switch sets channel 1 to
normal, with no priorities�
CH1 Priority
Enables muting of channels when
priority circuit on input 1 is closed�
Connect the priority connection on
Input 1 to microphone’s push-to-talk
function when this is activated�
CH1 VOX
Activating this switch allows
automatic muting when channel 1
input passes the preset threshold
(point 8).
CH1 to Zone 2
Activating this switch sends the
channel 1 input signal to the zone 2
output channel�
CH2 to Zone 2
Activating this switch sends the
channel 2 input signal to the zone
2 output�
Phantom Power
This switch activates phantom
power to the Input 1 input� Phantom
power is required for use with
condenser microphones�
8. Input 1 Terminal
This is a 5-pin Phoenix-type connection with 3 pins for
balanced input signals and 2 connectors for priority
push-to-talk button connection� The input accepts direct
connection of line or microphone inputs as selected by the
mic/line DIP switch (point 7).
9. Input 1 VOX Threshold Control
This control adjusts the level at which the Input 1 signal
should be before other signals are muted� This only works
when the CH1 VOX DIP switch is turned on�
10. RCA Inputs
These inputs accept stereo unbalanced line-level RCA
input signals� The input signals received through these
connectors are summed�
11. Zone 2 / MOH Output and Control
This 4-pin Phoenix-type connector provides two different
output possibilities� The 8 ohm side is for 1W output to
external speakers, while the 600 ohm connectors are for
connecting private branch exchange (PBX) telephone
systems for on-hold music� For further info on wiring, see
the Output Wiring section�
12. Preamp Output Terminal
This balanced 3-pin Phoenix type connection sends the
GA335 and GA460 mixer/amplifier’s signal to external
devices� The output signal level is dependent on the
master level control� For further info on wiring, see the
Output Wiring section�
13. Amplifier Output
Speakers can be connected to this output terminal�
Connections available include COM (common), 70V,
100V and 8 ohms� These input connections can accept
terminal forks up to 10 AWG� For further info on wiring,
see the Output Wiring section�
14. Power Socket
This is for a standard IEC power cable� Please connect
the cable to a suitable AC power outlet� While the GA
series offers a universal power supply, be sure to check
local voltage levels before connecting the unit to ensure
they correspond�
7
8
10
11
12
13
14
9
7
8
10
11
12
13
14
9

6
GA335 / GA460
Español
INPUT WIRING
Asystems recommends that customers use pre-build
balanced line connectors with 22 to 24 gauge cable�
Unbalanced connections could also be used however are
susceptible to noise�
Priority Muting
The Asystems GA mixer/amplifier allows users to mute
background signals in favour of the microphone/line input
1 signal. To use a microphone’s push-to-talk switch, first
connect the mic’s push-to-talk contact switch to the priority
connector of the Mic/Line input� Ensure the VOX Normal
DIP switch is set to OFF and the VOX Priority DIP switch
is set to ON� This enables users to mute all other signals
when the microphone’s push-to-talk button is engaged�
OUTPUT WIRING
Speakers
Outputs can be made to by slipping cable lugs underneath
the output screw terminals� Tighten screws to fasten in
place� Customers may choose to use crimp-on spade lugs�
Asystems recommends that customers use professionally
wired high gauge cables� The plastic cover can be slid
into place to protect connections� It is recommended that
you insulate exposed wires to help prevent against the
possibility of short-circuits� Class 2 wiring is required�
Zone 2 / MOH
External music sources can be sent over phone lines
while a caller is on hold using the Asystems GA series�
Connections can be completed as indicated below using
either the 8 ohm or 600 ohm connections� Connect the
Zone 2/MOH to your telephone system or PBX’s music-
on-hold input�
WARNING:
Do not use shielded cable for output power wiring�
Asystems recommends use of 2-conductor shielded cable and
3-pin Phoenix-type connectors for Preamp Line output�
To telephone system
interface/PBX input

7
GA335 / GA460
Español
GA335
GA460
Power Output (Peak)
35W
60W
Input Section
RCA Input
2
3
1/4” Phone Jack Inputs
3�5mm Mini-Stereo Phone Jack
-
-
Frequency Response
70Hz to 18kHz ±2dB
Phoenix Input
1
1
Link In
-
-
Output Section
Balanced Screw Terminal Output
Yes
Yes
Balanced Phoenix Output
Yes
Yes
Zone 2 (Telephone Use)
Yes
Yes
70V Output
Yes
Yes
100V Output
Yes
Yes
S/N Ratio
All >60dB
All >60dB
Input Signal LED
Yes
Yes
Master Out Clip LED
Yes
Yes
Treble & Bass (Output)
Yes
Yes
Alert & Announce Chimes
-
-
VOX Threshold
Yes
Yes
Number of Input Channels
3
4
Input Volume Control
3
4
Master Out Level Control
1
1
THD@ 1kHz (10% Rated Output)
< 0.5%
< 0.5%
Phantom Power
14~15V
14~15V
Battery Connector
-
-
Dimensions (WxHxD)
241 x 105 x 352 mm (9.49” x 4.13” x 13.86”)
SPECIFICATIONS

8
GA335 / GA460
Español

9
GA335 / GA460
Español
INTRODUCCIÓN
¡Felicitaciones! Por la compra de la mezclador/
amplificador GA de Asystems. Estas mezcladoras/
amplificadoras pueden hacer fusiones de hasta cuatro o
seis señales individuales con salida de potencia estimada
a 35 o 60 Watts�
La serie de GA es lo ideal para sistemas de renforzamiento
de sonidos pequeños� Una salida de zona 2 en adición
con conexión salida de 8 ohm o 600 ohm es incluida para
una operación versátil de rellando lateral o multi-zona�
Los usuarios pueden configurar la operación prioritaria
VOX con controles de umbral variable� Un +15V
suministro de fuente fantasta es incluido para micrófonos
condesadores� Un número de conectres RCA estéreo
suma entradas abordo para la incluir fuentes de música�
Un transformador-aislado salida de conexión es incluido
con 8ohms, 70V y 100V línea de salida de aplicaciones
posibles� Variados controles de bass y treble estan
disponibles en las salidas master�
CARACTERÍSTICAS
√
Tres canales mezclador/amplificador (GA335)
√
Cuatro canales mezclador/amplificador (GA460)
√
Tres salida de modo operativo: 8 ohms, 70V y 100V
√
Salida de potencia of 35W o 60W (para 35 y 60
respectivamente)
√
Ancha respuesta de frecuencia de 70 Hz a 18 kHz
±2dB
√
Baja distorción y nivel de ruido ultra-bajo
√
Master bass y controles treble
√
Usuario-asignable zona 2 salida
√
Entrada canal 1 balanceado
√
Salida de paginación teléfono
√
Controlador-usuario VOX prioridad
√
+15V fuente fantasma para micrófonos
√
Dos o Tres conectores de entrada RCA
√
Protección versatile de calentamiento y voltaje para el
amplificador
√
Diseño compacto y ligero peso
PANEL FRONTAL
1. Controles de Nivel Entrada
Controla el control de nivel de entrada para los canales
correspondientes�
2. Control Master de Nivel
Este controla la salida final de nivele antes de ser enviados
a la salida de conectores�
3. Indicadores de Salida Master
El LED verde sobre el control de nivel Master se iluminará
cuando la señal de salida sobrepase -40dB indicando
que la señal esta presente� El indicador del LED rojo se
encenderá cuando la señal de salida llegue al pico alto
con el potencial de causar distorción�
4. Control Bass
Girando a la derecha incrementará la respuesta de las
señales de baja-frecuencia (100 Hz) en su señal audio
central� Y girando a la izquierda disminuirá la respuesta
de señales de baja-frecuencia�
5. Control Treble
Girando a la derecha incrementará la respuesta de señal
de alta-frecuencia(10 kHz) en su señal de audio central.
Y girando a la izquierda disminuirá las señales de alta-
frecuencia�
6. Botón de Potencia e Indicador
Este botón enciende el mezclador/amplificador GA.
Cuando esta unidad está encendida, el indicador LED
se iluminará para indicarlo� Asegúrese que el mezclador
amplificadora esté encendida después de todas las
fuentes de entrda�
1
2
3
4 5
6
1
2
3
4 5
6

10
GA335 / GA460
Español
PANEL POSTERIOR
7. Interruptores para Configuración del Amp de
Entrada
Estos interruptores DIP tienen un número de diferentes
funciones�
CH1 MicOn/
LíneaOff
Cuando al estar en OFF, permite la entrada
de señal de línea-nivel por el canal 1� Cuando
este en ON, permite señales de micrófono-
nivel mediante canal 1�
CH1 Normal
Este interruptor configura canal 1 a normal, sin
prioridades�
CH1 Prioridad
Activa enmudecimiento cuando el circuito
de prioridad en la entrada 1 está cerrada�
Conecta la conexión prioritaria en Entrada 1
a de funciones en micrófnos de push-to-talk
(PTT) cuando esta activada.
CH1 VOX
Activando este interruptor permite
enmudecimiento automatic cuando la entrada
de canal 1 pasa el umbral predeterminado
(punto 8).
CH1 a Zone 2 Activando este interruptor envia la señal al
canal de salida zona 2�
CH2 a Zone 2 Activando este interruptor de envía la señal de
entrada canal 2 a salida de zona 2�
Fuente
Fantasma
Este interruptor activa la fuente fantasta a la
Entrada 1� La fuente fantasma requiere del
uso de micrófonos condesadores�
8. Terminal de Entrada 1
Esta conexión de 5-pin tipo-Phoenix con 3 pines para
entradas de señales balanceados y 2 conectores para
conexión de botón prioridad a push-to-talk� Esta entrada
acepta conexión directa de línea o entradas de micrófono
seleccionado por el interruptor DIP mic/línea (punto 7).
9. Control de Entrada 1 VOX Umbral
Este control ajusta el nivel en el cual la señal de Entrada
1 debe estar antes que otras señales esten enmudecidas�
Esto solo funciona cuando el interruptor CH1 VOX DIP
esta encendido�
10. Entradas RCA
Estras entradas aceptan entradas de señales stereo
desbalanceadas línea-nivel RCA� Estas entradas de
señales son recibidas por estos conectores estan
sumadas�
11. Zona 2 / MOH (Música en Espera) Salida y Control
Este conectores de 4-pin tipo-Phoenix ofrece dos
diferentes posibilidades de salida� El lado 8 ohm es para
salida de 1W para altavoces externos, mientras que los
conectores de 600 ohm son para conexiones de Ramal
privado de conmutación automática (PBX) de sistema
telefónico para música en espera� Para más información del
encablado, véase en la sección de Encablado de Salida�
12. Terminal de Salida Preamp
Esta conexión balanceada de 3-pin tipo-Phoenix envía
señal al mezclador/amplificador GA335 y GA460 a
dispositivos externos� El nivel de señal de salida es
dependiente en el control de nivel master� Para más
información sobre encablado, véase en la sección de
Encablado de Salida�
13. Salida de Amplificador
Los altavoces pueden ser conectados a este terminal de
salida. Las conexiones disponibles incluye COM (común),
70V, 100V y 8 ohms� Estas conexiones de entrada
puede aceptar terminals fork hasta de 10 AWG� Para
más información del encablado, véase en la sección de
Encablado de Salida�
14. Cable de Potencia
Esta toma se utiliza para enchufar cables de alimentación
estándar IEC� Es esencial que conecte un cable de
alimentación de CA apropiado� Los Mezcladores/
Amplificadores de la serie GA ofrecen opciones de CA
universal, sin embargo debe estar absolutamente seguro
de que el nivel de voltaje local sea apropiado antes de
enchufar el aparato a esa dicha toma�
7
8
10
11
12
13
14
9
7
8
10
11
12
13
14
9

11
GA335 / GA460
Español
ENCABLADO DE ENTRADA
Asystems recomienda a los usarios usar línea de
conectores pre-construidos balanceados con cables de
alambre 22 a 24 � Conexiones desbalanceados puede ser
usado, sin embargo son suceptibles al ruido�
Enmudecimiento Prioritario
El mezclador/amplificador GA de Asystems permite a los
usuarios enmudecer las señales de fonto a favor de la
señal entrada 1 micrófono/línea� Para usar el interruptor
de micrófono push-to-talk, primero conecte el interruptor
de contacto del push-to-talk al conector de prioridad de la
entrada Mic/Línea� Asegúrese del interruptor VOX normal
DIP esté fijada en ON (encendido). Esto permite a los
usuarios a enmudecer todas las otras señales cuando el
botón de push-to-talk este conectada�
ENCABLADO DE SALIDA
Altavoces
Las salidas pueden ser hechas con pasar un terminal de
cable debajo de la salida terminal clema� Apriete los tornillos
en sitio� Los clientes pueden elegir en usar enganches
de terminales de horquilla� Asystems recomienta que los
clientes usen cables de alambres altamente encabalados
profesionales� La covertura plástica puede ser deslizada
en sitio para protejer las conexiones� Es recomendado
que ueste aisle los cables expuestos para prevenir contra
las posibilidades de corto-circuitos� Encablado de Clase
2 es requerido�
Zona 2 / MOH (Música en Espera)
Fuentes de música externa puede ser enviada por las
líneas de teléfono mientras que el llamador están en
espera usando la serie GA de Asystems� Las conexiones
pueden ser completados como se indica abajo, usando
conexiones de 8 ohm o 600 ohm� Conecte Zona 2 / MOH
a su entrada de sistema de telefónico o PBX música en
espera�
ADVERTENCIA: No usar cable apantallado para encablados de
potencia de salida� Asystems recomienda usar 2- conductores
de cable apantallado y conectores de 3-pin tipo-Phoenix Preamp
línea de salida�
A la interfaz del
sistema telefónico/
Entrada PBX

12
GA335 / GA460
Español
GA335
GA460
Salida de Potencia (Pico)
35W
60W
Sección de Entrada
Entrada RCA
2
3
Entradas 1/4” Phone Jack
3�5mm Mini-Estéreo Phone Jack
-
-
Respuesta en Frencuencia
70Hz to 18kHz ±2dB
Entrada Phoenix
1
1
Link In
-
-
Sección de Salida
Salida Balanceada Terminal Clema
Si
Si
Salida Balanceada Phoenix
Si
Si
Zona 2 (Uso Telefónico)
Si
Si
70V Salida
Si
Si
100V Salida
Si
Si
S/N Relación
All >60dB
All >60dB
Entrada de Señal LED
Si
Si
Master Salida Clip LED
Si
Si
Treble & Bass (Salida)
Si
Si
Alerta & Anunciado Chimes
-
-
VOX umbral
Si
Si
Número Entrada de Canales
3
4
Entrada Control de Volumen
3
4
Master Salida Control de Nivel
1
1
THD@ 1kHz (10% Salida Nominal)
< 0.5%
< 0.5%
Fuente Fantasma
14~15V
14~15V
Conector para bateria
-
-
Dimensiones ( An x Alt x P )
241 x 105 x 352 mm
(9.49” x 4.13” x 13.86”)
ESPECIFICACIONES

13
GA335 / GA460
Appendix
APPLICATION APLICACIONES
CD or MP3 Player
Reproductor CD o MP3
To mic talkback switch
A interruptor
mic de talkback
Telephone system
interface / PBX
8Ω Speaker
Altavoz 8Ω
Paging Mic
Mic de paginación
Satellite Receiver
Receptor Satélite
Interfase de Sistema Telefónico/
Entrada Ramal privado de
conmutación automática

14
GA335 / GA460
Appendix
DIMENSIONS
DIMENSIONES
Measurements are shown in mm (inches)
Todas las medidas están mostradas en mm (pulgadas)
241 mm (9.49”)
85.5mm (3.4”)
105mm (4.3”)
352mm (13.86”
)

15
GA335 / GA460
Appendix
NOTES

www�asystems-sys�com