Full Text Searchable PDF User Manual
INSTRUCTION MANUAL
LT18HT
18V
CORDLESS HEDGE TRIMMER
2
Warranty
2
Introduction
3
Environmental protection
3
Description of symbols
3
Specifications
3
General safety rules
4
Additional safety rules for hedge trimmers
5
Additional safety rules for the charger
6
Additional safety rules related
to the battery pack and battery safety
7
When to charge the battery
8
Know your product
9
Unpacking
10
Assembly
10
Important information – product care
10
Fitting and removing the battery pack
11
Battery charging
11
To obtain the best life for the battery
11
Safety features incorporated with tools
using this battery pack
12
Using the hedge trimmer
13
Shaping
13
Cutting
13
Pruning
14
General inspection
14
Maintenance
14
Troubleshooting
14
CONTENTS
Warranty Power Tools
For full details please visit us at www.909.com
3
Description of symbols
The rating plate on your tool may show symbols.
These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Double insulated for additional protection.
Conforms to relevant standards
for electromagnetic compatibility.
For safe operation read instruction manual.
Specifications
Cordless Hedge Trimmer
Model #:
LT18HT
Bar Length:
450mm
Maximum Cutting Capacity:
14mm
No-Load Speed:
1200 SPM
Battery Pack
Model #:
18LGRB
Nominal battery charge:
18 Vdc
Battery cells:
Lithium-Ion 1.5Ah
Plug Pack Charger
Model #:
JY15-225-050
Charger Input:
100–240Vac 50–60Hz
Charger Output:
22.5Vdc 500mA
Adaptor Base
Model #:
18LGRA
Charging time:
3–5 Hour
Introduction
Your new 909 power tool will more than satisfy
your expectations. It has been manufactured under
stringent 909 Quality Standards to meet superior
performance criteria.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
CAUTION.
Carefully read through this entire Instruction
Manual before using your new 909 Power Tool. Take
special care to heed the Cautions and Warnings.
Your 909 power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Environmental protection
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way.
4
General safety rules
WARNING.
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres,
such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way.
Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase
the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord
suitable for outdoor use reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication.
A moment
of inattention while operating power tools may result in
serious personal injury.
b) Use personal protective equipment. Always wear eye
protection.
Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times.
This enables better control of the power tool
in unexpected situations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts.
Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will
do the job better and safer at the rate for which it was
designed.
5
b) Do not use the power tool if the switch does not turn
it on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly
maintained power tools.
f ) Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed.
Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge,
unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
i) Children should be supervised to ensure that they
do not play with the appliance.
5) Battery tool use and care
a) Ensure the switch is in the off position before
inserting battery pack.
Inserting the battery pack into
power tools that have the switch on invites accidents.
b) Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
c) Use power tools only with specifically designated
battery packs.
Use of any other battery packs may
create a risk of injury and fire.
d) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
e) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the
battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This
will ensure that the safety of the power tool is maintained.
Additional safety rules for hedge trimmers
•
Do not use the trimmer in the rain.
•
Keep hands and fingers well away from the blade.
•
Wear work gloves, eye protection, solid shoes and
trousers when using this hedge trimmer.
•
Always grasp both handles when operating the unit.
•
Disconnect the trimmer from the mains supply when
you have finished work, before cleaning or if you have
been interrupted.
•
This trimmer has been designed to cut soft, new growth
and should not be used on branches, hard wood or other
forms of cutting.
6
•
Do not attempt to free a jammed blade before first
switching off the machine and removing the battery pack.
•
If you are interrupted when operating the trimmer,
complete the process and switch off before looking up.
•
Never allow untrained users or children to use
the trimmer.
Wear goggles
Wear ear defenders
Wear a breathing mask
Additional safety rules for the charger
•
Your 909 tool with Lithium-Ion batteries may only
be charged with the specific designed 909 Lithium-
Ion battery charger purchased with the tool.
IT IS
DANGEROUS TO USE ANY OTHER BATTERY
CHARGER TO CHARGE YOUR TOOL.
Do not attempt
to charge the battery pack with any other charger than
the one supplied.
•
If there is a problem with the battery or the tool, take
it to your nearest Authorised Service centre or phone
and speak with an experienced 909 Customer Service
Representative for assistance in rectifying your problem.
•
Before using the charger, read all the instructions, labels
and cautionary markings on the charger and battery pack
as well as the instructions on using the battery pack.
•
Do not use the charger if it has been subjected to a
heavy knock, dropped or otherwise damaged in any way.
Take the charger to an authorised service centre for a
check or repair.
•
Do not disassemble the charger. Phone to speak with
an experienced 909 Customer Service Representative
or contact an Authorised Service centre for assistance.
Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly
can cause electric shock when you use the tool or
charger again. Take the charger to an authorised service
centre when service or repair is required. Incorrect re-
assembly may result in the risk of fire, electric shock or
electrocution. To reduce the risk of electric shock, do not
disassemble any part of the product.
•
DANGER.
If the battery pack is cracked or damaged in
any other way, do not insert it in the charger.
•
Do not plug anything other than your 909 battery pack
into the charger, as other objects may touch dangerous
voltage points or short out parts, which could result in fire
or electric shock.
•
Do not place the tool or charger on an uneven surface,
as a fall may cause serious damage.
•
Never place the tool or charger near or over a heat
source such as a radiator or heater.
•
Do not operate the charger in a cabinet or other
enclosure unless proper ventilation is provided.
•
Use the battery charger indoors only.
WARNING.
Do not allow any liquid to come into contact
with the charger. There is a danger of electric shock. Do not
position the tool or battery charger near water; for example,
near a sink, wash bowl or toilet. Do not spill liquid of any
kind on the tool or charger. Doing so may short out parts,
causing damage to the product and creating the risk of fire
or electric shock.
Take the tool or charger to your nearest Authorised Service
centre or phone and speak with an experienced 909
Customer Service Representative for assistance in these
circumstances:
•
If liquid has been spilled into the tool or charger, or if rain
or water has touched the tool, Battery Pack or charger.
7
•
If the tool or charger does not operate normally after you
follow the operating instructions.
•
If the tool or charger has been dropped or damaged.
•
If the tool or charger exhibits a distinct degradation in
performance.
•
If the tool or charger is damaged in any way.
•
If the battery pack is not charged within the time frame as
specified in this manual, turn charger off.
•
To reduce the risk of an electric shock, unplug the
charger from the power supply before attempting to clean
it. To clean tool or charger, wipe with a damp cloth. Use
of any other cleaners is not recommended.
•
Do not place any object on to, or allow anything to rest
on the charger.
•
Make sure that the charger cable is positioned where
it will not be stepped on, tripped over or otherwise
subjected to damage or stress. Keep the lead away
from operating machinery.
•
Do not pull on the lead of the charger to disconnect it
from the mains power socket.
•
Do not use an extension cord unless it is absolutely
necessary. The use of an improper extension cord could
cause the risk of fire, electric shock or electrocution.
•
Never attempt to connect two chargers together.
•
Do not charge batteries or use the tool and battery
pack in locations where the temperature may be below
0°C or exceed 40°C such as alongside sheds or metal
structures.
•
The battery can be charged or operated at temperatures
between 0° C and 40° C.
NEVER CHARGE YOUR LITHIUM-ION BATTERY
BELOW OR ABOVE TEMPERATURES RECOMMENDED
OTHERWISE FIRE OR SERIOUS DAMAGE TO THE
BATTERY PACK MAY OCCUR.
The most suitable temperatures to charge the battery pack
are between 20–25° C.
•
If you wish to charge a second battery pack, unplug the
charger from the mains supply and leave it for at least
15 minutes. After this time you can charge a second
battery pack.
Additional safety rules related
to the battery pack and battery safety
•
Use only the 909 batteries supplied with the 909 Tool or
909-approved replacements.
•
Do not use the battery to power any device other than
the 909 tool it was sold with.
•
Charge the battery only with the 909 charger supplied
with the tool or 909-approved replacements and
according to the instructions in the 909 Instruction
Manual.
•
Do not charge the battery in a place where static
electricity is generated nor let the battery touch something
that is statically charged.
•
The battery can be stored at temperatures between
– 20° C and 40° C.
NEVER STORE OR LEAVE YOUR LITHIUM-
ION BATTERY IN TEMPERATURES OVER THAT
RECOMMENDED OTHERWISE FIRE MAY OCCUR.
Do NOT store the Lithium Ion battery anywhere that
the temperature can easily reach higher temperatures
than recommended - this includes garden type sheds,
and Vehicles where the inside temperature can climb
to dangerous levels in the direct sunlight and on high
temperature days.
THINK BEFORE LEAVING YOUR
LITHIUM-ION BATTERY PACK IN STORAGE.
•
The battery can be charged or operated at temperatures
between 0° C and 40° C.
NEVER CHARGE YOUR LITHIUM-ION BATTERY
BELOW OR ABOVE TEMPERATURES RECOMMENDED
OTHERWISE FIRE OR SERIOUS DAMAGE TO THE
BATTERY PACK MAY OCCUR.
The most suitable temperatures to charge the battery pack
are between 20–25° C.
8
•
Always allow the battery pack to cool down after
charging, do not place it in a hot environment such as a
metal shed or open trailer left in the sun.
•
Take care where the tool is stored. Do not store in areas
of corrosive fumes, or salt air or similar conditions. Try
and store the tool in the packaging supplied with the tool.
•
Do not dispose of the battery in a fire or put the battery
into a microwave oven, conventional oven, dryer, or high-
pressure container. Under these conditions, the battery
may explode.
•
Never attempt to open the battery pack, puncture the
battery or subject the battery to strong physical shock.
•
If the plastic housing of the battery pack breaks open
or cracks, immediately discontinue its use and do not
recharge it. Ensure the battery pack clip is in good
condition and will not allow the pack to fall free from the
tool. If the clip is damaged or for any reason is not locking
the pack in place Do Not continue to use.
•
Stop using the battery if it exhibits abnormal heat, odour,
colour, deformation, or is in an abnormal condition.
•
If you detect leakage or a foul odour, it is especially
important to keep the battery away from fire. If battery
liquid leaks onto your skin or clothes, wash well with
clean water immediately. If liquid leaking from the
battery gets into your eyes, do not rub your eyes.
Rinse your eyes well (for at least 10 minutes) with clean
water, and consult a doctor immediately. Do not use a
leaking battery.
•
Handle batteries with care to avoid shorting the battery
with conducting materials, such as nails, screws, metal
watch bands, rings, bracelets, and keys. The battery may
overheat and could burn you.
•
After the battery has reached the end of its useful life,
we recommend recycling the materials at your local
municipal council recycling centre. DO NOT attempt to
replace the battery cells in the battery pack, repair or
modify any part of the battery pack assembly
•
When recycling, make it non-conductive by applying
insulating tape to the terminals located on the battery.
When to charge the battery
New battery packs are shipped in a low charge
condition and must be fully charged before use. It takes
approximately 8 hours to fully charge a new battery and
3–5 hours once the battery has been used in the tool
a few times.
Charging of batteries should not be undertaken casually.
Through the charging cycle the condition of the battery pack
should be monitored and the charge cycle turned
off at completion or at the end of the recommended time.
9
Know your product
1. Rear handle trigger switch
2. Front handle bar switch
3. Front handle
4. Battery pack
5. Guard
6. Blade
7. Plug pack charger
8. Charger base adaptor
2
1
4
3
5
6
7
8
10
Unpacking
Due to modern mass production techniques, it is unlikely
that your 909 Power Tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
Assembly
The prior to operation will require some initial assembly.
Prior to carrying out any assembly work, adjustments or
maintenance, ensure the Battery pack has been removed
from the rear of the housing so operation of the trimmer is
impossible.
Fitting the front see-through guard
The front guard fits directly
onto the sides of the main
housing, just at the point
where the blades extend
from the housing.
The guard has a mounting
tab on each side. These
locate onto a recess on each
side of the housing.
Assembly
1. Hold the clear guard on its side, with the mounting tabs
towards you.
2. With the blade of the hedge trimmer pointing away from
you, with the guard still on its side, slide the guard over
the cutting bar directly at the front of the housing.
3. Rotate the guard so the guard sits upright. The two
mounting tab should locate in the side housing recesses.
4. Secure the guard with the two small screws provided,
ensuring the screws are tight.
Note. NEVER
use the hedge trimmer without the front
guard attached.
Important information – product care
This hedge trimmer uses Lithium-Ion battery cells. Care
MUST be taken to ensure both the safety and life of the
pack is maintained. Ensure you have read all of the safety
notes in the previous pages before using the hedge trimmer.
Safety devices and circuitry for this tool are located in
the battery pack of this tool. The battery pack is a vital
component, not just for the power source, but also for
the full safety control for both the charging and also the
tool operation. Treat the battery pack with care and within
the guidelines of this manual. If the pack does become
immersed in water or any fluids, or is subject to a severe
drop etc., or it does not operate within the guidelines of
this manual, immediately STOP using the battery pack
and have it checked.
During operation, avoid overloading the tool. If the tool is
overloaded it will automatically STOP. Overloading may
occur for a number of reasons including when the tool
is pushed too hard. If you do overload the tool during
operation refer to the “Overload” section in this manual.
Note:
When the battery of the tool is at the lower end of the
charge, the tool is more susceptible to the overload condition.
As mentioned above, the battery pack is an integral
component of this tool and is fitted with thermal safety
devices. Running the tool at close to maximum load, or
continual resetting of the overload will cause the battery
pack to over heat. When a preset cell temperature is
detected, the battery pack will automatically STOP
operating and will not restart until the battery pack has
cooled to a safe level.
In this condition, DO NOT force-cool the pack by placing in
a freezer or similar device. Refer to the “
Overload
” section
in this manual.
Another feature of the battery pack is the
low voltage
cut out
feature. This feature operates when the voltage
drops below a preset value. When this occurs the tool
will automatically stop operating. To correct the situation
you need to either insert another charged battery into the
11
trimmer or recharge the existing battery, and then proceed
with the application.
Note:
Attempting to restart the tool in this condition without
either recharging the battery or installing a battery with
charge will lead to it restarting and then stopping again after
only a few seconds of operation.
These safety devices have been fitted for the safety,
reliability and life of the tool.
Fitting and removing the battery pack
To remove the battery pack from the tool or charger base
adaptor, firmly press the
battery release button at
the back of the battery pack
and slide the battery pack
backward, and then pull or
lift the battery out of the tool
handle or base adaptor.
To install the battery pack
into the tool or base adaptor,
align the keys of the battery
pack with the keyway slots in
the tool or base adaptor and
push the battery into the housing. To connect the battery,
slide the battery pack fully forward.
Battery charging
IMPORTANT.
Before plugging in the power supply from the
plug pack charger (7) to the charger base (8) always ensure
that the plug is switched off at the mains.
IMPORTANT.
The battery will be fully charged after approx.
3–5 hours: remove it from the charger after this time.
Do not leave a battery charging for longer than 24 hours.
1. Connect the power output lead from the plug pack
charger (7) to the back of the charger base (8).
2. Connect the plug pack charger (7) to a mains power
outlet (240Vac) and turn on. The indicator light on the
charger base should glow green, indicating power is
available at the charger base adaptor.
3. Align the battery pack (4) with the entry of the charger
base (8). Fully insert the battery.
4. The indicator light should now change from green to red,
indicating the battery is being charged.
5. When the battery is charged, the red light will change
back to a green light.
6. Remove the battery from the charger base and turn off
the plug pack charger. The green light should go off.
To obtain the best life for the battery
Never allow the tool to completely drain the battery and
come to a complete stand still before recharging. The
battery should be placed on charge whenever the battery
is noticeably running down or the tool no longer performs a
task it previously performed. For storage, charge between
50 and 75%. Avoid allowing loose items like screws or nails
etc. to be stored with battery packs as these or similar items
can short battery packs and cause a fire or explosion.
Always unplug the charger when not in use and store in
a dry secure place.
Avoid charging or storing your battery in temperatures
below 0ºC and above 40ºC.
12
Safety features incorporated
with tools using this battery pack
Product overload
These tools are fitted with an overload protection system. If
the tool is excessively forced, or the task being performed
is too great for the tool, the tool will automatically go into
an overload mode. When the tool goes into overload, the
tool will automatically and suddenly STOP. To reset the
overload, simply release the trigger. When the trigger is
pressed again, the tool will restart. Resume work after the
overload has been reset, but reduce the size of the cut or
reduce the force on the tool to make the cut.
CAUTION.
Do not continue to overload the tool and
constantly reset the overload. Doing this will cause the
battery cells to overheat.
Temperature cut out
If the tool is constantly overloaded, or the tool is used
constantly at maximum rating in high ambient conditions,
the battery cells may over heat causing the battery pack to
shut down. The tool will not re-start until the battery pack has
cooled.
If this occurs you will need to immediately stop working and
allow the battery cells to cool down.
To reduce the temperature of the cells remove the battery
pack from the tool and place the battery pack in a free air
environment, out of direct sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in
refrigerators or freezers.
When the battery pack has cooled down it can again
be used to operate the tool, as long as the load or the
conditions causing the original excessive temperature
has been corrected.
Low voltage cut out
The battery pack used on this tool is fitted with a
low
voltage cut out
feature within the circuitry.
The
low voltage cut out
feature operates when the voltage
drops below a preset value. This feature automatically
stops the tool from operating (similar to that of the over
load condition). When this condition occurs you will need
to either insert another battery into the tool or recharge the
existing battery.
The
low voltage cut out
feature has been added to
maximise the tool’s life. When this occurs, recharge the
battery pack by following the battery charging section in
this manual.
Note:
Attempting to restart the tool without either recharging
the battery or installing another battery (with charge) will
lead to the tool restarting and then stopping again, after only
a few seconds of operation.
13
Using the hedge trimmer
Safety features
1. The cutting blade is
supplied with a sheath
type cover. Keep the cover
on the blades when ever
the tool is not being used.
2. When the hedge trimmer
is not being used it is
suggested to remove the
battery pack to prevent
unauthorised use of the
tool.
3. The rear handle trigger switch (1) and front handle bar
switch (2) must be operated together to start the motor.
This ensures that both hands are used to control the
trimmer.
4. If either of the two switches is released, the tool is
designed to stop rapidly.
Switching on and off
1. To switch on, press both
the trigger switch (1) and
the bar switch (2) at the
same time.
2. To switch off, release
either switch.
Safety points during
operation.
•
Wear eye protection when using this tool.
•
Always use two hands to hold the tool. One on the rear
handle and one on the front loop handle.
•
Always ensure good balance. Both feet should be firmly
on the ground.
Shaping
1. Trim a hedge so that it is
wider at the bottom than
the top.
2. This improves light
penetration and promotes
healthy growth.
3. Narrow the hedge
approximately 100 mm for
every metre in height.
4. A bush can be round or
column shaped.
Cutting
1. Assume a secure position,
using two hands to hold the
trimmer and switch on.
2. Trim both sides of the
hedge, starting at the
bottom. This prevents
cuttings falling into the area
yet to be cut.
3. Pass the blade lightly through the surface of the hedge.
Do not attempt to cut too deep.
4. Trim the top of the hedge.
5. For older hedges that
require cutting back
substantially, use pruning
shears to cut the thicker
branches and
then finish the job with the
hedge trimmer.
WARNING.
Do not let the blade come into contact with
fencing wire or any other object that could damage it.
�����
�����
14
Pruning
Your hedge trimmer is versatile. It can also be used for
trimming back new growth from small shrubs onto the
driveway or into the garden.
General inspection
1. Regularly check that all the fixing screws are tight. They
may vibrate loose over time.
Maintenance
1. Store the tool, instruction manual and accessories in a
secure, dry place. In this way you will always have all the
information and parts ready to hand.
2. Keep the tool’s air vents unclogged and clean at all times.
3. Remove dust and dirt regularly. Cleaning is best done
with compressed air or a rag.
4. Never use caustic agents to clean plastic parts.
5. Remove battery from tool during storage.
6. Replace blade cover when the tool is not being used.
CAUTION.
Do not use cleaning agents to clean the plastic
parts of the tool. A mild detergent on a damp cloth is
recommended. Water must never come into contact with
the tool.
Blade maintenance
Wear gloves when handing or cleaning the cutting blade.
Always clean the cutting blade after operation and lubricate
with protective spray. During longer cutting jobs, we
recommend periodically lubricating the cutting blade with
protective spray.
Visually check the condition of the cutting edges of the
cutting blade. Check tightness of blade bolts. Ensure that
the blade is covered with the blade protection supplied.
Lubrication
WARNING.
Switch off and remove the battery before
carrying out any maintenance on the tool.
After each use, clean the blades and lightly lubricate
with general purpose oil or spray lubricant.
Troubleshooting
No power
1. Check the battery if it is
charged or not.
2. Any of the parts are
defective, such as On/Off
switch / motor etc. (please
contact service agent).
The hedge
trimmer operates
intermittently
1. Any of the two handle
switches are defective
(please contact service
agent).
2. Battery is nearly empty.
3. Internal loose electrical
connection.
4. On/Off switch defective
(please contact service
agent).
Motor runs but
blades remain
stationary
1. Internal fault (please contact
service agent).
The blade is not
working
1. Cutting blade blunt (have
blade sharpened).
2. Cutting blade has dents
(have blade overhauled).
3. Too much friction, due to
lack of lubricant (apply
lubricant spray).
15
