Full Text Searchable PDF User Manual
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
1
VISIX V-Series All-in-One Camera – Gen II
VX-3V-ID-RIAWD Quick Start Guide
v01-2017
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
2
Table of Contents
1 CAMERA OVERVIEW .................................................................................................................................... 3
VX-3V-ID-RIAWD
C
AMERA
D
ESCRIPTION
........................................................................................................ 3
Available Mounts ........................................................................................................................................... 4
Installation – Ceiling Mount ........................................................................................................................... 5
2 CAMERA SETUP ........................................................................................................................................... 8
A
VAILABLE
C
AMERA
S
ETUP
T
OOLS
.................................................................................................................... 8
C
AMERA
S
ETUP
-
DHCP
-E
NABLED
N
ETWORKS
................................................................................................... 8
C
AMERA
S
ETUP
-
N
ON
-DHCP
N
ETWORKS
......................................................................................................... 8
R
EMOTE
M
ONITORING AND
V
IEWING
-
A
DDING A
V-S
ERIES
C
AMERA TO
VIGIL
C
LIENT
............................................... 9
R
EMOTE
M
ONITORING AND
V
IEWING
-
A
DDING A
V-S
ERIES
C
AMERA TO
3
X
LOGIC
V
IEW
L
ITE
II
M
OBILE
(A
NDROID AND
I
OS) 10
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
3
1
Camera Overview
VX-3V-ID-RIAWD Camera Description
See below for descriptions of the different camera components.
Figure 1-2
Overview (2)
1
2
3
4
6
8
7
5
Description of Overview 2
Figure 1-1
Overview
Number
Description
Number
Description
1
Black Liner
2
Bubble
3
Lens
4
BNC Interface
5
Reset
6
Status Indicator
7
Test Serial Port
8
Micro SD Card Slot
9
Adapter Plate
10
Side Outlet
10
9
10
9
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
4
The interfaces on the rear panel are shown below:
Figure 1-3
Overview (3)
Description of Overview (3)
Name/Label
Description
LAN
（
PoE
）
10M/100M Self-adaptive Ethernet Port(PoE Supported)
AUDIO OUT/IN
Audio Out/In
CVBS,GND
Auxiliary video output
1A,1B
Alarm Out
D+,D-
RS-485 Interface
IN,GND
ALARM IN
DC12V
Power Supply Interface
（
12 VDC
）
NOTE:
Press and hold RESET for 10s when the camera is powering on or rebooting to restore the default
settings, including the user name, password, IP address, port No., etc.
AVAILABLE MOUNTS
n
D2 Ceiling Flush Mount (3xLOGIC Product #:
VX-FM-D2
)
n
D2 Wall Mount (3xLOGIC Product #:
VX-WM-D2
)
n
D2 Wall Mount w/ Junction Box (3xLOGIC Product #:
VX-WMJ-D2
)
n
Universal Corner Mount (3xLOGIC Product #:
VX-CM
)
n
Universal Pole Mount (3xLOGIC Product #:
VX-POLE
)
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
5
INSTALLATION – CEILING MOUNT
Steps:
Drill the screw holes and the cable hole according to the supplied drill template.
Figure 1-4
Drill Template
NOTE:
(Optional) Routing the cable from the side outlet instead of the cable hole drilled on the ceiling is
possible. Use pliers to remove the part shown in Figure 1-5, and simply route the cables through the side
outlet.
Figure 1-5
Side Outlet
Attach the adapter plate to the ceiling with the supplied screws.
BOTTOM
Hole
2
2
1
1
1
1
Side Outlet
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
6
Figure 1-6
Install the Adapter Plate
Align the mounting base with the adapter plate and rotate the mounting base counter-clockwise to
affix it to the adapter plate, and then secure it by tightening the lock screw.
Figure 1-7
Install the Mounting Base
Adjust the surveillance angle according to the figure below. Panning angle [0~80°], tilting angle
[0~355°], and azimuth angle of the lens [0~355°].
Figure 1-8
3-axis Adjustment
Zoom and Focus Adjustment
: Cameras of this series are equipped with a motor-driven lens. You can
adjust the zoom and focus level on PTZ control panel by visiting the camera via web browser or client
software. See Section 2 for information on identifying and setting up the camera on your network
Please reference the VIGIL Client User Guide or the 3xLOGIc VISIX V-Series Gen II User Manual for
information on adjusting zoom and focus from VIGIL Client or from the camera browser interface
respectively.
Lock
Screw
0~80°
0~355°
0~355°
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
7
Figure 5-1
Zoom and Focus Adjustment via Camera Browser Interface
Attach the black liner to the dome drive.
Attach the bubble to the dome drive and rotate to tighten it
Figure 1-9
Install the Black Liner and Bubble
Tighten the lock screw to complete the installation.
Complete the Installation.
Black Liner
Dome Drive
Bubble
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
8
2
Camera Setup
Available Camera Setup Tools
All V-Series camera models can be quickly setup for recording and remote monitoring out-of-the-box using one
of two tools; either the
3xLOGIC VSX Setup Tool (iOS and Android)
mobile app or
3xLOGIC All-in-One PC Setup
software
,
depending on your network environment.
n
The
3xLOGIC VSX Setup Tool (iOS and Android)
can be installed on a mobile device running Android
or iOS and has been engineered for use in all
DHCP-enabled
networks. This app scans the camera’s QR
code to establish a connection with the camera and pushes configured settings to the camera via the
cloud.
n
The
3xLOGIC All-in-One PC Setup
software must be installed on a Windows PC running on the same
network as the cameras and is intended for use in large-scale deployments or for
non-DHCP
networks
. The app detects cameras at which point an appropriate IP address can be assigned to the
camera to establish external internet connectivity. The app then pushes configured settings to the
selected camera via the cloud.
Camera Setup - DHCP -Enabled Networks
For DHCP-enabled networks where the camera is hardwired or wirelessly connected to the local network,
manual configuration is possible, however the
3xLOGIC VSX Setup Tool (iOS and Android)
is highly
recommended:
1.
Ensure the connected network provides a DHCP address and allows outbound access to the internet.
For installations where DHCP is not available or where the camera is being used with an appliance see
Section 2.3 Camera Setup - Non-DHCP Networks.
2.
Download VSX Setup app from your devices’ app store.
3.
Follow prompts in the VSX Setup app, and scan the camera’s QR to complete configuration and
enrollment.
4.
You will be required to activate the camera by assigning a complex password.
5.
Be sure to remember the VIGIL Connect Alias as well as the username and password you assign to the
camera. These credentials will be required to add the camera to other VIGIL utilities.
6.
Ensure that the camera is configured with the proper time zone, auto daylight savings update and set
for NTP (auto time sync).
7.
The cameras live view will be displayed in the app for final positioning.
8.
Setup results can be emailed upon completion for easy monitoring configuration.
Note:
The V-Series camera will automatically check for updates and format the SD card. Please allow
15 minutes before power cycling the camera.
Camera Setup - Non-DHCP Networks
The
3xLOGIC All-in-One PC Setup
software was engineered specifically for use in non-DHCP networks where
the mobile app (requires DHCP) cannot be used to configure the camera. A laptop connected to the same
network as the camera will be required to discover the camera and assign a valid IP address using the
3xLOGIC
All-in-One PC Setup
.
1.
Download and install the 3xLOGIC All-in-One PC Setup Utility for Windows from:
http://www.3xlogic.com/support-center/software
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
9
2.
Confirm the PC is networked with the cameras then launch the utility. If properly networked, the utility
will automatically detect cameras on the network (click
Refresh
to refresh the list).
3.
Select the desired device from the list of available cameras.
4.
Click IP Setup and assign the desired IP.
5.
Fill out installer and company information.
6.
To activate the camera, you will be required to assign a complex password.
7.
Confirm the camera Live View preview is as desired and click
Continue
.
8.
Adjust any/all camera settings including the camera name and VIGIL Connect alias. Be sure to remember
the VIGIL Connect Alias as well as the username and password you assign to the camera. These
credentials will be required to add the camera to other VIGIL utilities.
9.
Fill out remaining information and complete steps in the setup tool to receive an installation summary
e-mail.
Note:
The V-Series camera will automatically check for updates and format the SD card. Please allow
15 minutes before power cycling the camera.
Remote Monitoring and Viewing - Adding a V-Series Camera to VIGIL Client
Steps:
To interface a V-Series Camera with VIGIL Client:
1.
Launch VIGIL Client (
Local Mode
only; VCM mode will only display Servers from a networked VCM Server)
and select
Servers
from the
Servers
top menu. This will launch the Servers window. VISIX V-Series
devices are considered edge recording devices and thus are recognized as their own VIGIL Server within
the VIGIL suite.
2.
Click
Add
. This will deploy the
Add/Edit VIGIL Server
window.
3.
Enable the
Use VIGIL Connect
option. If connecting using traditional network connection criteria is
desired, enter the cameras
IP Address/DNS Name
and confirm TCP/IP port status.
4.
Enter in the VIGIL Connect alias of the desired V-Series Camera (
VIGILTest1
used in the below example).
Skip this step if using traditional network connection criteria (IP/Port).
5.
Click
Test VIGIL Connect
to confirm the camera can be communicated with through the Connect system
using the provided alias. Skip this step if using traditional network connection criteria (IP/Port).
Figure 2-1
Adding V-Series Camera to VIGIL Client
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
10
6.
If the test is successful, then VIGIL Client can successfully communicate with the Server. Click
OK
at the
bottom of the
Add Server
window after configuring all required fields to save the new Server to VIGIL
Client. For more information on configuring VIGIL Servers, please see
Section 5.1
of the VIGIL Client
Users Guide.
NOTE:
The camera will be visible in the Client treeview and will be represented by a
icon. The
camera video stream can be added to the VIGIL Client viewer in the same manner as VIGIL Server
cameras; Simply extend the camera’s drop-down menu and double click the icon to add it to the
viewer. Alternatively, a user can drag-and-drop the camera stream icon into the desired frame of
the VIGIL Client viewer.
For more information on configuring VIGIL Servers/V-Series All-in-One camera in VIGIL Client, please see
Section 5.1
of the VIGIL Client Users Guide
Remote Monitoring and Viewing - Adding a V-Series Camera to 3xLOGIC View Lite II
Mobile (Android and iOS)
Steps:
1.
To interface a V-Series camera with 3xLOGIC’s View Lite II mobile app, launch the View Lite II app on
your mobile device (Android OS is pictured in the below screenshot, however, the process is identical
in the iOS version).
2.
Open the
Options
side menu and select
Server Configuration
. The Video Source list will display.
Figure 2-2
Opening Video Source Menu
3.
Select VIGIL Server. VISIX V-Series devices are considered edge recording devices, and thus are
recognized as their own VIGIL Server within View Lite II. The VIGIL Server window will now deploy. A
menu of all VIGIL Servers already interfaced with View Lite II will be visible.
Figure 2-3
:
Adding a Video Source - Add Video Source
4.
To add a new instance of a video source, tap the
icon.
5.
Enable
VIGIL Connect
.
Alternatively, if you wish to use traditional network connection criteria, leave
VIGIL Connect
disabled and enter in an
IP/DNS Name
and
Port
info (if using standard network
connection criteria, also ignore step 6 of these instructions) for the device.
6.
Enter in the VIGIL Connect alias for the desired VISIX V-Series camera (VSeriescam1 used in the above
example).
V-Series Camera Quick Start Guide |
VX-3V-ID-RIAWD
12000 Pecos St., Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
11
Figure 2-4
View Lite II - Add/Edit Server Form - Android
7.
Fill in the remaining required fields and tap
Save
to save the V-Series camera to View Lite II. A user
may now add the camera stream to the View Lite viewer using the same process as adding VIGIL
Server, VCM or 3xCLOUD networked cameras.
12000 Pecos St., Suite 290
Westminster, CO 80234
303.430.1969
Toll Free: 877.3xLOGIC
www.3xlogic.com
© 2018 3xLOGIC Inc. All rights reserved.
Information in this document is subject to change without notice. 3xLOGIC and the
3xLOGIC logo are trademarks of 3xLOGIC, Inc. all other trademarks are property of
their respective owners.
Revised: November 29th, 2017