Full Text Searchable PDF User Manual
Quick Start Guide Connecting GPS
Queclink GV-75 / GV-200 / GV-300
Contact technical support of
Queclink:
(from 10 am to 6 pm
local time of Shanghai)
+8 621 510 82 965
support@queclink.com
Contact Technical Support of
Escort:
+7 495 108 68 33
support@fmeter.ru
Contact technical support of
Wialon:
+3 703 799 94 60, +7 499 918 31 86
support@gurtam.com
2
3
Lists settings in the table to copy
(the right button mouse → copy)
Lists settings in the table to copy (the
right button mouse → copy)
Lists settings
Lists settings
We introduce the SIM, connect the antennas (depending on model).
We connect to the computer, feed the GPS
module, write APN settings.
Server configured for Wialon
GV75
GV200
GV300
193.193.165.165
193.193.165.165
193.193.165.165
21127
20420
20479
IP-адрес
Порт
GV-200
GV-300
GV-75
Attention!
some particular configurations
described in the final of this document.
ATTENTION!
any GPS module can be
configured easily and quickly, sending an SMS
with AT command from the configurator
1
2
3
And the interface table entries:
GV75
GV200
GV300
+
+
+
-
-
0.3 to 16 V
+
+
+
1 und.
2 und.
2 und.
RS-232
Analog input
discrete input
(ignition)
discrete input
(negative)
https://yadi.sk/d/_
XzQ7Mit3ZySDs
https://yadi.sk/d/
ifEcZiLv3ZySHG
https://yadi.sk/d/
A7V7d1PR3ZySNA
4
5
Lists settings in the table to copy
(the right button mouse → copy)
Lists settings in the table to copy
(the right button mouse → copy)
Escort TD-600 in RS-232 mode
Escort TD-600 in RS-232 mode
Then configure the digital interface:
For delivery of data from the
sensors, fuel level, the next
box is activated mask
ERI
We deactivate the
SACK. SACK
determines whether the server
should react to the GPS module
with a
SACK
message, receiving
a message from the GPS module.
Attention!!!
For GPS GV-75 this paragraph configurations module applies only
to complete all tuning operations as after activating the operating mode with
the sensor, the only way to re-communicate with the GPS module to modify
or follow the settings it is only through SMS
«aT + GTFRI = gv75,1,0, 0,0000,0000, 30,1000,1000, 18,30,1 ,,,, $ FFFF ‘command
4
5
5
6
7
The wiring diagram of the sensor
Escort TD-600 in RS-232 mode
Lists settings in the table to copy
(the right button mouse → copy)
Escort TD-600 in RS-232 mode
Escort TD-600 in RS-232 mode
Place the Escort TD-600 to RS-232 sensor mode and establish the network address 255
Connect the sensor to the GPS module. Ready. We wialon review the reports
7
8
Disconnect mode operation GPS
module, without forming the
questions by RS-232 to the sensor
(deactivate the box).
6
(The GPS module pairs are connected:
the transmitter of a device with the
receiver of another well Rx_ TX and RX
TX_):
8
9
Connecting the sensor
in analog mode (GV300):
Connecting the sensor
in analog mode (GV300):
Connecting the sensor in analog mode (GV300)
Connecting the sensor in analog mode (GV300)
Model
GV-75
GV-200
GV-300
Description
After activating the operating mode with the sensor (paragraph 6 of this guide), the only way to return
to communicate to modify or further configurations GPS module is only through the SMS command
‘AT + GTFRI = gv75 , 1.0, 0,0000,0000, 30,1000,1000, 18,30,1 ,,,, $ FFFF «
Through a small bridge or band it is necessary to mimic the signal partner availability, or connect the
input DTR (Data Terminal Ready) and output +5 V (contacts 13 and 19 of the GPS module, previously
activating the box output settings).
It is also necessary to connect «earth» signal for the start of counting. Do common with the sensor (18
GV_200 contact common to the TD-600 sensor and power supply).
The first interface 232 (1) is of service through the same terminal configuration is done, the second
serves for operations with external equipment.
No particularities and difficulties