Full Text Searchable PDF User Manual

USER MANUAL
3D printer
Kreator Motion

Welcome
Read the manual of the device, all information will allow you to operate the printer easily.
Welcome among users of
Kreator Motion printer
!
2

Table of contents
23
12
2
3
14
4
5
16
6
8
19
9
21
11
22
3
Welcome
Table of contents
Display
Basic information
Kreator Motion printer
Calibration of the platform
Technical parameters
Printing materials
Installation / Change of filament
Unboxing
Printing
First run
Additional information
Display and controlling
Technical support

Basic information
When printing process do not touch: the model, head of the
working table; failure to comply with this warning may cause burns
and / or deformation of the print,
After completion of the printing wait until the printer
components cool down,
When printing, do not place other objects in the area of
printer as this may damage the printer,
Use gloves and goggles when removing the model from the
platform,
Juveniles can use the printer only under adult supervision,
Additional tools should be kept away from juveniles.
The device is powered by AC 230V / 50Hz. Connect it to a power socket
with a safety pin (earth) to prevent electric shock in the event of fault.
The place of installation should meet the following conditions:
the room must be equipped with ventilation appropriate to its size,
the printer must be placed on a flat, stable surface.
Do not install the device:
outdoors,
in damp or places exposed to flooding,
in the vicinity of flammable materials and heat sources.
Before using the Kreator Motion printer, it is recommended to read the
following instructions.
4

Kreator Motion printer
1 x
1 x
1 x
1 x
1 x
Kreator Motion
3D printer
roll with filament
warranty card
Quick Start
box of tools and a set
of cables
5

Technical parameters
Printing technology
Workspace
Resolution of the print
Precision of positioning
Printing nozzle diameter
Filament diameter (material)
Max temperature of the print head
Max temperature of the platform
Size of the printer
Size of the package
Weight of the device
Shipped weight
Power socket
Operating temperature
Storage temperature
Fused Filament Fabrication
200 x 200 x 190 mm
60 microns
10 microns
0.4 mm
1.75 mm
260 °C
110 °C
519 x 395 x 420 mm
650 x 535 x 563 mm
18 kg
22 kg
230 VAC / 50 Hz
15 - 35
0
C
0 - 35
0
C
6

Technical parameters
1.
1
2
5.
9.
2.
6.
10.
3.
7.
11.
4.
8.
13.
12.
14.
LCD screen
Platform
Power button
Control knob
Working chamber
Power socket
Head with extruder
SD reader
Cover
Table
USB socket
Filament sensor
Chamber with filament
Spool holder
3
9
11
10
13
12
14
4
5
7
8
6
7

Printing materials
3D Kreator offers filaments to the Kreator Motion Printer. They are a guarantee of successful
print and trouble-free operation of the device. For more information visit our website:
www.3dkreator.com
8

Unboxing
1.
2.
3.
4.
Place the box on a flat and
stable surface, then open the
outer box.
Pull out the inner box .
Remove 4 cardboard packa-
ge protectors.
Lift the inner box up until you see
the printer. Put all of the packa-
ging in the larger box - it’ll be use-
ful when transporting the printer.
4x
9
1.
2.
3.
4.

First run
5.
Locate the yellow plastic transport bezel, which protects the head
from moving during transport. It is marked in blue inn the graphic.
6.
Cut the strap and remove it from inside the
printer.
We recommend cutting the strap
on the right side of print head.
10
5.
6.

First run
7.
Remove the box located
under the table - you might
need to use a bit of force
because of the close place-
ment of the boxes.
8.
Plug the power cord into the
socket at the rear of the prin-
ter and plug into an electrical
outlet.
9.
Turn on the printer using the
button located above the po-
wer socket.
10.
The print chamber should
light up blue, which means
that it is in standby mode.
11
7.
8.
9.
10.

Display and controlling
Temperature of the print head: current / set.
Temperature of the print platform: current / set
Printer status
The current position of the table from the zero position expressed
in millimetres.
Current print speed, the value of 100% corresponds to the speed
defined for each g-code file when it is generated. aa
After starting the printer, the display shows
startup screen
.
3DKREATOR
23/ 0
0
23/ 0
0
Z:
5.00
P
R
:
100%
H
1
1.
2.
4.
3.
5.
4 5
2
3
12
Dis. stepper

Display and controlling
Total runtime.
The duration of current print.
The total amount of used material (in meters).
To navigate the menu use the control knob. If you turn it to the right
or left you will move between the lines down or up the menu. Clicking on
the knob means selection of the currently selected tab or acceptance of
the given option.
Turning the control knob will start the
second screen
.
1.
2.
3.
3DKREATOR
o:
0 d 0:08:03
t:
0:01:13
:
0.0 m
F
1
2
3
13

Display
return to the main screen,
the function is available only when a SD card is in the reader, it
allows for selection of the used material, the temperature and
start of printing,
starts the procedure for changing the filament in the printer,
starts the calibration of the platform,
this tab allows the manual control of the device, changing the
temperature of the head and the platform, level of cooling the
printer, print speed, as well as the movement of axes.
Back:
Printing:
Change filament:
Calibration
Manual control:
The main menu displays after clicking
the control knob
14
Back
Change filament
Printing
Calibration

Display
Auto
printer case lights selection:
Auto – automatic, backlight color depends on the
printer
status,
On – white color of backlight regardless of the
printer
status,
Off –backlight off.
turns off the print head and table heater,
turns off the power of all steppers,
advanced settings.
Case lights:
Cooldown:
Dis. steppers:
Advanced:
15
Case lights
Dis. steppers
Cooldown
Advanced

Calibration of the platform
Calibrating the working platform is recommended when
you first start the printer. Calibration of the table consists
of leveling it with respect to the print head by means of
three nuts located underneath the table’s platform. Tighte-
ning them (turning them to the right) lowers the table, while
loosening them (turning them to the left) raises the table.
NOTICE!
During the calibration process the print head heats up to 235°C. Be careful and do not touch the head components.
1
2
3
16

16
Calibration of the platform
From the main menu, select
Calibration
. The print head will travel to the front of the chamber and heat up to
235
o
C. Clean the nozzle with tweezers and choose
Next step
.
The print head will move to the first calibration point, located above nut nr 1. By turning the nut will cause the
printer’s backlight to change color from white to green.
NOTICE!
A green light does not always mean that the printing platform is properly calibrated. If the head moves
to the calibration point and printer light turns green, turn the nut to the right until the light turns white. Then
turn the nut to the left.
A change in the back light from white to green indicates the appropriate level.
Choose
Next step
. The head will travel to the next position.
Repeat the procedure from steps 2 and 3 for the remaining calibration points.
After calibrating the head in the last position, choose
Exit
. The head will travel to the default position. Following
this procedure, the table is correctly calibrated.
1.
2.
3.
4.
5.
6.
17

Installation / Change of filament
NOTICE!
During the process of changing the filament, the print head heats to temperature of 235°C. Be careful and do not
touch the head components.
Before the first print, a spool with filament must be installed in the printer. This option is also used to
change the material to another.
1.
From the main menu, select
Change filament
.
2.
The print head will travel to the front of the cham-
ber and heat up to 235
o
C.
18
Back
Calibration
Change filament
Manual control

Installation / Change of filament
3.
4.
5.
Open the side door of the fila-
ment compartment.
If you load the material for the first time, skip
this step. If you change the filament, remove
the old material from the tube through the
filament sensor inside the chamber and re-
move the spool from the roller.
Prepare the new filament spool–unravel
about 40
cm of material
and make sure that the material is
clean. Then straighten
around 5 cm
of the filament
that you want to load to allow its smooth insertion
into the head. Uneven ends must be cut using a pair
of pliers, which you can find in the toolbox.
19
3.
4.
5.

Installation / Change of filament
6.
7.
8.
9.
Load the material into the fi-
lament sensor located inside
the filament compartment.
Continue to load about 40
cm of it until you clearly feel
resistance.
Choose the
Insert filament
option from
the menu repeatedly while at the same
time pushing the filament at the opening
of the sensor. The extruder should draw
the material, resulting in a mild increase
in the filament’s downforce. Choose the
option Insert filament until the material
comes out of the print head. Remove ex-
cess filament with tweezers.
Place the roll of material
on the roller and close the
door of the filament com-
partment.
From the menu, select
Exit
.
Following this procedure, the
printer is ready to print using
the new filament.
20
6.
7.
8.
9.
Back
Finish

Printing
Perform calibration of the platform with a procedure which can be found in this manual (page 16)
Instal material in your printer (page 18)
Insert the SD card into the reader located at the lower right corner of the device.
From the main menu select
.
From the menu, choose the type of material used, followed by the file that you want to print.
The printer will warm the head and print platform to the setpoint temperatures, after which it will begin to print.
1.
2.
3.
4.
5.
6.
Printing with 3DKreator is easy.
Follow these guidelines to create three-dimensional models:
21
20

Additional information
Each time you print, clean the table with the remains of the filament and other dirt. It has a big impact on the proper
bonding of layers of the material in the initial stage of printing. Use spatula and dry cloth.
Filament should be stored according to manufacturers guidelines.
It must be clean and dry place. Contact with moisture and dirt may negatively affect its properties and result in pro-
blems with the device. Malfunctions caused by the use of low-quality filament are not covered by the warranty.
The success of print largely depends on its base. It is worth watching the process of applying few initial layers. If they
are fully set on the platform, we can be confident that the further printing process will be conducted properly.
Do not heat the print head when fans are off, it may cause a damage of the printer.
22

Technical support
For more information on operating the device please visit our website:
www. 3dkreator.com
In case of problems and ambiguities related to the use of Kreator Motion printer, please contact us at
support@3dkreator.com
, please quote the serial number of the device or use the form available on the website
www. 3dkreator.com
23