Full Text Searchable PDF User Manual
1
3C
OM
®
S
WITCH
4500
Q
UICK
R
EFERENCE
G
UIDE
About the Web Interface
This guide details the commands available on the Web and the Command Line Interfaces. The tables contained in
this document reference the CLI commands and the equivalent Web Interface menu items that allow the same
configuration to be made using the web interface.
About the Command Line Interface
To use the command line interface (CLI) of your unit, please refer to the following points for assistance:
■
When initially accessing the CLI, press Enter when prompted. The User View displays. This is indicated by the
chevron brackets around the name of the unit at the prompt, for example,
<4500>
.
■
In System View, square brackets appear around the name of the unit at the prompt, for example,
[4500]
.
■
You must be in the System View menu to access the configurable CLI commands.
■
Some commands can be entered directly at any prompt from anywhere in the interface.
■
If you enter part of a command followed by a
?
(with no space between), the CLI will show you all the
commands that begin in that way.
■
To display command parameters:
At the prompt, enter the name of the command followed by a space and
?
. For example:
<4500>
boot ?
The following parameters are displayed:
boot-loader
bootrom
<4500>
To specify boot loader, enter the command as follows:
<4500>
boot boot-loader ?
You only need to enter
?
if parameters exist for the command.
■
To display parent menus:
At the prompt, enter
quit
.
■
To display the User View menu:
Press <CTRL+Z>.
■
To obtain help:
At the prompt, enter
?
.
■
The term ‘view’ may be used interchangeably with the term ‘menu’.
■
The
undo
command is placed before the command you wish to undo, for example,
undo set
authentica-
tion
password.
■
<CTRL+A> places the cursor back to the start of the command line.
■
Enter the first few characters of a command and press TAB to enter the full command without having to
input the entire command (where there is only one command that starts with the entered characters).
■
Use the Up Arrow key at the prompt to repeat the previous command string.
■
Use Delete to delete the character after the cursor; Backspace deletes the character before the cursor.
■
When entering physical port numbers, Enter the port number as
x/0/z
, where x is the unit number and z is
the physical port number.
2
Further Information
For further information about how to use the command line interface, refer to the Command Reference Guide and
the Configuration Guide, which are both available as PDF documents on the CD that accompanied the unit.
Menus
This section provides a summary of menus and commands supported by the agent for each of the supported
hardware platform variants. Any matching web commands available in the web interface are also shown.
Commands marked with ‘*’ are available on the Switch 4500 PWR only.
Table 1
Command Line Editing
Table 2
Commands Available in Any View
<Ctrl+A>
Moves the cursor to the start of the command line
<Tab>
Command completion
Command
Description
Web Command
?
Help
display
Display current system information
display acl
View detailed configuration information about the ACL
display am
View the status of access management function
display arp
View the ARP mapping table
display arp timer aging
View the current setting of the dynamic ARP map aging timer
display boot-loader
View the APP file used for this boot and the one that will be
used at next boot
display channel
View details about the information channel
display clock
View the date and time
display config-agent
View statistics of the configuration agent
display connection
View the connection information of all or specified users
display cpu
Display the occupancy of the CPU
display current-
configuration
Display the current configuration parameters
display debugging
View the enabled debugging process
display device
Display device information
display dhcp client
View detailed information about address allocation to DHCP
client
display dhcp-server
View information about DHCP server group
display dhcp-server
interface vlan-interface
View information about the DHCP server group
corresponding to the VLAN interface
display diagnostic-
information
View the current configuration information about all running
modules
display domain
View the configuration of ISP domains
display dot1x
View the relevant information of 802.1x
display fan
View the working state of the built-in fans
display fib
View the summary of the Forwarding Information Base
display fib ip_address
View the FIB entries matching a destination IP address (range)
display fib acl
View the FIB entries matching a specific ACL
display fib ip-prefix
View the FIB entries matching a specific prefix list
display fib statistics
View the total number of FIB entries
display ftm route
Display Fabric topology management route
display ftm information
Display Fabric topology management information
display ftm topology database
Display Fabric topology management database
display ftp-server
View the parameters of the current FTP server
display ftp-user
View the parameters of current FTP user
3
display history-command
View the saved history of commands
display icmp statistics
View the statistics information about ICMP packets
display igmp-snooping
configuration
View IGMP snooping configuration information
display igmp-snooping group
View IP multicast groups and MAC multicast groups
display igmp-snooping
statistics
View the statistics information on IGMP snooping
display info-center
View the configuration of system log and the information
recorded in the memory buffer
display interface
View port configuration information
Port -> Statistics
display interface vlan-
interface
View the information about specified or all VLAN interfaces
display ip host
View all the host names and the corresponding IP addresses
display ip interface vlan-
interface
View the information of an IP interface
display ip ip-prefix
View the IP address prefix list
display ip socket
Display the information about the sockets in the current
system
display ip statistics
View the statistics information about IP packets
display ip routing-table
View the routing table summary
display ip routing-table
X.X.X.X
View the routing information of the specified destination
address
display ip routing-table
X.X.X.X X.X.X.X
View the routing information in the specified destination
address range
display ip routing-table acl
View the route filtered through specified basic access control
list (ACL)
display ip routing-table ip-
prefix
View the route information that passed the filtering rule
according the input ip prefix list name
display ip routing-table
protocol
View the route information of specified protocol
display ip routing-table
radix
View radix tree of routing table
display ip routing-table
statistics
Summary statistics of all routes
display ip routing-table
verbose
Detail information of routing table
display isolate port
View port isolation information
display lacp system-id
View actor system ID
display link-aggregation
interface
View detailed link aggregation information at a designated
port
display link-aggregation
summary
View summary information of all aggregation groups
display link-aggregation
verbose
View detailed information of a designated port
display local-user
View the relevant information of all (or specified) local users
display local-server
statistics
View the configuration information of local RADIUS server
group
display loopback-detection
View if port loopback detection has been enabled and details
display mac-address
View MAC address table information
display mac-address aging-
time
View the aging time of the dynamic entry in the MAC
address table
display mac-authentication
Display the global information on centralized MAC address
authentication
display memory
Display memory information
display mirror
View port mirroring configuration
Command
Description
Web Command
4
display ntp sessions
NTP connection
display ntp status
NTP status and configuration information
display ntp trace
Trace the time synchronization information
display packet-filter
interface
View active ACL interface information
display packet-filter unit id
View active ACL unit identifier
display password-control
Display password-control information
display password-control
blacklist
Display blacklist information
display password-control
super
Display super user's password-control information
display poe disconnect*
Display PoE Disconnect Mode
display poe interface*
Specify interface e1, 0, n
display poe powersupply*
Display PoE Power Supply Status
display port
View ports where link type is Hybrid, Trunk, or a combination
display power
View the working state of the built-in power supply
display qos cos-local-
precedence-map
View "COS->Local-precedence" map
display qos-interface [x]
View QoS setting information of all interfaces. X = unit
number or interface information (E1,0,1)
display qos-interface [x]
line-rate
View the parameter setting of traffic rate limitation in the
interface output direction. X = unit number or interface
information (E1,0,1)
display qos-interface [x]
mirrored-to
View the settings of the traffic mirro X= unit number or
interface information (E1, 0, 1)r
display qos-interface [x]
traffic-limit
View the settings of traffic limit. X= unit number or interface
information (E1,0,1)
display radius
View the configuration information of all RADIUS server
groups or a specified one
display radius statistics
View the statistics information of RADIUS packet
display remote ping
Display the remote-ping test historay and the latest test
results.
display remote-ping history
Display remote-ping history table
display remote-ping results
Display remote-ping results table
display rip
View the current RIP running state
display rmon alarm
View RMON alarm information
display rmon event
View RMON events
display rmon eventlog
View RMON event log
display rmon history
View the latest RMON history sampling information
display rmon prialarm
Display alarm information about extended RMON
display rmon statistics
View RMON statistics
display route-policy
View the configured route policy
display router id
Display the router’s ID
display rsa local-key-pair
public
Display local key pair and public key of the server
display rsa peer-public-key
Display a designated RSA public key
display saved-configuration
View configuration files stored in flash memory of the Switch
display schedule reboot
Display the configuration of the schedule reboot terminal
service parameters of the current router
display snmp-agent
View information about the SNMP-agent engine ID of current
device
display snmp-agent community
View the currently configured community names
Command
Description
Web Command
5
Table 3
User View
<4500>
display snmp-agent group
View group name, safe mode, state of various views and
storage modes
display snmp-agent mib-view
View the MIB view configuration information of the Switch
display snmp-agent
statistics
View current state of SNMP communication
display snmp-agent sys-info
View the system information of SNMP configuration
display snmp-agent usm-user
View information of all the SNMP usernames in the group
username list
display ssh server status
Display the SSH server status information
display ssh server session
Display SSH server session information
display ssh server-info
Display SSH Server information
display ssh user-information
Display information of about the user, including username,
corresponding key, and authentication type
display startup
Display configuration filenames used for system start-up.
display stop-accounting-
buffer radius-scheme
View the stop accounting buffer radius-scheme requests
display stop-accounting-
buffer session id
Display the stop accounting session identifier
display stop-accounting-
buffer time-range
View the stop accounting time range
display stop-accounting-
buffer user-name
Display the stop accounting user name
display tcp statistics
View the statistics information about TCP packets
display tcp status
View the TCP connection state
display this
Display the running configuration of the current view
display udp-helper server
View the information of destination Helper server
corresponding to a VLAN interface
display udp statistics
View UDP traffic statistic information
display unit
View information about the port in a specific unit. Specify
unit number and interface.
display user-interface
View information about the user interface
display users
View information about the current user interface
display version
Display software version, issue date and the basic hardware
configurations
display voice vlan oui
Display the OUI address supported by the current system
display voice vlan status
Display information about Voice VLAN features
display vlan
View information about the specified or all VLANs
display xrn-fabric
View the information of the entire xrn fabric
quit
Exit from current command view
super
Assign user a higher user level.
return
Return to user view from any view other than user view
tracert
Check the network routes and troubleshoot the network
Command
Description
Web Command
boot boot-loader
Specify the application file (.app) used for booting the Switch
boot bootrom
Upgrade bootrom
cd
Change the current directory
clock datetime
Configure the current date and time
clock summer-time
Configure summer time on the Switch
Command
Description
Web Command
6
clock timezone
Configure local timezone
copy
Copy from one file to another
debugging
Enable system debugging functions
debugging arp packet
Enable ARP debugging
debugging dhcp client
Enable DHCP client debugging
debugging dhcp-relay
Enable DHCP relay debugging
debugging lacp packet
Enable LACP packets debugging at a designated port or ports
debugging lacp state
Enable LACP state machines debugging on a designated port
or ports
debugging link-aggregation
error
Enable link aggregation errors debugging
debugging link-aggregation
event
Enable link aggregation events debugging
debugging mac-authentication
event
Enable the centralized MAC address authentication
debugging switch
debugging ssh server
Display debugging information in running SSH
debugging udp-helper
Enable UDP Helper debugging
delete
Delete a file
dir
List files on a file system
display snmp-agent local-
engineid
Display the engine ID of the local SNMP entity
display system-guard
Display system-guard module options
fabric save-unit-id
Save Unit ID
format
Format the storage device on the Switch
free user-interface
Reset a specified user interface
ftp
Establish control connection with the remote FTP Server and
enter FTP Client View (See
Table 10, “FTP Client View,” on
page 13
)
language-mode
Specify the language environment
lock
Lock current user terminal interface
mkdir
Create a new directory
more
Display the contents of a file
move
Move the file
ping
ping another station
pwd
Display current working directory
reboot
Reset switch
Administration -> Reboot
rename
Rename a file
reset acl counter
Clear ACL statistics
reset arp
Reset ARP mapping entries
reset counters interface
Reset statistical information on the port
reset dot1x statistics
Reset 802.1x statistics information
reset igmp-snooping
statistics
Reset IGMP Snooping statistics information
reset ip statistics
Clear IP statistics information
reset lacp statistics
Clear LACP statistics at a designated port or all ports
reset logbuffer
Reset information in log buffer
reset password-control
history-record
Reset password history record
reset password-control
history-record super
Reset the super user's password controls
reset password-control
blacklist
Delete infomation in blacklist
Command
Description
Web Command
7
Table 4
System View
<4500>
sys
reset radius statistics
Clear the statistic information related to the RADIUS protocol
reset recycle-bin
Delete contents of recycle bin
reset saved-configuration
Delete configuration files
Administration -> Initialize
reset stop-accounting-buffer
Delete the stopping accounting requests from the buffer
according to the specified RADIUS server name
reset stp
Clear statistics for STP
reset tcp statistics
Clear TCP statistics information
reset trapbuffer
Reset information in trap buffer
reset udp statistics
Clear UDP statistics information
rmdir
Delete an existing directory
save
Save current configuration
Save Configuration
schedule reboot at
Schedule a reboot of the Switch at specified time
schedule reboot delay
Configure the Switch to be rebooted after a specified time
delay
send
Send information to other user terminal interface
startup bootrom-access
enable
Enable BOOTROM access
startup saved-configuration
Configure the configuration file used for starting the system
Administration -> Restore
Configuration
system-view
Enter the system view (See
Table 4, “System View,” on
page 7
)
telnet
Establish one Telnet connection
terminal debugging
Configure to display the debugging information on the
terminal
terminal logging
Enable terminal log information display
terminal monitor
Enable the log debugging/log/trap on the terminal monitor
terminal trapping
Enable terminal trap information display
tftp get
Download a file from the specified directory of the TFTP
server
Administration -> Restore
Configuration
tftp put
Upload a file from the Switch to the specified directory on the
TFTP server
Administration -> Backup
Configuration
undelete
Recover a deleted file
undo
Cancel the current setting
xmodem
Establish an xmodem connnection
Command
Description
Web Command
acl number
Define ACL identified by a number or a name, and then enter
the corresponding ACL view (See
Table , “
[4500]rip
,” on
page 17
)
Device -> ACL
Security-> Authorized IP
am enable
Enable the access management function
am trap enable
Enable the access management trap
arp check enable
Enable the checking of ARP entries
arp static
Configure the static ARP mapping entries in an ARP mapping
table
arp timer aging
Configure the dynamic ARP aging timer
change unit-id
Change the ID of the Switch
change self-unit
Change the ID of the Switch
command-privilege level
Specify the command level
copy configuration
Copy source port configuration to destination port
cut connection
Disconnect a user or a category of users by force
Command
Description
Web Command
8
delete static-routes all
Delete all the static routes
Device -> IP Route
dhcp-server [x] ip
Configure the IP address of the DHCP Server used by the
DHCP Server group. X= group number
domain
Configure an ISP domain or enter the view of an existing ISP
domain
dot1x
Specify 802.1x configuration information
dot1x authentication-method
Specify authentication method for 802.1x users
dot1x dhcp-launch
Trigger system authentication when receiving DHCP packet(s)
dot1x max-user
Specify maximal on-line user number per port
dot1x port-control
Specify port authenticated status
dot1x port-method
Specify port controlled method
dot1x quiet-period
Enable quiet period timer
dot1x retry
Specify maximal request times
dot1x supp-proxy-check
Check whether user(s) access the networks by proxy or not
dot1x timer
Specify timer parameters
dot1x timer handshake-period
Set the handshake period of 802.1x
end-station polling ip-
address
Configure the Switch to periodically test specified end-
stations by sending PING packets
execute
Run the batch file
fabric-port [x] enable
Specify the fabric port of the Switch. Specify x = Gig interface
Port -> Administration
file prompt
Modify prompt modes of file operations
ftm stacking-vlan
Specify the stacking VLAN of the Switch
Device -> XRN Fabric
ftp server
Start or shutdown the FTP server
ftp timeout
Configure the FTP connection timeout interval
header
Define the login banner
igmp-snooping enable
IGMP snooping enable
Device -> IGMP Snooping
igmp-snooping disable
IGMP snooping disable
igmp-snooping host-aging-
time
Configure the port aging time of the multicast group
members
igmp-snooping max-response-
time
Configure the maximum response time for a query
igmp-snooping router-aging-
time
Configure the router port aging time of IGMP Snooping
info-center channel name
Rename a channel
info-center console channel
Configure the channel through which log information is
output to the console
info-center enable
Enable the system log
info-center logbuffer
Configure to output information to the memory buffer
info-center monitor channel
Configure the channel to output the log information to the
user terminal
info-center snmp channel
Specify new channel for transmitting the SNMP information
info-center source
Add or delete a record to the information channel
info-center switch-on
Turn on the information synchronization on the specified
Switch
info-center timestamp
Configure the timestamp output format in debugging/trap
information
info-center trapbuffer
Output information to the trap buffer
interface Gig Ethernet
Enter Ethernet Port View (See
Table 15, “Ethernet Port View,”
on page 15
)
interface vlan-interface
Enable VLAN interface and enter VLAN interface view (See
Table 14, “VLAN Inteface View,” on page 14
)
Device -> VLAN Interface
Administration -> IP Setup
ip host
Configure the host name and the host IP address
Command
Description
Web Command
9
ip http
Configure HTTP
Security -> Authorized IP
ip ip-prefix
Configure an address prefix list or one of its items
ip route-static
Configure a static route
Device -> IP Route
lacp system-priority
Configure LACP system priority value
Port -> LACP
link-aggregation group [x]
description
Configure a descriptor for an aggregation group
Port -> Link Aggregation
link-aggregation group [x]
mode
Create a manual or static aggregation group. X=1-32
Port -> Link Aggregation
local-server
Specify local RADIUS server configuration information
local-user
Specify local user configuration and enter local-user view (See
Table 5, “Local-user View,” on page 11
)
Administration ->
System Access
local-user password-display-
mode
Specify password display mode
loopback-detection enable
Enable port loopback detection
loopback-detection interval-
time
Configure the detection interval for the external loopback
condition of each port
mac-address
Configure MAC address
mac-address timer
Configure the aging time of the Layer-2 dynamic address
table entry
mac-authentication
Enable the centralized MAC address authentication feature on
a specified port or globally
mac-authentication authmode
Specify MAC authenticate authmode config
mac-authentication
authpassword
Specify the fixed password
mac-authentication
authusername
Specify the fixed username
mac-authentication domain
Configure the ISP domain used by the centralized MAC
address authentication user
mac-authentication timer
Configure timer parameters of the centralized MAC address
authentication
memory auto-establish
Free memory for routing protocols to run normally
memory limit
Specify the memory limit
memory safety
Display memory safety
ntp-service access
NTP access control
ntp-service authentication
Authenticate NTP timie source
ntp-service authentication-
keyid
Specify NTP authentication keyid
ntp-service max-dynamic-
sessions
Specify the maximum connections
ntp-service reliable
Specify trusted keyid of NTP
ntp-service source-interface
The interface correcponding to the sending NTP packet
ntp-service unicast-peer
Specify the NTP peer
ntp-service unicast-server
Specify the NTP server
password-control
Specify password controls
password-control super
Super user's password controls
poe disconnect*
Set PoE disconnect mode
poe legacy enable*
Enable Legacy detection
poe power-management*
Power Management
poe update*
Update PoE firmware
private-group-id
Tunnel Private Group ID attribute description mode
qos cos-local-precedence-map
Configure “CoS Local-precedence” mapping table
radius nas-ip
Specify the source address of the RADIUS packet sent from
NAS
Command
Description
Web Command
10
radius scheme
Specify RADIUS configuration information and enter the
RADIUS view (See
Table 11, “RADIUS Server Group View,” on
page 13
)
remote-ping
Specify the remote-ping test class
remote-ping-agent enable
Enable a remote-ping client
return
Return to user view from any view other than user view
rip
Enable RIP and enter RIP view (See
Table 17, “RIP View,” on
page 17
)
rmon alarm
Add an entry to the alarm table
rmon event
Add an entry to the event table
rmon prialarm
Add an entry to the extended RMON alarm table
route-policy
Specify a route policy and enter route policy view (See
Table 16, “Route Policy View,” on page 16
)
rsa local-key-pair create
Create local RSA host key pair and server key pair
rsa local-key-pair destroy
Remove all RSA key pairs at the server, including host key pair
and Server key pair
rsa peer-public-key
Enter the public key view (See
Table 8, “Public Key Edit
View,” on page 12
)
set unit “[name]”
Set the unit number name. “[name]”= text string
sftp server enable
Enable SFTP Server
snmp-agent community
Configure community access name and access to SNMP
Administration -> SNMP ->
Community String
snmp-agent group
Configure an SNMP group
Administration -> SNMP ->
Group
snmp-agent local-engineid
Configure a name for a local or remote SNMP engine on the
Switch
snmp-agent mib-view
Create or update the view information
snmp-agent packet max-size
Specify the size of an SNMP packet
snmp-agent sys-info
Configure system information of running SNMP
snmp-agent target-host
Configure destination of SNMP notification
Administration -> SNMP ->
Traps
snmp-agent trap enable
Enable/disable the device to send Trap messages
Administration -> SNMP ->
Traps
snmp-agent trap life
Configure the timeout of Trap packets
snmp-agent trap queue-size
Configure the information queue length of Trap packets sent
to the destination host
snmp-agent trap source
Configure the source address for sending Trap packets
snmp-agent usm-user
Configure users in an SNMP group
Administration -> SNMP ->
Users
ssh2
Establish one telnet connection
ssh client (SSH server IP
address or name) assign rsa-
key (key name)
Assign the SSH client an RSA Key
ssh client first-time enable
Set SSH client attribute of authenticating user for the first
time access
ssh server authentication-
retries (number of retries,
1-5)
Define SSH authentication retry times value
ssh server timeout (value in
seconds, 1-120)
Define timeout value for SSH registration authentication
ssh user (username) service-
type sftp
Set SSH User service types, either stelnet, sft, or all. All is both
stelnet and sftp.
ssh user (sername) assign
rsakey (key name)
Associate an existing public key with a designated user
Command
Description
Web Command
11
Table 5
Local-user View
[4500]
local-user admin
ssh user (username)
authentication-type
(authenticaltion type)
Define an authentication type for a designated user; either
password, RSA, or public key.
stp
Enable Spanning Tree Protocol
Device -> Spanning Tree
stp bpdu-protection
Enable BPDU protection
Device -> Spanning Tree
stp mcheck
Force the port to work in RSTP mode
stp mode
Configure the RSTP running mode
Device -> Spanning Tree
stp pathcost-standard
Standard to be used for calculating the default Path Cost
stp priority
Configure the bridge priority of the Switch
Device -> Spanning Tree
stp root primary
Configure the current switch as the primary root of a
spanning tree
Device -> Spanning Tree
stp root secondary
Configure the current switch as a secondary root of a
specified spanning tree
Device -> Spanning Tree
stp timeout-factor
Configure multiple of hello time
stp timer forward-delay
Configure the time of forward delay
Device -> Spanning Tree
stp timer hello
Configure hello time for Switch
Device -> Spanning Tree
stp timer max-age
Configure the max age of the Switch for judging stp packets
Device -> Spanning Tree
super password level
Configure a password for changing the user from a lower
user level to a higher user level
sysname
Specify the name of the Switch
Administration -> SNMP ->
Setup
system-guard
Configure the System-guard feature
tcp timer fin-timeout
Configure the TCP finwait timer
tcp timer syn-timeout
Configure the TCP synwait timer
tcp window
Configure size of transmission and receiving buffers of
connection-oriented socket
tftp-server
Configure the TFTP server
udp-helper enable
Enable UDP Helper function
udp-helper port
Configure the UDP port with relay function
user-interface
Configure the user terminal interface and enter the view (See
Table 6, “User-interface view,” on page 12
)
vlan
Configure VLAN and enter VLAN view (See
Table 13, “VLAN
View,” on page 14
)
Device -> VLAN
voice vlan
Globally enable the Voice VLAN features of one VLAN
Device -> Voice VLAN
voice vlan aging
Configure the aging time of Voice VLAN
Device -> Voice VLAN
voice vlan mac_address
Set the MAC address that the Voice VLAN can control
Device -> Voice VLAN
voice vlan mode auto
Set the Voice VLAN in auto mode
Device -> Voice VLAN
voice vlan security enable
Enable the Voice VLAN security mode
Device -> Voice VLAN
web set-package
Change the default web source file name
xrn-fabric authentication-
mode
Configure authentication mode of the fabric
Device->XRN Fabric
Command
Description
Web Command
attribute
Configure some attributes for specified local user
Administration -> System
Access
level
Configure user priority level
Administration -> System
Access
password password-control
aging
Specify password aging
Administration -> System
Access
password-control length
Specify password length
Command
Description
Web Command
12
Table 6
User-interface view
[4500]
user-interface 1
Table 7
VTY User-interface View
[4500]
user-interface 1 integer (0-12)
[4500]
user-interface 1 aux
[4500]
user-interface 1 vty
Table 8
Public Key Edit View
[4500]
rsa peer-public-key switchxxx
(where
xxx
is the Switch number)
Table 9
Public Key View
service-type
Configure a service type for a particular user
state
Configure the state of the current user
Command
Description
Web Command
acl
Reference ACL and implement the ACL control to the TELNET
users
Security -> Authorized IP
authentication-mode
Configure local password authentication method
auto-execute command
Configure to automatically run a specified command after a
user logs on
databits
Configure the data bits for AUX (Console) port
flow-control
Configure the flow control mode on AUX (Console) port
history-command max-size
Configure the size of the history command buffer
idle-timeout
Configure the timeout function
parity
Configure the parity mode on AUX (Console) port
protocol
Set user interface protocol
screen-length
Configure how many lines can be displayed on a screen of
the terminal
set authentication password
Configure the password for local authentication
Administration -> System
Access
shell
Enable terminal service of a user interface
speed
Specify the transmission rate on the AUX (Console) port in
bit/s
stopbits
Configure the stop bits on the AUX (Console) port
user privilege level
Configure which level of command a user can use after logon
from a specific user interface
Command
Description
Web Command
protocol inbound
Configure the protocols supported by a designated user
interface
Command
Description
Web Command
public-key-code begin
Enter public key edit view (See
Table 8, “Public Key Edit
View,” on page 12
)
public-key-code end
Save the configured public key and return to the public key
view
Command
Description
Web Command
peer-public-key end
Finish editing peer public key and quit from public key view
to system view
Command
Description
Web Command
13
Table 10
FTP Client View
<4500>
ftp xxx.xxx.xxx.xxx
(where
xxx.xxx.xxx.xxx
is the IP address of the FTP server)
Table 11
RADIUS Server Group View
[4500]
radius scheme 1
Command
Description
Web Command
ascii
Configure FTP data transmission mode as ASCII mode
binary
Configure FTP data transmission mode as binary mode
bye
Disconnect with the remote FTP Server and return to user
view
cd
Change the working path on the remote FTP server
cdup
change working path on the FTP server to the next level up in
the directory structure
close
Terminate the control connection and data connection with
the FTP Server and remain in FTP client view
debugging
Enable the system debugging functions
delete
Delete a file on the FTP server
dir
Query a file or display the contents of current working
directory
disconnect
Disconnect FTP client side from FTP server side without exiting
FTP client view
get
Download a remote file and save it locally
lcd
View local working path of FTP client
ls
Query a file or display the contents of current working
directory
mkdir
Create a directory on the FTP server
open
Open FTP connection
passive
Configure the data transmission mode as passive mode
(passive mode is the default data transmission mode)
put
Upload a local file to the FTP server
pwd
View the current directory on the FTP server
quit
Terminate the connection with the FTP server and return to
user view
remotehelp
View help text about FTP commands
rmdir
Delete a specified directory from the FTP server
user
Register an FTP user
verbose
Enable verbose (verbose is enabled by default)
Command
Description
Web Command
accounting optional
Enable the selection of RADIUS accounting option
data-flow-format
Configure the unit of data flow that send to RADIUS Server
key
Configure encryption key for RADIUS authentication/
authorization or accounting packet
Security -> RADIUS Client
nas-ip
Set the source IP address of the network access server (NAS,
i.e: the Switch), so that all packets destined for the RADIUS
server carry the same source IP address
primary accounting
Configure the IP address and port number for the primary
accounting server
primary authentication
Configure the IP address and port number for the primary
RADIUS authentication/authorization
retry
Configure retransmission times of RADIUS request packet
retry realtime-accounting
Configure the maximum times of real-time accounting
request failing to be responded
14
Table 12
ISP Domain View
[4500]
domain test
Table 13
VLAN View
[4500]
vlan 2
Table 14
VLAN Inteface View
[4500]
interface vlan 2
retry stop-accounting
Configure the maximal retransmission times after stopping
accounting request
secondary accounting
Configure the IP address and port number for the second
RADIUS accounting server
secondary authentication
Configure the IP address and port number for the second
RADIUS authentication/authorization
Security -> RADIUS Client
server-type
Configure the supported RADIUS server types
state
Configure the state of RADIUS server
stop-accounting-buffer
enable
Configure to save the stopping accounting requests without
response in the Switch system buffer
timer
Configure RADIUS server response timer
timer quiet
Specify the wait time for re-activating primary server
timer realtime-accounting
Configure the real-time accounting interval
timer response-timeout
Configure the RADIUS server response timer
user-name-format
Configure the username format sent to RADIUS server
Command
Description
Web Command
access-limit
Configure a limit to the amount of supplicants in the current
ISP domain
accounting optional
Enable the selection of RADIUS accounting option
idle-cut
Configure the user template in the current ISP domain
messenger
Specify messenger service of domain
radius-scheme
Configure the RADIUS server group used by the current ISP
domain
scheme
Configure the AAA scheme to be referenced by the current
ISP domain
self-service-url
Specify self-service URL (Uniform Resource Locator) of domain
state
Configure the state of the current ISP domain
Command
Description
Web Command
description
Configure a description for the current VLAN or VLAN
interface
Device -> VLAN
igmp-snooping
IGMP snooping
port
Add ports to or delete ports from VLAN
Device -> VLAN
Command
Description
Web Command
description
Configure a description for the current VLAN or VLAN
interface
dhcp-server
Configure corresponding DHCP Server Group of a VLAN
Interface
enable snmp trap
Enable SNMP traps on an interface
ip address
Configure an IP address for VLAN interface
Administration -> IP Setup
-> Device -> VLAN Interface
Command
Description
Web Command
15
Table 15
Ethernet Port View
[4500]
interface ethernet 1/0/1
ip address dhcp-alloc
Configure a VLAN interface to obtain IP address using DHCP
Administration -> IP Setup
-> Device -> VLAN Interface
rip authentication-mode
Configure RIP-2 authentication mode and its parameters
rip input
Allow an interface to receive RIP packets
rip metricin
Configure the additional route metric added to the route
when an interface receives RIP packets
rip metricout
Configure the additional route metric to the route when an
interface transmits RIP packets
rip output
Allow an interface to transmit RIP packets to the network
rip split-horizon
Configure an interface to use split horizon when transmitting
RIP packets
rip version
Configure the RIP version of RIP packets on an interface
rip work
Enable the running of RIP on an interface
shutdown
Disable the VLAN interface
Device -> VLAN Interface
udp-helper server
Configure the relay destination server
Command
Description
Web Command
am ip-pool
Configure the IP address pool for access management on a
port
arp static
Configure the static ARP mapping entries in an ARP mapping
table
broadcast-suppression
Configure the broadcast traffic size enabled on port
Port -> Administration
description
Configure name for a port
dot1x max-user
Specify maximal on-line user number per port
dot1x port-control
Specify port authenticated status
dot1x port-method
Specify port controlled method
dot1x supp-proxy-check
Check whether user(s) access the networks by proxy or not
duplex
Configure the duplex mode of the port
Port -> Administration
enable snmp trap
Enable/disable current port to transmit the LINK UP and LINK
DOWN trap information
flow-control
Enable flow control on the Ethernet port
Port -> Administration
lacp enable
Enable LACP
Port -> LACP
lacp port-priority
Configure port priority value
Port -> LACP
line-rate
Limit the total rate of the packets delivered by interfaces
loopback
Configure the Ethernet port to perform the loopback test
Tools -> Loopback
loopback-detection
control enable
Enable loopback detection control function on a trunk or
hybrid port
loopback-detection enable
Enable port loopback detection
loopback-detection per-
vlan enable
Configure loopback detection on all VLANs on trunk and
hybrid ports
mac-address blackhole
Backhole entry, no age, can be added or deleted, and is saved
to the configuration file
mac-address dynamic
Dynamic entry, age, can be added or deleted, and is lost after
reset
mac-address max-mac-count
Limit the number of MAC addresses to be learned by an
Ethernet port
Port -> Administration
mac-address static
Static entry, no age can be added or deleted, and is saved to
the configuration file
mac-authentication
Enable the centralized MAC address authentication feature on
a specified port or globally
Command
Description
Web Command
16
Table 16
Route Policy View
[4500]
route-policy policy 1 permit node 1
Specify name, action and node to see the options below
mdi
Configure the network cable type of the Ethernet ports
Port -> Administration
mirrored-to
Enable ACL traffic identification and perform traffic mirror
mirroring-port
Configure a monitored port
Port -> Mirroring
monitor-port
Configure a monitor port
Port -> Mirroring
multicast-suppression
Configure the multicast traffic size enabled on port
packet-filter
Activate ACL
poe enable*
Enable PoE
poe max-power*
Maximum Power
Device -> PoE
poe mode*
Port Mode
poe priority*
Port Priority
port access vlan
Join the access port to a specified VLAN
Port -> Administration
port hybrid pvid vlan
Configure the default VLAN ID of the hybrid port
Port -> Administration
port hybrid vlan
Join the hybrid port to specified existing VLAN
Port -> Administration
port isolate
Add a port to an isolation group
Port -> Administration
port link-aggregation
group
Add an Ethernet port into a manual or static aggregation
group
port link-type
Configure the link type of Ethernet port
Port -> Administration
port trunk permit vlan
Join trunk port to specified VLAN
port trunk pvid vlan
Configure the default VLAN ID of trunk port
priority
Configure the priority of Ethernet port
priority trust
Configure system trusting the packet 802.1p priority and not
replacing the 802.1p priorities carried by the packets with the
port priority
rmon history
Add an entry to the history control table
rmon statistics
Add an entry to the statistic table
shutdown
Disable the port
Port -> Administration
speed
Configure the port speed
Port -> Administration
stp
Enable Spanning Tree Protocol
Port -> Spanning Tree Per Port
stp cost
Configure the path cost on a spanning tree for the current
Ethernet port
Port -> Spanning Tree Per Port
stp disable
Disable spanning tree protocol on the port
stp edged-port
Configure the current port as an edge port
Port -> Spanning Tree Per Port
stp loop-protection
Enable loop protection function
Port -> Spanning Tree Per Port
stp mcheck
Force the port to work in RSTP mode
Port -> Spanning Tree Per Port
stp point-to-point
Configure the link to the current port as point-to-point link or
not point-to-point link
Port -> Spanning Tree Per Port
stp port priority
Configure the priority of the current Ethernet port
Port -> Spanning Tree Per Port
stp root-protection
Enable Root protection
Port -> Spanning Tree Per Port
stp transmit-limit
Set the maximum number of STP packets the current port can
send within one Hello time
Port -> Spanning Tree Per Port
unicast-suppression
Configure the limit to unknown unicast flooding
voice vlan enable
Enable the Voice VLAN features on the port
wred
Configure WRED parameters
Command
Description
Web Command
apply cost
Configure the route cost value of route information
apply tag
Set a tag field of the matched route
Command
Description
Web Command
17
Table 17
RIP View
[4500]
rip
Table 18
ACL View
[4500]
acl number xxxx
(where
xxxx
is the acl number)
if-match acl
Configure the IP address range to match the acl
if-match IP
Configure the IP address range to match the IP
if-match IP-prefix
Configure the IP address range to match the IP prefix
if-match tag
Configure the IP address range to match the tag
if-match cost
Configure one of the match rules of route-policy to match
the cost of the routing information
if-match interface
Set to match route whose next hop is designated interface
if-match ip next-hop
Configure one of the match rules of route-policy on the next
hop address of the routing information
Command
Description
Web Command
checkzero
Perform the checkzero operation in the zero field of RIP-1
default cost
default routing cost of an imported route
host-route
Enable receiving host-routes
filter-policy
Spcify a route filtering policy
import-route
Import routes from other protocols into RIP
network
Enable routing protocol on the related network or interface
peer
Specify a peer route
preference
Specify an RIP route preference
reset
Reset RIP configuration
summary
Enable RIP-2 automatic route summarization
timers
Config RIP timers
Command
Description
Web Command
description
Specify the ACL description
rule
Add a subrule to an ACL
Device -> ACL
Security -> Authorized IP
Command
Description
Web Command
Copyright © 2007, 3Com Corporation. All rights reserved.
www.3Com.com
Part Number: 10015872 Rev. AA
Published: January, 2007