Full Text Searchable PDF User Manual

INSTALLATION MANUAL
2Easy 1 User Video Entry Kit

2
Easy 1 User Video Entry Kit
2

Camera Lens
Night View LED
Speaker
Nameplate
Call Button
Microphone
90 mm
176 mm
23 mm
BUS PL
S1+ S2+
S-
1
2
ON
1
2
ON
MIC adjustment
Lock Control Jumper
Doorstation Code DIP
Main Connect Port
1 2 3
SPK adjustment
Rain Cover
2
Easy 1 User Video Entry Kit
CDV4791/2
2.
1:
Terminal Descriptions
2
:
CDV91/92
Parts and Functions
3

160-165cm
1
2
1
2
3
4
2.2: Installation & Adjustments
Mounting Without Rain Cover
2
Easy 1 User Video Entry Kit
CDV4791/2
160-165cm
1
2
1
2
3
4
Mounting With Rain Cover
4

name label
1
2
ON
4.3
Fitting The
Name Label
From the rear of the metal section of the CDV91/92 unclip
the plastic to open the transparent name
plate
, insert a name
label and replace the
plastic
cover.
4.4 Adjusting Camera Angle
Use a screwdriver to loosen the screw and adjust
the
angle of the camera
retighten the screw to fix
the angle.
2
Easy 1 User Video Entry Kit
CDV4791/2
5

2
Easy 1 User Video Entry Kit
CDV4791/2
The PC6A is a power/bus combiner unit, which is designed for the CDV 2Easy 2 wire
system to supply power for the external station, internal monitor and other accessories on
the bus. It can operate as a normal power/bus combiner or auxiliary PSU.
The features are
as follows:
• Universal AC input/full range
• Multi protection: short circuit, overload, over voltage
• Integrated with DT-DPS(power separator), Additional
DT-DPS is not needed.
• Support up to 4~8 monitors(depend on models)
• DIN Rail Mounting
LED
CN
1 2 3
BUS(IM) BUS(DS)
N
L
PG
L
100~240 Vac
PG
N
L
L
PG:
Earth ground terminal.
N:
AC input terminal.
L:
AC input terminal.
LED:
Power indicator, on when power connected.
CN:
Bus control terminal.
BUS(IM):
Indoor monitor connection terminal.
BUS(DS):
Door station connection terminal.
3.1:
Description:
3:
CDV
-PC6A
Parts and Functions
3.
2: Terminal Descriptions:
6

2
Easy 1 User Video Entry Kit
CDV4791/2
Open the AC cover:
1. Push the cover base towards
the centre with your fingers;
2. Lift up and pull out the cover.
After connecting the AC cable, it is
advised to replace the cover.
Note:
1. The AC cable is not included in the
package, it must comply to the specific
requirements of country where installed.
CN
1 2 3
BUS(IM)
Connect to monitor
Connect to door staiton
BUS(DS)
AC Input
100~240Vac
N L
PG
L
*
Digital TFT LCD Screen
UNLOCK Button
TALK/MON Button
Microphone
Connection Port
Speaker
Mounting Hook
Mounting Hook
1 2 3
ON
DIPS
L1
L2
Emergency Button
Message Indicator
4:
CDV47
Parts and Functions
2. Pins 1&2 should be short-circuited
with a C3-3P link(included in the package)
if the unit operates as a standard power
combiner. If operating as an auxiliary
power combiner, the link should be
removed.
7

1 2
3
ON
Bit
DIP1&2
Reserved. left to default.
Set to OFF. When the monitor is in the middle of the line in daisy chain connection.
Bit State
Description
DIP3
1 2
3
ON
1 2
3
ON
Press to display the camera view
when
in standby mode
Microphone
Transmit
s
voice communication
Mounting hook
To secure monitor to
wall
bracket
Connection port
Bus connection. DiP switches and door bell input.
Speaker
Receive
s
voice communication
145~160 cm
LCD screen
Display
s
the
camera
image
Emergency button Press for 3 seconds to send an SOS message
*
Message indicator Indicates a new visitor call record
ing
Unlock button
Press to release the door
Talk/Mon button
Press to communicate with the visitor when called
2
Easy 1 User Video Entry Kit
CDV4791/2
Key functions:
DIP Settings
:
8
Set to ON. When the montior is at the end of the line.

1.Touch
icon on
main menu page.
2.Touch
UNLOCK
button and hold for 2s.
3.A digital keypad
will be shown.
About
Local Address
00.00
Video Standard
AUTO
System Verson
00.01.00
Display Driver
1.0
Front
1.0
UI
1.0
INSTALLER SETUP
123
_
Touch the screen anywhere on monitor
in standby mode, the main menu page
will be shown as follows:
A maximum of 4 monitors can be connected in one apartment (call button), one
master monitor together with 3 slave monitors, the address must be set
correctly.(Note: one monitor to be set as master monitor - address 00)
The code of 8000 is used to set the master monitor.
The code of 8001 is used to set the first slave monitor .
The code of 8002 is used to set the second slave monitor .
The code of 8003 is used to set the third slave monitor .
How to enter the installation setting page:
Setting the Slave address:
2
Easy 1 User Video Entry Kit
CDV4791/2
9

In default mode, when receive a calling the master and slave monitors will ring at the
same time, however the master monitor will display the image while the slave monitors
will not. This setting can be changed to allow all the slave monitors to display video from
the panel at the same time when receiving a call, enter the code number of 8006 on
each slave monitor. (Note: it is not recommended to have more than 2 monitors se to on
when using cat5/6 cable).
The system offers two methods of date and time.
Code number of 8008 is used to set the date format as month/day/year.
Code number of 8009 is used to set the date format as day/month/year.
Code number of 8012 is used to set the time format as 12 hour system.
Code number of 8013 is used to set the time format as 24 hour system.
There are two unlock modes:
1.power-on- to-unlock type:unlock mode =0 (by default)
2.power-off-to-unlock:unlock mode = 1.
Code number of 8010 is used to set the unlock mode to 0
Code number of 8011 is used to set the unlock mode to 1
Unlock time:
The unlock time can be changed by yourself at any time.it can be set from 1 to 99 seconds.
The code number from 8401 to 8499 are used to set the unlock time to 1~ 99 seconds.
Setting
the slave monitor video on:
How to set date and time format
:
How to set the unlock parameter
:
Unlock mode:
2
Easy 1 User Video Entry Kit
CDV4791/2
10

Input No.
User Code
Input No.
User Code
Input No.
User Code
8201
Code=1
8212
Code=12
8223
Code=23
8202
Code=2
8213
Code=13
8224
Code=24
8203
Code=3
8213
Code=14
8225
Code=25
8204
Code=4
8215
Code=15
8226
Code=26
8205
Code=5
8216
Code=16
8227
Code=27
8206
Code=6
8217
Code=17
8228
Code=28
8207
Code=7
8218
Code=18
8229
Code=29
8208
Code=8
8219
Code=19
8230
Code=30
8209
Code=9
8220
Code=20
8231
Code=31
8210
Code=10
8221
Code=21
8232
Code=32
8211
Code=11
8222
Code=22
Setting the user code (address) for the monitor:
2
Easy 1 User Video Entry Kit
CDV4791/2
Input No.
User Code
Input No.
User Code
Input No.
User Code
8201
Code=1
8212
Code=12
8223
Code=23
8202
Code=2
8213
Code=13
8224
Code=24
8203
Code=3
8213
Code=14
8225
Code=25
8204
Code=4
8215
Code=15
8226
Code=26
8205
Code=5
8216
Code=16
8227
Code=27
8206
Code=6
8217
Code=17
8228
Code=28
8207
Code=7
8218
Code=18
8229
Code=29
8208
Code=8
8219
Code=19
8230
Code=30
8209
Code=9
8220
Code=20
8231
Code=31
8210
Code=10
8221
Code=21
8232
Code=32
8211
Code=11
8222
Code=22

B
A
C
DPS
PS5
DBC4
monitor
monitor
monitor
with two
to
four monitors
F
a
rthest
monitor
The maximum cable distance of the wiring is limited. Using different cables will also affect
the maximum distance available from the 2Easy system.
5: Schematics & Wiring
2
Easy 1 User Video Entry Kit
CDV4791/2
12
Cable Usage
A
B
C
Twisted cable 2x1 mm
2
80
80
40
Cable Usage
A
B
C
Twisted cable 2x1 mm
2
70
30
20
Twisted cable 2x1.5 mm
2
70
50
30
Monitor quantity < 20
Twisted cable 2x0.75 mm
2
60
60
30
Monitor quantity > 20

1
2
5.
2
Basic
Wiring Configurations
-
+
monitor
ON
L1 L2 PL S1+ S2+ S-
monitor
monitor
monitor
monitor
1 2
ON
ID=00
'Daisy Cha
i
n Connection:
2
Easy 1 User Video Entry Kit
CDV4791/2
13

OFF ON
monitor
monitor
monitor
monitor
ID=00
1 2
ON
A B C D
Impedance
switch
DIP=on,off,off
85~260VAC
DPS
PS5
monitors
L1 L2 PL S1+ S2+ S-
L1 L2 PL S1+ S2+ S-
L1 L2 PL S1+ S2+ S-
L1 L2 PL S1+ S2+ S-
1 2
ON
1 2
ON
1 2
ON
1 2
ON
1# Camera
DIP=on,off,off
ID=11
ID=01
ID=10
ID=00
4# Camera
3# Camera
2# Camera
DBC4
A B C D
OFF
ON
Impedance
switch
Star Connection with CDV-DBC4A:
Multiple Door Station Connection
2
Easy 1 User Video Entry Kit
CDV4791/2
14
DBC4
A

EB
*
LOCK
BUS
PL
S1+
S2+
S-
LOCK
2
nd
1
ST
2
nd
EB
*
1
ST
EB
*
LOCK
BUS
PL
S1
+
S2
+
S-
Note:
C
onnect
ing
one lock
: C
onnect
ing
two locks
:
Jumper position in
1 & 2
Jumper position in
1 & 2
1. Electric locks must be Power-on-to-unlock.
2. The door lock output is limited to 12V with holding current maximum of 250mA.
3. The door lock output is not timed from the Exit Button(EB).
4. The unlock parameter of the monitor must be set to 0 (default).
5.3 Electric Lock Connection
2
Easy 1 User Video Entry Kit
CDV4791/2
15

LOCK
BUS
PL
S1
+
S2
+
S-
Take off the Jumper
POWER
SUPPLY
LOCK
BUS
PL
S1
+
S2
+
S-
Take off the Jumper
POWER
SUPPLY
LOCK
Note
:
1. The external power supply must be rated according to the lock consumption.
2. The jumper must be removed before connecting.
3. Set up the unlock mode for the monitor for lock type:
C
onnect
ing
one lock
C
onnect
ing
two locks
8010 - Power-on-to-unlock type:Unlock Mode=0 (default)
8011 - Power-off-to-unlock type:Unlock Mode=1
2
Easy 1 User Video Entry Kit
CDV4791/2
Temperature:
Power Supply :
DC 24V (supplied by PS1-24V or PS5-24V)
Power Consumption:
Standby 50mA;
Operating Current:
200mA
Camera:
Pinhole Sharp Color CCD; 420 TV Lines
Unlocking time:
1-9S, set by monitorLock
Power supply:
12Vdc, 300mA(Internal Power)
-10
0
C~+45
0
C
Wiring:
2 wires - Unscreened twistedpair(non-polarity)
Dimension:
176(H)×90(W)×24(D)mm
16

2
Easy 1 User Video Entry Kit
CDV4791/2
Input Voltage
:
100~240Vac
Input Frequency:
50~60HzRated
Output Voltage:
DC 28V+2V
Rated Output Current:
1.5A
Working Temperature:
-10
0
C~50
0
CSW
Input Voltage:
Max 230vac, 2A
Dimension:
140 x 90 x 60mm
17
1) All components should be protected from shock or vibration, and be careful the
products are not impacted, knocked or dropped.
2) Please clean with a soft cotton cloth, please do not use a chemical cleaning agent. If
necessary, please use a little pure water or dilute soapy water to clean.
3) Image distortion may occur if the video monitor is mounted too close to a magnetic
feld eg microwaves, TV's, computers etc.
4) Please do not subject the monitor to wet, high temperature, dust, caustic and oxidation
gas environments, any of which could cause unpredictable damage.
5) Please use the right adaptor which is supplied by the manufacturer, or approved
by the manufacturer.
6) Pay attention to the
high voltage
inside the products, please refer service only to a
trained and qualifed professional.

2
Easy 1 User Video Entry Kit
CDV4791/2
1) All components should be protected from shock or vibration, prevent impacts and
sharp knocks. Do not drop
2) Please clean with a soft cotton cloth, please do not use a chemical cleaning agent. If
necessary, please use a little pure water or dilute soapy water to clean.
3) Image distortion may occur if the video monitor is mounted too close to a magnetic
feld eg microwaves, TV's, computers etc.
4) Please do not subject the monitor to wet, high temperature, dust, caustic and oxidation
gas environments, any of which could cause unpredictable damage.
5) Please use the right adaptor which is supplied by the manufacturer, or approved
by the manufacturer.
6) Pay attention to the
high voltage
inside the products, please refer service only to a
trained and qualifed professional.
18