1byone Easy Chime OUKQH-0536 Instruction Manual - User Manual

Full Text Searchable PDF User Manual

Instruction Manual

SKU: OUKQH-0536

1byone Products Inc.
1230 E Belmont Street, Ontario, CA 91761
Customer Service: +1 909-391-3888
www.1byone.com

All products with the Easy Chime logo can work together

Thank you for purchasing this 1byone Wireless
Doorbell. Please read this instruction manual
before use to ensure safe operation.

1. Package Contents:

2 x Doorbell receivers (1 x battery-operated

receiver and 1 x Plug-in receiver)

1 x Push button
1 x 3V Battery for push button (Type: CR2032)
1 x Double-sided adhesive
3 x Wall plugs and 3 x Screws
1 x Instruction manual

If any package contents are visibly damaged or
missing, please immediately contact 1byone
Support Center at https://www.1byone.com/Sup-
port for assistance.

2. Parts Names:

- 01 -

- 02 -

1. LED indicator

2. Speaker

3. Sound and flash switch

4. Volume button

5. Ringtone selector button

6. Pairing button

7. Plug

Receiver front side

Receiver back side

(1)

(2)

(3)

(5)

(6)

(4)

(7)

Push button

Transparent cover

Name plate

B. Selecting the ringtone:

There are 36 programmable ringtones for
selection.
Press the Ringtone selector button to
change the ringtone.
Stop pressing this button when you have
reached the desired ringtone.

C. Adjusting ringtone volume:

Press the volume button until the desired
volume is set. There are 3 volume levels for
selection.

D. Pairing additional push buttons/receivers to the

doorbell system:
Up to 5 push buttons can be paired with one
receiver. You can also extend the wireless
doorbell system with any number of receivers.
This is only possible if the push button and
receiver are working on the same frequency.
Pair additional push buttons/receivers using the
same pairing process as described below:
The following pairing instructions are relevant

Always insert the battery using the correct
polarity to eliminate the danger of fire.

Keep old and new batteries away from children.

Old batteries should be properly disposed using
safe environmental practices.

Remove the batteries from the receiver and
push button if the doorbell system is not to be
used for an extended period of time.

4. Operation:

A. Selecting the notification mode:

The doorbell receiver can notify after the push
button has been pressed by playing a ringing
sound, flashing an LED, or ringing and flashing
an LED at the same time. These are referred to as
Sound, Flash, and Sound + Flash mode.
To select the notification mode, switch the
sound and flash switch to one of the following
positions:

Sound only mode Flash only mode

Sound + Flash mode

3. Power supply:

Battery-operated receiver: The receiver is powered
by 2 x AA batteries. Please insert the batteries
using the following procedure:
a) Press the buckle on the battery compartment

cover and remove the battery compartment
cover at the back of the receiver.

b) Insert the 2 x AA batteries using the correct

polarity to eliminate the danger of fire.

c) Reattach the battery compartment cover.

Plug in receiver: Please plug into a safety power
outlet.

Push button: The push button is powered by a 3V
battery (Type: CR2032). Please insert the battery
using the following procedure:
a) Insert a screwdriver into the small access port at

the bottom of the push button and remove the
push button’s back cover.

b) Insert the 3V battery (type CR2032) into the

battery compartment, making sure the battery
surface marked with a “+” is facing upwards.

c) Reinsert the back cover, making sure it is

securely closed to ensure IP protection.

Note:
If the performance of the push button deteriorates
or completely stops, the battery might be
exhausted. Please replace with another 3V type
CR2032 battery.

Weak batteries can greatly reduce the ringtone
volume of the receiver, please change the
batteries every 8-10 months.

Safety note:
For the plug-in receiver:

Please plug it into a safe power outlet

Do not expose the receiver to water spray or
water drops and do not place liquid-filled
objects such as vases or opened drink
containers on or near the receiver and the
outlet.

Unplug the receiver immediately if you sense a
burning smell or smoke. Have qualified
personnel check the receiver before using it
again.

Unplug the receiver from the outlet if the
doorbell system is not to be used for an
extended period of time.

For the battery-operated receiver and push button:

Weak battery can greatly reduce the ringtone of
the receiver, please replace with the same
voltage and type batteries every 8-10 months.

- 03 -

- 04 -

Parameters:

1. Speaker

2. LED indicator

3.Wall mounting hole

4. Volume button

5. Sound and flash switch
6. Ringtone selector button
7. Pairing button

Voltage of
battery-operated receiver
Voltage of plug-in receiver
Voltage of push button
Frequency
Operating range
Power consumption:
Receiver’s ring volume
Working temperature

DC 3V (2 x AA batteries)

AC 220-240V
DC 3V (CR2032 battery)
433.92MHz+100KHz
100m/300ft (without obstacles)
Receiver:

＜

0.3W Push button:

＜

10mA

Over 85dB within 0.5m/1.64ft
-20

℃

-50

℃

to receiver (SKU: O00QH-0504) and push button
(SKU: O00QH-0503).
Press the pairing button on the receiver.
Next press the push button. If pairing is
successful, the receiver should ring. It normally
takes about 10 seconds for the push button and
receiver to pair. If there is no pairing within 10
seconds, the receiver will exit the pairing mode.
Please try pairing again.

E. Re-pairing function:

If a receiver starts ringing even when the push
button hasn’t been pressed, or a push button
interferes with other receivers, it may be
necessary to wipe the current pairings and pair
again.
To reset the push buttons, you need to cut off
the power supply for the receiver and push
button.
Remove the battery from the push button and
unplug the receiver from the power outlet. Then
re-attach them to power after 30 seconds. You
can now pair the desired push buttons.

B. Selecting the ringtone:

There are 36 programmable ringtones for
selection.
Press the Ringtone selector button to
change the ringtone.
Stop pressing this button when you have
reached the desired ringtone.

C. Adjusting ringtone volume:

Press the volume button until the desired
volume is set. There are 3 volume levels for
selection.

D. Pairing additional push buttons/receivers to the

Always insert the battery using the correct
polarity to eliminate the danger of fire.

Keep old and new batteries away from children.

Old batteries should be properly disposed using
safe environmental practices.

Remove the batteries from the receiver and
push button if the doorbell system is not to be
used for an extended period of time.

4. Operation:

A. Selecting the notification mode:

Sound only mode Flash only mode

Sound + Flash mode

3. Power supply:

Battery-operated receiver: The receiver is powered
by 2 x AA batteries. Please insert the batteries
using the following procedure:
a) Press the buckle on the battery compartment

cover and remove the battery compartment
cover at the back of the receiver.

b) Insert the 2 x AA batteries using the correct

polarity to eliminate the danger of fire.

c) Reattach the battery compartment cover.

Plug in receiver: Please plug into a safety power
outlet.

Push button: The push button is powered by a 3V
battery (Type: CR2032). Please insert the battery
using the following procedure:
a) Insert a screwdriver into the small access port at

the bottom of the push button and remove the
push button’s back cover.

b) Insert the 3V battery (type CR2032) into the

battery compartment, making sure the battery
surface marked with a “+” is facing upwards.

c) Reinsert the back cover, making sure it is

securely closed to ensure IP protection.

Note:
If the performance of the push button deteriorates
or completely stops, the battery might be
exhausted. Please replace with another 3V type
CR2032 battery.

Weak batteries can greatly reduce the ringtone
volume of the receiver, please change the
batteries every 8-10 months.

Safety note:
For the plug-in receiver:

Please plug it into a safe power outlet

Do not expose the receiver to water spray or
water drops and do not place liquid-filled
objects such as vases or opened drink
containers on or near the receiver and the
outlet.

Unplug the receiver immediately if you sense a
burning smell or smoke. Have qualified
personnel check the receiver before using it
again.

Unplug the receiver from the outlet if the
doorbell system is not to be used for an
extended period of time.

For the battery-operated receiver and push button:

Weak battery can greatly reduce the ringtone of
the receiver, please replace with the same
voltage and type batteries every 8-10 months.

- 05 -

- 06 -

E. Re-pairing function:

B. Selecting the ringtone:

There are 36 programmable ringtones for
selection.
Press the Ringtone selector button to
change the ringtone.
Stop pressing this button when you have
reached the desired ringtone.

C. Adjusting ringtone volume:

Press the volume button until the desired
volume is set. There are 3 volume levels for
selection.

D. Pairing additional push buttons/receivers to the

Always insert the battery using the correct
polarity to eliminate the danger of fire.

Keep old and new batteries away from children.

Old batteries should be properly disposed using
safe environmental practices.

Remove the batteries from the receiver and
push button if the doorbell system is not to be
used for an extended period of time.

4. Operation:

A. Selecting the notification mode:

Sound only mode Flash only mode

Sound + Flash mode

3. Power supply:

Battery-operated receiver: The receiver is powered
by 2 x AA batteries. Please insert the batteries
using the following procedure:
a) Press the buckle on the battery compartment

cover and remove the battery compartment
cover at the back of the receiver.

b) Insert the 2 x AA batteries using the correct

polarity to eliminate the danger of fire.

c) Reattach the battery compartment cover.

Plug in receiver: Please plug into a safety power
outlet.

Push button: The push button is powered by a 3V
battery (Type: CR2032). Please insert the battery
using the following procedure:
a) Insert a screwdriver into the small access port at

the bottom of the push button and remove the
push button’s back cover.

b) Insert the 3V battery (type CR2032) into the

battery compartment, making sure the battery
surface marked with a “+” is facing upwards.

c) Reinsert the back cover, making sure it is

securely closed to ensure IP protection.

Note:
If the performance of the push button deteriorates
or completely stops, the battery might be
exhausted. Please replace with another 3V type
CR2032 battery.

Weak batteries can greatly reduce the ringtone
volume of the receiver, please change the
batteries every 8-10 months.

Safety note:
For the plug-in receiver:

Please plug it into a safe power outlet

Do not expose the receiver to water spray or
water drops and do not place liquid-filled
objects such as vases or opened drink
containers on or near the receiver and the
outlet.

Unplug the receiver immediately if you sense a
burning smell or smoke. Have qualified
personnel check the receiver before using it
again.

Unplug the receiver from the outlet if the
doorbell system is not to be used for an
extended period of time.

For the battery-operated receiver and push button:

Weak battery can greatly reduce the ringtone of
the receiver, please replace with the same
voltage and type batteries every 8-10 months.

- 07 -

- 08 -

VOL

1/2/3

E. Re-pairing function:

- 09 -

- 10 -

5. Installation:

Plug-in receiver: Plug it into a safety power
outlet.
Battery-operated receiver: The receiver can be
mounted on a wall or just put on a flat surface.

To be mounted on a wall:
Select a suitable location for the doorbell,
usually close to your outside door.
Drill holes on the wall. Next push the wall plug
into the drilled holes and then insert the screw
into the wall plugs. Finally, mount the receiver
with screw.

Push button: Install the push button by
double-sided adhesive or by screws:

a. By double-sided adhesive:

Select a suitable location for the push button,
usually close to your outside door.
Stick the push button to the wall using the
included double-sided adhesive.

b. By screws:

Select a suitable location for the doorbell,
usually close to your outside door.

Pierce the two pre-stamped grooves (A) on the
inner side of the back cover with a pointed
object. Drill holes on the wall. Next push the wall
plugs into the drilled holes and screw the back
cover onto the wall with screws.

Push the front cover onto the back cover and
make sure it is securely closed to ensure IP
protection.

Notes:

The push button and receiver can connect with
a range up to 100m/300ft without any
obstacles.

The push button’s transmitting frequency is
433MHz and its range can be affected by metal
,walls, concretes, and interfering signals from
other electronic appliances with the same
frequency including televisions, radios, and
cookers.

Please do not install the push button and
receiver near to the above mentioned
electronic appliances.

Please test the operating range of the receiver
and push button in your home before
installation.

Do not install the push button and receiver near
any source of naked flames such as lighted
candles.

Do not expose the push button and receiver to
direct sunlight or high temperatures, otherwise
overheating may cause them irreparably
damaged.

- 11 -

- 12 -

c. Install the name plate:

Remove the transparent cover from the push
button.
Then write your name or room number on a
small paper (size: 2.3cm/0.9in x 2.0cm/0.8in).
Next, put the small paper into the transparent
cover and then put back the transparent cover
on the push button.

Note:
If you make the name plate by hand, be sure to
use a waterproof pen.

6. Trouble Shooting:

a. The receiver rings without the push button

being pressed.
The receiver may be matched on the same
frequency with nearby push buttons. You should
wipe the pairing and re-pair your push button(s).

b. There is no ring/LED flash when the push

button is pressed.

Check whether the battery (CR2032) is inserted
into the push button.

For the plug-in receiver,check whether the
power supply for the receiver is working
properly.

Pair the receiver and push button again.

For the battery-operated receiver,check
whether the batteries are inserted into the
receiver.

c. The ringtone volume is greatly reduced.
A weak battery can reduce the ringtone volume

of the receiver. Please change the battery every
10-12 months.

Metal constructions, walls, and other appliances

with the same frequency can also affect the
receiver’s ringing effect. Avoid mounting the
push button and receiver near any metal objects.

Disposal of the appliance

Under no circumstances should you
dispose of the appliance with normal
domestic waste. This product is subject
to the provisions of European Directive
2012/19/EU.

Dispose of the appliance via an approved disposal
company or your municipal waste facility. Please
observe the currently applicable regulations.
Please contact your waste disposal centre if you
need any further information.

Disposal

Disposal of batteries

Used batteries may not be disposed of
with household waste.

All consumers are statutorily required to dispose
of batteries at a collection point provided by
their local municipality or retail store.
The purpose of this obligation is to ensure

Notes:

The push button and receiver can connect with
a range up to 100m/300ft without any
obstacles.

Please do not install the push button and
receiver near to the above mentioned
electronic appliances.

Please test the operating range of the receiver
and push button in your home before
installation.

Do not install the push button and receiver near
any source of naked flames such as lighted
candles.

Do not expose the push button and receiver to
direct sunlight or high temperatures, otherwise
overheating may cause them irreparably
damaged.

- 13 -

- 14 -

c. Install the name plate:

Note:
If you make the name plate by hand, be sure to
use a waterproof pen.

6. Trouble Shooting:

a. The receiver rings without the push button

being pressed.
The receiver may be matched on the same
frequency with nearby push buttons. You should
wipe the pairing and re-pair your push button(s).

b. There is no ring/LED flash when the push

button is pressed.

Check whether the battery (CR2032) is inserted
into the push button.

For the plug-in receiver,check whether the
power supply for the receiver is working
properly.

Pair the receiver and push button again.

For the battery-operated receiver,check
whether the batteries are inserted into the
receiver.

c. The ringtone volume is greatly reduced.
A weak battery can reduce the ringtone volume

of the receiver. Please change the battery every
10-12 months.

Metal constructions, walls, and other appliances

with the same frequency can also affect the
receiver’s ringing effect. Avoid mounting the
push button and receiver near any metal objects.

The appliance’s packaging is made
from environmentally friendly material
and can be disposed of at your local
recycling plant.

Declaration of Conformity

We, the 1byone Products Inc. confirm that the appliance
as detailed below do comply with all essential
requirements of the EMC directive 2014/53/EU and
governing EU-regulations as mentioned below.

Article Description: Wireless Doorbell
Brand Name: 1byone
Model Number: OUKQH-0536
Governing EU-regulations: RoHS Directive 2011/65/EU

WEEE 2012/19/EU

Applicable Standard(s):
EN 301 489-1 V2.2.0
EN 301 489-3 V2.1.1
EN 300 220-2 V3.1.1
EN 62479:2010
EN 60065:2014

Ray Tang

Department Manager

batteries are disposed of in a non-polluting
manner. Only dispose of batteries when they are
fully discharged.

- 15 -

US
To ensure speedy handling of your issue, please call
or email us for assistance.
Phone: +1 909-391-3888
(Mon-Fri 9:00am - 6:00pm PST)
Email: ushelp@1byone.com

UK
To ensure speedy handling of your issue, please call
or email us for assistance.
Phone: +44 158 241 2681
(Mon-Fri 9:00am - 6:00pm UTC)
Email: ukwebhelp@1byone.com

FR
Pour vous assurez une assistance rapide en cas de
problème, veuillez envoyer un e-mail.
Email: euhelp@1byone.com

Customer Service/Kundenservice

Service Clients/Atención al cliente

Assistenza Clienti/

カスタマーサービス

IT
Per supporto immediato in caso di bisogno, la
invitiamo a contattarci via email.
Email: euhelp@1byone.com

CA
To ensure speedy handling of your issue, please
email us for assistance.
Email: cahelp@1byone.com

DE
Für eine zügige Bearbeitung ihres Problems, melden
Sie sich bei uns wie folgt.
Email: euhelp@1byone.com

ES
Para garantizar una rápida atención de su problema,
favor envíenos un email para ayudarle.
Email: euhelp@1byone.com

お客様の問題が直ちに解決されるため、ぜひメール
にて弊社までご連絡ください。

メール：

jphelp@1byone.com

Ask a Question ?