Full Text Searchable PDF User Manual
User Guide
Portable Wireless PA System
Portability
Simplicity
Flexibility
MA-707
16. Apparatus should not be exposed to dripping or splashing and no objects filled with
liquids, should be placed on the apparatus.
1. Read these instructions.
2. Keep these instructions.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarised or ground plug: A polarised plug has
two blades with one wider than the other. The wide blade is provided for your safety.
When the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plug,
convenience receptacles, and the point where they exit from the apparatus.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture.
3. Heed all warnings.
17. Use only with the battery which specified by manufacturer.
18. The power supply cord set is to be the mains disconnected device.
19. Where the MAINS plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
IMPORTANT SAFETY INSTRUCTION
S
Disposal
& IC - ID
This symbol indicates that dangerous voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.
“This product can only be used at the area that the altitude is lower than 2000m for
safety purpose.”
“This product can be used in non-tropical locations only for safety purpose.”
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device. This equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment.
THIS DEVICE COMPLIES WITH PART15 OF THE FCC RULES AND RSS-123 ISSUE2 OF
CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
WARNING
1. FOR OUTDOOR USE:
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture.
2. UNDER WET LOCATION:
Apparatus should not be exposed to dripping or splashing and no objects filled with
liquids, such as vases should be placed on the apparatus.
3. SERVICE INSTRUCTIONS:
CAUTION - These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
Disposing of used batteries with domestic waste is to be avoided!
Dispose of any unusable devices or batteries responsibly and in accordance
with any applicable regulations.
Batteries/NiCad cells often contain heavy metals such as cadmium(Cd),
mercury(Hg) and lead(Pb) that makes them unsuitable for disposal with
domestic waste. You may return spent batteries/accumulators free of charge
to recycling centres or anywhere else batteries/accumulators are sold.
By doing so, you contribute to the conservation of our environment!
Front Panel: Fig. 1
Rear Panel: Fig. 2
SCAN
CHANNEL
ACT
SENSITIVITY
NOISE
AF
RF
VOLUME
DC 24~32V
AC 100~240V
Steady: Full Charged
Flickering: Charging
+
Battery:12V/4AH
-
L
H
TONE
LINE IN
MIC1
LINE IN
MIC 2
LINE OUT
MIC 1
MIC 2
L
H
MASTER
POWER
Battery:12V/4AH
SCAN
CHANNEL
ACT
SENSITIVITY
NOISE
AF
RF
VOLUME
Ⅰ. Part Names, Fig. 1, 2, 3
Portable Wireless PA System
1
Control Panel: Fig. 3
L
H
TONE
LINE IN
MIC1
LINE IN
MIC 2
LINE OUT
MIC 1
MIC 2
L
H
MASTER
.
Battery Compartment Cover Plate
.
AC Power push button
.
.
Fixed Handle
Heat Sink
Rear Panel: Fig. 2
.
Master Power Switch with Battery Low Indicator
Trolley Wheels.
.
.
Retractable Carry Handle
Speaker Grille
.
AC Power Cord Socket
Front Panel: Fig. 1
.
Slot for Optional CD/USB Media Player Module
.
.
Microphone Storage Compartment
Tripod Stand Mount
.
Speaker
.
Slot for Optional Receiver Module
Passive Extension Speaker Socket.
.
Control Panel
.
DC 24-32V Power Connector
.
Battery Charging Status Indicator
.
Microphone 2 Volume Control
Line Input Volume Control.
.
High/Low Tone Control
: Unbalanced 6.3 Ø Microphone Input.
MIC 1
Control Panel: Fig. 3
6.3 Ø (1/4”) Line Output.
.
Master Volume Control
6.3 Ø (1/4”) Line
.
Input
.
Microphone 1 Volume Control
.
MIC 2: Balanced XLR Microphone Input
Portable Wireless PA System
2
We recommend the master volume control is turned to the maximum level. Next, adjust
volume of other audio input individually to avoid distortion with maximum dynamic range
output. Built-it audio limiter serves automatically to prevent the signal level from
exceeding a preset limit and stop sound from distorting.
4.
:
Wired Dynamic Microphone
Minimize all volume levels before turning on the Master Power Switch . A lit red
battery indicator denotes rechargeable battery is charged. A flashing red battery indicator
denotes rechargeable battery is low on power. Simply plug the supplied power cord into
the power socket on the back and the other end into an AC power outlet to recharge the
battery. Amplifier can be used simultaneously during charging.
2 Master Volume Control
.
:
1.
:
Power On
3
Jacks
. Line-input and Line-output 6.3 Ø (1/4”)
:
(A) Reduce the Line Input volume levels to minimum. Once powered on, adjust master
volume levels to maximum, and adjust line input volume to appropriate level.
(B) Line Output jack combines all mixed audio. Volume levels are individually adjusted,
and not related to master volume control.
(A) Reduce microphone volume levels to minimum. Once powered on, adjust master
volume levels to maximum.
Ø
(B) Plug an unbalanced 6.3 microphone into MIC 1 Input and adjust MIC 1 Volume
Control for desired sound level.
(C) Plug a balanced XLR microphone into MIC 2 Input and adjust MIC 2 Volume
Control for desired sound level.
.
(D) Adjust Tone Control for high or low tone sound quality
(E) The wired and wired microphones can be used at the same time, mixed and output
sound can be heard simultaneously.
Ⅱ. Operating Instructions
Portable Wireless PA System
3
Portable Wireless PA System
(C) MA-707-X Filler Panel, Fig. 4:
MA-707-X
(D) MRM-70B Part Names, Fig. 5:
Fig. 4
RF indicators.
Audio indicators.
Channel sync ACT button.
Power & Volume knob.
Channel display LED screen.
Sensitivity level adjustor.
Channel SCAN button.
Noise interference indicator.
Channel sync ACT window.
MRM-70B
SCAN
SENSITIVITY
NOISE
AF
RF
CHANNEL
ACT
VOLUME
Fig. 5
5.
:
Wireless Receiver Module
(A) Type of Wireless Receiver Module:
MRM-70B UHF PLL Diversity Receiver
:
.
(B) Installation:
(2)
(1) Up to two
wireless receiver modules can be installed.
(2) Each receiver has built-in Pilotone & NoiseLock circuitry which reduces noise interferences.
(3) Unscrew the 2 screws from the MA-707-X filler panel and remove the filler panel before installing
the receiver module. After the screws and filler panel have been removed, insert receiver module
into the empty slot and push it back to it's mating connector. Uses the screws removed previously
to fasten the receiver module in position.
4
Manually Search for a Receiver Channel: Press and hold SCAN button to
perform a manual channel search. Existing channel blinks to denote it is ready
to accept parameter changes. During blinking, press and hold Channel button to
force the channel to go forward to the next channel in order. Release Channel
button until a desired channel is located. This new channel is now saved. If
Channel button is not pressed within six blinks, it stops blinking and reverts back
to the existing channel, Fig. 7.
( )
B
( )
2 existing channel blinks.
(3) press & hold.
( )
4 a new forced channel
is saved.
(1) press & hold for
1 second.
ACT
Portable Wireless PA System
6. Operating Wireless Microphones:
(A) Reduce all volume levels to minimum. Once powered on, adjust master volume
levels to maximum.
(B) Power on the receiver module and reduce volume levels
to minimum.
(C) RF signal indictors are lit once receiver is powered on. Adjust receiver volume to
desired levels. Audio signal indicators expands and contracts, pending how loud
the input sound.
(D) Perform the channel synchronization between the receiver and transmitter by power
on the transmitter microphone and pressing the Channel sync ACT button and bring
the ACT windows within 30cm of each other. Once channel is synchronized
successfully, the RF signal indicators are lit and Audio signal indicators expands
and contracts, pending how loud the input sound.
7. Changing Receiver Channel:
(A) Scan Automatically for a Non-interference Receiver Channel: Press and hold SCAN
button to perform a channel scan. Existing channel blinks to denote it is ready to
accept parameter changes. During blinking, press and release SCAN button to scan
and stop for an open channel. This new channel is now saved. If SCAN button is not
pressed within six blinks, it stops blinking and reverts back to the existing channel,
Fig. 6.
( )
2 existing channel blinks.
(3) press & release.
( ) a new open channel
4
is saved.
( )
1 press & hold for
1 second.
ACT
F
ig. 6
Fig. 7
5
(B) When two or more receiver modules are installed, therefore, two or more compatible
channels are required to be used simultaneously at the same place.
(A) Noise or interference is heard during a presentation or performance.
(A) Do not attempt to change a new receiver channel during a performance where two or
more transmitters/microphones are being used simultaneously to avoid interferences
with each other generated by the transmitting microphone signals.
9. Caution:
8
:
. Reason for Changing a New Receiver Channel
(C) If ACT channel synchronization is performed successfully, the new channel in
Channel Display Screen stops blinking, RF indicators are lit and audio indicators are
lit once you speak into the microphone.
(B) Align the ACT sync windows of both transmitter and receiver within 30cm of each
other for an automatic channel synchronization, Fig. 8.
10 .ACT Channel Synchronization:
_”
(B) “ displays in Channel display screen denotes this receiver channel is currently
experiencing interference, therefore, scan for a new, open receiver channel
(A) Ascertain both receiver and transmitter are powered on. Press ACT button on
receiver to activate IR (infrared) channel synchronization. Existing channel blinks
.
Portable Wireless PA System
Fig 8
.
DIVERSITY RECEIVER
SCA N
ACT
SE NSIT IVI TY
CHA NNE L
AF
RF
NOIS E
VOLUME
DIVERSITY RECEIVER
SCA N
ACT
SE NSIT IVI TY
CHA NNE L
AF
RF
NOIS E
VOLUME
DIVERSITY RECEIVER
SCAN
ACT
SENSITIVITY
CHANNEL
AF
RF
NOISE
VOLUME
or
6
Ⅲ. Connection for External Audio Sources, Fig. 9
Fig. 9
Portable Wireless PA System
L
H
TONE
LINE IN
MIC1
LINE IN
MIC 2
LINE OUT
MIC 1
MIC 2
L
H
MASTER
7
Cassette Recorder
Amplifier
Mixer
CD Player
MP3 Player
Cable no: 2FA030
Cable Mic.(XLR Connector)
Cable Mic.(6.3 Ø Connector)
Cable no: 2FA031
Mobile Phone
Portable Wireless PA System
Ⅳ. Power Supply
1. AC Power Supply:
(A) Connect AC Power Cord Socket and plug the system into an AC outlet to charge
the built-in rechargeable batteries. The AC Power and Battery Status Indicator
blinks red during charging. The AC Power and Battery Status Indicator glows red and
stops blinking when it is fully charged.
(C)
CAUTION: AC Power push button needs to be pressed (recessed) when
plugging the system into an AC outlet. The system cannot provide AC power
if the AC Power push button itself is raised.
2. DC Power Supply:
(A) Two built-in series connection model WP 4.5-12 lead-acid batteries are used.
(B) Fully charged batteries will yield approximately 7 hours of continuous music and
speech. However, service times vary depending on control settings.
( ) AC Power push button needs to be pressed (recessed) when plugging the system
into an AC outlet for battery charging. The system cannot provide AC power if the AC
Power push button itself is raised.
C
( ) The Battery Charging Status Indicator will not glow unless Master power is
turned on. The LED light on Master power glows red when turned on denotes normal
status. The LED light on Master power flashes red when turned on denotes battery
low status. Simply plug into an AC outlet to recharge the battery. The LED light on
Master power do not glow or flashes red (light is off) when turned on denotes over-
discharged, abnormal or faulty status.
D
E Always store system with the batteries fully charged. To preserve built-in battery life,
we recommend to fully charged before the first use and after each use. Leave the
system plugged into an AC power outlet when not in use. Battery may not hold a
charge if they are not recharge often. Recharge the system at least once every 3
months. Remove the batteries when the system will not be used for an extended
period of time.
( )
(B) AC power provides powers to both the system itself and to the built-in rechargeable
batteries. Power switches to DC automatically from AC if the AC plug is detached
during operations. Operation works normally in both AC or DC mode. DC power
works only if it has built-in rechargeable batteries.
8
Portable Wireless PA System
3
.
Caution: AC and DC Power supply cannot be used at the same time.
(F) How to “rescue” rechargeable battery that is not used for a long time, not recharged
properly, stored in extremely high temperature environments, resulting in excessive
discharged and charging failure? First step, remove the battery and charge it by
18V/2A DC power supply for more than 30 minutes and ascertain battery surface
temperature cannot exceed 50℃ during charging. Then, install the battery back into
the system and turn on the power. The LED light on Master power flashes red
after powered on denotes battery can be recharged normally. If the LED light on
Master power is not on once powered on, it denotes battery can no longer holds a
charge, therefore, a replacement new battery is required.
Ⅴ. Installation of MIPRO CD/MP3 Media Player
(B) Gently insert the MP3 media player module into the slot. Make sure the back edge
connector is aligned and firmly connected.
2. Operations of CD/MP3 Media Player: See a separate player manual
enclosed in the master carton.
(C) Tighten up the screws.
(A) Using a Phillips-head screwdriver (not supplied) remove the screws to remove
protection cover panel.
1.
Installation Steps:
9
Ⅵ. Helpful Operating Tips
1.
Minimized the master volume control before powering on. Adjust the
volume controls afterwards.
2. Each audio input volume can be individually controlled and mixed out
through the amplifier.
3. Each audio input can be broadcasted and recorded at the same time.
7. Refer to operating instructions for wireless microphone system.
8. Refer to actual product in the event of product description discrepancy.
6. Detached the power cord from AC power outlet once the system is fully-
recharged.
9. Frequency range, output power and maximum deviation to comply with the
regulations of different countries.
4. This PA system can be installed with an optional wireless microphone
system.
5. We recommend placing sound system between the target audience and the
presenter, facing the audience and raised above their heads using an
optional speaker stand or table stand. This set-up helps prevent the
annoying feedback by keeping wireless & wired microphone users behind
the sound system. The internal power supply rechargeable batteries should
be kept fully charged. Always charge the system after use.
Portable Wireless PA System
10
All rights reserved. MN 019/01
Do not copy or forward without prior approvals MIPRO.
Specifications and design subject to change without notice.
Tel
886.5.238.0809
:+
www.mipro.com.tw
Fax
886.5.238.0803
:+
mipro@mipro.com.tw
MICROPHONE PROFESSIONALS
Headquarters: 814 Pei-Kang Road, Chiayi, 60096, Taiwan
2 CE3 9 4 D