Full Text Searchable PDF User Manual
Manual Instruction
Introduction:
Thanks for your purchase of a VOOPOO
product.In order for you to have better use of
all the functions of this product,please carefully
read the operation notes and detailed
functional instructions before your first use of
this product.If you have any problems with
using this product,please contact our local
agent or visit our our official website at
www.voopootech.com
Specifications
:
Product Name
:
VMATE
Size
:
89*47*30mm
Output power
:
5-200W
Battery
:
18650*2
Output Voltage
:
0-7.5V
Charging Current
:
2000mA
Charging Voltage
:
5V
Resting Current
:
≤20uA
Resistance Range
:
TC Mode
:
0.05-1.5Ω
VW Mode
:
0.05-3.0Ω
Temperature Range
:
200-600°F/100-315
℃
Upgraded Function
:
YES
1
2
Product Appearance
510 Thread
Power Button
UP/DOWN Button
OLED Screen
USB Port
Operating Instructions:
A. How to turn on/off:
Press the fire button 5 times rapidly.
B. How to switch between Power and
Temperature modes:
Press the fire button 3 times rapidly to
rotate between modes. (W→SS316→
Ni200→Ti).
C. TC mode operating instructions:
When the temperature setting is at
100°C, keep pressing down button, it will
turn to be 600
℉
.
When the temperature setting is at 200
℉
, keep pressing down button, it will
turn to be 315°C.
Adjustment rate: 1
To adjust wattage while in TC Mode, press
fire button 4 times rapidly to activate
wattage adjustment. You will see the “W”
wattage icon flashing. The wattage can be
adjusted from 10W to 80W.
D. Adjust the wattage:
Adjust the wattage from 5w to 200w.
Adjusting rate: Short time Press: 0.1, Long
time press: 0.5.
3
a. The product automatically recommends
the output wattage according to the
resistance of the atomizer when it detects
that a new atomizer has been attached.
E. Key Combination instruction:
a. Press up and down buttons at the same
time for 1.5s to enter the function Menu
interface.
b.Press Power Button and Up Button at the
same time for 1.5 seconds to lock the
mod
(
Notice
:
Up Button and Down Button
don't work after being locked
,
but
combination key for operation is OK
)
F. Function Menu:
Press up and down buttons at the same
time for 1.5s to enter the function menu
interface→Press up down button to scroll
through the menu options→Press fire
button to confirm your selections→Press
up or down button to make your
adjustment→Press and hold the fire
button for 1.5s to confirm and save,
4
a. The product automatically recommends
the output wattage according to the
resistance of the atomizer when it detects
that a new atomizer has been attached.
E. Key Combination instruction:
a. Press up and down buttons at the same
time for 1.5s to enter the function Menu
interface.
b.Press Power Button and Up Button at the
same time for 1.5 seconds to lock the
mod
(
Notice
:
Up Button and Down Button
don't work after being locked
,
but
combination key for operation is OK
)
F. Function Menu:
Press up and down buttons at the same
time for 1.5s to enter the function menu
interface→Press up down button to scroll
through the menu options→Press fire
button to confirm your selections→Press
up or down button to make your
adjustment→Press and hold the fire
button for 1.5s to confirm and save,
and the display will return to the main
display interface.
a. Under Power Mode the Function Menu
interface has the following options:
Regular Mode , Custom Mode ,
Locked Mode , Series Number
,
Software Version ( 5 options in total).
b. Menu under TC mode:
Regular Mode , Custom Mode , Coil
Cooling Value , Coil Coefficient ,
Locked Mode ( 5 options in total).
Tips:
Under the lock mode, it is invalid to press
the up , down or the fire button separately.
5
and the display will return to the main
display interface.
a. Under Power Mode the Function Menu
interface has the following options:
Regular Mode , Custom Mode ,
Locked Mode , Series Number
,
Software Version ( 5 options in total).
b. Menu under TC mode:
Regular Mode , Custom Mode , Coil
Cooling Value , Coil Coefficient ,
Locked Mode ( 5 options in total).
Tips:
Under the lock mode, it is invalid to press
the up , down or the fire button separately.
While it is valid to operate the combination
key and to turn on/off the device.
G.
Custom Mode:
Press up and down buttons at the same
time for 1.5s to enter the function menu
interface→Press up or down button to
select the customization menu→Press
the fire button to confirm and the display
will change to the Custom Mode
interface.
Under custom Mode, rapidly press the fire
button for 3 times to switch the 4 custom
mode options: Stable power (W) mode
and the 3 TC control Modes:
TC-ss316/TC-Ni200/TC-Ti.
a. Press up or down button to scroll
between modes M1 to M5.
b. Press fire button 4 times rapidly to enter
the custom power or temperature curve
6
While it is valid to operate the combination
key and to turn on/off the device.
G.
Custom Mode:
Press up and down buttons at the same
time for 1.5s to enter the function menu
interface→Press up or down button to
select the customization menu→Press
the fire button to confirm and the display
will change to the Custom Mode
interface.
Under custom Mode, rapidly press the fire
button for 3 times to switch the 4 custom
mode options: Stable power (W) mode
and the 3 TC control Modes:
TC-ss316/TC-Ni200/TC-Ti.
a. Press up or down button to scroll
between modes M1 to M5.
b. Press fire button 4 times rapidly to enter
the custom power or temperature curve
menu (Under power mode, the upper right
corner will show the adjustment power
value. Under TC custom mode, the upper
right corner shows the adjustment
temperature control value.)
Press up or down button to make
adjustment→Press the fire button and
move to the next increment→When you
finish the curve adjustment, press and
hold the fire button for 1.5s to confirm and
save. The display will return to the custom
mode interface.
H. Sleep Mode:
If the device is not operated for 10s, the
screen will automatically turn off. After
15 minutes without any operations after
the screen turns off, the device will enter
sleep mode. If resistance was changed
7
before sleeping mode, screen will display
the prompt “NEW Coil YES/NO” on
interface; Press the fire button to recover
display form sleep mode.
I. Computer customization
:
You can do the following customization
operations
via the voopoo Firmware: Prompt
page, Temperature coefficient, temperature
curve, wattage curve, increase/increase coil
type and device upgrade etc.
J. When the device is connected to an
external power supply (5V) using the USB
charging port, it will enter charging mode.
Charging mode of the first 10s, the battery
small icon will run as the battery charging
which shows that charging began. With
10s without any operation, the device will
enter power saving mode, and the
full-screen will display battery power as a
large icon running. When the power is full,
the icon will be seen as below.
8
before sleeping mode, screen will display
the prompt “NEW Coil YES/NO” on
interface; Press the fire button to recover
display form sleep mode.
I. Computer customization
:
You can do the following customization
operations
via the voopoo Firmware: Prompt
page, Temperature coefficient, temperature
curve, wattage curve, increase/increase coil
type and device upgrade etc.
J. When the device is connected to an
external power supply (5V) using the USB
charging port, it will enter charging mode.
Charging mode of the first 10s, the battery
small icon will run as the battery charging
which shows that charging began. With
10s without any operation, the device will
enter power saving mode, and the
full-screen will display battery power as a
large icon running. When the power is full,
the icon will be seen as below.
K. Adding, removing or changing
temperature control coil types using the
Voopoo Firmware.
(Default: SS316,Ni200,TI) You can select 1
to 5 types. Coil coefficient setting and
selecting Serial coil mark coefficient select
L. Function tips:
TIME OUT COIL NO(-)
NEW YES(+) LOW POWER
Index Type Icon Coefficient Select
1 SS316 SS
1300
2 Ni200 Ni
6500
3 Ti Ti
4000
4 NC NC
400
5 TCR TC
1000
9
K. Adding, removing or changing
temperature control coil types using the
Voopoo Firmware.
(Default: SS316,Ni200,TI) You can select 1
to 5 types. Coil coefficient setting and
selecting Serial coil mark coefficient select
CHECK BATTERY ATOMIZER SHORT
CHECK ATOMIZER HIGH ATOMIZER
TEMP HIGH LOCK
OFF UNLOCK
M. Tips
:
a. Charging rate: 3H (Requirement: 5V 2A
supply only).
b. Accommodation coefficient of the TC
wire:
Ni: 6000-7000 Standard Default Value: 6500
Adjusting Rate: Short time press:1, long
time press: 10
Ti: 3500-4500 Standard Default Value: 4000
Adjusting Rate: Short time press:1, long
time press: 10
SS: 1000-1600 Standard Default Value: 1300
Adjusting Rate: Short time press:1, long
time press: 10
NC: 200-600 Standard Default Value: 400
Adjusting Rate: Short time press:1, long
time press: 10
TC: 100-7000 Standard Default Value: 1000
Adjusting Rate: Short time press:1,
10
M. Tips
:
a. Charging rate: 3H (Requirement: 5V 2A
supply only).
b. Accommodation coefficient of the TC
wire:
Ni: 6000-7000 Standard Default Value: 6500
Adjusting Rate: Short time press:1, long
time press: 10
Ti: 3500-4500 Standard Default Value: 4000
Adjusting Rate: Short time press:1, long
time press: 10
SS: 1000-1600 Standard Default Value: 1300
Adjusting Rate: Short time press:1, long
time press: 10
NC: 200-600 Standard Default Value: 400
Adjusting Rate: Short time press:1, long
time press: 10
TC: 100-7000 Standard Default Value: 1000
Adjusting Rate: Short time press:1,
long time press: 10
Attention:
1) The higher coil coefficient you set, the
higher coil temperature you get.
2) Because of the different material for the
wire, you may feel the power is not strong
enough when vaping, you can properly
adjust the coil coefficient at a higher rate
to get a better vape experience.
3) Please adjust the coil coefficient at a low
rate, if too high there is a risk of firing
cotton.
C. Coil cooling value: 0.05
~
1.50Ω, adjusting
rate: 0.01Ω. This function is only available
under temperature control mode.
Attention:
a. Before use please carefully read the user
manual.
b. Please keep device away from heat, fire and
water.
c. Please do not drop, throw or immerse the
device in water as the out shell or inner
components may be damaged.
11
long time press: 10
Attention:
1) The higher coil coefficient you set, the
higher coil temperature you get.
2) Because of the different material for the
wire, you may feel the power is not strong
enough when vaping, you can properly
adjust the coil coefficient at a higher rate
to get a better vape experience.
3) Please adjust the coil coefficient at a low
rate, if too high there is a risk of firing
cotton.
C. Coil cooling value: 0.05
~
1.50Ω, adjusting
rate: 0.01Ω. This function is only available
under temperature control mode.
Attention:
a. Before use please carefully read the user
manual.
b. Please keep device away from heat, fire and
water.
c. Please do not drop, throw or immerse the
device in water as the out shell or inner
components may be damaged.
d. Please use the proper working mode for
your atomizer’s design and material.
e. If the device is not used for a long time,
please let it be charged periodically to
avoid discharging.
f. Keep the contents of this package out of
reach of children and animals.
g. This product is intended for use with
various strengths of e liquid, if you come
into direct contact with such liquid whilst
using this product please wash your hands
and forearms thoroughly.
Exposure to such liquid can be harmful if
it gets into your eyes, in which case flush
your eyes with water and seek medical
attention. If swallowed, rinse out your
mouth and seek immediate medical
attention. When seeking medical advice,
have the liquid product container or label
at hand.
12
d. Please use the proper working mode for
your atomizer’s design and material.
e. If the device is not used for a long time,
please let it be charged periodically to
avoid discharging.
f. Keep the contents of this package out of
reach of children and animals.
g. This product is intended for use with
various strengths of e liquid, if you come
into direct contact with such liquid whilst
using this product please wash your hands
and forearms thoroughly.
Exposure to such liquid can be harmful if
it gets into your eyes, in which case flush
your eyes with water and seek medical
attention. If swallowed, rinse out your
mouth and seek immediate medical
attention. When seeking medical advice,
have the liquid product container or label
at hand.
h. Do not use if pregnant or breast feeding.
i. Do not use if you have an unstable heart
condition, severe hypertension or
diabetes.
j. This product contains nicotine which is a
highly addictive substance.
k.
1) EEE Recycling:
This product should not be treated as
household waste, instead it should be
handed over to the applicable collection
point for the recycling of electrical and
electronic equipment.
2) Battery Recycling:
This products battery should not be
treated as household waste, instead it
should be handed over to the applicable
used battery collection point for recycling.
13
Manufacture:
Shangliao Haosi Linpokeng
Industrial Zone, Nanpu Rd,
Shajing St, Bao'an District,
Shenzhen, Guangdong, China.
www.voopootech.com
Facebook.com/voopootech
Contact in EU:
Vaping Legal Ltd
Address: Armstrong House, First
Avenue, Robin Hood
Airport, Doncaster. DN9
3GA. United Kinged
Email: compliance@tpdcompliance.eu
Designed by Voopoo in California
www.voopootech.com
Made in China