Motorline MC2 User's And Installer's Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

v1.0

REV. 04/2015

MC2

USER / INSTALLER MANUAL

MC2

INDEX

STANDARDS TO FOLLOW

00. CONTENT

01. SAFETY INSTRUCTIONS

11
11

2A
3A

10A

10B

6B
8A

ATTENTION:

• To ensure the safety of people, it is important that you read all the following instruc-

tions.

• Incorrect installation or incorrect use of the product can cause physical injury and

material damage.

• This product was designed and produced strictly for the use indicated in this manual.

Any other use, not expressly indicated here, could compromise the good condition/ope-

ration of the product and/or be a source of danger, and will void the warranty.

•

ELECTROCELOS S.A.

is not responsible for the improper use of the product, or other

use than that for which it was designed.

•

ELECTROCELOS S.A.

is not responsible if safety standards were not taken into ac-

count when installing the equipment, or for any deformation that may occur to it.

•

ELECTROCELOS S.A.

is not responsible for the safety and proper operation when

using components not sold by them.

• Do not make any modifications to the operator components and / or their accessories.

• Before installation unplug the automatism from the source of power.

• The installer must inform the client how to handle the product in case of emergency

and provide this manual to user.

• Keep remote controls away from children, to prevent the automated

system from being activated involuntarily.

• The customer shall not, under any circumstances, attempt to repair or tune the auto-

matism. Must call qualifid technician only.

• Connect the automatism to a 230V plug with ground wire.

• Control board for indoor use.

STANDARDS TO FOLLOW

TECHNICAL SPECIFICATIONS

PROGRAMMING PRE-RECOMENDATIONS

MAIN MENU

EXTENDED MENU 3

PHOTOCELLS TESTING AND REMOTE CONTROLS

INSTRUCTIONS FOR FINAL CONSUMERS

EXTENDED MENU 1

RESET OF CONTROL BOARD

CAPACITATOR SCHEME

INSTRUCTIONS FOR SPECIALIZED INSTALLERS

EXTENDED MENU 2

01. SAFETY INSTRUCTIONS

02. THE CONTROL BOARD

03. CONFIGURATION

04. COMPONENT TEST

05. TROUBLESHOOTING

CONTROL BOARD CONNECTION COMPONENT

06. CONNECTION SCHEME

02. THE CONTROL BOARD

TECHNICAL SPECIFICATIONS

The MC2 is a central electronic single phase with incorporated radio, for automation of

swing gates.

•

Power supply

230V AC 50-60Hz

•

Lightbulb’s output

230V AC 500W máx.

•

Motor’s output

230V AC 50/60 Hz 500W máx.

•

Auxiliary accessories output

24V AC 15W máx.

•

Safety and remote controls in BT

24V CC

•

Working temperature

-10˚C to +55˚C

•

Protection

IP56

•

Incorporated Radio Receiver

433,92 Mhz

•

OP Transmitters

12-18 bits or Rolling Code

•

Maximum memory capacity

150 (CODE or CODE PED)

• CONNECTOR’S DESCRIPTION

• DIMENSIONS THE BOX AND CONTROL BOARD

• Earth connection

• AC 230V Line Input (PHASE)

• AC 230V Line Input (NEUTRAL)

• Lightbulb / Courtesy light’s output (not blink) AC230V (NEUTRAL)

• Lightbulb / Courtesy light’s output (not blink) AC230V (PHASE)

• Motor’s Output 1 opening

• Motor’s Output 1 common

• Motor’s Output 1 closing

• Motor’s Output 2 opening

• Motor’s Output 2 common

• Motor’s Output 2 closing

• Output for power photocells 24V AC

• Output for power photocells (earth)

• Output for electric lock 12V DC 15W (+12V)

• Output for electric lock 12V DC 15W (earth)

• Input PUL button the order opening / closing (NA)

• Input earth common

• Input PUL PED button the order pedestrian (NA)

• Input DS1 safety device 1 (NC)

• Input common GND

• Input DS2 safety device 2 (NC)

• Antenna mass input

•

Antena hot pole input

CN2

CN3

CN1

205mm

115mm

140mm

252mm

125mm

02. THE CONTROL BOARD

PROGRAMMING PRE-RECOMENDATIONS

• POWER AND SPEED OF MOTORS

The control board has a trimmer VR1 for adjusting the force and speed

of the motors controlled by the microprocessor. The adjustment can be

effected between 50% and 100% the power.

At each start-up movement, the control board applies the maximum

power during 2 seconds, even when it is made regulating force to a value

than not the maximum.

FORZA

When you adjust the trimmer VR1 has to remake course programming, as they

could varied the times of maneuvering and deceleration.

• PROGRAMMING THE CONTROL BOARD - BUTTONS SEL/SET

SEL button:

It makes the selection of the function to change. The se-

lection is identified by the flashing of the LED corresponding to the

selected function at that time.

Pressing the SEL button repeatedly will cycle through the various

functions to be programmed. The selection remains active for 10 se-

conds, after these time the control board returns to original status

(no active selection).

SET button:

Makes programming the selected function through the

SEL button.

The SET button may be substituted by a remote control from the latter is pro-
grammed.

SET

SEL

• OPERATION OF FLASH LAMP

The operation of the output is conditioned by the mo-

vement of the motor and automatic closing. When the

automatic closing is activated, the 230V output is ac-

tivated even during pause time.

3 4

• OPERATION WITH TIMER

Instead of a push button opening / closing (PUL), the

control board can be operated with a TIMER. With a

TIMER connected to the control board it is possible

to program an exact time for that the motor perform

both the opening and closing, in the automatic mode.

5 6

CN3

CN2

Flash lamp:

03 and 04

•

This output allows connection of a flash lamp (

see page 4B

Capacitor:

05 and 07

•

You must connect the capacitor between the outputs 05 and 07.

08 and 10

• You must connect the capacitor between the outputs 08 and 10.

Electric lock:

03 and 04

• This output allows connection of an electric lock (

see pág.9A

)

Push button / selector:

• Allows connection the push-button / selector to full opening (NA).

Safety circuits:

•

This circuit allows the connection of all types of safety devices such as

photocells, safety edge, etc.

This device operates only in the gate closing and, when activated change the

direction of the automation.

• This circuit allows the connection of all types of safety devices such as

photocells, safety edge, etc.

This device operates in the opening and closing. In closing, change the direction

of the automation. In the opening for the movement and when was released

continues with the opening.

CN2

CN3

CN1

1 2 3

1 2 3 4 5 6 7 8 9

1 2 3 4 5 6 7 8 9 10 11 12

CN2

CN3

Before proceeding to the control board configuration, note the following points listed

in the table below:

03. CONFIGURATION

The control board allows starting only one motor for the possible passage of peoples.

With this function, pressing the remote control, only the leave of motor 1 will open.

Programming the remote controls to pedestrian mode (LED CODE PED ON) / the remote

controls (LED CODE OFF):

01.

Press the

SEL

button once until the

LED CODE PED

starts flashing.

02.

Press the remote control button that you want to program during 1 second.

If you want delete remote controls, press the SET button for 1 second.

03.

LED CODE PED

ON indicates that the remote controls is programmed and deleted

LED indicates that the remote controls have been deleted.

• CODE PED |

PEDESTRIAN OPERATION

MAIN MENU

Mode automatic operates (LED AUT / P-P off):

•

The first impulse the remote control / puss button activates the opening until the end

of the motor time.

•

The second impulse the remote control / puss button activates the closing until the end

of the motor time.

If give an impulse before the end of the motor time, the control board will perform a inver-

sion of movement in opening and closing.

Mode of operation step by step (LED AUT / P-P on):

•

The first impulse the remote control / puss button activates the opening until the end

of the motor time.

•

The second impulse the remote control / puss button activates the closing until the end

of the motor time.

If give one order before the end of the motor time, the control board will stop the move-

ment in opening and closing. A new order will return the operation, performed in the other

direction to what it was before the stop.

The control unit is supplied by the manufacturer with the activated Automatic mode (LED

AUT / P-P off).

Note:

If the T. PAUSE is active (on) and stop the gate during the opening, this will keep

stopped until the end of the pause time, and then make the closing. If you stop during

• AUT/P-P |

AUTOMATIC OPERATION / STEP BY STEP

The control board accepts only Dip-Switch remote controls or Rolling Code MOTORLINE,

and has a maximum capacity of 150 remote controls. When trying to program the 151

remote controls, all the programming LEDs will flash simultaneously to indicate that the

memory is full.

To program new remote controls:

01.

Press the

SEL

button as many times as necessary until the

LED CODE

flashes.

02.

Press once the button remote control you want to program for 1 second.

03.

The

CODE LED

lights up permanently, indicating successful programming.

To delete all configured remote controls:

01.

Press the

SEL

button once, and the

CODE LED

will begin to flash.

02.

Press the

SET

button once! The

CODE LED

turns off and all remote controls have been

deleted.

If the

CODE LED

starts fast flashing, means that the control board did not accept the

remote controls programming, because of the following reasons:

• The remote control is already programmed;

• The control board accepts only remote controls with rolling code.

• CODE |

PROGRAMMING OF REMOTE CONTROLS

closing, it will stop and will restart only when receive new order.

Select operating mode:

01.

Press the

SEL

button once, and the

LED AUT / P-P

will start flashing.

02.

Press the

SET

button for 1 second.

03.

The

LED AUT/PP

lit signals that are selecting the mode of operation step by step and

the LED off signals that is selected the automatic mode.

MAIN MENU

LED

LED OFF

LED aceso

• AUT/P-P

LED OFF

Step by step

• CODE

Automatic

Inserted code

• CODE PED.

No code

Inserted code

• INB. CMD. AP

No code

Activated

• T. MOT.

Deactivated

Programmed time

• T. MOT. PED

Motor time 30 s.

Programmed time

• T. PAUSA.

Motor time pedestrian 10 s.

With automatic closing

• T. RIT. ANTE

Without automatic closing

Programmed time

This is the main menu of the control board MC2, which has access to the most impor-

tant functions of its operation. The control board is supplied with the active main menu.

03. CONFIGURATION

MAIN MENU

With this function can actuate the slowdown, decreasing the gate's movement speed.

NOTA

•

To perform this programming is necessary that the motors have limit switch or

mechanical stop.

Instead of using the

SET

button of the control board, you can use a remote control that

is already programmed.

The control board is supplied by the manufacturer with a working time of motors estab-

lished within 30 seconds, without deceleration.

Program working time of the motor with deceleration (Gate closed):

01.

Press the

SEL

button the times necessary until the

LED T.MOT.

start to flash.

02.

Press the

SET

button for 1 second, so that the Motor 1 start opening.

If the motor

does not accept the opening, invert the cable connections 5 and 7, the CN2 connector

(see page 2B).

03.

Press the

SET

button for 1 second, when the gate is the desired point to start dece-

leration.

04.

Press again

SET

button when you want to establish the opening limit switch. At this

time,

LED T. MOT.

will quickly flashing and automatically the motor 2 starts opening ma-

neuver.

05.

Press the

SET

button for 1 second, when the gate is in the desired point to start de-

celeration.

06.

Press again

SET

button when you want to establish the opening limit switch.

07.

The

T. MOT.

will quickly flashing indicating that programming for closing can be per-

formed and automatically the motor 2 starts the closing maneuver. Repeat the process

to program the closing.

• T. MOT AND DECELERATION |

MOTOR TIME PROGRAMMING AND DECELERATION

To activate the pedestrian function, the control board allows to be just activated the

operation of motor 1.

NOTE

•

To perform this programming is necessary that the motors have limit switches

or stoppers.

Instead of using the

SET

button on the control board, you can use a remote control that

is already programmed.

The control board is supplied by the manufacturer with a pedestrian working time es-

tablished in 10 seconds without deceleration.

Programming pedestrian working time with deceleration (gates closed):

01.

Press

SEL

button as often as necessary until the

LED T. MOT. PED.

starts flashing.

02.

Press the

SET

button for 1 second, so that the Motor 1 start opening.

If the motor

does not accept the opening, invert the cable connections 5 and 7, the CN2 connector

(see page 2B).

03.

Press the

SET

button for 1 second, when the gate is the desired point to start de-

celeration.

04.

Press again

SET

button when you want to establish the opening limit switch. At

this time,

LED T. MOT.

will quickly flashing and automatically the motor 1 starts closing

maneuver.

05.

Press the

SET

button when the gate is in the desired point to start deceleration.

06.

Press again

SET

button when you want to establish the closing limit switch.

07.

The

LED T. MOT.

will light, signaling that the working time is programmed.

• T. MOT. PED |

PROGRAMMING PEDESTRIAN WORKING TIME

Program working time of the motor without deceleration (Gate closed):

01.

Press the

SEL

button the times necessary until the

LED T.MOT.

start to flash.

02.

Press the

SET

button for 1 second, so that the Motor 1 start opening. If the motor

does not accept the opening, invert the cable connections 5 and 7, the CN2 connector

(see page 2B).

03.

Press twice the

SET

button when the gate is in the desired point to finish the opening

course. At this time,

LED T. MOT.

will quickly flashing and automatically the motor 2 starts

opening maneuver.

04.

Press

SET

button two times when desires to establish the opening limit switch.

05.

The

T. MOT.

will quickly flashing indicating that programming for closing can be per-

formed and automatically the motor 2 starts the closing maneuver. Repeat the process

to program the closing.

With the function activated, the control board rejects all the remote controls signals

during the opening maneuvers and automatic pause time. It’s important that this func-

tion is activated during a magnetic loop installation, because the control board will

ignore the crossings performed during the opening and the pause time.

The control board is supplied by the manufacturer with this function deactivated.

Activate (LED ON) / deactivate (LED OFF) function:

01.

Press the

SEL

button the times necessary until the

LED INB CMD AP

starts to flash.

02.

Press

SET

button for 1 second to enable / disable the function.

03.

The

LED INB CMD AP ON

indicates that the function is active and the

LED OFF

indi-

cates that the function is deactivated.

• INB. CMD. AP |

TRANSMITTER INHIBITION DURING THE OPENING AND PAUSE TIME

03. CONFIGURATION

MAIN MENU

The control board permits an automatic closing after a set waiting time, maximum until

4 minutes.

The control board is supplied by the manufacturer with this function disabled.

NOTE

•

Instead of using the

SET

button on the control board, you can use a remote

control that is already programmed.

Activate (LED ON)/deactivate (LED OFF) function:

Press

SEL

button as often as necessary until the

LED T. PAUSA

starts flashing.

Press the

SET

button for 1 second. From that moment, the waiting time before pres-

sing

SET

will be equal to the time that the gate stays open.

Press the

SET

button for 1 second, when you reach the time that you want for the

automatic closing.

The

LED T.PAUSA

indicates that the function is active and the LED off indicates

that the function is disabled.

• T. PAUSA |

PROGRAMMING AUTOMATIC CLOSING

The control board is supplied by the manufacturer with an extended menu 1, which

allows access to more functions of the control board.

To access the options of extended menu 1 follow these instructions:

01.

Press continuously the

SET

button for 5 seconds and the

LED T.PAUSA

and

LED T.

RIT. ANTE

will flash alternately.

02.

You have 30 seconds to select functions from the extended menu 1 (using the

SEL

and

SET

button), and that after this time the control board returns to main menu.

This function can delay up to 15 seconds the start of the closing motor 1 in relation to

the motor 2.

At the opening, the difference between the motor starting motor 2 to 1 is always 2 se-

conds.

The unit is supplied by the manufacturer with this function disabled.

Programming:

01.

Press the

SEL

button as often as necessary until the

LED T. RIT. ANTE

starts flashing.

• T. RIT. ANTE |

PROGRAMMING DOOR DELAY

EXTENDED MENU 1

LED

LED OFF

LED ON

• AUT/P.P.

PGM distance

OFF

PGM distance

• CODE

Photocells test

OFF

• CODE PED.

Pressure maintenance

OFF

Pressure maintenance

• INB. CMD. AP

Opening push

OFF

Opening push

• T. MOT.

Closing push

OFF

Closing push

• T. MOT. PED

Safety device 2

Blockade entrance

• T. PAUSA.

Alternative intermittence

ON/OFF

• T. RIT. ANTE

Alternative intermittence

ON/OFF

EXTENDED MENU 1

02.

Press the

SET

button for 1 second. From that moment, the waiting time before pres-

sing

SET

will be equal to the time that the gate stays open.

03.

Press the

SET

button for 1 second, when you reach the time that you want. Therefo-

re, on closing, the delay time will be stipulated by the option while the opening is fixed

in 2 seconds.

04.

The

LED T. RIT. ANTE

will light permanently, indicating the memorization time delay

between motor 1 and motor 2.

Delete programming:

01.

Press the

SEL

button until the

LED T. RIT. ANTE

will flashing.

02.

Press the

SET

button twice in less than 2 seconds.

03.

The

LED T. RIT. ANTE

will off, signaling the success of the operation.

Programming pedestrian working time without deceleration (gates closed):

01.

Press

SEL

button as often as necessary until the

LED T. MOT. PED.

starts flashing.

02.

Press the

SET

button for 1 second, so that the Motor 1 start opening.

If the motor

does not accept the opening, invert the cable connections 5 and 7, the CN2 connector

(see page 2B).

03.

Press twice the

SET

button, when you want to establish the opening limit switch. At

this time,

LED T. MOT.

will quickly flashing and automatically the motor 1 starts closing

maneuver.

04.

Press twice the

SET

button when you want to establish the closing limit switch.

05.

The

LED T. MOT.

will light, signaling that the working time is programmed.

03. CONFIGURATION

EXTENDED MENU 1

The control board is supplied by the manufacturer with the deactivated photocells test.

Activate (LED ON)/deactivate (LED OFF) function:

01.

Activate the extended menu 1

02.

Press

SEL

button once and the

LED AUT/P-P

will begin to flash.

03.

Press

SET

button for 1 second

04.

The

LED CODE ON

indicates that the function is disabled and the LED off indicates

that the function is activated.

NOTE

•

If you do not have the photocells installed, this test will not work.

• CODE |

TEST OF PHOTOCELLS

The pressure function of the motors, makes that with control board send the order of 2

seconds of closing, once every two hours.

The control board is supplied by the manufacturer with functionality to keep pressure

OFF the hydraulic motors.

Activate (LED ON)/deactivate (LED OFF) function:

01.

Activate the extended menu 1.

02.

Press

SEL

button as often as necessary until the

LED CODE PED

will flashing

• CODE PED |

MOTORS PRESSURE

With the blocking function activated whenever the photocells (DS2) detected an obsta-

cle, the gate movement will stop and only again be triggered when you press the remote

control button. Before the gate resume movements, the flash lamp will flash during 5

seconds.

The control board is supplied by the manufacturer with blocking disabled.

With the closing push function, the control board case is programmed with decele-

ration, will add 1 second acting at full motor power, so that the gate can overcome

the lock.

The control board is supplied by the manufacturer with the closing push disabled.

Activate (LED ON)/deactivate (LED OFF) function:

01.

Activate the extended menu 1.

02.

Press

SEL

button as often as necessary until the

LED T. MOT.

will flashing

03.

Press

SET

button for 1 second

04.

The

LED T.MOT.

on indicates that the function is activated and the

LED

off indi-

cates that the function is disabled.

• T. MOT. |

CLOSING PUSH

• T. MOT. PED |

SAFETY DEVICE 2 / BLOCKING

The function opening push, facilitates the release of the lock when the opening is ac-

tuated, ensuring proper operation.

The control board is supplied by the manufacturer with the opening push disabled.

Activate (LED ON)/deactivate (LED OFF) function:

01.

Activate the extended menu 1.

02.

Press

SEL

button as often as necessary until the

LED INB. CMD. AP.

will flashing

03.

Press

SET

button for 1 second

04.

The

LED INB. CMD. AP

on indicates that the function is activated and the

LED

off

indicates that the function is disabled.

• INB. CMD. AP. |

OPENING PUSH OF

03.

Press

SET

button for 1 second

04.

The

LED CODE PED

on indicates that the function is activated and the LED off indi-

cates that the function is disabled.

The function of programming the remote controls on distance, it allows them to be ad-

ded remote controls to the new control board without having to use the

SEL

button. The

control board is supplied by the manufacturer with programming remote controls on

distance deactivated.

Activate (LED ON) / deactivate (LED OFF) function:

01.

Activate the extended menu 1.

02.

Press

SEL

button once and the

LED AUT/P-P

will begin to flash.

03.

Press for 1 second the

SET

button.

04. LED AUT/P-P

ON indicates that the function is active and the

LED

off indicates that

the function is disabled.

Programming of remote controls on distance:

01.

Press for 10 seconds the button of the remote control a previously memorized.

02. LED CODE

will flash.

03.

Press for 1 second one button of the remote control that you want to program.

04.

The flash lamp will flash confirming the success of the operation.

• AUT/P-P |

PROGRAMMING OF THE REMOTE CONTROL ON DISTANCE

03. CONFIGURATION

EXTENDED MENU 1

EXTENDED MENU 2

The control board is supplied by the manufacturer with an extended menu 2, which

provides access to more functions to the control board.

To access the options menu extended 2 proceed as follows:

01.

Enter the extended menu 1 (see page 06.B).

02.

Press continuously the

SET

button for 5 seconds and the

LED T.PAUSA

and

LED

T. RIT. ANTE

will flash simultaneously.

03.

You have 30 seconds to select functions from the extended menu 2 (using the

SEL

and

SET

button), and after this time the control board returns to the main menu.

EXTENDED MENU 2

LED

LED OFF

LED ON

• AUT/P.P.

Follow Me

OFF

Follow Me

• CODE

Pre Flash Lamp

OFF

Pre Flash Lamp

• CODE PED.

Flash lamp on pause

OFF

Flash lamp on pause

• INB. CMD. AP

Soft start

OFF

Soft start

• T. MOT.

Electronic lock PED

OFF

Electronic lock PED

• T. MOT. PED

PUL=PUL | PED=PED

PUL=AB | PED=FECH

• T. PAUSA.

Intermittent ON/OFF simultaneously

• T. RIT. ANTE

Intermittent ON/OFF simultaneously

With the programmed pause time, it is possible to trigger "Follow Me" option.

With this option enabled, whenever the photocells detected the passage of a user/

object, the control board triggers the closing maneuver after 5 seconds.

Activate (LED ON) / deactivate (LED OFF) function:

01.

Enter the extended menu 2.

02.

Press once the

SET

button and the

LED AUT/P-P

will flash.

03.

Press once

SET

button to enable / disable the function.

The

LED AUT

ON signals that the function is activated and the

LED

OFF signals

that the function is disabled.

• AUT/P-P |

FOLLOW ME

With the functioning in pre flash lamp, the output 03 and 04 (CN2) will always be acti-

vated 3 seconds before the automation start a movement. When disabled, the function

returns flash lamp.

The control board is supplied by the manufacturer with the pre flash lamp disabled.

Activate (LED ON)/deactivate (LED OFF) function:

01.

Enter the extended menu 2.

02.

Press

SEL

button as often as necessary until the

LED CODE

will flashing

03.

Press once

SET

button to enable / disable the function.

The

LED CODE ON

signals that the function is activated and the

LED OFF

signals that

the function is disabled.

• CODE |

PRE FLASH LAMP/LAMP.CORT

With this option enabled, whenever the motor is in pause time at output 230V for flash

lamp will stay on.

The control board is supplied by the manufacturer with the flash lamp paused, disabled.

Activate (LED ON) / deactivate (LED OFF) function:

01.

Enter the extended menu 2.

02.

Press

SEL

button as often as necessary until the

LED CODE PED

will flashing.

03.

Press once

SET

button to enable / disable the function.

The

LED CODE PED ON

indicates that the function is activated and the

LED OFF

signals

that the function is disabled.

• CODE PED |

OPERATION OF OUTPUT 230V FOR FLASH LAMP DURING THE PAUSE TIME

EXTENDED MENU 2

Activate (LED ON) / deactivate (LED OFF) function:

01.

Activate the extended menu 1.

02.

Press

SEL

button as often as necessary until the

LED T. MOT.

will flashing.

03.

Press

SET

button for 1 second.

04.

The

LED T.MOT.

on indicates that the function is activated and the

LED

off indicates

that the function is disabled.

03. CONFIGURATION

EXTENDED MENU 2

The electronic lock on the pedestrian function is used when there is, for example, a

swing doors assembled with electric lock to close the leaf 2. This makes it possible

to obtain the opening of the gate to trigger a push-button connected in PUL, PED or

to trigger the remote control.

The remote control is supplied by the manufacturer with the electronic lock on the

pedestrian function disabled.

Activate (LED ON)/deactivate (LED OFF) function:

01.

Enter the extended menu 2.

02.

Press

SEL

button as often as necessary until the

LED T. MOT.

will flash.

03.

Press once

SET

button to enable / disable the function.

The

LED T. MOT. ON

indicates that the function is activated and the

LED OFF

signals

that the function is disabled.

The control board permits that the PUL input work with a push button (NA) exclusi-

vely for opening and PED input work with a push button (NA) only for closing.

The control board is supplied by the manufacturer with the operation of the PUL

input for connection to a primary push-button (NA) cyclic and PED input for connec-

ting a pedestrian pushbutton (NA) cyclic.

• T. MOT. |

ELECTRONIC LOCK IN PEDESTRIAN FUNCTION

• T. MOT. PED |

OPERATIONS THE INPUTS PUL AND PED

EXTENDED MENU 3

LEVEL OF THE POWER

LEDS ON

AUT/P-P.

AUT/P-P. • CODE

AUT/P-P. • CODE • CODE PED

AUT/P-P. • CODE • CODE PED • INB. CMD. AP

AUT/P-P. • CODE • CODE PED • INB. CMD. AP • T. MOT.

AUT/P-P. • CODE • CODE PED • INB. CMD. AP • T. MOT. • T. MOT. PED

With the extended menu 3 can program the power / motor speed at which will be per-

formed the deceleration.

To access the options menu Extended 3 proceed as follows:

01.

Enter the extended menu 1 (

see page 06.B

02.

Enter the extended menu 2 (

see page 08.A

03.

Continuously press the

SET

button for 5 seconds and the

LED T.PAUSA

and

LED T.

RIT. ANTE

will flash alternately a few moments, past to flash simultaneously immedia-

tely afterwards.

04.

You have 30 seconds to select from the extended menu functions 3 (using the

SEL

and SET button), and after of this time the control board returns to the main menu.

EXTENDED MENU 3

PUL= opening, PED= closing (LED ON) / PUL=PUL and PED=PED (LED OFF):

01.

Enter the extended menu 2.

02.

Press

SEL

button as often as necessary until the

LED T. MOT. PED

will flash.

03.

Press once

SET

button to change the function.

The

LED T. MOT. PED ON

signals that the

PUL

is programmed for opening and

PED

closing. The LED off indicates that the function

PUL

if found programmed to func-

tion with a main push button (NA) cyclic and

PED

input for connecting a pedestrian

pushbutton (NA) cyclic.

With function "Soft Start" enabled, the beginning of each movement, the control board

will control start the motor, increasing power gradually in the first 2 seconds of opera-

tion.

The control board is supplied by the manufacturer with the "Soft Start" disabled.

Activate (LED ON) / deactivate (LED OFF) function:

01.

Enter the extended menu 2.

02.

Press

SEL

button as often as necessary until the

LED INB. CMD. AP.

will flashing.

03.

Press once

SET

button to enable / disable the function.

The

LED INB. CMD. AP. ON

indicates that the function is activated and the

LED OFF

sig-

nals that the function is disabled.

• INB. CMD. AP. |

SOFT START

10A

10B

03. CONFIGURATION

EXTENDED MENU 3

CAPACITORS CONNECTION SCHEME

To detect which components have problems on an automated system, sometimes it is

necessary to conduct tests using a direct connection to a 230V AC power supply. For

this it is necessary to merge a 8μF capacitor to make the automation to work. In the

scheme below is shown how this link should be made and how to merge the different

wires of the components.

NOTES:

• To perform these tests you don’t need to remove the automation from where it is

installed, because this way you can know if connected directly to power supply it will

work correctly.

• The order of wiring capacitor to motor wires is not important, as long you connect

one wire to brown wire of motor and the other one to black wire of motor;

• Common wire should always be connected to power supply.

• To reverse motor direction, just replace black wire with brown wire of the operator

on the power supply.

04. COMPONENT TEST

This test only applies to 230V motors. To test a 24V motor, just connect the

motor cables to a 24V battery.

If you need to restore central with factory setting, press the SEL and SET buttons si-

multaneously. All LEDs will light up temporarily, and when deleted is confirmed the

success of the operation.

The control board is prepared to a safety device connection in accordance with the sec-

tion 5.1.1.6 of standard EN 12453. In every maneuver is performed a test for the Security

Device and the Lock. In case of a function/connection failure the motor doesn’t start

and every LED’s remain in a intermittent mode, indicating the error. When the photoce-

lls operation is corrected, the control board returns to it’s normal functioning. This ac-

tion by the control board allows to recognize failures in accordance with is mentioned

in category 2 of EN 954-1.

In the position corresponding to each transmitter input in low voltage, the control board

has a LED to identify the condition of it. The LED on indicates that the input is closed,

while the LED off indicates that the input is open.

• PHOTOCELLS TEST

• REMOTE CONTROLS TESTE

PHOTOCELLS AND CONTROLS TEST

RESET TO CONTROL BOARD

CAPACITOR 8μF

AUTOMATION

230V POWER

SUPPLY

Earth wire

Brown

Black

Common (Blue)

Motor power programming during the deceleration:

It is possible to choose up to 6 different levels, relatively the force that the motor per-

forms in deceleration. The levels are represented by combinations of the

LED

indicated

in the table above.

Scroll through the

LEDs

with the

SEL

button to set the desired power, knowing that the

LED AUT / P-P. ON

corresponds to minimum power, while the

LEDs AUT / P-P.

CODE

CODE PED

INB. CMD. AP, T. MOT.

T. MOT. PED ON

corresponds to maximum power.

The control board is supplied by the manufacturer with the power regulated at level 3

(

AUT / P-P.

CODE

CODE PED ON

INSTRUCTIONS FOR SPECIALIZED INSTALLERS

05. TROUBLESHOOTING

FINAL CONSUMERS INSTRUCTIONS

Anomaly

Procedure

Behavior

Procedure II

Discovering the origin of the problem

• Motor

doesn't work

• Make sure you

have 230V power

supply connected to

automation and if it is

working properly.

• Still not working

• Consult a qualified

MOTORLINE

technician.

• Motor

doesn’t move

but makes

noise

• Unlock motor and

move the gate by hand

to check for mechani-

cal problems on the

movement.

• Encountered

problems?

• Consult an experienced

gate expert.

1 • Check all motion axis and associated motion systems related with the motor and the gate to find out what is the problem.

• The gate moves

easily?

• Consult a qualified

MOTORLINE

technician.

• Motor opens

but doesn’t

• Unlock motor and

move the gate by hand

to closed position.

Lock motor again and

turn off power supply

for 5 seconds. Recon-

nect it and send order

to open gate using

transmi- tter.

• Gate opened but

didn’t close again.

1 • Check if there is any

obstacle in front of the

photocells;

2 • Check if any of the control

devices (key selector, push

button, video intercom, etc.)

of the gate are jammed and

sending permanent signal to

control unit;

3 • Consult a qualified

MOTORLINE

technician

• Gate doesn’t

make

complete

route

• Unlock motor and

move gate by hand to

check for mechanical

problems on the gate.

• Encountered

problems?

• Consult an experienced

gate expert.

1 • Check all motion axis and associated motion systems related with the gate to find out what is the problem.

• The gate moves

easily?

• Consult a qualified

MOTORLINE

technician.

1 • Open control board and check

if it hás 230V power supply;

2 • Check the control board input

fuses;

3 • Disconnect the motor from

control board and test them by

connecting directly to power

supply in order to find out if they

have problems

(see page 10.B).

4 • If the motor works, the

problem is on the control board.

Pull it out and send it to our

MOTORLINE

technical services

for diagnosis;

5 • If the motor doesn’t work,

remove them from installation

site and send to our

MOTORLINE

technical services for diagnosis.

1 • Check capacitors, testing

operator with new capacitors;

2 • If capacitors are not the

problem, disconnect motors from

control board and test them by

connecting directly to power

supply in order to find out if they

have problems (

see page 10.B

);

3 • If the motors work, the

problem is from control board.

Pull it out and send it to our

technical services for diagnosis;

4 • If the motors doesn’t work,

remove them from installation

site and send to our

MOTORLINE

technical services for diagnosis.

1 • Check capacitors, testing with

new capacitors;

2 • If capacitors are not the

problem, disconnect motor

from control board and test it

by connecting directly to power

supply in order to find out if it is

broken;

3 • If the motor doesn’t work,

remove it from installation site

and send to our

MOTORLINE

technical services for diagnosis.

4 • If motor work well and move

gate at full force during the entire

course, the problem is from

controller. Set force using

trimmer on the board. Make a

new working time programming ,

giving suffient time for opening

and closing with appropriate

force (page 08.B).

5 • If this doesn’t work, remove

control unit and send it to

MOTORLINE

technical services

services.

NOTE:

Setting force of the controller

should be sufficient to make the

gate open and close without

stopping, but should stop and

invert with a little effort from a

person. In case of safety systems

failure, the gate shall never cause

physical damaged to obstacles

(vehicles, people, etc.).

All

MOTORLINE

control boards have LEDs that

easily allow to conclude which devices are

with anomalies. All safety devices LEDs (DS)

in normal situations remain On. All "START"

circuits LEDs in normal situations remain Off.

If LEDs devices are not all On, there is some

security systems malfunction (photocells,

safety edges), etc. If "START" circuits LEDs

are turn On, there is a control device sending

permanent signal.

A) SECURITY SYSTEMS:

1 • Close with a shunt all safety systems

on the control board (check manual of the

control board in question). If the automated

system starts working normally check for the

problematic device.

2 • Remove one shunt at a time until you find

the malfunction device.

3 • Replace it for a functional device and

check if the motor works correctly with all the

other devices. If you find another one

defective, follow the same steps until you find

all the problems.

B) SISTEMAS DE START:

1 • Disconnect all wires from START terminal

input.

2 • If the LED turned Off, try reconnecting one

device at a time until you find the defective

device.

NOTE

: In case procedures described in

sections A) and B) don’t result, remove control

board and send to our technical services for

diagnosis.

SERR.

PED

L N

LAMP 230V

RE 1

AP COM CH

RE 2

AP COM C

PUL

PED

DS1

DS2

12/24V

12/24V

COM

SEL

SET

AUSA

PED

INB.

CODE PED

CODE

P-

06. CONNECTION SCHEME

CONTROL BOARD CONNECTION COMPONENT

Int

erior Pho

tocells

Ext

erior Pho

tocells

tor 1

tar

ts opening be

for

e Mo

tor 2 -

tor 2

tar

ts cl

osing be

for

e Mo

tor 1

- It mus

t be ap

plied an 8

μ capacit

or in

eac

h mo

tor

, on the opening and cl

osing

wir

es as e

xplained abo

TE •

If an

y one o

f the mo

tor

s mo

ves in

the wr

ong w

, jus

t s

wit

ch the br

own and

blac

k cabl

es o

f tha

t mo

tor t

o c

hang

e the

dir

tion.

Compl

Opening (2 lea

ves)

Ligh

t Bulb

Ant

enna

Earth wire

Black

Brown

Earth wire

Blue

Brown

Black

edes

trian

Opening (1 leaf)

tor 1

tor 2

- F

ça +

For