Full Text Searchable PDF User Manual
Operation Manual
Touch- style key wired controller
KJR-29B/BKE-E
OPERATION MANUAL
KJR-29B/BKE-E
3
CONTENTS
1. Safety Precautions ............................................................................... 5
2. Model and Specification ...................................................................... 6
3. Buttons And Their Functions ............................................................... 7
4. Installation ......................................................................................... 10
5. Wiring................................................................................................. 11
OPERATION MANUAL
KJR-29B/BKE-E
4
1. Precautions
The following contents are stated on the product and the operation manual, including usage,
precautions against personal harm and property loss, and the methods of using the product
correctly and safely. After fully understanding the following contents (identifiers and icons), read
the text body and observe the following rules.
Warning
Means improper handling may lead to personal severe injury.
Caution
Means improper handling may lead to personal injury o property
loss.
OPERATION MANUAL
KJR-29B/BKE-E
5
2. Model And Specification
Model
KJR-29B/BKE-E
KJR-29B
Power Supply Voltage
5.0V DC
Ambient Temperature Range
-5°C
～
+43°C
Ambient Humidity Range
RH40%~RH90%
Performance features
1. Operating mode: Cool, heat, dry, fan and auto.
2. Set the mode through buttons.
3. Indoor setting temperature range: 17°C ~30°C.
4
.
LCD (Liquid Crystal Display).
5. Touch-style key
Function summarize
KJR-29B/BKE-E
is the touch-style key wired controller.
New function
Basic function
Air filter cleaning reminding function
ON and OFF the air-conditioner
Indoor unit address setting function
Auto-restart function
Remote control receiver function
Time ON and Time OFF setting
Lock the wired controller
Clock setting
Quiet operation
Setting the Operating mode, Temperature
Follow me
Fan speed and Swing functions
OPERATION MANUAL
KJR-29B/BKE-E
6
3. Buttons And Their Functions
(1) Remote signal receiving function
There is the signal receiver for wireless remote controller on the KJR-29B.You can use the
wireless remote controller to control the air-conditioner through the wired remote controller when
the system has been powered on.
Notes:
The wired controller will not receive the swing controlling instruction. For the indoor unit with swinging
function, you can directly use the remote controller to control swinging through the display panel of the indoor unit,
or use the swing button on the wired remote controller to control the indoor unit for swinging.
(2) ON/OFF button
Press the ON/OFF button to control the indoor unit on and off status. When the unit is turned off,
press the ON/OFF button, the unit will be turned on and the operating icon lights up. When the
unit is turned on, press the ON/OFF button, the unit will be turned off and the operating icon lights
off.
(3) Mode button
Press the mode button to set the operating mode, after each button press the operation mode will
circle as follow:
When the controller has been set to cool-only, then there is no HEAT mode.
(4) Fan speed setting
Under COOL, HEAT and FAN modes, press the fan speed button can adjust the fan speed
setting. After each fan speed button press will circle as follow:
AUTO
→
LOW
→
MID
→
HIGH
→
AUTO
Under AUTO and DRY modes, the fan speed is not adjustable and the default fan speed is auto.
AUTO
COOL
DRY
HEAT
FAN
OPERATION MANUAL
KJR-29B/BKE-E
7
(5)Temperature setting
Under AUTO, COOL, DRY, HEAT modes, press the Temp adjust Up/Down buttons to set the
temperature, the adjusting range is 17
℃
~30
℃
(or 62
℉
~88
℉
). The setting temperature cannot be
adjusted under FAN mode.
(6)Timer on and Timer off setting
Press the timer/clock setting button, then enter into the timer on setting status, and the screen will
display timer icon
and
.
You can press Temperature setting buttons to adjust the time. When the time setting is less than
10 hours, each press the Temp setting buttons will increase or decrease 0.5 hour. When the timer
setting is more than 10 hours, each press Temp setting buttons will increase or decrease 1 hour,
the maximum timer setting is 24 hours. After finish adjusting the time on setting, press the
26
℃
/OK button or wait for 5 seconds to confirm and exit the time on setting.
Notes: I
f the wired remote controller has been set timer on/ off, press the ON/OFF button to turn on/ turn off the
unit then the timer will be canceled simultaneously
.
(7) Clock setting
Long press the timer/clock setting button for 3 seconds, and then enter into the clock setting
status. The hour position of the clock will flash, and can press Temp setting buttons to adjust the
hour value.
After finish the hour setting, press left button or right button to switch to minute position setting,
then the minute position will flash, press Temp setting buttons to adjust the minute value. After
finish the clock setting, press the button or wait for 5seconds to confirm and exit the setting state.
(8)Quiet/OK button
Under the cooling, heating and auto mode, when operate the quiet mode, it can reduce the
running noise through setting the fan speed to low. This will help you bring a quieter environment.
Under AUTO, DRY mode, the fan speed is auto and the Quiet /OK button doesn’t work.
(9) Wired controller locking
Press the temperature adjusting UP and DOWN buttons simultaneously, the wired controller
enters into locking state, and the locking icon will be lighted up. Under the locking state, the wired
controller will not respond to buttons by pressing and the control instruction from the wireless
remote controller. Simultaneously press temperature adjusting buttons again will cancel the
locking state.
OPERATION MANUAL
KJR-29B/BKE-E
8
(10) Air filter cleaning reminding function
The wired controller records the total running time of the indoor unit, when the accumulated
running time reaches the pre-set value, air filter cleaning reminding icon will be lighted up, to
remind that the air filter of the indoor unit needs to be cleaned. Long press left button for 3
seconds, and clear the reminding icon and the wired controller will re-accumulate the total
running time of the indoor unit.
Notes:
The default setting value of reminding function is 2500 hours, and it can change to be 1250 hours, 5000
hours or 10000 hours. The setting methods please refer to the installation manual.
(11)Swing function
If the indoor unit supports swing function, press the right button to adjust the air outlet direction of
the indoor unit. Long press this button for 3 seconds can turn on or turn off the auto-swing
function. When the auto-swing function is turned on, the swing icon will be lighted up.
(12)Follow me function
When the system is running and the operating mode is AUTO. COOL or HEAT, press the left
button will activate the Follow Me function. Press left button again will cancel follow me function.
When the operating mode is changed, and then will cancel this function as well. When the Follow
Me function is activated, the icon will be light up, and the wired controller will display room
temperature read from the local sensor, and transmit the temperature value to the indoor unit
every 3 minutes.
(13) Setting addresses
§
Press the Temp. UP and DOWN button simultaneously for more than 8 seconds, then the
controller gets into address setting mode.
§
In the address setting mode, there are 2 main functions:
§
Querying address: Press MODE button, the corresponding indoor unit will display its
address.
§
Setting address: Use the UP and DOWN buttons to choose an address you want. Then
press the FAN button to set the indoor unit's address. The corresponding indoor unit will
display the new address and record it. After about 4 seconds, this displaying will fade out
and indoor units turn to normal display mode.
§
After setting addresses, users can press the Quiet/OK button can exit the address setting
mode.
§
After each setting address and enter the query / set mode again, it will display the last set of
address, but if re-power, this address will be cleared.
§
In the address setting mode, wired controller does not respond to any command from remote
controller.
OPERATION MANUAL
KJR-29B/BKE-E
9
4. Installation
※
Preparation before Installation:
Make sure the following pasts has been prepared.
NO.
Name
QTY.
Remarks
1
Wired Controller
1
/
2
Cross round heat wood
Mounting Screw
3
M4×20(For mounting on the wall)
3
Cross round heat
mounting Screw
2
M4×25(For mounting on the electrical switch box)
4
Installation Manual
1
/
5
Owner's Manual
1
/
6
Plastic expansion pipe
3
For mounting on the Wall
7
Plastic screw bar
1
For fixing on the 86 electrician box
8
Switching wires for
signal receiving board
1
For connecting the signal receiving board
and 4-core shielding wire
9
Switching wires for wired
controller signal
1
(If needed) For connecting the main control
panel and 4-core shielding wire
※
Prepare for the following at installation site.
NO.
Name
Qty.(embedded
into wall)
Specification remarks
(only for reference)
Remarks
1
4-core Shield Cable
1
RVVP-0.5 mm
2
×4
0.05 mm
2
×5 cable
no more than 12M
2
86 electrician box
1
/
/
3
Wiring Tube(Insulating
Sleeve and Tightening
Screw)
1
/
/
※
Dimensions:120*120*20mm
Figure A
OPERATION MANUAL
KJR-29B/BKE-E
10
5. Wiring
※
Wiring principle sketch:
※
Wiring figure:
1) Connect two terminals of embedded 4-core shielding wire with the switching wires of wired
remote controller and signal receiving board. Make sure the sequence of 4 terminals (A/B/C/D)
should correspond to the wire sequence of signal switching wires (A/B/C/D).
2) If embedded 4-core shielding wire cannot go through the wired controller, it can use signal
switching for connection and make sure the wires are reliable and firm. The tightening torque
range of the screw is0.8~1.2N .m (8~12 kgf . cm).
※
Back cover installation
1) Use straight head screwdriver to insert into the buckling position in the bottom of a wired
controller, and spin the screwdriver to take down the back cover. (Pay attention to spinning
direction, if not you maybe damage the back cover.)
C
D
A
B
C
D
A
B
C D
A B
+5V
GND
IR+
IR-
4-core shielding wire embedded in the wall
Attached connecting wires for the signal receiving panel
Signal receiving panel
Front cover
Control panel
Screw
Signal switching wire
4-core shielding wire
embedded in the wall
Attached connecting wires for
the signal receiving panel
OPERATION MANUAL
KJR-29B/BKE-E
11
2) Use three GB950-86 M4X20 screws to directly install the back cover on the wall.
3) Use two M4X25 GB823-88screws to install the back cover on the 86 electrician box, and use
one GB950-86 M4X20 screw for fixing the wall.
4) Adjust the length of two plastic screw bars in the accessory to be the standard length from the
electrical box screw bar to the wall. Make sure when install the screw bar to the electrical box
screw bar, make it as flat as the wall.
Buckling position
Back cover
Front cover
Straight head screwdriver
Screw hole installed on
the wall,use three
GB950-86 M4X20
Screw hole fixed on
the wall,use one
GB950-86 M4X20
Screw hole installed
on 86 Electrician box,
use two
86 Electrician box
Signal switching wires
Back cover
OPERATION MANUAL
KJR-29B/BKE-E
12
Notes:
1.Use cross head screws to fix the wired controller bottom cover in the electric control box through the
screw bar. Make sure the wired controller bottom cover is on the same level after installation, and then install the
wired controller back to the bottom cover.
2. Over fasten the screw will lead to deformation of the back cover.
※
Wiring
1) Wiring, three outlet positions
2) Shielded wiring
OPERATION MANUAL
KJR-29B/BKE-E
13
※
Front cover installation
1) After adjusting the front cover and then buckle the front cover; avoid clamping the communication
switching wire during installation.
2) Correct install the back cover and firmly buckle the front cover and back cover, if not you maybe
make the front cover drop off.
※
Wired controller initial parameters setting:
1.
Change the related functions of the controller through adjusting the initial parameters, details refer to
table 1
2. The wired controller initial parameter includes two codes "XY", the first code "X" means function
class, and the second code "Y" means the detailed configuration of this function.
3. Setting method:
1
）
Simultaneously press "Mode" and "Fan" button of the wired controller for 5 seconds to enter the
parameter setting state;
2) The value of this first code "X" is "0"; press the temperature setting button UP and DOWN to adjust
the second code value;
3) After setting the second code value, press 26/OK button to switch the first code to the next value;
4) When the first code value is "6", press 26/OK button again to exit the parameters setting.
4. The parameters setting function only under the situation which needs to adjust the default functions'
setting states; otherwise there is no need to do the setting.
Table 1
First
code
Functions
Second code
0
1
2
3
4
0
Cool-only/ Cool-Heat
selection
Cool-Heat
(Default)
Cool-only
/
/
1
Indoor unit communication
address setting
Yes (Default)
None
/
/
/
2
Auto-restart
Yes (Default)
None
/
/
/
3
Air filter cleaning reminding
function
Cancel the
reminding
function
1250 hours
2500 hours
(Default)
5000
hours
10000
hours
5
Remote receiving function
Yes (Default)
None
/
/
/
6
Centigrade/
Fahrenheit display
Centigrade
Fahrenheit
/
/
/
OPERATION MANUAL
KJR-29B/BKE-E
14
15
